Technical Guide. USB 3.0 xhci-based Certification Platform and PDK

Transcription

1 Technical Guide USB-IF USB 3.0 Peripheral Development Kit: USB-IF xhci-based PDK USB3.0 certification Platform USB 3.0 xhci-based Certification Platform and PDK January 30, 2014 Revision 1.9

2 About this Document Content Owner Author Approval Body SuperSpeed USB Compliance Martin Franke, Anthony Knapp, Sydney Fernandes Abdul Ismail Revision History Revision 1.0 Revision 1.1 Revision 1.2 Revision 1.3 Revision 1.4 Revision 1.5 Revision 1.6 Revision 1.7 Revision 1.8 Revision 1.9 Release Added information about USB30CV and Drivers Added information about UAC with USB30CV Added information about USB30CV installation, equipment setup with the NEC (Renesas) xhci Updated information about USB30CV documentation and updated contact information for the USB-IF Technical Support Updated information about USB30CV directory structure Updated information about USB30CV driver names, updated installation settings required for 64-bit operating systems and updated Renesas PDK jumper settings Updated information about PDK Jumper Settings Updated to xhci spec version 1.0 based PDK boards. Added information based on use of Stack Switcher Removed Renesas PDK. Added Dell XPS8700 certification testing platform. Modifications to Dell XPS8700 system for certification testing. USB 3.0 xhci-based Certification Platform and PDK 2 Rev 1.9 January 30, 2014

3 Table of Contents 1. INTRODUCTION REFERENCES WORKSTATION PREPARATION FOR PDK Fresco PDK System Requirements Hardware Hardware Installation PDK Assembly PDK System Installation USB 3.0 CERTIFICATION PLATFORM PREPARATION DELL XPS8700 Configuration System Modification SOFTWARE SETUP TROUBLESHOOTING USB 3.0 xhci-based Certification Platform and PDK 3 Rev 1.9 January 30, 2014

4 Acronyms ESD DUT FW HW I/O MB NC OS PC PCB PCI PCIe PCLK PDK PHY UAC USB USB-IF xhci Electro Static Discharge Device Under Test Firmware Hardware Input / Output Motherboard No Connection Operating System Personal Computer Printed Circuit Board Peripheral Component Interconnect PCI Express. Refer to the PCIe specification PHY Clock Signal Peripheral Development Kit Physical Layer User Account Control Universal Serial Bus Universal Serial Bus Implementers Forum extensible Host Controller Interface USB 3.0 xhci-based Certification Platform and PDK 4 Rev 1.9 January 30, 2014

5 1. INTRODUCTION The USB-IF uses the DELL XPS8700 system for USB3.0 Certification. Testing is performed using the on-board Intel xhci host controller. This document provides information and instructions to modify the USB 3.0 certification platform. Furthermore the document also provides information and instructions to implement a USB 3.0 workstation with the Fresco Logic xhci PDK. The system hardware specifications and software installation have been tested by qualified hardware technicians. Deviation from these instructions may result in unpredictable behavior in the USB 3.0 certification platform. This document is not a substitution for any referenced documentation. The procedures should be performed by a qualified technician only. USB 3.0 xhci-based Certification Platform and PDK 5 Rev 1.9 January 30, 2014

6 2. REFERENCES The references given here are mentioned throughout this documentation: Specification Revision 1.0: USB-IF Company List: USB-IF estore: USB 3.0 xhci-based Certification Platform and PDK 6 Rev 1.9 January 30, 2014

7 3. WORKSTATION PREPARATION FOR PDK 3.1. Fresco PDK System Requirements For best results when using a PDK the recommended minimum system requirements are: Intel Desktop Board (or equivalent) with available PCIe Gen2 Slot Intel Core i5, 2.40GHz or faster processor 2048MB of RAM or higher 40GB or Higher Hard Disk with 10GB of free space Microsoft Windows 7 Operating System with Service Pack Hardware Peripheral Development Kit (PDK) Add-in Card is available from the USB-IF e-store (see USB-IF estore from chapter 2): Fresco Logic xhci-based PDK PCIe Card 4-Pin Molex Connector for External Power JP9: Up - PCIe Powered Down - Externally Powered Figure 1: Fresco Logic FL1100 Rev 1.1 PDK USB 3.0 xhci-based Certification Platform and PDK 7 Rev 1.9 January 30, 2014

8 In addition an external power supply with a 4-pin Molex receptacle is also required such as that shown in Figure 2. This power supply must be capable of providing power separately from the PC Hardware Installation PDK Assembly Figure 2: Example of an External Power Supply Prior to installation of the Fresco controller, set the jumpers to the configuration shown in Figure 3 if not already done. PCIe Connector Figure 3. FL1100 Jumper Settings USB 3.0 xhci-based Certification Platform and PDK 8 Rev 1.9 January 30, 2014

