Contact Center CC-165 INSTALLATION & USER'S GUIDE

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Contact Center CC-165 INSTALLATION & USER'S GUIDE"

Transcription

1 Contact Center CC-165 INSTALLATION & USER'S GUIDE

2 Table of Contents Introduction... 2 Specifications... 2 J4 Host Communications... 2 J5 and J12 (upper board)... 3 J6, J13, and 14 Input Connections... 3 Monitor Points... 3 Go Off-line / On-line Command... 4 Shunt Times... 4 J7 & J15 Output Relays... 4 Output Points... 4 Pulsing... 5 J7 Output Relays 0 and J15 Output Relays 2, 3 & J8 Power Connection... 5 S1, S2, and Degraded mode... 6 Troubleshooting Techniques... 6 Tech Tip 1 Verify Communication Between CC-165 and IC Tech Tip 2 Verify Communication Between IC-1600 and Server... 6 Tech Tip 3 Find the Device # of the CC-165 (For Access Gold only)... 7 Tech Tip 4 Replace a Comm20RX chip... 7 Page 1 Copyright 2009, Access Specialties International, LLC, All Rights Reserved

3 INTRODUCTION The CC-165 Contact Center provides remote monitoring for up to 16 contact points, and remote control capability for up to 5 output points. It interfaces with the Access Gold and ASI 2000 software and electrical devices in the field. The CC-165 will continuously monitor the open or closed state of the input and output points, and report changes in condition to the host system. Each input and output has an LED indicator, which will light when an input contact is closed, or an output relay is energized. Mounted in a standard electrical enclosure, the CC-165 is protected from the elements and can be easily stored in high ceilings or wiring closets. Through the software there are several types of commands that can be issued to the CC Immediate, conditional response, re-occurring or scheduled, and one-time future commands all may be issued to give you more flexibility and control over your facility. Locations without card readers may be locked and unlocked manually or at a pre-set time. A sound alarm could be controlled by an output relay of a CC-165 and triggered by an input from the same CC-165. This is known as a Conditional Response. Parking lot lights may be automatically turned on and off at certain times of the day. There are many more ways in which the CC-165 can be used to facilitate building management. SPECIFICATIONS Size 8" x 8" x 4" Power Requirements Hz 1A, or 12 VDC at 1 A 16 Monitored Contact Points 5 Controlled Output Points Operating Temperature -40 C to +75 C J4 HOST COMMUNICATIONS J4 provides the connections for communications to the IC-1600 panel or a Channel Expander (CE-1600). A Channel Expander multiplexes one channel on an IC-1600 into an additional 16 ports and can be placed up to 2 miles away from the IC Removable terminal blocks are provided for easy installation. The CC-165 requires a 4-wire connection to the host. The cable should be 22 gauge, shielded cable, consisting of 2 twisted pair, and all shields earth grounded at one end. Page 2 Copyright 2009, Access Specialties International, LLC, All Rights Reserved

4 The maximum allowed distance from the CC-165 from the IC-1600 or CE-1600 is 2 miles. Note: The greater the distance, the greater the delay in transfer of data between the CC- 165 and the IC Host (a channel or port) J4 CC-165 Lower Board Data + Pin #1 Data Pin #2 Enable + Pin #3 Enable Pin #4 J5 AND J12 (UPPER BOARD) The CC-165 has two ports that are not used, J5 and J12. However, these ports put out both 5 VDC and 12 VDC that can be used to power external devices such as motion detectors, smoke detectors, etc. J5 and J12 provide the following connections for any type of device: Miscellaneous Device J5 J12 5 VDC Pin #1 Pin #1 12 VDC* Pin #2 Pin #2 Ground Pin #3 Pin #3 Note: the board is misprinted at 20VDC J6, J13, AND 14 INPUT CONNECTIONS Monitor Points Sixteen contact monitoring points are available. The contact inputs are current sensitive, not voltage sensitive. An open contact will have 12 VDC across it. A closed point will have approximately 10mA of current. Unlike the Reader Interfaces, the CC-165 does not provide the dedicated inputs (tamper, exit-push button, and DOD). All inputs must be defined as monitor points in the software. The definition of CC-165 is under System Devices of the Access Gold application and under the Device Center for ASI All monitor points have an LED indicator that will emit light when the input contacts are closed. Any of the monitor points can be tied to alarms and conditional responses in the software. Page 3 Copyright 2009, Access Specialties International, LLC, All Rights Reserved

5 Go Off-line / On-line Command The Go Online or Go Offline is the only type of command that can be issued for the inputs of the CC-165. Commanding the CC-165 to Go-Offline tells the CC-165 to ignore the activity on the inputs. Nothing will be reported in the Monitor Activity or Transaction Monitor when a CC-165 is Offline. This can be helpful when these monitor points are tied with alarms and conditional responses that an operator wants to temporarily disarm. Commanding the CC-165 to Go-Online will resume the reporting of the activity for the monitor points. Please note that a specific point cannot be commanded to Go-Offline or Go- Online with the CC-165. All monitor points on the CC-165 Go-Offline (or Online) at the same time. Shunt Times Devices can be set to shunt the user-definable monitor points. In the definition of the monitor point there is a section that states Condition to Shunt. The condition can be shunted for up to 126 seconds. Choosing the No Shunt for the monitor point will cause all activity for the monitor point to be reported immediately. Choosing to shunt the open description for the monitor point determines how long the monitor point must remain open before the condition is reported in the software. Choosing to shunt the closed description for the monitor point determines how long the monitor point must remain closed before the condition is reported in the software. J7 & J15 OUTPUT RELAYS Output Points Five output relays are available on the CC-165. The relays are rated at 120 VAC or 28VDC, both voltages at 3 ma. When each output is energized (in the software definition of the output point, the closed description is the energized state of the relay), the LED associated with the output will emit light. Each output can be linked with commands, conditional responses, and alarm responses in the software. Page 4 Copyright 2009, Access Specialties International, LLC, All Rights Reserved

