DC Isolation Strapping Guide
|
|
- Amberlynn Casey
- 3 years ago
- Views:
From this document you will learn the answers to the following questions:
What type of goggles are used?
What is the clamps on the rails checked for?
What do you need to do before going to the strapping location?
Transcription
1 DC Isolation Strapping Guide
2 This guide Flame retardant overalls Electrical gauntlets Safety goggles Dry towel First aid kit Mobile phone Safe System of Work (SSOW) pack Wire brush Short Circuit Bar Short Circuit Straps Live Line Tester, Proving Unit and spare battery Non-conductive paddle for removal of ballast Bag to carry equipment MANDATORY EQUIPMENT LIST
3 STRAPPING TEAM PRE-START CHECKS As the COSS, confirm that you have received and verified the SSOW Pack a minimum of one shift before work starts (pack to include strap layout diagram). Check that you have the required equipment and PPE to undertake your role. Check that all the equipment is in good condition. Before going to the strapping location you must receive a face to face briefing from the Engineering Supervisor (ES).
4 5 Check that you know where the strapping access point is and where the strapping points are relative to the access point. If not sure ask the ES to show you. DO NOT START WORK WITHOUT THE ABOVE ITEMS BEING IN PLACE PRE-START CHECKS
5 BEFORE PLACING STRAPS 1 2 Check that the SSOW covers from the access point to the strapping location. Use the following to confirm that you are in the correct location: a. Access point signage b. SSOW pack (principal source of information) c. Sectional Appendix and Track diagrams d. Mileage posts and chainage markers e. Use a smartphone app (such as Omnicom) but only as a check (remember GPS is not always accurate).
6 Before going on or near the line Confirm you have been briefed. 1 STEP
7 STEP 2 Check the condition of your PPE and equipment.
8 Check you are wearing the correct PPE (gauntlets, safety goggles, safety helmet, safety boots and flame retardant overalls). 3 STEP
9 STEP 4 Using a wire brush, clean the underside of the two running rails where the clamps are to be fixed.
10 Fix strap to running rail FURTHEST from conductor rail and tighten securely. 5 STEP
11 6 STEP Fix strap to running rail CLOSEST to conductor rail and tighten securely.
12 Before testing the conductor rail check the Live Line Tester is working correctly using the Proving Unit. 7 STEP
13 2nd Test that the 8 1st conductor rail is NOT live using the Live Line Tester. (Immediately check the Live Line Tester on the Proving Unit again afterwards). STEP
14 Insert the Short Circuiting Bar, shout a warning and swiftly push down to apply (stand with your back to the conductor rail and look away). 9 STEP
15 STEP 10 With the Short Circuiting Bar still in position, wire brush the underside of the conductor rail.
16 With the Short Circuiting Bar still in position, push strap under the running rail and conductor rail and secure tightly to the conductor rail. 11 STEP
17 STEP 12 Check that all clamps are secured tightly and that the strap is not creating a trip hazard. Remove the Short Circuiting Bar, pick up the equipment and exit the site using SSOW.