9 PDK System Installation Installing the Fresco xhci-based PDK board: 1. Shutdown the PC. Use caution anytime hardware is removed or inserted into a computer system. 2. Unplug the power cord from the PC system before attempting to remove or insert the PDK. 3. Attach an external power supply to the PDK s 4-pin Molex Connector. (An external supply is needed in order to maintain active V-Bus during system sleep states) 4. Power on the external power supply. 5. Power on the PC. 6. When the system has finished booting the OS should recognize new hardware is attached and unsuccessfully attempt to install a driver. USB 3.0 xhci-based Certification Platform and PDK 9 Rev 1.9 January 30, 2014

10 4. USB 3.0 CERTIFICATION PLATFORM PREPARATION 4.1. DELL XPS8700 Configuration For best results when purchasing the DELL XPS8700 the recommended minimum system requirements are: Intel Core i7 (4 th Generation), 3.40GHz or faster processor 8 GB of RAM or higher 64GB or Higher Hard Disk with 10GB of free space Microsoft Windows 8.1 Operating System 4.2. System Modification DELL XPS8700 is shipped standard with an add-on Graphics Card, Wireless Mini-Card and Media-Card Reader. These items should be removed before using the system for testing. Modification Steps: Step 1 Enable Integrated Graphics by doing the following: Power on the system Press F2 when you see Dell logo onscreen Highlight Advanced -> Onboard Device Configuration and press Enter Highlight Intel Multi Display option and Enable it if it is disabled Step 2 Follow the DELL XPS8700 Owner s Manual for the modifications listed below: Remove the Graphics Card and connect the Display Monitor to Integrated Graphics HDMI port Remove the Wireless Mini-Card Remove the Media-Card reader Step 3 Do a fresh install of Windows 8.1. Be sure to delete all partitions on the hard drive beforehand. After Windows 8.1 is installed, complete the Windows Updates. Drivers and BIOS for the system can be found at Install Intel Z87 Chipset Drivers. Install Intel Graphics Driver. Install Intel Rapid Storage Technology. Install Intel Management Engine Components. It is recommended to save a system image at this point. USB 3.0 xhci-based Certification Platform and PDK 10 Rev 1.9 January 30, 2014

11 Step 4 The DELL XPS8700 is a Legacy Free system, all USB ports are controlled by the Intel xhci controller. When USB-IF tools like CV are launched control of Mouse and Keyboard will be lost. To avoid this issue install a secondary PCIe USB card and connect the mouse and keyboard to the USB ports on it. USB 3.0 xhci-based Certification Platform and PDK 11 Rev 1.9 January 30, 2014

12 5. SOFTWARE SETUP The USB30CV software is proprietary software provided by the USB-IF or their representative. Find more information regarding proprietary software setup at the USB-IF website: Host Controller Driver Installation for Fresco PDK If configuring PDK as a host controller obtain driver from the USB-IF (see Software Tools and PDK Drivers from chapter 2) and install using installation wizard. Verify that U1/U2 low power states and LPM L1 are enabled: Fresco Double click the provided file FrescoU1U2Enable-LPMEnable.reg Restart system to apply changes. If the driver does not install correctly, there may be an issue with the driver signature and it may need to be installed manually. See section Error! Reference source not found. for details Command Verifier Installation If configuring system for use with the CV tool be sure that User Account Control (UAC) is disabled: In Control Panel window select User Accounts In the User Accounts menu select User Accounts In the User Accounts menu select Change User Account Control Settings Set notification status to Never notify and click ok Reboot the system Install the USB30CV software available from the SuperSpeed USB Tools site (see Software Tools and PDK Drivers from chapter 2) CV Stack Switcher Under normal operation the CV software will automatically install the compliance driver in place of any other host controller driver when CV is opened. When CV is closed properly it will remove the compliance driver and allow Windows to automatically install whichever driver takes priority based on Windows internal driver installation algorithm. This process is accomplished using a tool called Stack Switcher. When the compliance driver is correctly installed, it will be viewable from device manager as shown in Figure 4. USB 3.0 xhci-based Certification Platform and PDK 12 Rev 1.9 January 30, 2014

13 Figure 4: Compliance Driver 6. TROUBLESHOOTING Issue Possible Cause Solution Fresco PDK does not appear in Device Manager JP9 on the PDK board is in the down position but no external power is applied to the PDK. Power the PC down and apply external power to the PDK then boot the system again. See section 3.3 for details. For technical support, contact the USB-IF at USB 3.0 xhci-based Certification Platform and PDK 13 Rev 1.9 January 30, 2014

14 THIS DOCUMENT IS PROVIDED WITH THE PDK "AS IS" WITH NO WARRANTIES WHATSOEVER, INCLUDING ANY WARRANTY OF MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR ANY PARTICULAR PURPOSE, OR ANY WARRANTY. ALL WARRANTIES ARE EXPRESSLY DISCLAIMED. USER ASSUMES THE FULL RISK OF USING THIS DOCUMENT. IN NO EVENT SHALL USB-IF BE LIABLE FOR ANY ACTUAL, DIRECT, INDIRECT, PUNITIVE, OR CONSEQUENTIAL DAMAGES ARISING FROM SUCH USE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. USB 3.0 xhci-based Certification Platform and PDK 14 Rev 1.9 January 30, 2014