TRUCK MOUNTED HYDRAULIC CRANE

Transcription

1 TRUCK MOUNTED HYDRAULIC CRANE

2 Superstructure Specifications Boom (Standard) 36 ft. - ft. (10.9 m m) four section full power boom. Equipped with remote greasg les for upper wear pad area. Maximum Tip Height: 118 ft. (.9 m). Foldg Lattice Extension ft. (33.5 m) Ma boom 31 ft. or 56 ft. (9.4 m or 17 m) foldg lattice swgaway extension offsettable at, or. Stows alongside base boom section. Maximum Tip Height: 172 ft. (52.4 m). *Boom (Optional) ft ft. (12.2 m m) four section full power boom. Equipped with remote greasg les for upper wear pad area. Maximum Tip Height: 133 ft. (.5 m). *Lattice Extension 125 ft. (38.1 m) Ma boom ft. - ft. (10.7 m m) telescopg lattice swgaway extension offsettable at 2 or. Stows alongside the base boom section. Maximum Tip Height: 191 ft. (58.2 m). *Boom (Optional) ft ft. (10.8 m - 42 m) five section full power boom. Equipped with remote greasg les for upper wear pad area. Maximum Tip Height: 147 ft. (44.8 m). *Foldg Lattice Extension 138 ft. (42 m) Ma boom 31 ft. or 56 ft. (9.4 m or 17 m) foldg lattice swgaway extension offsettable at, or. Stows alongside the base boom section. Maximum Tip Height: 202 ft. (61.5 m). *Optional Luffg Lattice Extension 138 ft. (42 m) Ma boom. 31 ft. or 56 ft. (9.4 m or 17 m) foldg lattice swgaway extension hydraulically offsettable from the superstructure cab. Infite offsets through. Stows alongside the base boom section. Maximum Tip Height: 202 ft. (61.5 m). Boom Nose Five nylatron sheaves (six with 125 boom), mounted on heavy duty tapered roller beargs with removable p-type rope guards. Quick reevg type boom nose. Removable auxiliary boom nose with removable p type rope guard. Boom Elevation One double actg hydraulic cylder with tegral holdg valve provides elevation from -3 to (-3 to 78 with 125 ft. boom). Cab High visibility, all steel cab with acoustical lg and tted safety glass throughout. Deluxe seat with armrest mounted hydraulic sgle axis controls. Dash panel corporates gauges for all enge functions. Other standard features clude: slidg side and rear wdows, hot water heat, electric wdshield wash/wipe, circulatg air fan, slidg skylight with sunscreen and electric skylight wiper, fire extguisher, cup holder. Swg Planetary swg with foot applied multi-disc wet brake. Sprg applied, hydraulically released parkg brake, plunger type mechanical house lock and 3 house lock operated from cab. Maximum speed: 2.0 RPM. Counterweight 8,0 lbs. (3856 kg) total consistg of (1) 5,0 lbs. (2495 kg) section and (1) 3,000 lbs. (1361 kg) section. Hydraulic stallation/removal. *Optional 9,0 lbs. (49 kg) to be used conjunction with standard counterweight to provide 12,0 lbs. (56 kg) or 18,000 lbs. (8165 kg) total counterweight. Hydraulic System Four ma gear pumps with a combed capacity of 1 GPM (7.5 lpm). Three dividual valve banks. Return le type filter with full flow by-pass protection and service dicator. Replaceable cartridge with beta ratg of 5/12/16. 1 gallons (643 L) reservoir. Remote mounted oil cooler with thermostatically controlled hydraulic motor driven fan. Hoist specifications Ma and Auxiliary Hoists - Model HO3OG-26G Planetary reduction with tegral automatic brake, electronic hoist drum rotation dicator, hoist drum cable follower and grooved drum. Maximum Hoist Le Pull: 17,866 lb. (8103 kg) Maximum Rope Permissible Le Pull: 12,920 lb. (58 kg) Maximum Sgle Le Speed: 4 fpm (154 m/m) Rope Diameter: 3/4. (19 mm) Rope Length: 620 ft. (189 m) Maximum Rope Stowage: 1,163 ft. (4 m) *Denotes optional equipment Load Moment & Anti-Two Block System Standard load moment and anti-two block system with audiovisual warng and control lever lockout. These systems provide electronic display of boom angle, boom length, radius, tip height, relative load moment, maximum permissible load, load dication and warng of impendg two-block condition. 2 GROVE TMS875C

3 Carrier Specifications Chassis Triple box section, four-axle carrier fabricated from highstrength, low alloy steel with towg and tie-down lugs. Outrigger System Four hydraulic telescopg, two-stage, double box beam outriggers with verted jack and tegral holdg valves. Quick release type outrigger floats 24. (610 mm) diameter. Three position settg with fully extended, termediate (%) extended and fully retracted capacities. Maximum outrigger pad load:,0 lbs. ( 587 kg). Outrigger Controls Located the superstructure cab on left side (umbilical design) and on either side of carrier with lighted boxes. Requires two hand operation. Crane level dicator (sight bubble) on right side console. Enge Cumms ISM 0 diesel, six cylders, turbo-charged after cooled, 661 cu.. (10.8 L), 0 bhp (298 kw) 10 RPM. Maximum torque 1,4 ft. lbs. ( RPM. Equipped with enge brake and audio-visual enge distress system. Fuel Tank Capacity gallons (376 L). Transmission Roadranger 11 speeds forward, 3 reverse. Drive 8 x 4 x 4. Steerg Front axle, sgle circuit, mechanical steerg with hydraulic power assist. Turng radius: ' 1". Axles Front: (2) Eaton beam-type steerg axles, 84. (2.13 m) track. Rear: (2) Eaton sgle reduction drive axles, (1.89 m) track. Inter-axle differential locks. Brakes S-cam, dual air split system operatg on all wheels. Sprgapplied, air released parkg brake actg on rear axles. Air dryer. Suspension Front: Walkg beam with air bags and shock absorbers. Rear: Walkg beam with air bags and shock absorbers. Tires Front: 4/65R 22.5 Goodyear G286, tubeless, mounted on alumum disc wheels. Rear: 315/R 22.5 Goodyear G286, tubeless, mounted on alumum disc wheels. Lights Full lightg package cludg turn dicators, head, tail, brake, and hazard warng lights. Cab One man design, all steel fabricated with acoustical lg and tted safety glass throughout. Deluxe fabric covered seat with air height adjustment. Complete drivg controls and enge strumentation cludg tilt telescope steerg wheel, tachometer, speedometer, voltmeter, water temp., oil pressure, fuel level, air pressure gauge with A/V warng and enge high temp./low oil pressure A/V warng. Other standard items clude hot water heater/defroster, electric wdshield wash/wipe, fire extguisher, seat belt, door lock and electric wdow. Electrical System Two 12 V - matenance free batteries. 12 V carrier drivg lights, remag systems 24 V Standard battery disconnect. Maximum Speed 65 MPH (104 kph). Gradeability (Theoretical) 83%. Miscellaneous Standard Equipment Alumum fenders with rear storage compartments; dual rear view mirrors; electronic back-up alarm; slg/tool box; pump disconnect; tire flation kit; air cleaner restriction dicator; block and ball stowage; and chrome package which cludes alumum wheels. Optional Equipment *Cold Weather Package (Includes cold weather kit for ma and auxiliary hoist, remote controlled heated carrier mirrors). *Auxiliary Lightg Package (Includes cab mounted work lights, boom base mounted floodlights, hoist mounted work light). *Flashg Light Package (Includes amber strobe for superstructure and carrier cabs). *Trailg Boom Package (Includes trailer air and electrical disconnects, and trailg boom kit [less dolly]). *Air conditiong, either cab. *Remote controlled cab mounted work lights. *Hookblocks and headache ball. *Ptle hook (rear). *Cross axle differential locks. *Alumum outrigger pads. *Air horn. *LMI light bar. *PAT data logger. *Grease system for turntable, air powered. *On rubber load chart, cludg calibration. *Denotes optional equipment *Optional Tires Front: 4/65R 22.5 Bridgestone M844F, tubeless. 4/65R 22.5 Michel XZY (WB), tubeless. Rear: 315/R 22.5 Bridgestone M843, tubeless. 315/R 22.5 Michel XZY-1 tubeless. GROVE TMS875C 3