18 Network Rail Electrical Control Room (ECR) Brighton Canterbury Eastleigh Lewisham Paddock Wood Raynes Park Selhurst IPS IMPORTANT CONTACT NUMBERS
19 IPS IMPORTANT CONTACT NUMBERS Network Rail Route Control Kent Sussex Wessex Network Rail NSC 24/7 Operational Close Call, incident or accident reporting
20 WORKING RESPONSIBLY DRIVING WORKING AT HEIGHT Always be sure the required plans and permits are in place before you start a job, or go on or near the line. Always use the equipment that is fit for its intended purpose. Never undertake any job unless you have been trained and assessed as competent. Never work or drive while under the influence of drugs or alcohol. Never use a handheld or hands-free phone, or programme any other mobile device, while driving. Always obey the speed limit and wear a seat belt. WORKING WITH ELECTRICITY Always test before applying earths or straps. Never assume equipment is isolated always test before touch. Always use a safety harness when working at height, unless other protection is in place. WORKING WITH MOVING EQUIPMENT Never enter the agreed exclusion zone, unless directed to by the person in charge. LIFESAVING RULES
GHD EPCM Standard operating procedure Working at height May 2013 v1
GHD EPCM Standard operating procedure Working at height May 2013 v1 Table of contents 1. Purpose 2. Scope 3. Duty of care 4. Lifesaving rules; An overview 5. Roles and responsibilities 4.1 Operating centre
More informationUser Installation Guide
Careline Alarm User Installation Guide 1.1 IMPORTANT INFORMATION The user s telephone MUST BE connected to the Reach TEL socket - a double adapter on the incoming line must not be used. If the user has
More informationSOP Prehospital Scene Management SOP Prehospital Clinical Care SOP Prehospital (HEMS) Missions Activation Dr Alastair Newton Dr Cieran McKiernan
Emergency Medical Retrieval Service (EMRS) www.emrs.scot.nhs.uk Standard Operating Procedure Title Version 1 Related Documents Author Reviewer Safety at Scene SOP Prehospital Scene Management SOP Prehospital
More informationZAPPY 3 OWNER S MANUAL. Read this manual completely before riding your Electric ZAPPY 3.
ZAPPY 3 OWNER S MANUAL Read this manual completely before riding your Electric ZAPPY 3. TECHNICAL INFORMATION Model No. : ZAPPY 3 Product size Type of motor Motor power Battery type Battery Charger Charging
More informationInstallation Instructions for Alarm Module Kit A043F059
Instruction Sheet 07-2013 Installation Instructions for Alarm Module Kit A043F059 1 Introduction The information contained within is based on information available at the time of going to print. In line
More informationWORKPLACE INDUCTION FOR CONSTRUCTION WORKPLACES INFORMATION SHEET 1
WORKPLACE INDUCTION FOR CONSTRUCTION WORKPLACES INFORMATION SHEET 1 Overview This Information Sheet provides advice for persons conducting a business or undertaking (PCBUs) including builders and principal
More informationFLUORESCENT UV- RING LIGHT OPERATING INSTRUCTION
FLUORESCENT UV- RING LIGHT OPERATING INSTRUCTION Caution! UV-radiation of this device is in the range of UV-A (320-400 nm). Direct exposure to eyes shall therefore be avoided. UV protection glasses shall
More informationBest Methods for Safe Hipot Testing
Best Methods for Safe Hipot Testing When working with electrical safety test equipment, instruments that output potentially dangerous voltages and currents, it is always important to regular review and
More informationSchkopau Site Requirements. Version 2: July 2009 www.shell.com/chemicals/transport
Schkopau Site Requirements Version 2: July 2009 www.shell.com/chemicals/transport 1. Name of Installation: Werk Schkopau* See also General Requirements 2. Physical address of location DOW Europe GmbH C/o
More informationMETHOD STATEMENT INSTALLATION OF INSULATING FLANGE KITS
METHOD STATEMENT INSTALLATION OF INSULATING FLANGE KITS Revision Date Prepared By Approved By Method Statement IF Kits BAC Corrosion Control Limited Stafford Park 11 Telford TF3 3AY Tel: 01952 290321 Fax:
More informationReach. Touch USER GUIDE. At-Home Alarm Unit. Personal Pendant. www.tynetec.co.uk
Reach At-Home Alarm Unit Touch Personal Pendant USER GUE www.tynetec.co.uk . PORTANT NFORATON The users telephone UST BE connected to the Reach TEL socket a double adapter on the incoming line must not
More informationCHECKING AND TESTING ELECTRICAL INSTALLING WORK
CHECKING AND TESTING ELECTRICAL INSTALLING WORK Department of Consumer and Employment Protection Energy Safety Preface It is a requirement of the Electricity (Licensing) Regulations 1991 that all electrical
More informationCurtain Guards Made of PVC and designed to protect the operator from the risk of airborne chips or tool fragments.
