MODEL BQ TECHNICAL BULLETIN BQ-TB BACK PRESSURE / RELIEF REGULATOR FEATURES APPLICATIONS CAUTION
|
|
|
- Madeleine Beatrix Allen
- 7 years ago
- Views:
Transcription
1 TECHNICAL BULLETIN MODEL BQ BACK / RELIEF REGULATOR The Model BQ is a relief regulator suitable as a back pressure regulator or bypass valve for controlling inlet pressures between 5 and 300 psig (.34 to 20.7 Barg). For 1/4", 3/8" or 1/2" (DN8, 10, and 15) process piping. Avail able options include cryogenic construction and dif fer en tial/ pressure loaded construction. FEATURES Versatile: High Capacity: Tight Shut Off: Four body materials and nineteen trim material combinations allow com pati bil i ty with many fl uids. A large orifi ce and diaphragm provide sensitivity with high ca pac i ty. A composition seat is available in sev er al materials. APPLICATIONS MODEL BQ Designed for controlling a wide range of fl uids in cluding air, inert gases, cryogenic gas or liquids, chem i cals, water, fuel oil and steam. See Table 1 for more in for ma tion. CAUTION This is not a safety device and must not be substituted for a code approved pressure safety relief valve or a rupture disc.
2 STANDARD/GENERAL SPECIFICATIONS Body Sizes: Body/Spring Chamber Material Combinations: 1/4", 3/8" or 1/2" (DN8, 10, or 15) inlet and fl ow-thru connections. 1/2" (DN15) outlet bottom connection. NPT female only. DI/DI, BRZ/DI, BRZ/BRZ, CS/SST, SST/SST. DI = Ductile iron CS = Cast carbon steel BRZ = Cast bronze SST = Cast stainless steel See Table 2 for material spec i fi ca tions. Cont'd Diaphragm: Tables show capacities of 10, 20, 30, 40 and 50% build-up over the set pressure. Set pressures were de ter mined using a fl ow rate of 2% or less of the 20% build-up capacities. Ex am ple: 100 psig (6.89 Barg) set pressure and a 20% build-up = 120 psig (8.27 Barg) fl owing pressure for the capacity listed. Phosphor Bronze, Neoprene (BC), Fluorocarbon Elastomer (FKM) EPDM, SST TFE coat ed SST, Elgiloy. Inlet Pressure: Operating Temperature: Up to 400 psig (27.6 Barg). (In cludes 100 psi (6.9 Barg) pressure build when set at 300 psig (20.7 Barg) under low fl ow rate.) See Table 2. See Tables 2, 3, and 4. Gasket: Range Springs: Standard: Graphite/NBR. NOT SUIT- ABLE FOR OX Y GEN SER VICE. Alternate Material: See Opt-45. Standard: Cryogenic: Epoxy Coated Steel. SST. Trim Design: Capacities: Metal seated or composition seated brass or SST materials. See Figures 1 and 2, and Tables 3 and 4. Up to 2 C v; see Table 5 for C v vs. set pressure. Water Flow - see Table 6. Compressed Air Flow - see Table 7. Flange Bolting: STANDARD CRYOGENIC STEEL RANGE SPRINGS SST RANGE SPRINGS psig (Barg) psig (Barg) 5-15 ( ) 5-15 ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) Standard: Zinc plated; heat treated steel. Cryogenic: SST. Painting: Standard: All non-corrosion resistant portions to be painted with corrosion resistant epoxy paint per Cashco Spec #S Alternate: See Opt-95 or -95OS. Figure 1: Standard Metal Seat Design Figure 2: Composition Seat Design 2
3 OPTION SPECIFICATIONS OPTION -1: CLOSING CAP. A removable cast iron cap dis cour ag es tam per ing with spring set ting. Avail able only with DI or SST spring cham ber materials. In cludes a 1/4" (DN8) NPT female vent con nection. OPTION -25: OPTION -25S: VENT TAP. Spring chamber vent tapped 1/4" (DN8) NPT female for remote venting. VENT SCREEN. Cap. (For Opt-25) OPTION -1+6: DIFFERENTIAL CONSTRUCTION. For dif fer en tial or pressure loaded service; in cludes fea tures of Opt-1 plus a gasket for sealing the closing cap to the spring chamber, a thread seal for the lock nut, a pusher plate and a top-side di a phragm gas ket (metal di a phragms only). The pressure loading, plus the spring setting, plus build-up to stroke the plug must not exceed pressures listed Table 2. CAUTION Option-1+6 contains single di a phragm con struc tion. In the event of diaphragm fail ure, the process flu id will mix with the load ing fluid. Please alert your rep re sen ta tive so an al ter na tive product can be se lect ed. OPTION -36: OPTION -45: OPTION -55: SST CRYOGENIC CON STRUC TION. Same spec i fi ca tions as Opt-5 ex cept: a. For SST/SST body/spring cham ber materials. b. S1 and S36 only available trim se lec tions. TFE GASKETS. Primarily for ox y gen ser vice. Tem per a ture range: -20 to +400 F (-29 to +205 C). SPECIAL CLEANING. BRZ or SST body ma te ri als only. Cleaned per Cash co Spec. #S-1134 for ox y gen ser vice. NOTE: De sign Pressure Rating shall not exceed 375 psig (25.8 