OMX-RS232 Control Interface

Transcription

1 GAFIK Systems Control Interface omx-rs Description Integrates GAFIK 000/6000/7000 Systems with a touchscreen or other digital equipment that supports S communication. Provides S monitoring commands that allow a touchscreen to query GAFIK Systems to: Determine which scene is selected. Keep track of buttons pressed. Provides S control commands that allow a touchscreen to operate GAFIK Systems to: Select or sequence lighting scenes. aise or Lower one or more zones. Lock lighting controls. Activate panic mode (lights go to full on). Functionality is setup via the GAFIK System Processor Panel. May be custom configured for other functions.

2 GAFIK Systems Specifications omx-rs Power Low-voltage Class (PELV). Operating Voltage: V Direct Current. Basic S Command Set Monitoring: Scene selection and scene status updates. Control: Scene selection, scene lockout, sequencing, zone lockout, zone raise/lower. System Communications and Capacity Low-voltage Class (PELV) wiring connects Interface to Processor Panel. Multiple may be used. 0 ft. (m) maximum from Interface to PC or other S source. Environment -0 F (0-0 C). elative humidity less than 90% non-condensing. Functions Function Zone Lock etain Scene Lock etain Sequence etain Sequencing Scene ange Multiple Addresses Button Feedback Scene Status When Activated If power goes out, locked zones stay locked when power returns. If power goes out, locked scenes stay locked when power returns. If power goes out, sequencing resumes when power returns. Sequencing loops through scenes to 6. DIP Switches - used to set address, not function. Interface reports Control Unit and Wallstation button presses. Interface reports scene changes. When Otherwise Power cycling unlocks locked zones. Power cycling unlocks locked scenes. Power cycling stops sequencing. Sequencing loops through scenes to. DIP Switches - operate as specified above. No reporting on button presses. No reporting on scene changes.

3 GAFIK Systems Dimensions omx-rs Front Side COOPESBUG, PA 806 GX-S S INTEF ACE AUXILIA Y CONTOL For use with Lutron GAFIK Eye 000 and 000 products only. CLASS /SELV SWITCH FUNCTION DESCIPTION ZONE LOCK ETAIN ZONE LOCKED UNITS WILL EMAIN IN ZONE LOCK AFTE A POWE OUT AGE 6 SCENE LOCK ETAIN SEQUENCE ETAIN SEQUENCE TYPE FIXED ADDESS AW FEEDBACK SCENE LOCKED UNITS WILL EMAIN IN SCENE LOCK AFTE A POWE OUT AGE SEQUENCING UNITS WILL AGAIN SEQUENCE AFTE A POWE OUT AGE ON: SEQUENCE SCENES -6 OFF: SEQUENCE SCENES - ON: DIPSWITCHES - FO ADDESSING OFF: ONLY ONE INTEFACE PE LINK INTEF ACE WILL EPO T WHEN A BUTTON HAS BEEN PUSHED O ELEASED ON A GAFIK EYE MAIN UNIT O ACCESSOY 7 / (97mm) 7 SCENE ST ATUS 8 TIMECLOCK GAFIK Eye 000 Series INTEF ACE WILL ETUN THE CUENT SCENE OF ALL MAIN UNITS WHEN A NEW SCENE IS SELECTED PC O A/V EQUIPMENT DIP Switches Neutral HOT/LIVE SSA Zone Zone Zone CU WIE ONL Y Class xd DT +V DT -V Ground Screw Link FO WIING OF 000 SEIES, EFE TO INST ALLATION INSTUCTIONS LED LED V TO GAFIK EYE POWE INPUTS: (+V): (+V): S LINK TO PC O A/V EQUIPMENT (000 SEIES) (000 SEIES) IN OUT S LINK TX Data LED (LED ) S Link (to PC or A/V Equipment Class (PELV) Wiring 6 (7mm) / (8mm) Mounting Mount on a " (0.mm) square junction box. May also mount directly to the wall. Ensure that the metal casing is grounded. Connect a ground wire to the ground screw. Note that wires do not feed through the back of the unit. x Junction Box Wall Wall Insert Wires Through Punch-Outs

4 GAFIK Systems S Link Wiring omx-rs Use cable provided. Standard 9-pin serial connector plugs into S equipment, other end connects to S Link terminals. Must be 0 ft. (m) or less. S Signals Link Terminal Signal Typical PC or A/V Equipment Pin on 9-pin Cable Common Data In Data Out No Connect No Connect Com xd Low-Voltage Class (PELV) Wiring Daisy-chain the Interface to the Class (PELV) Wallstation Link that connects to the Processor Panel. Make daisy-chain connections to the low-voltage Class (PELV) Link terminals on the front of Interface. Do not use T-taps. un all wires in and out of terminal block. Each terminal accepts up to two #8 AWG (.0mm ) wires. LED lights when the Class (PELV) link is installed correctly. Consult Processor Panel Specification Submittal for more details. Lutron Cable GX-CBL-6L 0 ft. (m) Maximum To Processor Panel xd PC or AV Equipment Link S Link Wiring Terminals To additional Wallstations/.

5 GAFIK Systems Class (PELV) Terminal Connections omx-rs Two # AWG (.mm ) conductors for common (terminal ) and VDC (terminal ). These will not fit in terminals. Connect as shown. One shielded, twisted pair #8 AWG (.0mm ) for data link (terminals and ). Connect Drain/Shield as shown. Do not connect to Ground (Earth) or Wallstation/. Connect the bare drain wires and cut off the outside shield. Data Link - () twisted, shielded pair #8 AWG (.0mm ) : : D: Drain/Shield () # AWG (.mm ) () # AWG (.mm ) () #8 AWG (.0mm ) () #8 AWG (.0mm ) Class /PELV Control wiring : Common : VDC LED LED V TO GAFIK EYE TO PC O A/V EQUIPMENT POWE INPUTS: (+V): (000 SEIES) (+V): (000 SEIES) IN OUT S LINK