Two General Safety Rule for CNC Machines Never operate a CNC machine without proper training or consulting the specific operator's manual for that particular machine and control type. Never attempt to
More informationSERVICE GUIDE For WARN PULLZALL 120v AC &100v AC P/N 685000 & 685001
SERVICE GUIDE For WARN PULLZALL 120v AC &100v AC P/N 685000 & 685001 REPAIR / REPLACEMENT INSTRUCTIONS TROUBLE SHOOTING GUIDE 986765A2.doc Page 1 of 50 WARNING This guide identifies potential hazards and
More informationParallel Circuits Charles Lang
SCIENCE EXPERIMENTS ON FILE Revised Edition 6.20-1 Parallel Circuits Charles Lang Topic Parallel circuits Time 1 1 2 hours! Safety Adult supervision is required. Please click on the safety icon to view
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationSafety and Construction Requirements for Pre 1978 Schedules K, T&C and CR. Part One. Part Two
Section Seven - Schedule AA Safety and Construction Requirements for Pre 1978 Schedules K, T&C and CR. Contents Part One Article 1 Article 2 Article 3 Article 4 Article 5 Article 6 Article 7 Article 8
More informationCaboose Too Rear Seat Instruction Manual 0090X & 0091X Series
Caboose Too Rear Seat Instruction Manual 0090X & 0091X Series Joovy 2919 Canton Street Dallas, TX 75226 (877) 456-5049 Fax: (214) 761-1774 Email: customerservice@joovy.com Web Site: www.joovy.com ! WARNING
More informationQUALIFICATION HANDBOOK
QUALIFICATION HANDBOOK Level 2 and 3 NVQ Certificate in Rail Engineering Traction and Rolling Stock (7597-05/10) September 2011 Version 1.1 (September 2011) Qualification at a glance Subject area Rail
More informationTeam Skills Challenge Event # 1 Plant Layout Score Sheet
Team Skills Challenge Event # 1 Plant Layout Score Sheet State Name: Team Members: 1. 2. 3. 4. Placement of Plant Material 25 Deduct 5 points/plant not placed within 6 inches +/- of correct placement to
More informationGuide to GOOD WSH PRACTICES PICTOGRAMS
Guide to GOOD WSH PRACTICES PICTOGRAMS ~ Table of Contents Introduction 2 Purpose of Pictograms 2 Dimensions of Materials 3 Colours 4 Installation Information 5 Annex 6 Introduction The aim of this publication
More informationSchool of Engineering University of Glasgow
School of Engineering University of Glasgow Electronics Workshops Rankine Building 319A (2 Technicians) 510 (1 Technician) 712A (4 Technicians, 1 Modern Apprentice) James Watt South 619 (2 Technicians)
More informationPOP Pushchair. Instructions
POP Pushchair Instructions Important: Keep for future reference Please read these instructions carefully before using your new pushchair Keep them in a safe place so that you may use them in the future
More informationLife Saving Rules. Working Safely at EPCOR
Life Saving Rules Working Safely at EPCOR 1 Our Health and Safety Beliefs We believe: All incidents are preventable. HSE is integral to our work and the way we conduct business. HSE is serious and a shared
More informationRevision Date Reviewed By Authorised By. A 31/01/14 R McKeen P FitzPatrick Review Date 31/01/15 Change Details No Change Task
Safe Working Procedure: TAT SWP 014 v1 Lifting and Placing Stanchions and stanchion bases Revision Date Reviewed By Authorised By A 31/01/14 R McKeen P FitzPatrick Review Date 31/01/15 Change Details No
More informationReplacing an AC Power Cord in a Power Shelf
Replacing an AC Power Cord in a Power Shelf No system shutdown is required to replace one AC power cord in a power shelf. All components in the enclosure continue to receive power from the other power
More information2016 Evolocity High Schools competition Technical regulations
2016 Evolocity High Schools competition Technical regulations (Amended gratefully from Greenpower F24 regulations, UK) MULTI (3 + )WHEELED VEHICLES All vehicles are subject to scrutineering and compete
More information7 FUNCTION DIGITAL MULTIMETER
7 FUNCTION DIGITAL MULTIMETER 90899 OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All rights
More informationTaipei European School Bus Charter
Taipei European School Bus Charter This document outlines the operational parameters of Taipei European School s bus transportation service. Appendix 1 sets out key rules and regulations relating to passenger
More informationSecure Them for Life. Child safety seats. From infant seats to seat belts, everything you need to know to ensure your child s safety.