6 Pulsing Another advantage of the CC-165 is that the outputs are capable of pulsing. Pulsing allows the user to temporarily energize or de-energize any defined outputs for a CC-165. If pulsing is not used, the state of the output relay will be changed permanently. To change back to another state of the outputs, an additional command must be sent to the CC-165. Pulsing is defined in the software device definition. Either the open or closed description can be pulsed for up to 126 seconds. J7 Output Relays 0 and 1 Function J7 CC-165 LED Output 0 Common Pin #1 10 Output 0 Normally Open Pin #2 Output 0 Normally Closed Pin #3 Output 1 Common Pin #4 11 Output 1 Normally Open Pin #5 Output 1 Normally Closed Pin #6 J15 Output Relays 2, 3 & 4 Function J15 CC-165 LED Output 2 Common Pin #1 4 Output 2 Normally Open Pin #2 Output 2 Normally Closed Pin #3 Output 3 Common Pin #4 5 Output 3 Normally Open Pin #5 Output 3 Normally Closed Pin #6 Output 4 Common Pin #7 6 Output 4 Normally Open Pin #8 Output 4 Normally Closed Pin #9 J8 POWER CONNECTION Power J8 12 VAC/12 VDC+ Pin #1 12 VAC/12 VDC- Pin #2 Ground Pin #3 Not Used Pin #4 Page 5 Copyright 2009, Access Specialties International, LLC, All Rights Reserved

7 S1, S2, AND DEGRADED MODE SW1 and SW2 are not used with the CC-165. All dip-switches on the SW1 and SW2 should always be off. When a CC-165 loses communication to the IC-1600 then the CC-165 will go into degraded mode. In Degraded mode any relay that was energized will now de-energize. This is to ensure that doors will lock after communication was lost from the IC-1600 to maintain security. TROUBLESHOOTING TECHNIQUES Tech Tip 1 Verify Communication Between CC-165 and IC Access Gold and Panelcom (PCW) or ASI 2000 and Panel Manager need to be running. 2. Look up the Device number, Channel and Port in Device Definitions/Device Manager. 3. If the device number is unknown, send a signal from the CC-165 by changing the state of a monitor point. 4. In the transaction screen, the signal that was just sent up from the CC-165 should be reported. 5. If nothing is reported then there is no communications to the Host. 6. Edit the IC-1600 and make sure that the channel is checked so the channel is ON. 7. If a Channel Expander is being used turn the corresponding dipswitch on. 8. Look at the channel (or port for a CE-1600) and verify that the LED is flashing (the more channels that are ON, the slower the LEDs will flash). 9. Only Channels and Ports that are being used should be turned on. Tech Tip 2 Verify Communication Between IC-1600 and Server 1. Access Gold and Panelcom or ASI 2000 and Panel Manager need to be running. 2. Open Monitor Activity (AG) or Transaction Monitor (ASI 2000) to watch the real time transactions. 3. Send a signal from the CC-165 by changing the state of a monitor point\ 4. In the transaction screen, the signal that was just sent up from the CC-165 should be reported. If nothing is reported then there is no communications to the Host Page 6 Copyright 2009, Access Specialties International, LLC, All Rights Reserved

8 Tech Tip 3 Find the Device # of the CC-165 (For Access Gold only) 1. Access Gold and Panelcom must be running. 2. Send a signal from the CC-165 by changing the state of a monitor point. 3. In the transaction screen, the signal that was just sent up from the CC-165 should be reported. 4. If nothing is reported then there is no communications to the Host. 5. If there is not a device # assigned to the CC-165, the message Undefined Device will report along with the channel and port # s. 6. Look up the Device number, Channel and Port in Device Definitions for information on the device such as the panel #, channel #, port #, Go and Shunt times, etc. Tech Tip 4 Replace a Comm20RX chip Many times when communications is not functioning between the IC-1600 and the CC-165, the Comm20RX chip has gone bad. The Comm20RX chip is the small green circuit board that is upside down on the bottom board of the CC Remove power from the CC Remove the upper board from the CC Remove the Comm20RX chip from the CC Replace the Comm20RX chip with a known good chip. 5. The Comm20RX board has two J connections. J1 and J2. When replacing any Comm20RX chip the lowest J number always matches the lowest J number. 6. Match J1 on the Comm20RX chip to J7 on the CC Match J2 on the Comm20RX chip to J8 on the CC Replace the upper board on the CC Reapply power to the CC-165. Page 7 Copyright 2009, Access Specialties International, LLC, All Rights Reserved

INSTALLATION & USER'S GUIDE

INSTALLATION & USER'S GUIDE RI-120 READER INTERFACE & Contact Expansion Module CEM-133 INSTALLATION & USER'S GUIDE Page 1 Copyright 2009, Access Specialties International, LLC All Rights Reserved Table of contents Introduction ------------------------------------------------------pg

More information

EQUIPMENT SPECIFICATIONS

EQUIPMENT SPECIFICATIONS EQUIPMENT SPECIFICATIONS IC-1600 Intelligent Controller The IC-1600 Intelligent Controller is a fully intelligent panel that has a complete database on board. It operates in conjunction with the Access

More information

DC-8706K Auto Dial Alarm System

DC-8706K Auto Dial Alarm System DC-8706K Auto Dial Alarm System User Guide Basic Contents: 1x the host unit; 1x wireless door (window) magnet; 1x wireless infrared detector; 2x remote control; 1x siren; 1x phone core; 1x AC to DC power