4 Dimensions Boom Option ' 125' 138' A 43' 4" 47' 5" 43' 3" B 5' 11" 6' 0" 7' 0" C 4' 4" 8' 5" 4' 3" A B C 1'-8" (0.53 m) GVW Front Rear lb. kg lb. kg lb. kg Axle/Tire Allowable Weights 109,200 49,533 49,200 22,317,000 27,216 TMS875C Basic Mache with ft. boom, 79,961 36,2 34,392 15,0,569 20,6 ma and auxiliary hoists w/ rope, and no counterweight. Add: 3,000 lb. counterweight (superstructure) 3,000 1,361-1, ,3 1,975 Add: 5,0 lb. counterweight (superstructure ) 5,0 2,495-2,4-1,125 7,9 3,620 Add: 9,0 lb. counterweight (superstructure) 9,0 4,9-4,284-1,943 13,784 6,252 Add: 3,000 lb. counterweight ( carrier) 3,000 1,361 2,4 1, Add: 5,0 lb. counterweight ( carrier) 5,0 2,495 4,958 2, Add: 9,0 lb. counterweight ( carrier) 9,0 4,9 8,564 3, Add: 75 ton, 6 sheave hookblock (stowed 1, ,443 1, trough) Add: ton, 3 sheave hookblock (stowed , trough) Add: 10 ton headache ball (stowed trough) Substitute: 125 ft. Boom 3,9 1,1 5, 2,313-1,1-515 Substitute: 138 ft. Boom 4,211 1,910 2,971 1,348 1,2 562 Remove: Auxiliary hoist cable ,122-9 ft. and 138 ft. Boom Options Add: 31 ft. Fixed length extension 1, , Add: 31 ft ft. Bi-fold extension 2,2 1,016 1, Add: 31 ft ft. Luffg bi-fold extension (138 3,122 1,416 3,298 1, ft. boom only) Add: Auxiliary boom nose ft. Boom Options Add: ft. Fixed length extension 2, ,362 1, Add: ft. - ft. telescopic extension 2,893 1,312 3,172 1, Add: Auxiliary boom nose GROVE TMS875C

5 Workg Range 36- ft. ( m) ft. ( m) 18,000 lbs. (8165 kg) % 3 FEET 200 (BOOM DEFLECTION NOT SHOWN) HEIGHT FROM THE GROUND IN FEET 1 1 BOOM & EXTENSION LENGHT IN FEET MAX. BOOM ANGLE OPERATING RADIUS IN FEET FROM AXIS OF ROTATION AXIS OF ROTATION 5'-6" 7'-0" DIMENSIONS ARE FOR LARGEST GROVE FURNISHED HOOK BLOCK AND HEADACHE BALL, WITH ANTI-TWO BLOCK ACTIVATED. GROVE TMS875C 5

6 RATED LIFTING CAPACITIES IN POUNDS WITH 18,000 LB. COUNTERWEIGHT 36 FT. - FT. BOOM ON OUTRIGGERS FULLY EXTENDED - 3 #01 Ma Boom Length 36 * 1,000+ (68),0 96,0 78,7 (47) 59,0 (32.5) 109,0 104,0 91,0 (69) 75,0 59,7 (55) 47,0 (47) 38,5 (37.5) 28,4 (24.5) 84,200 79,8 73,0 (73) 59,0,000 (62.5) 42,0 36,9 () 28,4 (43) 23,0 (34.5) 19,4 (23) **56,4 56,4 56,4 56,4 48,0 41,0 (62.5) 36,0 29,0 24,6 (46.5) 20,0 (39.5) 17,0 (32) 14,0 (21) 56,0,9 43,0 (71) 38,0 33,0,0 25,5 (54) 21,0 (49) 18,4 (43.5) 15,8 (37.5) 13,6 () 11,6 (20) **47,8 41,000,2 31,0 (.5) 27,6 24,3 22,0 (59.5) 20,0 (55.5) 18,3 16,5 (46.5) 14,3 12,0 (.5) 10,0 (29) 9,4 (19),3 (79) 34,7,4 (73) 27,000 () 24,2 21,0 (63.5) 19,9 18,0 16,8 (53) 14,0 (49) 13,0 (44.5) 11,4 (39.5) 10,000 (34.5) 8,7 (28) 7,6 (18.5) **27,3 27,3 27,3 (75.5) 25,0 22,0 () 20,8 19, 17,5 (61) 16,200 15,0 (54.5) 13,0 (.5) 11,0 (47) 10,0 (43) 9,2 (38.5) 8,1 (33) 7,1 (27) 6,2 (18.5) Mimum boom angle (deg.) for dicated length (no load) 0 Maximum boom length (ft.) at 0 degree boom angle (no load) #LMI operatg code. Refer to LMI manual for structions. **This capacity is based on maximum boom angle. Boom Angle 0 Liftg Capacities On Outriggers Fully Extended - 3 At Zero Degree Boom Angle Ma Boom Length 36 * 27,0 (28.3) 16,200 (42.8) 11,3 (53.1) 9,1 (62.8) 7,410 (72.8) 6,0 (82.8) 4,9 (92.8) 4,0 (102.8) NOTE: ( ) Reference radii feet. A * ft. boom length is with ner-mid extended and outer-mid & fly retracted. +12 parts le required to lift this capacity (usg aux. boom nose). Refer to Operator's and Safety Handbook for reevg diagram. 6 GROVE TMS875C