Secure Them for Life Child safety seats From infant seats to seat belts, everything you need to know to ensure your child s safety. It s the law In a vehicle, children whose sitting height is less than
More informationCisco Unified IP Conference Phone 8831 Installation
Cisco Unified IP Conference Phone 8831 Installation Cisco Unified IP Conference Phone 8831 Installation Overview, page 1 Before You Begin, page 1 Cisco Unified IP Conference Phone 8831 Components, page
More informationThe Black Box Push Button Control Box
Roll Rite, LLC and its entire staff would like to not only Thank You but congratulate you on your purchase of one of what we feel to be the finest line of tarping systems in the industry. The Black Box
More informationSite Induction Presentation
ABC Contracting Site Induction Presentation This presentation provides a mock site induction and serves to help those people in the process of preparing and delivering site inductions It is essential that
More informationFIREFIGHTER SAFETY. Stay safe during substation fires
FIREFIGHTER SAFETY Stay safe during substation fires FIREFIGHTERS AND SUBSTATIONS Electrical substations reduce the high voltages used to move electricity over long distances to the lower voltages that
More informationSeven function digital multimeter
Seven function digital multimeter 98025 Set up And Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com
More information32-421 Eskom Life Saving Rules 39-47 Implementation of the Eskom Life Saving Rules
32-421 Eskom Life Saving Rules 39-47 Implementation of the Eskom Life Saving Rules LIFE SAVING RULES WHY DO WE HAVE THEM? Life Saving Rules are Non-negotiable Rules All Eskom Employees, Agents, Consultants,
More information2001-2005 Fuel Pickup Kit Installation Guide
2001-2005 Fuel Pickup Kit Installation Guide 2001-2005 Fuel Pickup Kit Installation Guide PPE offers super tanks that are easy to install and fit perfectly beneath your vehicle without compromising clearance
More informationBATTERY CHARGING HARNESS (THREE-PIN)
-J090 REV. 009-0- BATTERY CHARGING HARNESS (THREE-PIN) GENERAL Kit Number 9-9B Models This Three-Pin Battery Charging Harness fits all Harley-Davidson motorcycles equipped with a volt battery, and allows
More informationReference Title Created Owner Review 09.11.2012. Reviewed 11/12
1 Driving at Work Policy May 2012 Reference Title Created Owner Review HSWO- Driving at work Policy 09.11.2012 Reviewed 11/12 Health, Safety and Wellbeing Office HSWO/MR 11.05.2015 2 University of Sussex
More informationCHILD BOOSTER SEAT. Instructions for Installation & Use Series No. 4050/A/2013 IMPORTANT: KEEP THIS BOOK IN THE PLACE PROVIDED ON THE CHILD RESTRAINT
CHILD BOOSTER SEAT Instructions for Installation & Use Series No. 4050/A/2013 IMPORTANT: KEEP THIS BOOK IN THE PLACE PROVIDED ON THE CHILD RESTRAINT INDEX PAGE 3 4 6 7 9 10 14 19 21 22 INTRODUCTION WARNINGS
More informationWiMo Antennen und Elektronik GmbH Am Gäxwald 14, D-76863 Herxheim Tel. (07276) 96680 FAX 9668-11
The I-PRO Traveller part no. 11440 Thank you for your purchase, please take your time to digest some of the important building tips and the essential matching/adjustment techniques. You will need 8m of
More informationRutherford County Safety Training. Walking Surface Safety
Rutherford County Safety Training Walking Surface Safety Course Outline Objectives Become familiar with and with Walking Surfaces in your workplace Know how to reduce the risk by applying Walking Surface