More information

IPX AUTOMATIC IP NETWORK LOSS BACKUP A/B SWITCH INSTRUCTION BOOK IB6444-02

IPX AUTOMATIC IP NETWORK LOSS BACKUP A/B SWITCH INSTRUCTION BOOK IB6444-02 IPX AUTOMATIC IP NETWORK LOSS BACKUP A/B SWITCH INSTRUCTION BOOK IB6444-02 TABLE OF CONTENTS DESCRIPTION 2 MOUNTING INSTRUCTIONS 2 HOW TO CABLE THE IPX 2/3 POWER SUPPLY INSTALLATION 3 OPERATION 3 CARE

More information

CM705B - Universal Expander Module CM707B - Plug On Zone Expander Security Systems

CM705B - Universal Expander Module CM707B - Plug On Zone Expander Security Systems CM705B - Universal Expander Module CM707B - Plug On Zone Expander Security Systems EN Security System CM705B CM705B - Universal Expander Module The CM705B universal expander provides a cost effective way

More information

1R / 4-BUTTON SERIES

1R / 4-BUTTON SERIES Button 1 1R / 4-BUTTON SERIES VEHICLE SECURITY SYSTEM Standard Features: Two 4-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren Dual stage impact detector Remote

More information

DORMA MODEL PS-406BB POWER SUPPLY INSTALLATION INSTRUCTIONS

DORMA MODEL PS-406BB POWER SUPPLY INSTALLATION INSTRUCTIONS Features: INSTALLATION Install in accordance with NFPA 70. DORMA MODEL PS-406BB POWER SUPPLY INSTALLATION INSTRUCTIONS Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short

More information

S100. GSM House Alarm System. Http://www.GSMalarmsystem.com

S100. GSM House Alarm System. Http://www.GSMalarmsystem.com S100 GSM House Alarm System Http://www.GSMalarmsystem.com 1. Brief introduction The GSM Alarm System is a new security protection solution special for home, house and office and other applications. It

More information

Oil/Grease Point Alarm for Proceptor Separators

Oil/Grease Point Alarm for Proceptor Separators Oil/Grease Point Alarm for Proceptor Separators Outlet Side Proceptor Oil or Grease Separator Point Alarm Switch Applications - Separators - Sumps - Interface Detection Related Materials - Wiring Diagram

More information

NELSON VOLTAGE MONITOR INSTALLATION & PROGRAMMING MANUAL

NELSON VOLTAGE MONITOR INSTALLATION & PROGRAMMING MANUAL NELSON VOLTAGE MONITOR INSTALLATION & PROGRAMMING MANUAL CONTENTS GENERAL INFORMATION...3 INSTALLATION...3 FIELD WIRING...4 PROGRAMMING...4 Circuit Monitor Options...5 Power Frequency...5 Alarm Silence

More information

TrueAlarm Fire Alarm Systems

TrueAlarm Fire Alarm Systems TrueAlarm Systems UL, ULC, CSFM Listed; FM Approved* Network Annunciators; es Features Provides a dedicated local area network (LAN) for connection of a TrueSite workstation server to remote clients: es

More information

Integra32. Integrated Alarm Monitoring and Access Control HARDWARE MANUAL

Integra32. Integrated Alarm Monitoring and Access Control HARDWARE MANUAL Integra32 Integrated Alarm Monitoring and Access Control HARDWARE MANUAL C o p y r i g h t N o t i c e Copyright 1995-2010 by All rights reserved Worldwide. Printed in Canada. This publication has been

More information

Controller Automation, Model II+

Controller Automation, Model II+ Controller Automation Page 2 of 2 Automation with the RADAK II+ power controller II+ I/O Points: Inputs 5 Programmable Digital inputs 2 Dedicated digital inputs (Channel select and External SCR control

More information

SECTION 13850 DETECTION AND ALARM

SECTION 13850 DETECTION AND ALARM SECTION 13850 DETECTION AND ALARM PART 1 GENERAL 1.01 SUMMARY A. Section Includes 1. Control Panel 2 Associated Equipment B. Products Installed But Not Supplied Under This Section 1. Section 16140 - Wiring

More information

INSTALLATION GUIDE. Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930

INSTALLATION GUIDE. Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930 INSTALLATION GUIDE Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930 Card Reader and Controller Model 3.5 with KIM Swipe Reader Table of Contents 1. Features..................................

More information

TX GSM SMS Auto-dial Alarm System. Installation and User Manual

TX GSM SMS Auto-dial Alarm System. Installation and User Manual TX GSM SMS Auto-dial Alarm System Installation and User Manual Product Features: 1. 16 wireless zones, 3 wired zones alarm system, suitable for small to medium size offices and homes. 2. The system uses

More information

8 Channel Status Input Panel model SIP-8

8 Channel Status Input Panel model SIP-8 Description The Sine Systems model SIP-8 Status Input Panel is to be used with the RFC-1/B Remote Facilities Controller. It consists of a long PC board mounted on a 1.75 inch (1U) rack panel. The SIP-8

More information

AC-115 Compact Networked Single Door Controller. Installation and User Manual

AC-115 Compact Networked Single Door Controller. Installation and User Manual AC-115 Compact Networked Single Controller Installation and User Manual December 2007 Table of Contents Table of Contents 1. Introduction...5 1.1 Key Features... 6 1.2 Technical Specifications... 7 2.