7 31 FT FT. FOLDING BOOM EXTENSION WITH 18,000 LB. COUNTERWEIGHT ON OUTRIGGERS FULLY EXTENDED FT. LENGTH 56 FT. LENGTH #0521 #0522 #0523 #0541 #0542 #0543 *12,0 12,0 12,0 12,7 12,3 11,0 (.5) 10,9 10,0 9,9 9,4 9,0 (59) 8,6 8,2 (54) 7,0 7,5 (48.5) 7,0 (.5) 5,0 (38.5) 4,0 (.5) 3,0 (18.5) 8,3 8,020 (77.5) 7,7 7,3 7,1 6,8 6,6 6,4 6,2 (62.5) 6, 5,9 5,8 (54.5) 5,7 (51.5) 5,6 (48.5) 5, All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J-765 NOV ft. and 56 ft. foldg boom extension lengths may be used for sgle le liftg service only. 3. For ma boom lengths less than ft., rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. 4. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 5. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. *6,3 6,0 (79) 6,2 6,1 6, 6,0 6,0 6,0 6,0 6,0 (59) 6,0 () 8,0 (68) 7,6 7,220 6,8 6,5 6,1 (58) 5,7 (55.5) 5,0 4,510 (46) 4,0 () 3,1 (33.5) *4,7 4,6 4,4 4,3 4,1 4,0 3,9 () 3,8 3,7 3,6 (63.5) 3,5 (61) 3,420 3,320 3,2 () 2,320 (37.5) *3,7 3,7 3,720 3,0 3,0 3,0 (69) 3,0 3,0 3,4 (59) 1 2,4 (24.5) No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at 0 deg. boom angle A #LMI operatg code. Refer to LMI manual for operatg structions. *This capacity is based on maximum boom angle. GROVE TMS875C 7

8 RATED LIFTING CAPACITIES IN POUNDS WITH 8,0 LB. COUNTERWEIGHT 36 FT. - FT. BOOM ON OUTRIGGERS FULLY EXTENDED - 3 #0001 Ma Boom Length 36 * 1,000+ (68),0 96,0 72,000 (47) 54,4 (32.5) 109,0 104,0 91,0 (69) 71,8 54,3 (55) 42,0 (47) 32,0 (37.5) 24,0 (24.5) 84,200 79,8 73,0 (73) 59,0,000 (62.5) 42,0 32,0 () 25,4 (43) 20,3 (34.5) 16,0 (23) **56,4 56,4 56,4 56,4 48,0 41,0 (62.5) 33,0 26,0 21,200 (46.5) 17,2 (39.5) 14,1 (32) 11,0 (21) 56,0,9 43,0 (71) 38,0 33,0 27,4 22,1 (54) 18,1 (49) 15,0 (43.5) 12,0 (37.5) 10,5 () 8,8 (20) **47,8 41,000,2 31,0 (.5) 27,6 24,3 22,0 (59.5) 19, (55.5) 15,9 13,0 (46.5) 11,0 9,720 (.5) 8,0 (29) 7,0 (19),3 (79) 34,7,4 (73) 27,000 () 24,2 21,0 (63.5) 19,4 16,0 13,0 (53) 11,7 (49) 10,0 (44.5) 8,6 (39.5) 7,4 (34.5) 6,420 (28) 5,510 (18.5) **27,3 27,3 27,3 (75.5) 25,0 22,0 () 20,8 19, 16,0 (61) 14,1 12,1 (54.5) 10,4 (.5) 9,0 (47) 7,8 (43) 6,810 (38.5) 5,0 (33) 5, (27) 4,3 (18.5) Mimum boom angle (deg.) for dicated length (no load) 0 Maximum boom length (ft.) at 0 degree boom angle (no load) #LMI operatg code. Refer to LMI manual for structions. **This capacity is based on maximum boom angle. Boom Angle 0 Liftg Capacities On Outriggers Fully Extended - 3 At Zero Degree Boom Angle Ma Boom Length 36 * 27,0 (28.3) 16,200 (42.8) 11,3 (53.1) 9,1 (62.8) 7,410 (72.8) 6,0 (82.8) 4,9 (92.8) 4,010 (102.8) NOTE: ( ) Reference radii feet. A * ft. boom length is with ner-mid extended and outer-mid & fly retracted. +12 parts le required to lift this capacity (usg aux. boom nose). Refer to Operator's and Safety Handbook for reevg diagram. 8 GROVE TMS875C

9 31 FT FT. FOLDING BOOM EXTENSION WITH 8,0 LB. COUNTERWEIGHT ON OUTRIGGERS FULLY EXTENDED FT. LENGTH 56 FT. LENGTH #0021 #0022 #0023 #0041 #0042 #0043 *12,0 12,0 12,0 12,7 12,3 11,0 (.5) 10,9 10,0 9,9 9,4 9,0 (59) 8,6 7,910 (54) 6,9 6, (48.5) 5,3 (.5) 4, (38.5) 3,0 (.5) 2,2 (18.5) 8,3 8,020 (77.5) 7,7 7,3 7,1 6,8 6,6 6,4 6,2 (62.5) 6, 5,9 5,8 (54.5) 5,7 (51.5) 5,6 (48.5) 4,3 *6,3 1. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J-765 NOV ft. and 56 ft. foldg boom extension lengths may be used for sgle le liftg service only. 3. For ma boom lengths less than ft., rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. 4. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 5. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. 6,0 (79) 6,2 6,1 6, 6,0 6,0 6,0 6,0 6,0 (59) 6,0 () 8,0 (68) 7,6 7,220 6,8 6,5 6,1 (58) 5,7 (55.5) 4,820 3,7 (46) 2,920 () 2,200 (33.5) *4,7 4,6 4,4 4,3 4,1 4,0 3,9 () 3,8 3,7 3,6 (63.5) 3,5 (61) 3,420 3,320 3,2 () 2,320 (37.5) *3,7 3,7 3,720 3,0 3,0 3,0 (69) 3,0 3,0 3,4 (59) 1 1,5 (24.5) No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at 0 deg. boom angle A #LMI operatg code. Refer to LMI manual for operatg structions. *This capacity is based on maximum boom angle. GROVE TMS875C 9

10 Workg Range -125 ft. ( m) - ft. ( m) 18,000 lbs. (8165 kg) % 3 FEET (BOOM DEFLECTION NOT SHOWN) HEIGHT FROM THE GROUND IN FEET BOOM & EXTENSION LENGHT IN FEET MAX. BOOM ANGLE OPERATING RADIUS IN FEET FROM AXIS OF ROTATION AXIS OF ROTATION 5'-6" 7'-0" DIMENSIONS ARE FOR LARGEST GROVE FURNISHED HOOK BLOCK AND HEADACHE BALL, WITH ANTI-TWO BLOCK ACTIVATED. 10 GROVE TMS875C