More informationAdditional information: -OSHA Instruction CPL 2.103, Field Inspection Reference Manual, Chapter IV, Section A -29 CFR 1910, Subpart I, Appendix B
1 Additional information: -OSHA Instruction CPL 2.103, Field Inspection Reference Manual, Chapter IV, Section A -29 CFR 1910, Subpart I, Appendix B -1910.1000(e) 2 1910.132(h) 72 FR 64341, Nov. 15, 2007
More informationDiscussion Leaders Guide Session Slips, Trips and Falls
Discussion Leaders Guide Session Slips, Trips and Falls 1. Preparation You will need a DVD player and a television. Review the Tell, Ask and Review portions of the Discussion Leaders Guide. You will be
More informationUsing and Wiring Light Emitting Diodes (LEDs) for Model Railroads
Using and Wiring Light Emitting Diodes (LEDs) for Model Railroads LEDs have many useful applications in Model railroading, including: Locomotive headlights Rear-end warning lights for cabooses and passenger
More informationUsing a Pendulum to Measure Gravity s Acceleration Elizabeth B. Chesick
SCIENCE EXPERIMENTS ON FILE Revised Edition 6.33-1 Using a Pendulum to Measure Gravity s Acceleration Elizabeth B. Chesick Topic Motion of a pendulum; gravity Time 1 2 hour! Safety Please click on the
More informationCHAPTER 2 GENERAL SAFETY REQUIREMENTS
Bridge Inspection Handbook 2-1 2.1 INTRODUCTION CHAPTER 2 GENERAL SAFETY REQUIREMENTS Safety is everyone's business. As an employer, MassDOT is obligated to promote job safety and furnish safe tools, equipment,
More information15GAL STEEL OIL DRAIN WITH 110V PUMP
15GAL STEEL OIL DRAIN WITH 110V PUMP OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationPractical accident assistance
Practical accident assistance A guideline for Mercedes-Benz customers Please note: Changes may have been made to the products since this brochure went to press (12/2009). This brochure has been compiled
More informationDUBOX TM LOOSE PIECE HAND TOOL
DUBOX TM LOOSE PIECE HAND TOOL Hand Tool Part Number HT-2234 22-30 AWG For termination Of Dubox TM 76357-x01LF Terminals FCI MANUAL P/N 10123594-9090 Issued: Date (12/20/2012) Page 1 of 9 HT-2234 HAND
More informationBooster Seat. OWNER'S MANUAL Model 8481. 2001 Graco 420-5-01
Booster Seat OWNER'S MANUAL Model 8481 Even if using this booster seat seems easy to figure out on your own, it is very important to read this manual. Your child s safety depends on you installing and
More informationClass 5 to 7 Truck and Bus Hydraulic Brake System
Class 5 to 7 Truck and Bus Hydraulic Brake System Diagnostic Guide 1st Edition * 5+0 Important Service tes The information in this publication was current at the time of printing. The information presented
More informationAccidents/Incidents are Preventable
Section 4 Fundamentals of Accident/Incident Prevention Accidents/Incidents are Preventable Many people believe that accidents are the inevitable result of unchangeable circumstances, fate, or a matter
More informationDTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual
DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR Installation and Operation Manual 1 ENGLISH Safety Instructions 2 Features 2-3 Specifications 3 Installation 4-5 Wiring Diagrams 6-7 Warranty 8
More informationSELECTION, APPLICATION AND MAINTENANCE
DIESEL PROTECTION SYSTEMS Automatic Diesel Engine Shut Down System for Safe Area Applications SELECTION, APPLICATION AND MAINTENANCE Series 300 Series 310 SYSTEM DESCRIPTION Suitable for attended engine