Barg) when body material is SST and process medium is oxygen. OPTION -5: BRASS/BRONZE CRYOGENIC CON STRUC TION. BRZ/BRZ Body/ spring cham ber ma te ri als only. Brass ad just ing screw, lock nut, pressure plate and spring button. SST range spring and fl ange bolting. Only B0 and B5 trim selections al lowed. Cleaned and pack aged for oxygen service per Cashco Spec. #S Spring chamber has 1/4" NPT female connection for purge gas plus a 1/8" drilled drain hole. Mount in hor i zon tal piping with the adjusting screw oriented downwards. Ap pli ca ble tem per a ture range -325 F to+150 F(-198 C to +66 C) OPTION -56: OPTION -95: OPTION -95OS: SPECIAL CLEANING. DI, CS, or SST body ma te ri als only. Cleaned per Cash co Spec. #S Not suit able for ox y gen ser vice. EPOXY PAINT. Special epoxy painting of all non-corrosion resistant external surfaces per Cashco Spec #S Utilized in harsh atmospheric conditions. EPOXY PAINT. Special epoxy painting of all non-corrosion resistant external surfaces per Cashco Spec #S-1687 for OFFSHORE installations. 3
4 TECHNICAL SPEC I FI CA TIONS TABLE 1 APPLICATIONS FLUID RECOMMENDED CONSTRUCTION TRIM DESIGNATION NUMBER Air or Inert Gases Composition Seat and Diaphragm B2, B3 or BB Chemical Metal Seat and Diaphragm Metal Seat and Composition Diaphragm Composition Seat and Metal Diaphragm Composition Seat and Diaphragm S0,S1, or S40M S5, S40 S9 or S36 S3, S40T or SB Cryogenic Gas or Liquids TFE Seat and Metal Diaphragm B5 or S36 Metal Seat and Diahragm B0 or S1 Fuel Oil Composition Seat and Diaphragm BB, B4, S3 or SB Hydrocarbon Gas or Liquids Composition Seat and Diaphragm BB, B4, S3, S3N or SB Steam, All Pressures, Saturated or Superheated Metal Seat and Diaphragm B0 or S1 Water and Condensate Low Temperature F (0-83 C) Composition Seat and Diaphragm BB, B2, B3, S3, S3N or SB Water and Condensate Composition Seat and Diaphragm B6 High Temperature F( C) Metal Seat and Diaphragm B0 or S1 NOTE: Trim Designation Nos. in "boldface" are the most commonly used. Cashco, or its representatives may make rec ommen da tions or suggestions as to the suitability of certain trims for specifi c services. These are trims that have been used successfully in the past in similar applications. However, the user has fi nal responsibility for materials selected. TABLE 2 BODY AND SPRING CHAMBER MAXIMUM WITH TEMPERATURE RATINGS MATERIAL SPECIFICATIONS (Body / Spring Chamber) INLET Description (Abbr.) DI/DI BRZ/DI BRZ/BRZ 1 ASTM No. A395 B62 Alloy C83600/ A395 B62, Alloy C83600 Pressure Temperature Psig (Barg) F C (27.6) (20.7) (17.2) (27.6) (20.7) (17.2) -20 to to (-29 to +135) (+205) (+232) (-29 to +66) (+177) (+205) A216, Gr. WCB/ CS/SST A351, Gr. CF8M 400 (27.6) -20 to +600 (-29 to +315) SST/SST A351, Gr. CF8M NOTE 1: For operating temperatures between -325 to +150F (-198 to +66 C), specify Opt-5 with trim B0 or B5, or Opt-36 with trim S1 or S36. 4
5 TABLE 3 BRASS TRIM MATERIAL COMBINATIONS PART BRASS TRIM DESIGNATION NUMBER BO* B1 B2 B3 B4 B5* B6 BB Cylinder Brass Brass Brass Brass Brass Brass Brass Brass Piston Brass Brass Brass Brass Brass Brass Brass Brass Seat Disc None (Metal) None (Metal) NBR TFE TFE TFE EPR NBR Pin None None Brass Brass Brass Brass Brass Brass Diaphragm Phos. Brz. 302 SST BC BC FKM Phos. Brz. EPDM NBR Temperature -20 to to to to to to to to +180 Range F ( C) (-29 to +94) (-29 to +205) (-29 to +83) (-29 to +83) (-29 to +205) (-29 to +93) (-29 to +149) (-29 to +83) * For operating temperatures between -325 to +150F (-198 to +66 C), specify Opt-5 and trim B0 or B5. TABLE 4 STAINLESS STEEL TRIM MATERIAL COMBINATIONS PART STAINLESS STEEL TRIM DESIGNATION NUMBER SO S1* S3 S3N S5 S9 S36* S40 S40M S40T SB Cylinder 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST Piston 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST 316 SST Seat Disc None (Metal) None (Metal) TFE NBR None (Metal TFE TFE None (Metal) None (Metal) TFE NBR Pin None None 316 SST 316 SST None None None 316 SST 316 SST Diaphragm TFE coated 302 SST 302 SST BC BC FKM TFE coated 302 SST 302 SST BC Elgiloy FKM NBR Temperature -20 to to to to to to to to to to to +180 Range F ( C) (-29 to +205) (-29 to +205) (-29 to +83) (-29 to +83) (-29 to +205) (-29 to +205) (-29 to +205) (-29 to +83) (-29 to +205) (-29 to +205) (-29 to +83) * For operating temperatures between -325 to +100F (-198 to +38 C), specify Opt-36 and trim S1 or S36. ABBREVIATIONS NBR = Buna-N BC = Neoprene EPR = Ethylene Propylene EPDM = Ethylene Propylene Diene TFE = Polytetrafl uoroethylene FK = Fluorosilicone FKM = Fluorocarbon elas tomer TFE = Polytetrafluoroethylene Phos BRZ = Phosphor Bronze TABLE 5 C v FOR SET S PLUS BUILD (F L = 0.945) SETPOINT METAL DIAPHRAGM COMPOSITION DIAPHRAGM BUILD-UP OVER SET BUILD-UP OVER SET psig 10% 20% 30% 40% 50% 10% 20% 30% 40% 50% NR NR 5