More information

SMS Alarm Messenger. Setup Software Guide. SMSPro_Setup. Revision 090210 [Version 2.2]

SMS Alarm Messenger. Setup Software Guide. SMSPro_Setup. Revision 090210 [Version 2.2] SMS Alarm Messenger SMSPro_Setup Revision 090210 [Version 2.2] ~ 1 ~ Contents 1. How to setup SMS Alarm Messenger?... 3 2. Install the SMSPro_Setup software... 5 3. Connection Type... 6 4. Connection Port

More information

INSTALLATION MANUAL VEHICLE SECURITY SYSTEM CE-SS200

INSTALLATION MANUAL VEHICLE SECURITY SYSTEM CE-SS200 INSTALLATION MANUAL VEHICLE SECURITY SYSTEM CE-SS200 FUSION CULTURE TABLE OF CONTENTS There s no point doing something if no one notices. We ve always believed the way to make things happen is by getting

More information

Combi B Alarm box. Mounting instructions

Combi B Alarm box. Mounting instructions Combi B Alarm box Mounting instructions EN Mounting instructions Alarm box Combi B VdS, G113064, G113065, G113066 Table of Contents 1 Description... 3 2 System overview... 3 3 Structure... 3 3.1 Power

More information

UNC500 HARDWARE MANUAL. new generation building security

UNC500 HARDWARE MANUAL. new generation building security UNC500 HARDWARE MANUAL new generation building security Copyright Notice Copyright 1995-2012 by All rights reserved Worldwide. Printed in Canada. This publication has been provided pursuant to an agreement

More information

MODEL CA100 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS

MODEL CA100 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS MODEL CA100 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM Black Antenna Wire 6 Pin 6 Pin Mini Connector Valet Switch Blue LED Indicator Blue Wire: (-) 200mA Unlock

More information

Controller 5000GL Controller 5000GL provides flexible system architecture with options of GBUS and LOCAL BUS communications to field devices, to meet a wide range of site requirements. GGBUS L LOCAL BUS

More information

SMART SENSOR COLLECTION

SMART SENSOR COLLECTION TEMPERATURE SENSOR This sensor measures temperature in degrees Celsius or Fahrenheit. It works with all SensorHawk base units (SensorHawk-2, SensorHawk-8 and SensorHawk8/20) as well as the SecurityHawk-8

More information

Understanding Emergency Power Off (EPO)

Understanding Emergency Power Off (EPO) Understanding Emergency Power Off (EPO) White Paper #22 Executive Summary Emergency Power Off (EPO) is the capability to power down a piece of electronic equipment or an entire installation from a single

More information

ImproX IXP20 Controller INSTALLATION MANUAL

ImproX IXP20 Controller INSTALLATION MANUAL MODEL NUMBER: ISC910-1-0-GB-XX ISC911-5-0-GB-XX IXP20 CONTROLLER SPECIFICATIONS Working Environment Plastic Housing... Power ImproX IXP20 Controller INSTALLATION MANUAL Designed to work in an indoor (dry)

More information

Wireless Alarm system s manual

Wireless Alarm system s manual MOUNTVIEW TECH AUSTRALIA PTY LTD Wireless Alarm system s manual ADS A180 Series ADS Security 1/11/2011 1. Before You Begin For your safety and the safety of others, and to ensure that you get the most

More information

Advantium 2 Plus Alarm

Advantium 2 Plus Alarm ADI 9510-B Advantium 2 Plus Alarm INSTALLATION AND OPERATING INSTRUCTIONS Carefully Read These Instructions Before Operating Carefully Read These Controls Corporation of America 1501 Harpers Road Virginia

More information

WIRING HARNESS FOR AS635P4. BLUE PLUG RED, BLUE, BLACK, WHITE - Plug in dual stage sensor harness

WIRING HARNESS FOR AS635P4. BLUE PLUG RED, BLUE, BLACK, WHITE - Plug in dual stage sensor harness WIRING HARNESS FOR AS635P4 ANTENNA NOT USED 5 PIN WHITE PLUG 2 PIN WHITE PLUG GREEN - PARKING BRAKE INPUT (-) BLUE - NOT USED 3 PIN BLUE PLUG RED, BLUE, BLACK, WHITE - Plug in dual stage sensor harness

More information

Automatic Transfer Switch FT-10 Network Control Communications Module (CCM-T) Kit 541 0811

Automatic Transfer Switch FT-10 Network Control Communications Module (CCM-T) Kit 541 0811 Instruction Sheet 1-2003 Automatic Transfer Switch FT-10 Network Control Communications Module (CCM-T) Kit 541 0811 PURPOSE OF KIT A CCM-T is used to monitor and control an automatic transfer switch. The

More information

SDV1092-8 Music Mixer / Equaliser Installation guide and user manual

SDV1092-8 Music Mixer / Equaliser Installation guide and user manual EIGHT CHANNEL MIXER/EQUALISER SDV1092-8 Music Mixer / Equaliser Installation guide and user manual 1 CONTENTS CONTENTS...2 SAFETY NOTES...3 INTRODUCTION...4 USER CONTROLS...7 VOLUME CONTROL...7 MUSIC SOURCE

More information

APR-PRT3 Printer Module: C-Bus Programming Instructions

APR-PRT3 Printer Module: C-Bus Programming Instructions APR-PRT3 Printer Module: C-Bus Programming Instructions We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us

More information

Single Port Gigabit Ethernet Media Converter Board (P/N 201350-xxx) User s Manual And Troubleshooting Guide

Single Port Gigabit Ethernet Media Converter Board (P/N 201350-xxx) User s Manual And Troubleshooting Guide Single Port Gigabit Ethernet Media Converter Board (P/N 201350-xxx) User s Manual And Troubleshooting Guide August 12, 2009 Rev C Moog Components Group Springfield Operations 750 West Sproul Road Springfield,

More information

MODEL 5010 DUAL CHANNEL SMOKE/FIRE DETECTION MODULE

MODEL 5010 DUAL CHANNEL SMOKE/FIRE DETECTION MODULE DESCRIPTION MODEL 5010 DUAL CHANNEL SMOKE/FIRE DETECTION MODULE DESCRIPTION The SST Model 5010 Two Channel Smoke/Fire Detection Module provides two independent detection input channels for the NOVA-5000