11 RATED LIFTING CAPACITIES IN POUNDS WITH 18,000 LB. COUNTERWEIGHT FT FT. BOOM ON OUTRIGGERS FULLY EXTENDED - 3 #0001 Ma Boom Length ,000 () 123,0 108,000 84,200 (52.5) 64,0,7 (26) 105, ,000 () 104,000 83,6 (58) 63,5 (49.5),3 (39.5),3 (26) 94,0 88,2 (.5) 76,3 62,8 49,0 39,7 (44.5) 31,2 (.5) 24,2 (23) 71,0,0 56, 48,2 (59) 39,2 (53.5) 31,2 25,0 (.5) 20,000 (32.5) 12,0 (21) 55,2 47,9 41,9 36,2 (59.5) 31,0 (55) 25,3 (49.5) 20,7 (44) 17,0 (38) 14,1 () 9,420 (19.5) 48,1 41,0 36,0 32,0 29,000 25,7 (55.5) 21,7 (51.5) 18, (46.5) 15, 12,6 (.5) 10,0 (28.5) 7,2 (18.5) 38,000 33,0 (.5) 29,5 26,4 (63.5) 23,8 21,0 19,000 (52.5) 16,000 (48.5) 13,5 (44) 11,4 (39) 9,0 (33.5) 8,1 (27) 5,620 (17.5) 33,3 (75.5),7 27,0 24,4 22,000 (63.5) 19,8 (.5) 17,9 (57) 16,0 (53.5) 14,0 () 12,000 (46) 10,2 (42) 8,7 (37.5) 7,4 (32) 6,2 (25.5) 4,410 (16.5) 24,5 21,0 19,3 17,4 15,0 14,5 (61) 13,2 (58) 12,0 (55) 11,0 (51.5) 10,0 (48) 9,2 (44.5) 7,9 (.5) 6,810 (36) 5,0 (31) 4,8 (25) 3,0 (16.5) *23,0 21,0 20,0 18,0 (69) 17,0 15,0 14,1 13,000 11,8 (55.5) 10,7 (52.5) 9,6 (49.5) 8,4 (46.5) 7,320 6,0 (39) 5,3 (34.5) 3,820 (24) Mimum boom angle (deg.) for dicated length (no load) 0 Maximum boom length (ft. ) at 0 degree boom angle (no load) 125 *Based on maximum obtaable boom angle. #LMI operatg code. Refer to LMI manual for operatg structions. +12 parts le required to lift this capacity (usg aux. boom nose). Refer to Operator's and Safety Handbook for reevg diagram. Liftg Capacities at Zero Degree Boom Angle Boom Angle 0 Ma Boom Length ,0 (32.3) 18,2 (37.8) Note: ( ) Reference radii are feet. 12,200 (47.8) 7,9 (57.8) 5,720 (67.8) 4,320 (77.8) 3,210 (87.8) 2,3 (97.8) 4,5 () 1,5 (107.8) A GROVE TMS875C 11

12 FT. - FT. TELE. EXTENSION WITH 18,000 LB. COUNTERWEIGHT ON OUTRIGGERS FULLY EXTENDED ** ft. LENGTH ft. LENGTH #0021 #0023 #0041 # *12,0 11,0 (75.5) 10,0 10,0 9,7 9,2 8,810 8,0 (63.5) 8,0 7,6 (59) 7,3 (57) 6,710 (54.5) 5,820 (52.5) 5,010 () 4,2 3,6 (44.5) 3,0 2,0 (38.5) 2,000 () 1,5 (31.5) 1, (27) *7,0 7,2 7, 6,9 (.5) 6,8 (68) 6,7 6,6 6,5 6,4 (59) 5,7 5,1 (54) 4,5 (51.5) 4,0 (48.5) 3,5 (.5) 2,9 2,410 (39) *6,0 6,320 6,000 5,6 5,2 () 4,0 4,6 4,3 4, 3,0 (61) 3,6 (59.5) 3,4 3,3 (55.5) 3,220 (53.5) 3, 2,9 (49) 2,7 (47) 2,4 (44.5) 2, (42) 1,820 (39) 1,5 (36.5) 1,2 (33.5) *4,000 3,0 3,0 3,3 (71) 3,2 (69) 3,210 3,1 3, 3,0 (61) 3,010 2,9 2,7 (54) 2,0 (51.5) 2,0 (48.5) 1,7 (46) 1,420 1, (39.5) A *This capacity is based upon maximum boom angle. ** ft. tele. length is also applicable to ft. fixed length, however, the LMI codes will change to #0051 and #0053 for the 2 and offset respectively. #LMI operatg code. Refer to LMI manual for structions. 1. All capacities above the bold le are based on structural strength of boom extension. 2. ft. and ft. boom extension lengths may be used for sgle le liftg service only. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers fully extended and vertical jacks set only. 6. FT. FIXED OR TELE. TABLE BOOM EXTENSION WARNING: For ma boom length greater than 115 ft. with ft. fixed or tele. boom extension workg position, the boom angle must not be less than 24 sce loss of stability will occur causg a tippg condition. The boom angle is not restricted for ma boom length equal to or less than 115 ft. This warng also applies for boom extension erection purposes. FT. TELE. TABLE BOOM EXTENSION WARNING: For ma boom length greater than 105 ft. with ft. tele. boom extension workg position, the boom angle must not be less than sce loss of stability will occur causg a tippg condition. The boom angle is not restricted for ma boom length equal to or less than 105 ft. This warng also applies for boom extension erection purposes. 12 GROVE TMS875C

13 RATED LIFTING CAPACITIES IN POUNDS WITH 8,0 LB. COUNTERWEIGHT FT FT. BOOM ON OUTRIGGERS FULLY EXTENDED - 3 #0201 Ma Boom Length ,000 () 123,0 108,000 77,0 (52.5) 58,6, (26) 105, ,000 () 104,000 76,0 (58) 58,1 (49.5) 44,6 (39.5) 34,4 (26) 94,0 88,2 (.5) 76,1 57,0 43,9 33,6 (44.5) 26, (.5) 20,0 (23) 71,0,0 56, 42,9 (59) 32,2 (53.5) 24,8 19,0 (.5) 15,4 (32.5) 11,0 (21) 55,2 47,9 41,9 32,0 (59.5) 25,3 (55) 19,8 (49.5) 15,0 (44) 12,0 (38) 10,1 () 8,1 (19.5) 48,1 41,0 36,0 32,0 26,5 20,9 (55.5) 16,8 (51.5) 13,6 (46.5) 11,1 9, (.5) 7,3 (28.5) 5,920 (18.5) 38,000 33,0 (.5) 29,5 26,4 (63.5) 22,0 17,8 14,6 (52.5) 12,0 (48.5) 10,000 (44) 8,0 (39) 6,810 (33.5) 5,5 (27) 4,4 (17.5) 33,3 (75.5),7 27,0 24,4 22,000 (63.5) 18,4 (.5) 15,200 (57) 12,0 (53.5) 10,0 () 8,7 (46) 7,2 (42) 6,0 (37.5) 4,910 (32) 3,9 (25.5) 3,0 (16.5) 24,5 21,0 19,3 17,4 15,0 14,5 (61) 13, (58) 10,9 (55) 9,210 (51.5) 7,720 (48) 6,4 (44.5) 5,3 (.5) 4,3 (36) 3,510 (31) 2,7 (25) 2,0 (16.5) *23,0 21,0 20,0 18,0 (69) 17,0 15,0 13,0 11,4 9,6 (55.5) 8,1 (52.5) 6,8 (49.5) 5,7 (46.5) 4,7 3,910 (39) 3, (34.5) 1,0 (24) Mimum boom angle (deg.) for dicated length (no load) 0 Maximum boom length (ft. ) at 0 degree boom angle (no load) 125 *Based on maximum obtaable boom angle. #LMI operatg code. Refer to LMI manual for operatg structions. +12 parts le required to lift this capacity (usg aux. boom nose). Refer to Operator's and Safety Handbook for reevg diagram. Liftg Capacities at Zero Degree Boom Angle Boom Angle 0 Ma Boom Length ,0 (32.3) 18,2 (37.8) Note: ( ) Reference radii are feet. 12,200 (47.8) 7,9 (57.8) 5,720 (67.8) 4,320 (77.8) 3,210 (87.8) 2,3 (97.8) 2,4 () 1,5 (107.8) A GROVE TMS875C 13