More informationUser Guide. Model 380260 Insulation Tester / Megohmmeter
User Guide Model 380260 Insulation Tester / Megohmmeter Introduction Congratulations on your purchase of Extech s Insulation Tester/Megohmmeter. The Model 380260 provides three test ranges plus continuity
More informationRepairing the Seam of the WaterRower Tank
Repairing the Seam of the WaterRower Tank The following instructions are for repairing a WaterRower that is leaking water around the seam, the 1 overlap between the top and bottom halves of the tank. While
More informationWorking Safely on Substations
A practical guide to Working Safely on Substations W.S. ON SUBSTATIONS.indd 1 6/12/07 12:03:36 A practical guide to Working Safely on Substations National Grid Eakring Technical Training Centre Kirklington
More informationSafe Driver. Information Sheet
Workplace Transport Safety Safe Driver Information Sheet To effectively control workplace transport risks, the vehicle, the driver and the working environment must be appropriately managed. This information
More informationELECTRIC BICYCLE USER MANUAL
ELECTRIC BICYCLE USER MANUAL 1 Main Technical Parameters and Specification Weight: 23 kg Wheel size: 20 Maximum speed: 25 km/h E BIKE URBAN Range: Up to 45km (with pedal assist) Type: lithium Voltage:
More informationReplacing the Gateway M320 Keyboard
Replacing the Gateway M320 Keyboard This package includes a replacement keyboard for your Gateway M320 notebook and these printed instructions. Tools you need You need a small Phillips and a small flat-blade
More informationThermo Top - Troubleshooting Tree
Thermo Top - Troubleshooting Tree 07-15-2002 CAUTION Troubleshooting requires comprehensive knowledge about the structure and theory of operation of the Thermo Top heater. Troubleshooting and repairs may
More informationBSH Exhibition Sample Risk Assessment for exhibitors / contractors
BSH Exhibition Sample Risk Assessment for exhibitors / BSH Conferences Ltd have produced this risk assessment for its exhibitors to use as a template if they have not undertaken risk assessment before.
More informationLockout/Tagout Training Program
Lockout/Tagout Training Program (Student Handouts) Name Date This page intentionally left blank. Notes page: 2 Notes page: 3 Sample Written Program for Control of Hazardous Energy (Lockout/Tagout) 4 1910.147
More informationINSTALLATION GUIDELINES for SOLAR PHOTOVOLTAIC SYSTEMS 1
City of Cotati Building Division 201 W. Sierra Ave. Cotati, CA 94931 707 665-3637 Fax 792-4604 INSTALLATION GUIDELINES for SOLAR PHOTOVOLTAIC SYSTEMS 1 Any PV system on a new structures should be included
More informationRecord Cleaning Machine
Record Cleaning Machine Owner s Manual UK December 2010 Photo 1 Photo 2 IMPORTANT! READ THIS OWNER S MANUAL CAREFULLY, BEFORE USING THE MACHINE! Introduction You are now the proud owner of an Okki Nokki
More informationUNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS
UNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS CONTENTS Parts List... 2 Parts Diagram... 2 Helpful Hints... 3 Installation... 4 Operation and Troubleshooting Guide... 6 Warranty Information... 8 Form #3132,
More informationSAFETY SIGNAGE PROCEDURE
Page 1 of 10 SAFETY SIGNAGE PROCEDURE 1.0 PURPOSE 1.1 To enable a reference to signage to meet legislative requirements and ensure in cases of emergency appropriate signage is visible. 2.0 SCOPE 2.1 This
More informationModel Safety Plan. Why Do You Need A Safety Plan?