More information

EMBEDDED ACCESS CONTROL Hardware Installation Guide

EMBEDDED ACCESS CONTROL Hardware Installation Guide EMBEDDED ACCESS CONTROL Hardware Installation Guide Lenel goentry Hardware Installation Guide, product version 1.00. This guide is item number DOC- ENHW-ENU, revision 1.003, April 2009 Copyright 2009 Lenel

More information

Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2. Instruction Manual

Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2. Instruction Manual Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2 Instruction Manual Firmware version: 2.0.1 Issue: 0.6 Version of the GPRS transmitters configurator: 1.3.6.3 Date of issue: 07.03.2012 TABLE OF CONTENTS

More information

FDX Spider ALARM SYSTEM SHORT FORM USER GUIDE V1.6. SyxthSense Ltd www.syxthsense.com

FDX Spider ALARM SYSTEM SHORT FORM USER GUIDE V1.6. SyxthSense Ltd www.syxthsense.com FDX Spider ALARM SYSTEM SHORT FORM USER GUIDE V1.6 SyxthSense Ltd www.syxthsense.com 1 1. ARMING THE SYSTEM 1.1 General The SyxthSense Spider alarm system can be armed using a card (RFID tag) reader, display

More information

Remote Control Cut Off Switch NEFA20 Plus F1

Remote Control Cut Off Switch NEFA20 Plus F1 Remote Control Cut Off Switch NEFA20 Plus F1 Installation Guide Please read this entire guide before beginning the installation! Supplied Parts Antenna NEFA20 F1 Plus Cutoff Switch Protective Covers DIN

More information

535T Window Automation System

535T Window Automation System 535T Window Automation System Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained

More information

Applied Electronics. Commercial Dimming System UPDATE NOTICE

Applied Electronics. Commercial Dimming System UPDATE NOTICE REV. A Applied Electronics Commercial Dimming System UPDATE NOTICE This notice is to inform the end user of an additional feature added to this DP12/2400 dimming unit. This unit has been outfitted with

More information

HM-W536 Install Guide

HM-W536 Install Guide HM-W536 Install Guide 9/13/2013 IMPORTANT SAFETY INSTRUCTIONS Warning - When using electrical devices, basic safety precautions should be followed to reduce the risk of fire, electrical shock or injury.

More information

Using your LED Plus keypad

Using your LED Plus keypad Using your LED Plus keypad System 238 System 2316 System 238i System 2316i Part Number 5-051-372-00 Rev B Thank you for purchasing this C&K alarm system Your system is one of the most powerful and advanced

More information

ADEMCO LYNXR-I Security Systems

ADEMCO LYNXR-I Security Systems K14117 3/06 Rev. A ADEMCO LYNXR-I Security Systems Quick Start Guide UL LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC or LYNXRCHKIT-SHA)

More information

T7560A,B,C Digital Wall Module

T7560A,B,C Digital Wall Module T7560A,B,C Digital Wall Module HONEYWELL EXCEL 5000 OPEN SYSTEM BEFORE INSTALLATION All wiring must comply with local electrical codes and ordinances or as specified on installation wiring diagrams. Digital

More information

iflex 2400 DSP Automatic Mixer Installation & Operation Manual for the Ivie February, 2009 Copyright 2009 by Ivie TechNologies Inc.

iflex 2400 DSP Automatic Mixer Installation & Operation Manual for the Ivie February, 2009 Copyright 2009 by Ivie TechNologies Inc. Installation & Operation Manual for the Ivie iflex 2400 DSP Automatic Mixer February, 2009 Copyright 2009 by Ivie TechNologies Inc. Introduction The iflex Integrated Automixer/Digital Signal Processor

More information

782 Electric Latch Retraction Controller Installation Instructions

782 Electric Latch Retraction Controller Installation Instructions 782 Electric Latch Retraction Controller Installation Instructions The 782 is designed to be used with UL Listed Yale 7000P series (electric latch retraction) or Corbin Russwin ED4000/ED5000 x M94 series

More information

VEHICLE SECURITY SYSTEM G25/G20

VEHICLE SECURITY SYSTEM G25/G20 VEHICLE SECURITY SYSTEM G25/G20 Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will

More information

2000e & 2000eM Keypad Installation & Programming Instructions

2000e & 2000eM Keypad Installation & Programming Instructions 2000e & 2000eM Keypad Installation & Programming Instructions Note: This product is designed to be installed and serviced by security and lock industry professionals. Specifications Parameter Voltage Requirements

More information

INSTALLATION MANUAL 3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS

INSTALLATION MANUAL 3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS 3RP / 5RP 4-BUTTON SERIES VEHICLE SECURITY SYSTEMS INSTALLATION MANUAL Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the

More information

ViZion Installation Guide

ViZion Installation Guide ViZion Installation Guide v2.0 1 ViZion Installation Guide Table of Contents Inventory Hardware Setup Understanding Synchronization Cable Begin by taking an inventory of the required equipment DR Unit

More information

Fire Pump Controllers Remote Alarm Panels

Fire Pump Controllers Remote Alarm Panels Fire Pump Controllers Remote Alarm Panels Remote Alarm Panels 1.8 Remote Alarm Panels FDAP-M Electric... DFDAP-M Diesel... Product Specifications... 2 6 9 Features 1-1 DFDAP-M / FDAP-M Remote Alarm Panel

More information

PRO PLM Installation Instructions

PRO PLM Installation Instructions PRO PLM Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