14 FT. - FT. TELE. BOOM EXTENSION WITH 8,0 LB. COUNTERWEIGHT ON OUTRIGGERS FULLY EXTENDED ** ft. LENGTH ft. LENGTH #0221 #0223 #0241 # *12,0 11,0 (75.5) 10,0 10,0 9,7 9,2 8,810 8,0 (63.5) 7,3 6,2 (59) 5,2 (57) 4,3 (54.5) 3,0 (52.5) 2,910 () 2,2 1,720 (44.5) 1,210 *7,0 7,2 7, 6,9 (.5) 6,8 (68) 6,7 6,6 6,3 5,3 (59) 4,510 3,710 (54) 3,000 (51.5) 2,3 (48.5) 1,7 (.5) 1,2 *6,0 6,320 6,000 5,6 5,2 () 4,0 4,6 4,3 4, 3,0 (61) 3,6 (59.5) 3,4 3,3 (55.5) 2,9 (53.5) 2,0 2,0 (49) 1,6 (47) 1,2 (44.5) *4,000 3,0 3,0 3,3 (71) 3,2 (69) 3,210 3,1 3, 3,0 (61) 3,010 2,9 2,610 (54) 2, (51.5) 1,6 (48.5) 1,1 (46) A *This capacity is based upon maximum boom angle. ** ft. tele. length is also applicable to ft. fixed length, however, the LMI codes will change to #0251 and #0253 for the 2 and offset respectively. #LMI operatg code. Refer to LMI manual for structions. 1. All capacities above the bold le are based on structural strength of boom extension. 2. ft. and ft. boom extension lengths may be used for sgle le liftg service only. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers fully extended and vertical jacks set only. 6. FT. FIXED OR TELE. TABLE BOOM EXTENSION WARNING: For ma boom length greater than 85 ft. with ft. fixed or tele. boom extension workg position, the boom angle must not be less than 39 sce loss of stability will occur causg a tippg condition. The boom angle is not restricted for ma boom length equal to or less than 85 ft. This warng also applies for boom extension erection purposes. FT. TELE. TABLE BOOM EXTENSION WARNING: For ma boom length greater than 85 ft. with ft. tele. boom extension workg position, the boom angle must not be less than 42 sce loss of stability will occur causg a tippg condition. The boom angle is not restricted for ma boom length equal to or less than 85 ft. This warng also applies for boom extension erection purposes. 14 GROVE TMS875C

15 Workg Range -138 ft. ( m) ft. ( m) 18,000 lbs. (8165 kg) % 3 FEET 2 (BOOM DEFLECTION NOT SHOWN) HEIGHT FROM THE GROUND IN FEET BOOM & EXTENSION LENGHT IN FEET MAX. BOOM ANGLE OPERATING RADIUS IN FEET FROM AXIS OF ROTATION AXIS OF ROTATION 5'-6" 7'-0" DIMENSIONS ARE FOR LARGEST GROVE FURNISHED HOOK BLOCK AND HEADACHE BALL, WITH ANTI-TWO BLOCK ACTIVATED. GROVE TMS875C 15

16 RATED LIFTING CAPACITIES IN POUNDS WITH 18,000 LB. COUNTERWEIGHT FT FT. BOOM (MODE A) ON OUTRIGGERS FULLY EXTENDED - 3 #01 Ma Boom Length ,000,000 95,0 77,2 (44.5) 58,0 (29.5) 42,0 (77.5) 42,000 (75.5) 36,5 29,0 24,3 20,0 17,4 () 15,0 (43) 13, () 11,4 (24.5) *32, 32, 32, 31,3 26,4 22,0 19, 16,0 (53.5) 14,4 (48.5) 12,7 10,0 (28) *31,8 31,8 28,8 25,0 21,5 (68) 18,0 16,000 14,000 12,3 9,7 7,8 () *21,3 21,3 (77.5) 20,8 18,6 16,0 15,0 13,6 12, 9,5 7,710 6,2 (32) 4,0 (15.5) 19,000 18,1 17,0 16,4 15,6 (69) 14,1 12,0 10,1 (57) () 6,7 5,5 (33.5) 4,010 (21) *19,000 18,0 17,6 17,000 16,3 15,0 13,0 11,0 9, (55) 7,3 (49.5) 5,0 (43) 4,000 (36) 2,7 (27) 1 1,720 (9.5) Mimum boom angle (deg.) for dicated length (no load) 0 9 Maximum boom length (ft.) at 0 degree boom angle (no load) #LMI operatg code. Refer to LMI manual for structions. *This capacity is based on maximum boom angle. +12 parts le required to lift this capacity (usg aux. boom nose). Refer to Operator's and Safety Handbook for reevg diagram. Liftg Capacities On Outriggers Fully Extended - 3 At Zero Degree Boom Angle Boom Angle 0 Ma Boom Length ,0 (28.2) 10,1 (53.8) 6,2 (66.6) 3,420 (79.4) 2,4 (92.2) 1,6 (105) A NOTE: ( ) Reference radii feet. Ext. % Inner-mid Center-mid 0 Outer-mid Fly GROVE TMS875C