6 TABLE 6 WATER CAPACITY IN GPM S.G. = 1.0 T = 60 F L = All Sizes - Composition Diaphragm Only OUTLET (psig) ATM 5 SETPOINT (psig) ALL BODY SIZES % BUILD 10% 20% 30% 40% 50% HI VEL HI VEL CAV CAV CAV CAV CAV CAV CAV CAV CAV 75 HI VEL HI VEL HI VEL HI VEL HI VEL 100 HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL CAV CAV HI VEL CAV CAV CAV 75 HI VEL HI VEL 7410 HI VEL HI VEL 100 HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL CAV CAV HI VEL HI VEL HI VEL HI VEL HI VEL 100 HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL CAV 75 HI VEL HI VEL HI VEL HI VEL HI VEL 100 HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL HI VEL CAV CAV HI VEL CAV CAV CAV HI VEL HI VEL HI VEL HI VEL NOTE: Where "HI P1" is indicated, the pressure build exceeds established limits in Technical Bulletin. Where CAV is indicated, the fl ow has reached choked fl ow, full cavitation. 6
7 TABLE 7 AIR CAPACITY - SCFH S.G. = 1.0 T = 60 F L = All Sizes - Composition Diaphragm Only OUTLET (psig) ATM 5 SETPOINT (psig) ALL BODY SIZES % BUILD 10% 20% 30% 40% 50% HI P1 HI P HI P1 HI P NOTE: HI P1 HI P HI P1 HI P HI P1 HI P1 Where "HI P1" is indicated, the pressure build exceeds established limits in Technical Bulletin. 7
8 DIMENSIONS AND WEIGHTS Shipping Weight All Sizes Lbs. Kg. 8 4 The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifi cations of such product at any time without notice. Cashco, Inc. does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Cashco, Inc. product remains solely with the purchaser. 8
9 MODEL BQ PRODUCT R 12/05/14 POS POS POS POS POS POS POS POS POS POS & A An X in POS 12 followed by a 5-digit control num ber over rides remaining selections. Basic (Above -20 F(-29 C)) Desig. POSITION 6 & 7 - TRIM DESIGNATION NUMBERS BRZ POSITION 2 - GASKET * & SERVICE Service Gaskets Options Brass Trim Body Material DI Non-Oxygen Std: Graphite / NBR B Primarily for Oxygen TFE -45 D Cryogenic -325 to +100 F All TFE -5 & -36** C (-198 to 38 C) *Refer to Tech Bulletin for temperature limits. **Cryo Const. includes Special Cleaning #S-1134 (Opt.-55). CS Desig. Stainless Steel Trim DI Body Material CS SST B0* B0 B0 B0 S0 S0 S0 S0 B1 B1 B1 B1 S1** S1 S1 S1 B2 B2 B2 B2 S3 S3 S3 S3 B3 B3 B3 S3N SC SC SC B4 B4 B4 S5 S5 S5 S5 B5* B5 B5 S9 S9 S9 S9 B6 B6 B6 S36 ** BB BB BB BB S Inlet POSITION 3 - SIZE Size Outlet 1/4" DN8 1/2" DN15 2 3/8" DN10 1/2" DN15 3 1/2" DN15 1/2" DN15 4 POSITION 11 - RANGE SPRING POSITION 5 - BODY & SP. CHAMBER MATERIALS Body/Sp. Ch. DI/DI 1 BRZ/DI 2 BRZ/BRZ* 3 CS/SST 6 SST/SST ** A *Utilize w/cryo Opt-5 **Utilize w/cryo Opt-36 Standard Cryogenic (OPT-5 & -36) Steel Range Spring SST Range Spring psig Barg psig (Barg) 5-15 ( ) ( ) A ( ) ( ) B ( ) ( ) C ( ) ( ) D ( ) ( ) F S40M 4M 4M * Trim utilized w/cryo Opt-5 ** Trim utilized w/cryo Opt-36 S40T 4T 4T SB SB SB SB POSITION 12 - TRIM OPTIONS Description Option For Special Construction Contact Cashco for Special Product Code SPQ X POSITION 13 - FEATURE OPTIONS Description Option CI Closing Cap CI or CS Spring Chamber. (Included with "1+6" Variation) Differential Const. w/closing Cap on DI or SST Spring Chamber POSITION 14 - SPRING CHAMBER OPTIONS Description Option 1/4" NPT Vent Tap. -25 E SST Rain-proof Bug Vent (Includes Opt-25). -25S H POSITION 16 - CERTIFICATE OPTIONS Description Option Special Cleaning: Per Cashco Spec #S BRZ or SST body/sp.ch. mat'ls only. Suitable for oxygen service. (Not Available w/ "1+6" Variation). -55 M Special Cleaning: Per Cashco Spec #S N POSITION 17 - PAINT OPTIONS Description Option Epoxy Painted Per Cashco Spec #S W Epoxy Painted Per Cashco Spec #S-1687 OFFSHORE Applic. -95OS Y Cashco, Inc. P.O. Box 6 Ellsworth, KS PH (785) Fax. # (785) sales@cashco.com Printed in U.S.A. Cashco GmbH Handwerkerstrasse Hoppegarten, Germany PH Fax. No germany@cashco.com Cashco do Brasil, Ltda. Al.Venus, 340 Indaiatuba - Sao Paulo, Brazil PH Fax. No. brazil@cashco.com
MODEL HP-1+6+S HP-S-DIFF-TB 03-16 TECHNICAL BULLETIN "HIGH" PRESSURE DIFFERENTIAL REDUCING REGULATOR CAUTION FEATURES
TECHNICAL BULLETIN HP-S-DIFF-TB 03-16 ISO Registered Company MODEL HP-1+6+S "HIGH" PRESSURE DIFFERENTIAL REDUCING REGULATOR Model HP-1+6+S is a heavy duty, high pressure reducing differential regulator.