Business/Home GSM Alarm System. Installation and User Manual

Business/Home GSM Alarm System. Installation and User Manual Business/Home GSM Alarm System Installation and User Manual Brief Introduction: GSM 900/1800/1900 bands, can be used in most parts of the world Full duplex communication with the host Monitor the scene

More information

Water Leak Detection System

Water Leak Detection System Water Leak Detection System Installation and Operating Manual 505-334-5865 ph 505-334-5867 fax www.rodisystems.com email:info@rodisystems.com 936 Highway 516 Aztec, NM 87410-2828 Manual Revisions and Copyright

More information

H Unit Input/Output Manual

H Unit Input/Output Manual H Unit Input/Output Manual 4 INPUTS 4 OUTPUTS RS485 Table of Contents Safety Rules...Inside Front Cover. Introduction...IFC 2. Communications...IFC 2.2 Baud Rate...IFC 2.3 Modbus Address... 2.4 Speed of

More information

Memcom Emergency Telephone

Memcom Emergency Telephone Memcom Emergency Telephone Installation Guide Ref No. 450 900 (GB) Version 2 + + Simple wiring for quick installation + + Integrated LCD display shows you what you have programmed + + All code based programming

More information

Fiber Optic Selector Guide for Analog & Digital Data Links, Contact Closures & Multiplexers

Fiber Optic Selector Guide for Analog & Digital Data Links, Contact Closures & Multiplexers Fiber Optic Selector Guide for Analog & Digital Data Links, Contact Closures & Multiplexers Analog Data Links Multi-Channel Contact Closures Multiplexers Digital Data Links - Contact Closures Power Supply

More information

INSTALLATION GUIDE OWNER S GUIDE

INSTALLATION GUIDE OWNER S GUIDE INSTALLATION GUIDE OWNER S GUIDE KEYLESS ENTRY MODELS KE100 / KE150 / 1702 CONTENTS System Features... 1 System Components... 1 Technical Assistance... 1 Before You Begin... 1 Precautions... 1-2 Making

More information

5-port / 8-port 10/100BaseTX Industrial Ethernet Switch User Manual

5-port / 8-port 10/100BaseTX Industrial Ethernet Switch User Manual 5-port / 8-port 10/100BaseTX Industrial Ethernet Switch User Manual Content Overview... 1 Introduction... 1 Features... 3 Packing List... 4 Safety Precaution... 4 Hardware Description... 5 Front Panel...

More information

Owner's Manual [ S/N LABEL HERE ] Document # BW-BCU5DOC

Owner's Manual [ S/N LABEL HERE ] Document # BW-BCU5DOC Owner's Manual [ S/N LABEL HERE ] Document # BW-BCU5DOC BAYweb Remote Model BW-BCU5 Owner's Manual Copyright 2009-2010 Bay Controls, LLC Part Number: BW-BCU5DOC Revision: 0.2 April 18, 2010 BAYweb is a

More information

Technical Overview Add-on Sensors - Smoke Alarm. Get yours direct at: 01491 410913 www.theclimate.co.uk

Technical Overview Add-on Sensors - Smoke Alarm. Get yours direct at: 01491 410913 www.theclimate.co.uk Technical Overview Add-on Sensors - Smoke Alarm Get yours direct at: 01491 410913 www.theclimate.co.uk OVERVIEW This kit contains a standard smoke alarm and relay pattress. The Kidde Smoke Alarm supplied

More information

RCP-0006 Through RCP-0042 System Manual

RCP-0006 Through RCP-0042 System Manual Touch-Plate Lighting Controls RCP SERIES RCP Series System Manual RCP-0006 Through RCP-0042 System Manual Touch-Plate Lighting Controls 1830 Wayne Trace Fort Wayne, IN 46803 Phone: 260-424-4323 Fax: 260-420-3651

More information

TEMON 8-C. Doc. N MO-0370-ING TEMPERATURE MONITOR DEVICE TYPE TEMON 8-C OPERATION MANUAL. Microener - Copyright 2010 FW 2.2 Date 01.12.2008 Rev.

TEMON 8-C. Doc. N MO-0370-ING TEMPERATURE MONITOR DEVICE TYPE TEMON 8-C OPERATION MANUAL. Microener - Copyright 2010 FW 2.2 Date 01.12.2008 Rev. TEMPERATURE MONITOR DEVICE TYPE TEMON 8-C OPERATION MANUAL Microener - Copyright 2010 FW 2.2 Date 01.12.2008 Rev. 0 1. Generality 3 2. Introduction 3 3. Accessories and Options 3 4. Installation 3 5. Connection

More information

Streaming Potential System (SPT1000, SPD1000)

Streaming Potential System (SPT1000, SPD1000) Streaming Potential System (SPT1000, SPD1000) User's Manual Sentrol Systems, Inc. 3949 Cotswold Dr. SW, Lilburn, GA 30047-2371 Tel: 770-564-1541, Fax: 770-564-8605 www.sentrolsystems.com Since the streaming

More information

MONITOR ISM / AFx Multi-Tenant Security System User Guide V1.3

MONITOR ISM / AFx Multi-Tenant Security System User Guide V1.3 MONITOR ISM / AFx Multi-Tenant Security System User Guide V.3 Multi-Tenant Security System User Guide Welcome New Users! There are two types of suite security keypads. Follow the instructions in the proceeding

More information

Rack mounted telephone- and leased line modem for industrial applications

Rack mounted telephone- and leased line modem for industrial applications Rack mounted telephone- and leased line modem for industrial applications TR-6 Rack modem for industrial PSTNand /-wire leased line applications The TR-6 is an analogue V. 9 -rack PSTN modem as well as

More information

www.sebury.com.cn Digital Keypad Use s Manual

www.sebury.com.cn Digital Keypad Use s Manual K3 K4 www.sebury.com.cn Digital Keypad Use s Manual Contents Introduction Introduction Specifications Intramural Interface Circuit 3 Mounting 3 Wiring 5 Power UP 7 Engineer Programming Mode 7 The K3/K4