17 RATED LIFTING CAPACITIES IN POUNDS WITH 18,000 LB. COUNTERWEIGHT FT FT. BOOM (MODE B) 10 +1,000 12, , ,2 (44.5) 25 58,0 (29.5) ON OUTRIGGERS FULLY EXTENDED - 3 #01 Ma Boom Length , 79, 79, (),8 58,200 (58),8 37, (43.5) 27,0 (34.5) 22,000 (21.5) 78,4 (77.5) 77,0 (75.5) 69,8 59,8 52,200 46,200 37,0 () 27,0 (43) 22,4 () 18,0 (24.5) *57,0 57,0 51,6 44,3 38,7 34,200 29,0 25,1 (53.5) 21,0 (48.5) 18,5 12,0 (28) *43,0 43,0 39,5 33,0 29,200 (68) 25,0 22,0 20,000 17,0 12,0 8,8 () *32, 32, (77.5) 32,,200 26,0 23,4 20,4 17,0 14,000 10,1 7,1 (32) 4,0 (15.5),0,0 27,3 24,0 21,0 (69) 19,2 16,0 13,2 (57) 10,0 () 8,2 5,8 (33.5) 4,010 (21) *20,1 20,1 (79) 19, 18, 17,2 16,4 (69) 15,7 13, 10,0 8,6 (49.5) 6,0 (43) 4,8 () 3,3 (24.5) *19,000 18,0 17,6 17,000 16,3 15,0 13,0 11,0 9, (55) 7,3 (49.5) 2,7 (27) 1 1,720 (9.5) Mimum boom angle (deg.) for dicated length (no load) 9 Maximum boom length (ft.) at 0 degree boom angle (no load) 125 #LMI operatg code. Refer to LMI manual for structions. *This capacity is based on maximum boom angle. +12 parts le required to lift this capacity (usg aux. boom nose). Refer to Operator's and Safety Handbook for reevg diagram. Boom Angle 0 26,0 (28.2) Liftg Capacities On Outriggers Fully Extended - 3 At Zero Degree Boom Angle Ma Boom Length ,0 (47.4) 10,1 (53.8) 6,2 (66.6) 3,420 (79.4) 2,4 (92.2) 1,6 (105) 1,0 (117.8) NOTE: ( ) Reference radii feet. A Ext. % Inner-mid 0 75 Center-mid Outer-mid Fly ,0 (43) 4,000 (36) GROVE TMS875C 17

18 31 FT FT. FOLDING BOOM EXTENSION WITH 18,000 LB. COUNTERWEIGHT USING 125 FT. MAIN BOOM LENGTH ON OUTRIGGERS FULLY EXTENDED FT. LENGTH 56 FT. LENGTH #0521 #0522 #0523 #0541 #0542 #0543 *11,0 11,0 11,0 11,0 11,000 10,0 () 9,220 8,4 7,3 6,020 (53) 4,510 3,2 2,2 (34.5) 1,3 (26) *10,000 9,0 8,7 7,9 7,3 6,0 6,5 6,2 (55) 5,0 () 3,6 (44) 2,5 (36.5) *8,000 6,810 6,4 6,0 (.5) 6,3 6,3 6,320 5,2 No Load Stability Data 6,9 6,7 6,620 6,2 5,9 (71) 5,6 5,2 4,9 (.5) 4,6 4,0 3,020 2,1 1,3 (36.5) *4,0 4,5 4,2 (73) 3,8 3,0 3,4 3,2 3, (52.5) 2,7 1,8 (41) *3,0 3,520 3,0 3,2 3,1 3, (59.5) 3,0 (54) Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at 0 deg. boom angle. A #LMI operatg code. Refer to LMI manual for operatg structions. *This capacity is based on maximum boom angle. 1. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J-765 NOV ft. and 56 ft. foldg boom extension lengths may be used for sgle le liftg service only. 3. For ma boom lengths less than 125 ft. with the boom extension erected, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. 4. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 5. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. 18 GROVE TMS875C

19 31 FT FT. FOLDING BOOM EXTENSION WITH 18,000 LB. COUNTERWEIGHT USING 138 FT. MAIN BOOM ON OUTRIGGERS FULLY EXTENDED FT. LENGTH 56 FT. LENGTH #0521 #0522 #0523 #0541 #0542 #0543 9,0 9,0 9,0 9,0 9, 8,4 7,5 6,9 (.5) 6,3 4,820 3,5 (47) 2,5 1,6 (.5) *8,7 7,4 7,0 6,720 6,3 (68) 6,0 5,820 5,0 (55.5) 4,0 (.5) 2,910 () 1,9 (38.5) *7,0 6,7 6,4 6,3 6,2 6,220 (61) 5,6 4,0 *5,0 5,0 5,0 5, (75.5) 4,0 4,0 4,0 4,0 (63.5) 4, (59.5) 3,0 3,1 2,0 1,5 *4,6 4,4 4,220 4, (71) 3,810 3,0 3,0 (.5) 3,1 2,9 (51.5) 2, (46.5) *3,0 3,0 (77.5) 3,0 3,0 (.5) 3,200 3, 3,000 2,0 (53.5) 1 1,0 (41) No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at deg. boom angle A #LMI operatg code. Refer to LMI manual for operatg structions. *This capacity is based on maximum boom angle. 1. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J-765 NOV ft. and 56 ft. foldg boom extension lengths may be used for sgle le liftg service only. 3. For ma boom lengths between 125 ft. and fully extended with the boom extension erected, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. 4. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 5. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. GROVE TMS875C 19

20 31 FT FT. LUFFING FOLDING BOOM EXTENSION WITH 18,000 LB. COUNTERWEIGHT USING 125 FT. MAIN BOOM LENGTH ON OUTRIGGERS FULLY EXTENDED - 3 (reference) FT. LENGTH 56 FT. LENGTH #5910 #5911 #5912 #5920 #5921 #5922 *11,000 11,000 11,000 11,000 11,000 10,0 () 9,220 8,4 7,3 6,000 (53) 4,4 3,210 2,1 (34.5) 1,2 (26) *10,000 9,0 8,7 7,9 7,3 6,0 6,5 6,2 (55) 4,8 () 3,5 (44) 2,420 (36.5) #LMI operatg code, for reference only (does not require put - automatically displayed). Refer to LMI manual for operatg structions. * This capacity is based on maximum boom angle. 1. Capacities are based on ma boom angles conjunction with extension offset angle. Radii are for 125' ma boom length only. 2. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J ft. and 56 ft. luffg foldg boom extension lengths may be used for sgle le liftg service only. 4. For ma boom lengths less than 125 ft. with the boom extension erected, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. For extension offset angles not shown, use ratg of next greater offset angle. 5. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 6. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 7. Capacities listed are with outriggers properly extended and vertical jacks set only. *8,000 6,810 6,4 6,0 (.5) 6,3 6,3 6,320 4,5 6,4 6,4 6,4 6,2 5,9 (71) 5,6 5,2 4,9 (.5) 4,6 4,0 3,020 2,1 1,3 (36.5) *4,0 4,5 4,2 (73) 3,8 3,0 3,4 3,2 3, (52.5) 2,7 1,8 (41) *3,0 3,520 3,0 3,2 3,1 3, (59.5) 3,0 (54) No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at 0 boom angle A GROVE TMS875C