289 Series Spring-Loaded Relief Valves
October 14 89 Series Spring-Loaded Relief Valves W187_1 W1871 TYPE 89L 1 NPT TYPES 89H AND 89HH W187 NPT TYPE 89H W187_ TYPES 89U AND 89A Figure 1. Types 89H, 89L and 89U Relief Valves Introduction The
Baumann 24003 3 Way Bronze or Stainless Steel Control Valve
Product Bulletin D1039X012 24003 Valve Baumann 24003 3 Way Bronze or Stainless Steel Control Valve 3 Way Rugged Industrial Control Valve For Mixing and Diverting Applications The Baumann 24003 3 way control
PRESSURE REDUCING CONTROL VALVE
Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING CONTROL VALVE with LOW FLOW BY-PASS FEATURE Main Line
1805 Series Relief Valves
October 2011 1805 Series Relief Valves P1026 1805G Type 1805-2 Type 1805-4 Figure 1. Typical 1805 Relief Valves Introduction The 1805 Series relief valves are designed for use in farm tap applications
Mustang Series PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE. M115-2 (Globe) M1115-2 (Angle) Schematic. Standard Components
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Throttles to maintain minimum upstream pressure PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE
Types 66R and 66RR Low-Pressure Relief Valves
November 2009 Types 66R and 66RR Low-Pressure Relief Valves W1953 W1908 TYPE 66R RELIEF VALVE TYPE 66RR RELIEF VALVE Figure 1. Typical Constructions Introduction Types 66R and 66RR low-pressure throttling
1301 Series High-Pressure Regulators
1301 Series High-Pressure Regulators Bulletin 71.1:1301 December 2013 P10 Figure 1. Type 1301F Regulator Features Durable Stainless Steel Diaphragm For high-outlet pressure applications. Spare Valve Disk
API Flanged Safety Relief Valves Series 526 CATALOG
API Flanged Safety Relief Valves Series 26 CATALOG The-Safety-Valve.com 1 Valve finder How to find the right product group High operating to set pressure ratio, high backpressure or low total height? Yes
S GATE KNIFE GATE VALVE WITH PNEUMATIC ACTUATOR
MAIN FEATURES The pneumatic S GATE knife gate valve is intended for the automatic shut off of pipes of the heavy fluids like slurries and powders. The main fields of application are the water treatment,
Baumann 81000 Mikroseal Control Valve
Product Bulletin D103340X012 Baumann 81000 Mikroseal Control Valve The Baumann 81000 Mikroseal control valve (figures 1 and 2) is excellent for throttling of liquid or gaseous media, particularly where
Non-Code Liquid Relief, ASME Section VIII, Air/Gas and Steam, National Board Certified, Safety and Relief Valves
Non-Code Liquid Relief, ASME Section VIII, Air/Gas and Steam, National Board Certified, Safety and Relief Valves Features Top guided design offers high capacity with 0.110 in 2 [0.710 cm 2 ] orifice area.
61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve
61W - Wafer style resilient seated butterfly valve 61L - Lugged style resilient seated butterfly valve Features Rounded polished disc edge gives full concentric sealing, lower torques, longer seat life
Baumann 87000 Flexsleev Sanitary Control Valve
Product Bulletin D103345X012 Baumann 87000 Flexsleev Sanitary Control Valve The Baumann 87000 control valve (figures 1 and 2) is excellent for throttling high purity liquid or gaseous media commonly found
Pilot Operated Pressure Reducing Valve PRV 47 (Steel) PRV47I (St.Steel)
OPTIONS: USE: AVAILABLE MODELS: Pilot Operated Pressure Reducing Valve PRV 47 (Steel) PRV47I (St.Steel) DESCRIPTION The ADCA PRV47 pilot operated pressure reducing valves are designed for use on steam,
167D Series Switching Valves
June 2011 167D Series Switching Valves P1185 P1184 167D TWO-WAY SWITCHING VALVE 167DA THREE-WAY SWITCHING VALVE Figure 1. 167D Series Switching Valves Introduction The 167D Series switching valves are
RUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a wafer valve designed for a wide range of industrial applications. The double-seated design provides bi-directional shut off. The design of the valve
Air Eliminators and Combination Air Eliminators Strainers
Description Air Eliminators and Combination Air Eliminator Strainers are designed to provide separation, elimination and prevention of air in piping systems for a variety of installations and conditions.
SLAM-SHUT VALVE. Type OSE. Europe, Middle East, Africa and Asia Pacific Documents Only. Process Management TM
SLAM-SHUT VALVE Type OSE Process Management TM DESCRIPTION The purpose of the OSE slam shut valve is to totally and rapidly cut off gas flow when the outlet pressure exceeds or drops below the setting.