More information

Installation, Operation & Maintenance of the T 3 SQ Analog VAV Diffuser

Installation, Operation & Maintenance of the T 3 SQ Analog VAV Diffuser T3SQ-1-IOM-1.0 6-6-09 Step 1 Installation, Operation & Maintenance of the T 3 SQ Analog VAV Diffuser The units should be shipped assembled except for the backpan. The thermal T 3 SQ is shipped with additional

More information

Ademco Vista-20P/First Alert FA-168C Basic Commands

Ademco Vista-20P/First Alert FA-168C Basic Commands Zones 64 total Ademco Vista-20P/First Alert FA-168C Basic Commands Wireless Yes, Zones 09 to 48 + 16 Keyfob Zones (Zones 49 to 64) Batteries Downloadable Partitions 2 12 volt Rechargable inside main Panel,

More information

Manual for Fire Suppression & Methane Detection System

Manual for Fire Suppression & Methane Detection System Manual for Fire Suppression & Methane Detection System Fogmaker North America Post address: 150 Gordon Dr Exton, PA 19341 Delivery address: 150 Gordon Dr Exton, PA 19341 Tel: 610-265-3610 Fax: 610-265-8327

More information

Digital I/O: OUTPUT: Basic, Count, Count+, Smart+

Digital I/O: OUTPUT: Basic, Count, Count+, Smart+ Digital I/O: OUTPUT: Basic, Count, Count+, Smart+ The digital I/O option port in the 4-Series provides us with 4 optically isolated inputs and 4 optically isolated outputs. All power is supplied externally.

More information

Alarm Kit Installation Instructions I-ED01181

Alarm Kit Installation Instructions I-ED01181 DEVICES COVERED IN THIS DOCUMENT: 4940 Alarm Kit (ALT, ALM, ALL) 2-649-0168 Latch Monitor Switch 2-649-1090 Tamper Switch OVERVIEW Page 1 of 8 ALARM KIT INSTALLATION STEP ONE Disassemble device if it was

More information

Shadow TX(A) Shadow RX

Shadow TX(A) Shadow RX Shadow TX(A) Shadow RX Asset Management and RFID Transmitter Tags Asset Management Receiver The Shadow TX(A) and Shadow RX wireless asset management system is a standalone wireless asset tracking system

More information

Pop-up Surveillance Camera On Your TV

Pop-up Surveillance Camera On Your TV Pop-up Surveillance Camera On Your TV Would you like to automatically see who s at your front door, even before they ring the doorbell? It s easy to do! Just follow the simple steps described below. CAMERA

More information

1pcs. 1pcs. 2pcs 1pcs 1pcs 2pcs

1pcs. 1pcs. 2pcs 1pcs 1pcs 2pcs Home security alarm system LX-HS06 Instruction Brief introduction LX-HS06 is a set of entirely new English home security alarm system, it uses advanced MCU control and SMD technology. it innovate multiple

More information

HAM841K ALARM CONTROL PANEL FOR COMMERCIAL AND RESIDENTIAL SECURITY SYSTEMS

HAM841K ALARM CONTROL PANEL FOR COMMERCIAL AND RESIDENTIAL SECURITY SYSTEMS ALARM CONTROL PANEL FOR COMMERCIAL AND RESIDENTIAL SECURITY SYSTEMS USER MANUAL USER MANUAL ALARM CONTROL PANEL FOR COMMERCIAL AND RESIDENTIAL SECURITY SYSTEMS INTRODUCTION The (HA-841K) is a complete

More information

Six-defense zone Display Alarm System. User Manual

Six-defense zone Display Alarm System. User Manual Six-defense zone Display Alarm System User Manual Feature 1. Anti-interfere function. When someone interferes it with same frequency, the control unit will activate siren to alarm. 2. Support anti-decode

More information

Understanding Alarm Systems

Understanding Alarm Systems Understanding Alarm Systems A false alarm occurs when an alarm signal designed to elicit an immediate emergency Law Enforcement, Fire, or Medical response is activated, when in fact no emergency exists.

More information

GSM AUTO DIALER. Remote Monitoring & Control using your mobile phone. www.gsm-activate.co.uk

GSM AUTO DIALER. Remote Monitoring & Control using your mobile phone. www.gsm-activate.co.uk GSM AUTO DIALER Remote Monitoring & Control using your mobile phone www.gsm-activate.co.uk Product Information Our GSM Auto-Dialer is a versatile unit which can be attached to many of your electronic devices

More information

Alarm Security Kit - NVR

Alarm Security Kit - NVR Alarm Security Kit - NVR EN The alarm configuration menu (see above right screenshot) allows you to configure and change settings for the PIR movement sensors, window/door sensors, remote controls (key

More information

INSTALLATION GUIDE. www.security.soundstream.com FCC ID NOTICE

INSTALLATION GUIDE. www.security.soundstream.com FCC ID NOTICE AL.1 AUTO SECURITY SYSTEM INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device

More information

Provides an activation of Relay 1 triggered by Input 1. The function also provides an option for reverse-logic on the activation of Input 1.