21 31 FT FT. LUFFING FOLDING BOOM EXTENSION WITH 18,000 LB. COUNTERWEIGHT USING 138 FT. MAIN BOOM ON OUTRIGGERS FULLY EXTENDED - 3 (reference) FT. LENGTH 56 FT. LENGTH #5910 #5911 #5912 #5920 #5921 #5922 9,0 9,0 9,0 9,0 9, 8,4 7,5 6,9 (.5) 6,2 4,7 3,5 (47) 2,5 1,6 (.5) *8,7 7,4 7,0 6,720 6,3 (68) 6,0 5,820 5,3 (55.5) 3,920 (.5) 2,7 () 1,7 (38.5) *7,0 6,7 6,4 6,3 6,1 5,8 (61) 5,4 3,9 *5,0 5,0 5,0 5, (75.5) 4,0 4,0 4,0 4,0 (63.5) 4, (59.5) 3,0 3,1 2,0 1,5 *4,6 4,4 4,220 4, (71) 3,810 3,0 3,0 (.5) 3,1 2,9 (51.5) 2, (46.5) *3,0 3,0 (77.5) 3,0 3,0 (.5) 3,200 3, 3,000 2,0 (53.5) 1 1,0 (41) No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at boom angle A #LMI operatg code, for reference only (does not require put - automatically displayed). Refer to LMI manual for operatg structions. *This capacity is based on maximum boom angle. 1. Capacities are based on ma boom angles conjunction with extension offset angle. Radii are for 138' ma boom length only. 2. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J ft. and 56 ft. luffg foldg boom extension lengths may be used for sgle le liftg service only. 4. For ma boom lengths between125 ft. and fully extended with the boom extension erected, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. For extension offset angles not shown, use ratg of next greater offset angle. 5. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 6. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 7. Capacities listed are with outriggers properly extended and vertical jacks set only. GROVE TMS875C 21

22 RATED LIFTING CAPACITIES IN POUNDS WITH 8,0 LB. COUNTERWEIGHT FT FT. BOOM (MODE A) ON OUTRIGGERS FULLY EXTENDED - 3 #0001 Ma Boom Length ,000,000 95,0,0 (44.5) 53,1 (29.5) 42,0 (77.5) 42,000 (75.5) 36,5 29,0 24,3 20,0 17,4 () 15,0 (43) 13, () 11,4 (24.5) *32, 32, 32, 31,3 26,4 22,0 19, 16,0 (53.5) 14,4 (48.5) 12,7 10,0 (28) *31,8 31,8 28,8 25,0 21,5 (68) 18,0 16,000 14,000 12,3 9,7 7,8 () *21,3 21,3 (77.5) 20,8 18,6 16,0 15,0 13,6 12, 9,5 7,710 6,2 (32) 4,0 (15.5) 19,000 18,1 17,0 16,4 15,6 (69) 14,1 12,0 10,1 (57) () 6,7 5,5 (33.5) 4,010 (21) *19,000 18,0 17,6 17,000 16,3 15,0 13,0 10,200 7,4 (55) 5,3 (49.5) 3,7 (43) 2,510 (36) 1,4 (27) Mimum boom angle (deg.) for dicated length (no load) 0 10 Maximum boom length (ft.) at 0 degree boom angle (no load) 112 #LMI operatg code. Refer to LMI manual for structions. *This capacity is based on maximum boom angle. +12 parts le required to lift this capacity (usg aux. boom nose). Refer to Operator's and Safety Handbook for reevg diagram. Liftg Capacities On Outriggers Fully Extended - 3 At Zero Degree Boom Angle Boom Angle 0 Ma Boom Length ,0 (28.2) 10,1 (53.8) 6,2 (66.6) 3,420 (79.4) 2,4 (92.2) 1,6 (105) A NOTE: ( ) Reference radii feet. Ext. % Inner-mid Center-mid 0 Outer-mid Fly GROVE TMS875C

23 RATED LIFTING CAPACITIES IN POUNDS WITH 8,0 LB. COUNTERWEIGHT FT FT. BOOM (MODE B) ON OUTRIGGERS FULLY EXTENDED #0001 Ma Boom Length ,000,000 95,0,0 (44.5) 53,1 (29.5) 79, 79, 79, (),0 52,8 (58) 41,0 31,8 (43.5) 24,0 (34.5) 19,5 (21.5) 78,4 (77.5) 77,0 (75.5) 69,8 59,8 52,200 41,0 31,9 () 24,7 (43) 19,5 () 15,0 (24.5) *57,0 57,0 51,6 44,3 38,7 34,200 29,0 24,0 (53.5) 19,7 (48.5) 15,0 9,4 (28) *43,0 43,0 39,5 33,0 29,200 (68) 25,0 22,0 19,0 15,3 9,7 6,020 () *32, 32, (77.5) 32,,200 26,0 23,4 20,4 16,5 10,0 7,0 4,3 (32) 2,420 (15.5),0,0 27,3 24,0 21,0 (69) 19,2 16,0 11,0 (57) 8,0 () 5,3 3,3 (33.5) 1,8 (21) *20,1 20,1 (79) 19, 18, 17,2 16,4 (69) 15,7 13,000 9,1 6,0 (49.5) 4,3 (43) 2,0 () 1,5 (24.5) *19,000 18,0 17,6 17,000 16,3 15,0 13,0 10,200 7,4 (55) 5,3 (49.5) 1,4 (27) Mimum boom angle (deg.) for dicated length (no load) 5 10 Maximum boom length (ft.) at 0 degree boom angle (no load) 112 #LMI operatg code. Refer to LMI manual for structions. *This capacity is based on maximum boom angle. +12 parts le required to lift this capacity (usg aux. boom nose). Refer to Operator's and Safety Handbook for reevg diagram. Boom Angle 0 Liftg Capacities On Outriggers Fully Extended - 3 At Zero Degree Boom Angle Ma Boom Length ,0 (28.2) 12,0 (47.4) 10,1 (53.8) 6,2 (66.6) 3,420 (79.4) 2,0 (92.2) 1,200 (105) NOTE: ( ) Reference radii feet. A Ext. % Inner-mid 0 75 Center-mid Outer-mid Fly ,7 (43) 2,510 (36) GROVE TMS875C 23