REGULATORS D& HD Series
Watson McDaniel reserves the right to change the designs and/or materials of its products out notice. 2002 Watson McDaniel Company Ductile Iron body - HD Series Full port strainer & blowdown valve on pilot
REGULATORS 175/153 Series
175/153 Series 175 HEATING 153 COOLING Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2002 Watson McDaniel Company Revised 7/2002 175 / 153 Screwed
08.08 Vic-Check Valves
The check valves are a product of computer-assisted innovative engineering with quality features including a new hydrodynamically efficient profile. The Vic-Check valve utilizes a spring-assisted, single-disc
TECHNICAL DATA. NOTES: For use with Trim Chart on page 27 b. (open fold-out)
De cem ber 6, 1999 Trim 27 a MODEL J-1 ALARM CHECK VALVE VERTICAL TRIM Maximum 250 PSI WWP This Trim Chart is for use with the following Viking Trim Sets Valve Size Standard* Trim P/N Foam System** Trim
1800C and 1800C-HC Series Service Regulators. Technical Bulletin
and -H Series Service Regulators Technical Bulletin and -H Series Service Regulators 0 Elster American Meter The Series pressure regulators are designed to control natural gas, air, nitrogen, carbon dioxide,
V47 Series Temperature Actuated Modulating Water Valves
V47 Series Temperature Actuated Modulating Water Valves Master Catalog 125 Valves, Miscellaneous (Other Than Gas) Section V Product Bulletin V47 Issue Date 0286 Application The V47 modulating valves regulate
Type 92S Pilot-Operated Steam Regulator
Type 92S Pilot-Operated Steam Regulator Introduction The Type 92S steam regulator is piston actuated for high cycle steam service which includes a Type 6492L, 6492H or pilot (see Figure 1). These pilots
5.23.22 STEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD PART 1: GENERAL. 1.01 Purpose:
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
Fisher CV500 Rotary Globe Control Valve
CV500 Valve D101606012 Product Bulletin Fisher CV500 Rotary Globe Control Valve The Fisher CV500 Cam Vee-Ball control valve combines the rangeability of the cammed-segmented V-notched ball, with the inherent
Baumann 24000 Little Scotty Bronze Control Valve
24000 Valve Product Bulletin Baumann 24000 Little Scotty Bronze Control Valve Baumann Little Scotty industrial control valves are intended for general utility service in pressure, flow, and temperature
3/2-way Solenoid Valve, direct-acting, NC or NO
3/2-way Solenoid Valve, direct-acting, NC or NO Electrical connection cable plug, Form A With or without manual override as standard Threaded port and sub-base s Impulse optional Type 6014 can be combined
Installation and Operating Instructions Installation Instructions for SS EPE-316L Series
INSTR3010 0406 Installation and Operating Instructions Installation Instructions for SS EPE-316L Series Congratulations on your purchase of this Aqua-Pure high flow, single housing filtration system. This
RMF Engineering 23 05 23
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
solenoid valves SV Series 2- and 3-way Solenoid Valves for Gas and Liquid
2- and 3-way Solenoid Valves for Gas and Liquid SV10: Vacuum to 3000 psig SV430: Vacuum to 3000 psig SV20: Vacuum to 6000 psig SV460: Vacuum to 6000 psig SV30: Vacuum to 3000 psig Circle Seal Controls
Direct-Operated Pressure & Temperature Regulating Valves
Direct-Operated & Temperature Regulating Valves Direct-Operated are used for controlling pressure or temperature in a variety of applications. Regulating Valves Page No. Cast Iron 3/8 2 Page No. O Series
IF IT FLOWS THE BOWIE PUMP CAN PUMP IT
IF IT FLOWS THE BOWIE PUMP CAN PUMP IT Bowie Industries, Inc. Bowie, TX 76230 USA Page 1 Bowie Pumps Manual General Pump Information..Page 2 300 Series Pumps.. Page 5 400 Series Pumps.Page 11 500 Series
Index 11.1. Page. Pumping Systems...11.2-11.4 Intensifiers...11.5 Gas Boosters...11.6-11.7 High Pressure Generators...11.8-11.9
Pumping Systems, Intensifiers, Gas Boosters and High Pressure Generators High Pressure Equipment Company produces a number of components and systems for general industrial, elevated pressure applications.
DARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
SECTION 15062 STEAM AND CONDENSATE PIPING PART 1 DESIGN DIRECTIVES 1.1 QUALITY ASSURANCE A. Comply with the provisions of the following: 1.2 DESIGN CRITERIA 1. ASME B 31.9 Building Services Piping : for
Type 99 Pressure Reducing Regulator
Instruction Manual Form 589 Type 99 February 2016 Type 99 Pressure Reducing Regulator! WARNINg Since a pilot-operated regulator is constructed of both a pilot and a main valve, care should be used not
MFP14, MFP14S and MFP14SS Automatic Pumps
Page 1 of 6 TI-P136-02 ST Issue 12 Cert. No. LRQ 0963008 ISO 9001, S and SS utomatic Pumps Description The Spirax Sarco automatic pump is a displacement receiver operated by steam or compressed air. It
QLM and QLD Series Three-port Control Valves
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
Type 99 Pressure Reducing Regulator
Bulletin 7: February 2016 Type Pressure Reducing Regulator W27 W76 Figure 1. Typical Type Regulator Introduction The Type gas regulators provide a broad capacity for controlled pressure ranges and capacities
CHEXTER TM FITS YOUR APPLICATION, PROFITABLY
CHEXTER TM FITS YOUR APPLICATION, PROFITABLY Commercial Construction CHEXTER TM Check Valves are economically used in chilled and hot water air conditioning systems, refrigeration and other piping and
TYPE E Main Valve Sizes 3 /8 through 12
SD 3001F PRINTED IN U.S.A. SD 3001F/0707 A B TYPE E MAIN VALVE C D E TYPE E Main Valve Sizes 3 /8 through 12 The Spence Type E Main Valve is of normally closed, single seat design featuring packless construction,
American- Darling 5¼" B-84-B-5.
