SAFETY RECOMMENDATION

Transcription

1 TEKDEK LED Luminaire for Parking Garages 1 TD17 SERIES IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: SAFETY RECOMMENDATION SAFETY RECOMMENDATION THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS. DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE. SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS. SAVE THESE INSTRUCTIONS A 1/16" diameter aircraft cable with end-loop (not included) is recommended for A 1/16" diameter cable attaching with the end-loop fixture structural (not included) to the upper is recommended structural. for attaching the fi xture structural to the upper structural AIRCRAFT CABLE ATTACH TO UPPER STRUCTURAL 1/16" DIA. AIRCRAFT CABLE (SUPPLIED BY OTHERS) SCREW (SUPPLIED BY OTHERS) F-460_090314

2 DIRECT TO SURFACE INSTALLATION 1: Remove tertiary lens (if provided) by unscrewing (4) captive screws. : Remove heatsinking/led base by unscrewing (4) captive screws. These will be the inner most screws. 3: Disconnect the quick connector wires from the LED board and the driver. 4: Make electrical connection to J-box (for sizes, see next page). Circuit wire connection must be in J-box. Install housing to surface using (4) 5/16" diameter mounting holes. 5: Re-assemble by reversing the removal procedure. QUICK CONNECT HOUSING DRIVER HEATSINK/LED BASE HOUSING TOP VIEW CAPTIVE SCREWS (4) FOR REMOVING HEATSINK CAPTIVE SCREWS (4) 5/16 MOUNTING HOLES (4) TERTIARY LENS (IF PROVIDED) F-460_090314

3 QUICK MOUNT KIT INSTALLATION 1: Quick mount plate fastens to a secure J-box. Screws by others. : Align hanger bracket with center slot on top of fi xture as shown at right. Fixture can then hang from bracket while electrical connections are made. 1. LOCKING HOOKS HANGER BRACKET QUICK MOUNT PLATE 3: After excess wires are in J-box (see sizes below), push the fi xture up to the mounting plate. Locking hooks should slide through slots. Twist fi xture until a click is felt or heard. Fixture is now in place. USED WITH THE FOLLOWING JUNCTION BOX SIZES: 4" ROUND 4" SQUARE 3-1/" OCTAGON ALIGN HANGER BRACKET WITH CENTER SLOT 3. LOCKING HOOK SLOTS F-458_010714

4 BIRD GUARD INSTALLATION DIRECT TO SURFACE & QUICK MOUNT No tools required. Must install before fi xture is mounted. 1. Fasten tab through slots as shown above.. Bird Guard lays inside of casting. F-4557_041013

5 PENDANT MOUNT INSTALLATION SWIVEL MOUNT NOT RECOMMENDED (Kenall does not supply counterbalance system) 1: Attach 3/4" threaded conduit to housing (provided by others). : Make electrical connections in conduit body (supplied by others). CONDUIT BODY AND CONDUIT (BY OTHERS) HOUSING TAPPED FOR 3/4 NPS THREAD MUST USE SEALANT OR SEALING LOCKNUT F-459_041013

6 TRUNNION KIT INSTALLATION 1: Attach housing plate to housing. Align notch. Use (4) fl at head screws (provided). TRUNNION BRACKETS : Assemble trunninon kits as shown using (4) ¼-0.500" screws and nuts (provided). 3: Attach trunnion brackets to housing plate with (4) " hex head screws (provided). CONDUIT BODY AND CONDUIT (BY OTHERS) (To increase depth, move this fastner here) 4: Make electrical connections in conduit body (supplied by others). NOTE: Top of bracket to top of the fi xture measurements: 9.1" min; 14.6" max HOUSING PLATE MUST USE SEALANT OR SEALING LOCKNUT HOUSING F-457_041013

7 TEKDEK LED Luminaire for Parking Garages 1 TD17 SERIES IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS. DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE. SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS. SAVE THESE INSTRUCTIONS BIRD GUARD INSTALLATION - PENDANT MOUNT & TRUNNION KIT 1. Bird Guard lays on top of casting. (For Trunnion Kit remove tabs) Pendant Mount. Attach both sides with (4) screws provided. NOTE: For LEL option, align hole in bird guard with LED indicator Trunnion Kit F-4558_041013

8 MOUNT FIXTURE WITH REGARDS TO OPTICAL ALIGNMENT KEY DIRECTION TYPES II, III, IV DRIVING LANE 3 TYPE V, NORMAL TYPE V, SQUARE DRIVING LANE TYPE II LIGHT DISTRIBUTION PATTERN TYPES TYPE III TYPE IV TYPE V NORMAL TYPE V SQUARE KEY OPTICAL ALIGNMENT KEY F-457_041013

9 CUSTOMER SERVICE For technical assistance, call KENALL ( ). 9 WARRANTY This limited warranty is provided by Kenall (the Seller) to you (the Purchaser)as original purchaser of the LED lighting product. This limited warranty may be transferred to subsequent purchasers of the product as long as it is in its original packaging. Qualifying Kenall LED products shall be warranted by Kenall, for a period of ten (10) years from the date of manufacture, to be free of defects in workmanship, materials, LED lamps and internal power regulation components against defects that result in an excessive lumen depreciation, as defined by L70 Luminaire Lifetime (L70) or when at least 10% of the discrete LED sources fail to illuminate. L70 shall be defined as 70% of the published warranty luminous flux at time of manufacture using IESNA LM testing methods. Click here for full warranty information. Kenall reserves the right to issue credit, repair, or replace the defective merchandise, at its discretion, upon notification and confirmation by its local representative of the defect. Kenall also reserves the right to test and examine the defective product if the defect is questionable and to deny the warranty herein for any product altered, improperly installed, installed in applications for which it is not intended. This includes operation in ambient temperatures above stated limits for any length of time. Failure by electrical surge shall not be covered under warranty. Kenall assumes no responsibility for labor or freight costs incurred in connection with the installation, removal, or replacement of products determined to be defective or any other consequential or incidental damages arising from the use of the product. Kenall s entire liability on any claim of loss or damage resulting from a defective product is limited to the replacement price of the product. F-457_041013