24 31 FT FT. FOLDING BOOM EXTENSION WITH 8,0 LB. COUNTERWEIGHT USING 125 FT. MAIN BOOM LENGTH ON OUTRIGGERS FULLY EXTENDED FT. LENGTH 56 FT. LENGTH #0021 #0022 #0023 #0041 #0042 #0043 *11,0 11,0 11,0 11,0 11,000 10,0 () 9,220 7,910 5,7 4,1 (53) 2,8 1,7 *10,000 9,0 8,7 7,9 7,3 6,0 6,3 4,5 (55) 3,0 () 1,0 (44) 6,9 1. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J-765 NOV ft. and 56 ft. foldg boom extension lengths may be used for sgle le liftg service only. 3. For ma boom lengths less than 125 ft. with the boom extension erected, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. 4. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 5. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. *8,000 6,810 6,4 6,0 (.5) 6,3 6,3 5, 3,4 6,7 6,620 6,2 5,9 (71) 5,6 5,2 4,9 (.5) 4,0 2,8 1,8 1,020 *4,0 4,5 4,2 (73) 3,8 3,0 3,4 3,2 2,3 (52.5) 1,4 *3,0 3,520 3,0 3,2 3,1 3, (59.5) 2,8 (54) No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at 0 deg. boom angle. A #LMI operatg code. Refer to LMI manual for operatg structions. *This capacity is based on maximum boom angle. 24 GROVE TMS875C

25 31 FT FT. FOLDING BOOM EXTENSION WITH 8,0 LB. COUNTERWEIGHT USING 138 FT. MAIN BOOM ON OUTRIGGERS FULLY EXTENDED FT. LENGTH 56 FT. LENGTH #0021 #0022 #0023 #0041 #0042 #0043 9,0 9,0 9,0 9,0 9, 8,4 7,5 6,200 (.5) 4,5 3,200 2, (47) 1,220 *8,7 7,4 7,0 6,720 6,3 (68) 6,0 5,3 3,8 (55.5) 2,6 (.5) 1,6 () *7,0 *5,0 5,0 1. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J-765 NOV ft. and 56 ft. foldg boom extension lengths may be used for sgle le liftg service only. 3. For ma boom lengths between 125 ft. and fully extended with the boom extension erected, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. 4. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 5. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. 6,7 6,4 6,3 6,2 5,5 (61) 3,9 2,6 5,0 5, (75.5) 4,0 4,0 4,0 4,0 (63.5) 4, (59.5) 3, 2,1 1,320 *4,6 4,4 4,220 4, (71) 3,810 3,0 3,0 (.5) 2,6 1,6 (51.5) *3,0 3,0 (77.5) 3,0 3,0 (.5) 3,200 3, 3,000 1,920 (53.5) No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at 0 deg. boom angle A A #LMI operatg code. Refer to LMI manual for operatg structions. *This capacity is based on maximum boom angle. GROVE TMS875C 25

26 31 FT FT. LUFFING FOLDING BOOM EXTENSION WITH 8,0 LB. COUNTERWEIGHT USING 125 FT. MAIN BOOM LENGTH ON OUTRIGGERS FULLY EXTENDED - 3 (reference) 1 31 FT. LENGTH 56 FT. LENGTH #0910 #0911 #0912 #0920 #0921 #0922 *11,000 11,000 11,000 11,000 11,000 10,0 () 9,220 7,7 5,6 3,9 (53) 2,5 1,4 *10,000 9,0 8,7 7,9 7,3 6,0 6,1 4,3 (55) 2,9 () 1,7 (44) *8,000 6,810 6,4 6,0 (.5) 1. Capacities are based on ma boom angles conjunction with extension offset angle. Radii are for 125' ma boom length only. 2. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J ft. and 56 ft. luffg foldg boom extension lengths may be used for sgle le liftg service only. 4. For ma boom lengths less than 125 ft. with the boom extension erected, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. For extension offset angles not shown, use ratg of next greater offset angle. 5. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 6. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 7. Capacities listed are with outriggers properly extended and vertical jacks set only. 6,3 6,320 4,3 2,0 6,4 6,4 6,4 6,2 5,9 (71) 5,6 5,2 4,9 (.5) 3,6 2,0 1,5 *4,0 4,5 4,2 (73) 3,8 3,0 3,4 3,2 2,0 (52.5) *3,0 3,520 3,0 3,2 3,1 3, (59.5) 2,5 (54) 1 1,2 No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at 0 deg boom angle. A #LMI operatg code, for reference only (does not require put - automatically displayed). Refer to LMI manual for operatg structions. * This capacity is based on maximum boom angle. 26 GROVE TMS875C

27 31 FT FT. LUFFING FOLDING BOOM EXTENSION WITH 8,0 LB. COUNTERWEIGHT USING 138 FT. MAIN BOOM ON OUTRIGGERS FULLY EXTENDED - 3 (reference) FT. LENGTH 56 FT. LENGTH #0910 #0911 #0912 #0920 #0921 #0922 9,0 9,0 9,0 9,0 9, 8,4 7,5 5,0 (.5) 4,020 2,7 1,7 (47) *8,7 7,4 7,0 6,720 6,3 (68) 6,0 5,0 3,4 (55.5) 2,200 (.5) 1,1 () 1. Capacities are based on ma boom angle conjunction with extension offset angle. Radii are for 138 ft. ma boom length only. 2. All capacities above the bold le are based on structural strength of boom extension and do not exceed 85% of tippg loads, accordance with SAE J ft. and 56 ft. luffg foldg boom extension lengths may be used for sgle le liftg service only. 4. For ma boom lengths between 125 ft. and fully extended with the boom extension erected, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is set up. For boom angles not shown, use ratg of the next lower boom angle. For extension offset angles not shown, use ratg of next greater offset angle. 5. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 6. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 7. Capacities listed are with outriggers properly extended and vertical jacks set only. *7,0 6,7 6,4 6,3 6,1 5,220 (61) 3,5 2,2 *5,0 5,0 5,0 5, (75.5) 4,0 4,0 4,0 4,0 (63.5) 3,9 (59.5) 2,820 1,7 *4,6 4,4 4,220 4, (71) 3,810 3,0 3,0 (.5) 2,5 1,0 (51.5) *3,0 3,0 (77.5) 3,0 3,0 (.5) 3,200 3, 2,9 1,8 (53.5) No Load Stability Data Mimum boom angle (deg.) for dicated length Maximum boom length (ft.) at 0 deg boom angle A #LMI operatg code, for reference only (does not require put - automatically displayed). Refer to LMI manual for operatg structions. *This capacity is based on maximum boom angle. GROVE TMS875C 27

28 Features and Benefits Optional luffg swgaway for five section boom offers ability to offset air under load Standard front and rear air ride suspension provides comfortable ride at max speed of 65 mph Electronically controlled Cumms six cylder, turbo charged, 0 bhp diesel -- highest 75 ton class Both carrier and operator s cab constructed from galvannealed metal and fished with Imron 00 to improve longevity Hot water cab heater/defrosters also standard both cabs Constant improvement and engeerg progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may clude optional equipment and accessories and may not clude all standard equipment. GROVE and GROVE LOGO are registered trademarks of GROVE the U.S. and/or other countries. Copyright 2000 GROVE. All rights reserved. Grove Worldwide - World Headquarters 1565 Buchanan Trail East P.O. Box 21 Shady Grove, Pennsylvania , U.S.A. Tel: (717) Fax: (717) Form No.: TMS875C Series Part No.: M Prted U.S.A.