-5 Sealed Lubrication Chamber Seals operating threads from water and debris which greatly reduces routine maintenance. Top Travel Stop Nut Helps prevent stem buckling and damage to bronze components which
Type EZL Pressure Reducing Regulator for Low Differential Pressure Applications
Type EZL Pressure Reducing Regulator for Low Differential Pressure Applications May 2016 W8962 Figure 1. Type EZL Pressure Reducing Regulator Features Main Diaphragm The main diaphragm is Nitrile (NBR)
Proportional Relief Valves
www.swagelok.com Proportional Relief Valves R Series Liquid or gas service Set pressures from 10 to psig (0.7 to 413 bar) 1/4 and 1/2 in. and 6 to 12 mm end connections 2 Proportional Relief Valves Spring
Shut-off & Lockout Valves 1/4" to 1-1/2" port size
Section 16 Shut-off & Lockout Valves 1/4" to 1-1/2" port size Contents T72 Excelon Shut-off & Lockout Valves 1/4", 3/8" Port Sizes....................................ALE-16-2 T73 Excelon Shut-Off & Lockout
Valves, Automation & Controls. series 84 /99 HIGH PERFORMANCE 3-PIECE BALL VALVE REDUCE & FULL PORT, STANDARD & FIRE SAFE. www.sharpevalves.
Valves, Automation & Controls series 8 /99 & FS8 /FS99 HIGH PERFORMANCE -PIECE BALL VALVE REDUCE & FULL PORT, STANDARD & FIRE SAFE www.sharpevalves.com Design & Features SHARPE VALVES - SERIES 8/99 Fire
TN2000 Series Pneumatic Piston Actuators for DN125 to DN300 SPIRA-TROL Series Control Valves
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
PRESSURE REDUCER AND RELIEF VALVES WITH METALLIC BELLOW FOR WATER STEAM
PRESSURE REDUCER AND RELIEF VALVES WITH METALLIC BELLOW FOR WATER STEAM PRESSURE REDUCER AND RELIEF VALVES These devices are used to reduce and control a gaseous flow pressure (air, steam, gas ). The PRESSURE
CRANE. Σελίδα 1 από 2. Dimensions and Weights. Weight (kg) Size
CRANE Σελίδα από 2 DM93 Variable Orifice Double Regulating Valve PN6 Cast Iron Balancing Valve (VODRV), Flanged to BSEN 92-2 The DM93 variable orifice double regulating valves will give satisfactory performance
Pressure & Flame Protection
Pressure & Flame Protection Safety Relief Valves Safety Relief Valves WB SERIES SPRING LOADED SAFETY RELIEF VALVES The WB is designed safely relieve excess pressure in pumps, pipework, tanks, calorifiers,
OPERATING and MAINTENANCE MANUAL SERIES 2700A CONTROL VALVE CONTENTS. INTRODUCTION...1 Scope...1 Description...1 Valve Identification...
OPERATING and MAINTENANCE MANUAL SERIES 2700A CONTROL VALVE CONTENTS INTRODUCTION...1 Scope...1 Description...1 Valve Identification...2 1.0 VALVE INSTALLATION...2 2.0 VALVE MAINTENANCE...3 Actuator Disassembly...3
Mueller B-101 and A-3 Drilling and Tapping Machines
TM TM Mueller and Drilling and Tapping Machines A guide to selecting Mueller Equipment Mueller TM TM and Drilling and Tapping Machines When it comes to line stopping and drilling and tapping technology
Self-operated Pressure Regulators Universal Pressure Reducing Valve Type 41-23
Self-operated Pressure Regulators Universal Pressure Reducing Valve Type 41-23 Application Pressure regulators for set points from 5 mbar to 28 bar Valves in nominal sizes DN 15 to 100 Nominal pressures
AIR LINE VALVES AND GAUGES
AIR LINE VALVES AND GAUGES INGERSOLL-RAND AIR LINE VALVES AND GAUGES Maintaining consistent air pressure throughout the entire system is crucial for maximum performance and productivity. Ingersoll-Rand
Self-contained valve functions as integral check valve, flow sensing element and bypass control valve.
Self-contained valve functions as integral check valve, flow sensing element and bypass control valve. Features Eliminates high cost of installation and maintenance of complex conventional flow control
Scraper Passage Indicator. Electrical Indicator. Features
IV Scraper Passage Indicator Bulletin No: 5110.001.03 Date: June 2008 Cross Indexing No: n/a Supersedes: 5110.001.02 (1/06) Flag Indicator Electrical Indicator Options Description TDW s IV Scraper Passage
WATER PRESSURE REDUCING VALVES
MADE IN THE USA WATER PRESSURE REDUCING VALVES TABLE OF CONTENTS PRODUCT PAGE How Pressure Reducing Valves Work 3 36 Series 4 36C Series 6 36H Series 8 AUTOMATIC PRESSURE REDUCTION Pressure reducing valves
Type 119 Control Valve
Instruction Manual Form 5204 Type 119 December 2009 Type 119 Control Valve Introduction Scope of the Manual This instruction manual provides installation, spring adjustment, maintenance, and parts information
2-Port Self-acting Temperature Control Valve Selection for Heating and Cooling Applications
Page 1 of 12 TI-S21-07 CH Issue 1 Cert. No. LRQ 0963008 ISO 9001 2-Port Self-acting Temperature Control Valve Selection How to select a system Valve selection: 1. Is the application for heating or cooling?
