OLIMEX MSP430-PROGRAMMER SOFTWARE INSTALLATION

Size: px

Start display at page:

Download "OLIMEX MSP430-PROGRAMMER SOFTWARE INSTALLATION"

Harry Parrish
7 years ago
Views:

1 Note: This was written for step by step on Windows XP; some screens may appear different if you are using another OS. Before using your Olimex JTag Programmer for the first time you will need to upload new firmware files provided by Stanley to the Programmer. This requires you to have the software installed. Installing the Software: Step 1: Download the software from the link below Software: OLIMEX MSP430-PROGRAMMERPROGRAMMER - GUI _CLI _DLL / freeware - stand alone software which allows you to program MSP430 devices Step 2: After clicking on the link to download the software click open. Step 3: Open MSPProg_Setup.exe

This requires you to have the software installed.

2 Step 4: Extract all files Step 5: Click Next

3 Step 6: Click Next Step 7: Make sure Show extracted files is checked then hit finish

4 Step 8: Open MSPProg_Setup Step 9: Click Run

5 Step 10: Click I Agree Step 11: Note the destination folder you are saving to (defualt should be C:\Olimex\MSP430 Programmer) --- Click Next

$C:\Olimex\MSP430 Programmer) ---$

6 Step 12: Click Install Step 13: Click Yes

7 Step 14: Click Next Step 15: Click Close

8 Next you have to add the 3 dll and 1 ini files provided by Stanley into the Olimex directory and update the firmware in the Olimex Jtag Programmer Step 16: Navigate back to the destination you picked in step 11 above

9 Step 17: Move the Stanley dll and ini files to the destination found in the step above ***NOTE: You will get an error when moving these files if you have the MSP430 Programmer application open. If it is open close it before moving the files to this location.*** Step 18: Depending on your operating system it may ask you if you would like to keep the old files and rename the new files, you do NOT want to keep the old files- picked the option that allows you to replace the old files with the new Stanley files. You would just click Yes to All in the screen shot below:

*** Step 18: Depending on your operating system it may ask you if you would like to keep the old files and rename the new files, you do NOT

10 Step 19: Download the drivers from the link below (also found on Drivers: Windows drivers + MSP430-JTAG-ISO-MK2 firmware version Step 20: Click Save Step 21: In the drop down navigate to the destination you picked in step 11 and click Save

com) Drivers: Windows drivers + MSP430-JTAG-ISO-MK2 firmware

11 Step 22: Click open folder Step 23: Right click on the folder OLIMEX_MSP430-DLL_drivers.zip and extract all.

12 Step 24: Click Next Step 25: Click Next

13 Step 26: Uncheck Show extracted files and click Finished Step 27: Navigate to the destination you picked in step 11 and find and open USBXpressInstaller.exe

14 Step 28: Click Install

15 Next you will need to update the firmware in your programmer Step 29: If your Jtag Programmer is not already plugged in via USB then make that connection now. NOTE: You will also want to have your programmer plugged into daughter card and the daughter should be plugged into an EL Lockset. If these connections are not made you will get an error Cannont Connect to Device Step 30: Hardware Wizard Should pop up once you plug in your device; select yes, this time only and click next Step 31: Select Install the software from a list or specific location and then click Next

NOTE: You will also want to have your programmer plugged into daughter card and the daughter should be plugged into an EL Lockset.

16 Step 32: Click Browse Step 33: Browse to the file location of your drivers and click OK once you have the file selected

17 Step 34: Click Next

18 ***This should load your drivers if it doesn t you may have missed a step.*** Step 35: Looking at your programmer screen make sure the arrow is pointing to Debugger Step 36: Press the right arrow on the JTag Programmer and you will see a screen that looks similar to this: Step 37: Open Olimex MSP Programmer

pointing to Debugger Step 36: Press the right arrow on the JTag Programmer

19 Step 38: Find MSP430F5340 in the drop down list and select it

20 Step 39: Uncheck all data memory boxes and the one READ box next to program memory also CHECK SpyBiWire Box (see green arrows). Leave everything else at default. Step 40: Click Blank Check within the MSP Programmer application (see green arrow)

arrows). Leave everything else at default.

21 Step 41: You will see the following screen if it says NOT blank on both Program and Data memory then the new JTag device has the new firmware uploaded. --- Click OK Now see Programming Firmware into your EL Lock

Mini Amazing Box 4.6.1.1 Update for Windows XP with Microsoft Service Pack 2

Mini Amazing Box 4.6.1.1 Update for Windows XP with Microsoft Service Pack 2 Below you will find extensive instructions on how to update your Amazing Box software and converter box USB driver for operating