Model Safety Plan Best Safety Practices for YOUR Business Model Valet Services Program The primary intent of this document is to provide you with guidance developing, establishing, or improving your own
More informationFALLING OBJECTS EXCESSIVE NOISE CHAINSAW & CHIPPER WORK AT HEIGHTS MANUAL HANDLING
JOB NO: PROJECT: DATE: SWMS NO: SWMS 001.1 PREPARED BY: Ian Hartley REVISED BY: Nick Bragg & Cameron McNeil ACTIVITY: TREE REMOVAL & PRUNING SIGNED BY: REVISION DATE: December 2015 MINIMUM PERSONAL PROTECTIVE
More informationGM DURAMAX LMM 09-10 Fuel Pickup Kit Installation Guide
Pacific Performance Engineering, Inc. www.ppediesel.com GM DURAMAX LMM 09-10 Fuel Pickup Kit Installation Guide Technical Support (714) 985-4825 Rev: 3/30/11 v5 DISCLAIMER OF LIABILITY This agreement sets
More informationKing Edward VI School Southampton. Canoeing and Kayaking Generic Risk Assessment
King Edward VI School Southampton Canoeing and Kayaking Generic Risk Assessment January 2012 Reviewed & updated by ECW Kayaking & Canoeing: Generic Risk Assessment Hazards arising from Outdoor Kayaking
More informationBelt Sander. Given a properly adjusted belt sander, accessories, instruction and demonstration of use, each student will be able to:
I. Competencies Belt Sander Given a properly adjusted belt sander, accessories, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the belt sander. B. Pass
More informationElectrical Safety in the Workplace
Electrical Safety in the Workplace NFPA 70 E Presented by Sabine Mueller What Made Sabine Choose Such a DRY Topic? Ulterior Motive Metso Mueller Engineering has been visiting many scrap yards two or more
More informationPEDAL CAR - GO CART ASSEMBLY & OPERATING INSTRUCTIONS
PEDAL CAR - GO CART 42822 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2000 by Harbor Freight Tools. All
More informationXenon HID Lighting System
Automotive Safety Systems User Installation Manual Preface Specifications Thank you for purchasing NOVABLUE Xenon H.I.D. (High Intensity Discharge) vehicle lighting systems. Before installing this product,
More informationChainsaw Training and Certification Program
I. Purpose and Need Chainsaw Training and Certification Program employees perform a variety of jobs requiring the use of chainsaws. Among these are firefighting, timber stand improvement, road maintenance,
More informationHP SATA/SAS hard drive and Solid State Drive installation
HP SATA/SAS hard drive and Solid State Drive installation This document describes how to install Serial ATA (SATA) and Serial Attached SCSI (SAS) hard drives or Solid State Drives (SSD) in an internal
More informationTraditional Sonar and DSI Sonar Installation
Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and installing the unit on
More information2. Remove rear cover of head lamp if bulbs are covered/sealed within the housings, and remove halogen bulb carefully.
These instructions are designed to address most general installation procedures across vehicles and should not be considered vehicle make, model or year specific. Please contact the vendor directly for
More informationElgin Fire Department
Breathing Operations Elgin Fire Department Safety - Respiratory Protection Program - Self Contained Apparatus (SCBA) Policy # 2024.01 Issued: 09/08/06 Subject: Purpose: Scope: Self Contained Breathing
More informationChapter 22: Electric motors and electromagnetic induction
Chapter 22: Electric motors and electromagnetic induction The motor effect movement from electricity When a current is passed through a wire placed in a magnetic field a force is produced which acts on
More informationNotes. Material 1. Tools the employee is expected to operate
OSHA Standard29 CFR 1910.211-.247, Subpart O, Machinery and Machine Guarding, and Subpart P, Hand and Portable-Powered Tools and other Hand- Held Equipment. Hand Tool Safety Preparation 1. Read Applicable
More informationFlat Bottom Long Ram Hydraulic Jack
Flat Bottom Long Ram Hydraulic Jack 3 Ton 8 Ton 36468 36469 ASSEMBLY & OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOUS
More informationVELA Samba 400/410/500/510/520/530 USER MANUAL VARIANT: Manual no. 105563. VELA Samba 530. VELA Samba 510. VELA Samba 520.