Specification Data CM37002 09/10. Putting You In Control. 37002 Series MiniTork ll Control Valves. Heavy Duty Control Butterfly Valves
Putting You In Control Specification ata CM37002 09/10 37002 Series MiniTork ll Control Valves Heavy uty Control Butterfly Valves resser Masoneilan 37002 Series MiniTork II Control Valves Heavy uty Control
PLUMBING RE-SUBMITTAL 22 11 17
PLUMBING RE-SUBMITTAL 22 11 17 ACADEMIC BUILDING & PATRIOT S CASA TEXAS A&M UNIVERSITY - SAN ANTONIO, TX NO. 25-3122, VAC NO. 39019 OWNER: ARCHITECT: MEP ENGINEER: GENERAL CONTRACTOR: PLUMBING CONTRACTOR:
TECHNO Multi-Purpose Check Valves for Industry
Multi-Purpose Check Valves for Industry THE SHORT FORM (SF) WAFER IS THE PERFECT DESIGN FOR AIR SERVICE AND LIGHT DUTY LIQUID APPLICATIONS. AVAILABLE IN SIZES 1-72 MALE THREADED ENDS, GROOVED ENDS, PLAIN
Ball Valves (HB Series) Catalog 4121-HB Revised, April 2005
Ball Valves (HB Series) Revised, April 2005 Introduction Parker High Pressure HB4 Series Ball Valves provide reliable shut-off or switching functions. The upper and lower trunnion bearings enhance the
VAD. Variable Area Desuperheaters
Desuperheater overview Steam used in process plants can be superheated, that is, heated to a temperature above saturation. The excess of temperature above its saturation is called 'superheat'. Desuperheated
Spira-trol TM Two-port Control Valves EN Standard KE, KF and KL DN15 to DN300 and ASME Standard KEA, KFA and KLA ½" to 12"
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
VALVES FOR REFRIGERATING SYSTEMS
VALVES FOR REFRIGERATING SYSTEMS FROM QUALITY OUR NATURAL DEVELOPMENT Achieved the goal of fi fty years working in the industry of Refrigeration and Air Conditioning, Castel Quality Range of Products is
% ^ ) 0.55 W Low Power Solenoid Valves Aluminum, Brass, or Stainless Steel Bodies 1/4" to 1" NPT. 2/2 3/2 4/2 5/2 5/3 SERIES Low Power
.55 W Solenoid Valves Aluminum, Brass, or Stainless Steel Bodies /" to " NPT / 3/ / 5/ 5/3 Features Molded one-piece solenoid with highly efficient solenoid cartridge and.55 W low wattage coil Standard
Best Under Pressure 2900 MPV. Pilot-Operated Safety Relief Valve. www.dresser.com. 2900 MPV Oct 2008-CO
Best Under Pressure 0 MPV PilotOperated Safety Relief Valve www.dresser.com 0 MPV Oct 2008CO 0 MPV 0 Pilot Operated Relief Valve Consolidated offers a unique pilot valve design that combines p performance,
Product Manual. CVS Type 67AFR Filter Regulator. Introduction. Installation. Description
Product Manual CVS Type 67AFR Filter Regulator Introduction This CVS Controls product manual includes instructions for the installation, adjustment, maintenance and parts ordering of the CVS Type 67AFR
Pressure and Temperature Controls
Pressure and Controls Pressure Reducing Armstrong pressure reducing valves (PRVs) and temperature regulators help you manage steam, air and liquid systems safely and efficiently. And assure uninterrupted
Morrison Bros. Co. General Product Specifications
Morrison Bros. Co. General Product Specifications Tank Mounted Spillbox The spill containment device is manufactured to contain spills and drips that may occur at the fill point on aboveground storage
BWX SERIES BUTTERFLY VALVE FOR CRYOGENIC APPLICATIONS
BWX SERIES BUTTERFLY VALVE FOR CRYOGENIC APPLICATIONS The BWX series butterfly valve has been especially designed for use in cryogenic applications with high quality CrNi steel. Testing of the valve includes
Veriflo Pressure Regulators
Hydraulik - Pneumatik Steffen Haupt Moritzer Straße 35 01589 Riesa Telefon: 03525 6801-0 Telefax: 03525 680120 info@haupt-hydraulik.de Veriflo Pressure Regulators 4511 November 2003 KATALOG Vertrieb: Frau
AMERICAN Mechanical Joint Pipe For Water, Sewage or Other Liquids
AMERICAN Mechanical Joint Pipe For Water, Sewage or Other Liquids The AMERICAN Mechanical Joint was developed by the American Cast Iron Pipe Company and first marketed in 1929. Since that time, millions
ball valves Flomite 71 Series 2-way Integral Panel Mount Ball Valves
2-way Integral Panel Mount Ball Valves Used for quick on-off service with a visual indication of flow, HOKE s 2-way ball valves offer orifice sizes up to 0.25 (6.4mm). Flomite valves feature a floating
Hose Clamps & Fittings
All Stainless Steel Marine or Underground Hose Clamps 5/16 HEX HEAD SCREW 60000 SERIES Highly corrosion resistant Use for marine or underground applications Stainless Steel Band, Housing Plated Steel Screw
Wafer, Semi-Lug, Lug and Double Flanged Type
Wafer, Semi-Lug, Lug and Double Flanged Type Page 1 www.globalvalvecenter.com 2011 Description The centric replaceable liner butterfly valve is capable of bi-directional flow and bubble tight shut-off
HOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). The special design of the
Stainless Steel Single and Dual Circulation Kits
Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating
Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation
Instruction Manual 1052 Size 20 Actuator (F & G) Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Contents Introduction... 1 Scope of manual... 1 Description... 1 Specifications...
