Meter Test-Socket Adapter

Size: px

Start display at page:

Download "Meter Test-Socket Adapter"

Percival McGee
7 years ago
Views:

1 Introduction There are different test-socket adapters for the Form 5 and Form 9 SEL-734 and SEL-735 meters. The kit numbers needed for ordering are listed below. Installation SEL-734 and SEL-735 Form 5 Standard ( ) Form 9 Standard ( ) SEL-735 Form 5 EXM ( ) Form 9 EXM ( ) Standard Form 5 and Form 9 Meters Connect an SEL-735 (or SEL-734) meter to your Form 5 or Form 9 test set using one of the adapters listed below. The adapter is purposed for testing only and should only be used indoors. Form 5 Standard ( ) Form 9 Standard ( ) Please use the following steps to connect the socket adapter to the SEL-735 or SEL-734 meter and test set. Step 1. Ensure the circuit is safe. Step 2. Connect the current ring terminals from the socket adapter to the Slot Z, Terminals Z01 Z06 on the back of the SEL-734 or SEL-735 meter. Step 3. Tighten the connections. Step 4. Plug the voltage connector from the socket adapter into the SEL-735 Slot Z, Terminals Z07 Z10 (or SEL-734 Slot E, Terminals E01 E04). Step 5. Tighten the connector. Step 6. Plug the socket adapter into the test set Form 5 or Form 9 socket. Step 7. Ensure all connections are mechanically and electrically sound. Step 8. Energize the test set and the SEL meter. SEL-735 EXM Connect an SEL-735 EXM meter to your Form 5 or Form 9 test set using one of the following socket adapters. The socket adapter is purposed for testing only and should only be used indoors. Form 5 EXM ( ) Form 9 EXM ( )

SEL-734) meter to your Form 5 or Form 9 test set using one of the adapters listed below. The adapter is purposed for testing only and should only be used indoors.

2 2 Please use the following steps to install the socket adapter to the SEL-735 meter and test set. Step 1. Ensure the circuit is safe. Step 2. Plug the self-shorting CT connector from the socket adapter into the CT connector connected to the SEL-735. Step 3. Tighten the connector. Step 4. Plug the barrel connector from the socket adapter into the barrel connector connected to the SEL-735. Step 5. Tighten the connector. Step 6. Plug the socket adapter into the test set Form 5 or Form 9 socket. Step 7. Ensure all connections are mechanically and electrically sound. Step 8. Energize the test set and SEL-735. Figure 1 shows the Form 5 standard and EXM socket adapters. Form 9 socket adapters and are similar to adapters and , but have a Form 9 configuration. Please refer to Specification on page 3 for the actual wiring configuration of your socket adapter. Form 5 Standard ( ) Figure 1 Form 5 EXM ( ) Equipment Needed Small flat screwdriver (Standard meters only)

Plug the barrel connector from the socket adapter into the barrel connector connected to the SEL-735. Step 5. Tighten the connector. Step 6.

3 Specification 3 Figure 2 and Figure 3 show the adapter electrical connections. Please ensure the ratings are not exceeded. Form 5 Standard Meter Adapter ( ) #10 RING TERMINALS Form 9 Standard Meter Adapter ( ) VB VB VB Figure 2 #10 RING TERMINALS Standard Mechanical Drawings

Form 5 Standard Meter Adapter (915900256) #10 RING TERMINALS Form 9

4 4 SEL-735 EXM Form 5 Adapter ( ) J1 C5683 CONNECTOR PIN J1-34 J1-36 J1-37 J1-37 CT SHORTING CONNECTOR (FRONT VIEW) SEL-735 EXM Form 9 Adapter ( ) J1 VB VB CONNECTOR PIN J1-34 J1-35 J1-36 J1-37 CT SHORTING CONNECTOR (FRONT VIEW) Figure 3 SEL-735 EXM Mechanical Drawings

9 Adapter (915900259) J1 VB VB CONNECTOR PIN J1-34 J1-35 J1-36 J1-37

5 Factory Assistance 5 We appreciate your interest in SEL products and services. If you have questions or comments, please contact us at: Schweitzer Engineering Laboratories, Inc NE Hopkins Court Pullman, WA USA Phone: Fax: Internet: info@selinc.com

Laboratories, Inc. 2350 NE Hopkins Court Pullman, WA 99163-5603 USA Phone: +1.

6 6 Notes! WARNING Operator safety may be impaired if the device is used in a manner not specified by SEL.! AVERTISSEMENT La sécurité de l opérateur peut être compromise si l appareil est utilisé d une façon non indiquée par SEL by Schweitzer Engineering Laboratories, Inc. All rights reserved. All brand or product names appearing in this document are the trademark or registered trademark of their respective holders. No SEL trademarks may be used without written permission. SEL products appearing in this document may be covered by U.S. and Foreign patents. Schweitzer Engineering Laboratories, Inc. reserves all rights and benefits afforded under federal and international copyright and patent laws in its products, including without limitation software, firmware, and documentation. The information in this document is provided for informational use only and is subject to change without notice. Schweitzer Engineering Laboratories, Inc. has approved only the English language document. This product is covered by the standard SEL 10-year warranty. For warranty details, visit or contact your customer service representative. SCHWEITZER ENGINEERING LABORATORIES 2350 NE Hopkins Court Pullman, WA USA Phone: Fax: Internet: info@selinc.com *PLS00071*

CoolWave r 2 Phase Control Board and Cable Replacement Kits

Instruction Sheet P/N 1102452A CoolWave r 2 Phase Control Board and Cable Replacement Kits Two kits are available to replace the CoolWave 2 phase control board: S S Phase Control Board and Cable Kit (required