USER MANUAL Samba UK VARIANT: 400/410/500/510/520/530 Manual no. 105563 Samba 530 Samba 510 Samba 520 Samba 410 Samba 400 GAS Samba 500 TABLE OF CONTENT 1.0. INTRODUCTION 3 1.1. SAFETY 4 1.2. WARRANTY
More informationElkhorn Construction, Inc. Safety Manual Title: Fall Protection Policy Effective Date: 03-01-2000
1. General Requirements (OSHA References: OSHA 29 CFR 1926.503) 1.1 Elkhorn Construction, Inc. employee-owners and subcontractors are required to use fall protection equipment or systems when an assessment
More informationTREX SELECT RAILING Installation Instructions
TREX SELECT RAILING NOTE: All Trex Select Railing lengths are manufactured at ON CENTER dimensions (spanning from center of each post): 67-5/8" (76.8 cm) for 6' (.83 m) on center, and 9-5/8" (35.3 cm)
More informationReachout Lock Replacement for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors
for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors Thank you for choosing Andersen. For questions call 1-888-888-7020. For more information
More informationHandbook 16. Handbook 16. AC electrified lines. GE/RT8000/HB16 Rule Book
GE/RT8000/HB16 Rule Book Uncontrolled When Printed Handbook 16 AC electrified lines Handbook 16 Issue 3 September 2015 Comes into force 05 December 2015 This handbook is for those personnel who need to
More informationTremline Pty Ltd trading as The Hills Bark Blower
JSA No: Rev: 10011 Date: 10010 ABN 1 07 880 6 Website: wwwbarkblowercomau Job Number Start Time: Vehicle : Max Length Hose Date: Company Name: Product: Quantities Depth Job site address: Description of
More informationCircuit Electrical Testing
Safe Isolation Procedure Circuit Electrical Testing Site Safety Management It is essential from the outset that effective management and control of the system, apparatus and equipment used on site is achieved
More informationRISK RATING SAFE WORK METHOD STATEMENT 1 HIGH 2 MEDIUM 3LOW. I approve the use of this Safe Work Method Statement: NAME: POSITION: Department Manager
RISK RATING 1 HIGH 2 MEDIUM 3LOW SAFE WORK METHOD STATEMENT Title: : Working at Height above 2trs Ref No: 1 I approve the use of this Safe Work Method Statement: NAME: POSITION: Department Manager SIGNATURE:
More informationRecommended Guidelines for the Safe Use of Tools & Equipment at Height
Recommended Guidelines for the Safe Use of Tools & Equipment at Height DROPS GLOBAL e: admin@dropsonline.org t : +44 (0)1224 861811 f: +44 (0)1224 861812 w: www.dropsonline.org Published by DROPS (Dropped
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More information"Engineered to Ride, Built to Last "
Congratulations on your purchase of an Arnott air suspension product. We at Arnott Incorporated are proud to offer a high quality product at the industry s most competitive pricing. Thank you for your
More information3/4 PIPE CLAMP WITH STAND
3/4 PIPE CLAMP WITH STAND Model 94053 ASSEMBLY AND OPERATING INSTRUCTIONS (3/4 DIAMETER PIPE NOT INCLUDED.) 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More informationBattery Backup Sump Pump System
Battery Backup Sump Pump System Instruction Manual Battery Operated SUMP TEST Push to Test System RESET Push to Silence Pump Alarm Warning BATTERY FUSE WATER POWER What to do Terminals corroded or battery
More informationSBC90. Abrasive Blast Cabinet Assembly & Operating Instructions
SBC90 Abrasive Blast Cabinet Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important
More informationTemporary Worker Safety Checklist
Temporary Worker Safety Checklist The following checklists provide guidance for staffing agencies and employers that hire temporary workers regarding the steps each party should take to ensure it is meeting
More information