SERIES ASM NEOPRENE/EPMD FLANGED SINGLE SPHERE CONNECTOR CONNECTORS. Pressures to 225 PSIG (15.51 barg) Temperatures to 230ºF (110ºC)
APPLICATIONS Process Industry Weak Acids Alkalies Compressed Air Pulp & Paper MODELS ASM - Flanged Connection OPTIONS Control Rods Oil & Gas Water & Waste Pump suction & discharge Sea water Chemical lines
An SPX Process Equipment Operation. Universal II Industrial Series Rotary Positive Displacement ECP Pumps
An SPX Process Equipment Operation Universal II Industrial Series Rotary Positive Displacement ECP Pumps New levels of performance. Reduced operational and maintenance costs. For more than half a century,
Stainless Steel Valves For the Sanitary Industries
www.swagelok.com Stainless Steel Valves For the Sanitary Industries Sanitary ball valves Manual and pneumatically actuated butterfly valves Disk and ball check valves ir blow check valves ir relief valves
WD600 STEAM TRAPS. Thermodynamic Steam Trap
WD600 Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company WD600, WD600L Sizes 3/8, 1/2, 3/4, 1 NPT Material Stainless
700 Series Safety Relief Valves
Assistance: Our experienced and fully trained team of Technical Sales Engineers and distributors are available to give advice and assistance on the sizing and selection of the Bailey 700 Series and any
BURSTCHECK LINE OF RUPTURE DISC BURST INDICATORS
BURSTCHECK LINE OF RUPTURE DISC BURST INDICATORS INTRODUCTION Rupture discs are often used as primary pressure relief devices and to isolate pressure relief valves. When used as a primary pressure relief
Pipe Valves, Fittings and Nipples Pressures to 15,200 psi
Pipe Valves, Fittings and Nipples MAXIMATOR has been designing and manufacturing high pressure equipment for more than thirty years and has a worldwide reputation for quality and reliability, backed by
Fisher 2625, 2625SST, and 2625NS Volume Boosters
Instruction Manual 2625, 2625SST, and 2625NS Volume Booster Fisher 2625, 2625SST, and 2625NS Volume Boosters Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Educational
AIR-AIR PRESSURE MULTIPLIER (BOOSTER)
AIR-AIR PRESSURE MULTIPLIER (BOOSTER) The air-air pressure multiplier, or booster, is an automatic device that compresses air to give an outlet pressure that is double the inlet pressure. It is normally
EZR Series Pressure Reducing Regulator
EZR Series Pressure Reducing Regulator November 2015 Robust Quiet Operation Thoroughly Tested Exceptional Design W7399 TYPE EZR REGULATOR Internally Actuated W8136 TYPE EZROSX WITH INTEGRAL SLAM-SHUT DEVICE
GS-General Service Control Valves
GS-General Service Control Valves GS-General Service Valves The GS-General Service Valves continue Copes-Vulcan s tradition of designing and manufacturing control valves that provide both exceptional service
Series 830. Direct Acting Steam PRV. Typical Installation. Selection. Other Series 800 Steam Regulators. Series 810 PRV
Series 8 Direct Acting Series 8 Direct Acting Other Series 8 Regulators Typical Installation Series 8 supply Series 82 Series 8 Safety ale Strainer Series 8 PRV ondensate Series 8 uced Direct Acting PRV
MAKING MODERN LIVING POSSIBLE. Thermostatic valve AVTA. Technical brochure
MAKING MODERN LIVING POSSIBLE Thermostatic valve AVTA Technical brochure 2 IC.PD.500.A3.02-520B3728 Danfoss A/S 07-2009/ RA-MC/mr Contents Page Features............................................................................................4
Fisher 377 Trip Valve
377 Trip Valve Product Bulletin Fisher 377 Trip Valve Fisher 377 pressure sensing trip valves are for control applications where a specific valve/actuator action is required when supply pressure falls
Solenoid valves 2/2-way direct-operated Type EV210A
Solenoid valves 2/2-way direct-operated Type EV210A Features EV210A NC and NO Very compact valves for industrial application, such as control and dosage For water, oil, compressed air and similar neutral
APCO SLOW CLOSING AIR/VACUUM VALVES
BULLETIN 1 JULY 01 APCO SLOW CLOSING AIR/VACUUM VALVES Series 1900 APCO Slow Closing Air/Vacuum s Maximum Air Flow Velocity in Good Pipeline Design The Air/Vacuum operates in the normal fashion allowing
HIGH STANDARD VALVES FOR NON-STANDARD CONDITIONS.
HIGH STANDARD VALVES FOR NON-STANDARD CONDITIONS. ZWICK: MANUFACTURER OF HIGH STANDARD TRIPLE OFFSET VALVES. 100% ZERO-LEAKAGE 100% MADE IN GERMANY 100% QUALITY Zwick is a leading manufacturer of valves
ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.
ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.4-1998 - Cast Iron Threaded Fittings ASME/ANSI B16.5-1996 - Pipe