Provides an activation of Relay 1 triggered by Input 1. The function also provides an option for reverse-logic on the activation of Input 1. 1 Description The is a programmable 3 relay logic module that may be used for multiple applications, including simple timing, door mounted sensor inhibiting and advanced relay sequencing. The contains

More information

ZC-24DO CANopen I/O Module: 24 Digital Outputs

ZC-24DO CANopen I/O Module: 24 Digital Outputs Z-PC Line EN ZC-24DO CANopen I/O Module: 24 Digital Outputs Installation Manual Contents: - General Specifications - Technical Specifications - Installation Rules - Electrical connections - DIP-switches

More information

IAdea GPIO Extender Application Note

IAdea GPIO Extender Application Note IAdea GPIO Extender Application Note Contents Introduction... 1 What is GPIO Extender?... 1 Digital Input and Output Applications... 2 Wiring Instructions... 4 Software Instructions... 7 Setup Example

More information

Shunt lock function 3066

Shunt lock function 3066 Version: January 2004 Contents Alarm System Activation unit Deactivation unit Digital locking cylinder or Smart Relay 1.0 Method of Operation 4 1.1 General 4 1.2 Turning the Alarm System On 4 1.3 Turning

More information

IDS. Users Guide to Keypad Functions S E C U R I T Y MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18

IDS. Users Guide to Keypad Functions S E C U R I T Y MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18 INHEP DIGITAL IDS S E C U R I T Y Users Guide to Keypad Functions MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Away Arm Stay

More information

Frequently Asked Questions for TFT Remote Controlled Monitors. First Rev 4/6/2005 SGMc Second Rev 5/7/2005 Third Rev 11/15/2005

Frequently Asked Questions for TFT Remote Controlled Monitors. First Rev 4/6/2005 SGMc Second Rev 5/7/2005 Third Rev 11/15/2005 Frequently Asked Questions for TFT Remote Controlled Monitors. First Rev 4/6/2005 SGMc Second Rev 5/7/2005 Third Rev 11/15/2005 1. What was the primary spark that started the fire under TFT to make remote

More information

GSM-AUTO+ GSM Controller with Internal Power Supply User manual

GSM-AUTO+ GSM Controller with Internal Power Supply User manual GSM-AUTO+ GSM Controller with Internal Power Supply User manual INDEX Description... 2 Preparing the SIM card... 3 Installation... 4 Example connections... 5 Programming commands... 6 Quick reference of

More information

rpsa FIRE PROTECTION ENGINEERS

rpsa FIRE PROTECTION ENGINEERS R.P. SCHIFILITI ASSOCIATES, INC. P.O. Box 297 Reading, Massachusetts 01867-0497 USA 781.944.9300 Fax / Data 781.942.7500 Telephone Sample Fire Alarm System Calculations 1. A fire alarm manufacturer specifies

More information

GSM home alarm system s manual

GSM home alarm system s manual GSM home alarm system s manual I. Main features: 1, Eight wireless LED zone, and four wired zone 2, Two-way to communication 3, The system supports the GSM cell phones, no need the fixed telephone line.

More information

Overview. Alarm console supports simultaneous viewing of both live and recorded video when alarm events are selected

Overview. Alarm console supports simultaneous viewing of both live and recorded video when alarm events are selected Niagara Security Overview Niagara Security by Tridium, is an open, web-based security management solution that allows you to manage and monitor your facility anytime, anywhere. Built on Tridium s Niagara

More information

INSTALLATION/PROGRAMMING INSTRUCTIONS E4KP ENTRYCHECK

INSTALLATION/PROGRAMMING INSTRUCTIONS E4KP ENTRYCHECK Security Door Controls 3580 Willow Lane, Westlake Village, CA 91361-4921 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION/PROGRAMMING INSTRUCTIONS E4KP

More information

AE8-1328 R5 March 2011. Copeland Digital Compressor Controller AE8-1328 R5. Specifications

AE8-1328 R5 March 2011. Copeland Digital Compressor Controller AE8-1328 R5. Specifications AE8-1328 R5 March 2011 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital compressor or the Copeland

More information

CB Svendsen A/S PS 2015.08.02/ rev. 1.5

CB Svendsen A/S PS 2015.08.02/ rev. 1.5 CB Svendsen A/S PS 0.0.0/ rev... Description Installation guide for. The is designed for copying of signals from electricity-, heat- or water meters to s. This way, it is possible to connect a data logger

More information

FLEET MANAGEMENT & CAR SECURITY SYSTEM GPRS/GPS

FLEET MANAGEMENT & CAR SECURITY SYSTEM GPRS/GPS FLEET MANAGEMENT & CAR SECURITY SYSTEM FOR PROVIDERS AND CUSTOMERS The Tracker Server Communication Program for data collection The Tracker Client Map Program intended for dispatching desks The GSM/GPRS

More information

Users Guide to Keypad Functions

Users Guide to Keypad Functions Users Guide to Keypad Functions MANUAL NO. 700-175-01J ISSUED JAN 2002 VERSION 1.41 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Panic Fire Medical Away Arm Stay Arm Stay Arm &

More information

OPERATING MANUAL. Table of contents. 2 Phase Stepping Motor Driver 2M542. Rev. A. Introduction page 2. Specifications page 2 Timing chart page 3

OPERATING MANUAL. Table of contents. 2 Phase Stepping Motor Driver 2M542. Rev. A. Introduction page 2. Specifications page 2 Timing chart page 3 2 Phase Stepping Motor Driver 2M542 OPEATING MANUAL Table of contents Introduction page 2 Specifications page 2 Timing chart page 3 Setting page 4 Current set page 4 educe current function page 4 Micro

More information

Electronic Control Devices The European Product Catalogue 2007

Electronic Control Devices The European Product Catalogue 2007 FX07 Field Controller (1/4) FX07 Field Controller Display Model Dimensions in mm (inches) The FX07 is a terminal unit controller in the Facility Explorer range of products. The controller is designed specifically

More information

Application/Connection Examples

Application/Connection Examples This Quick Start Guide is designed to familiarize the user with the connection and configuration of the DTS-305 DIN rail mounted single / 3 phase power & energy meter with RS-485 or TCP communications.

More information