TR-500XL Ton Capacity (45.4 Metric Tons) HYDRAULIC ROUGH TERRAIN CRANE DIMENSIONS. MIN. 34' 9-1/4" (10.6m) MAX. 110' 6-3/4" (33.

Transcription

1 TR-500XL-3 50 Ton Capacity (45.4 Metric Tons) HYDRAULIC ROUGH TERRAIN CRANE DIMENSIONS MIN. 34' 9-1/4" (10.6m) MAX. 110' 6-3/4" (33.7m) 6' (1.83m) 12' 4 (3.76m) 12' 2" (3.71m) 11' 6-1/4" (3.51m) 12' 1-1/4" (3.69m) 6' 9-3/4" (2.075m) 6' 1-7/8" (1.875m) 16' 8-3/4" (5.1m) 12' 11-1/2" (3.95m) 7' 4-3/8 (2.245m) 26' 8" (8.13m) 43' 4-3/4" (13.23m) Note: Dimension is with boom angle at -1.5 degree. GENERAL DIMENSIONS (29.5 x 25 Tires) Feet Meters Turning radius: 4 wheel steer 21' 11-3/4" wheel steer 39' 1/2" 11.9 Tail swing of counterweight 13' 6-1/4" ' 2-1/2" (2.502m) 10' 10-1/2" (3.315m) MID. 18' 1/2" (5.5m) MID. 21' 11-3/4" (6.7m) MAX. 23' 7-1/2" (7.2m) Specifications are subject to change without notice.

2 CRANE SPECIFICATIONS BOOM Four section full power partially synchronized telescoping boom of hexagonal box construction 34.8'~110.6' (10.6m~33.7m) with five sheaves,17-1/4" (0.438m) root diameter, at boom head. The synchronization system consists of two telescope cylinders fitted with holding valves, an extension cable and retraction cable. Two easily removable wire rope guards, rope dead end provided on right side of boom head. Boom telescope sections are supported by wear pads both vertically and horizontally. BOOM ELEVATION - By a double acting hydraulic cylinder with holding valve. Elevation -1.5 o ~8, combination controls for hand or foot operation. Boom angle indicator. JIB - Box top section telescopes from lattice type base section which stores alongside base boom section. 5 o or 3 offset (tilt type). Single sheave,17-1/4"(0.438m) root diameter, at jib head. Jib length is 32.2 (9.8m) or 56.1' (17.1m). AUXILIARY LIFTING SHEAVE (SINGLE TOP) - Single sheave, 17-1/4"(0.438m) root diameter. Mounted to main boom head for single line work (stowable). ANTI-TWO BLOCK - Pendant type over-winding cut out device with audio-visual (FAILURE lamp/buzzer) warning system. SWING Hydraulic axial piston motor driven through planetary swing speed reducer. Continuous 36 full circle swing on ball bearing turntable at 2.4 rpm. Equipped with manually locked/released swing brake. A swing lock (36 positive swing lock) for pick and carry and travel modes, manually engaged in cab. HOIST MAIN HOIST - Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and raising. Equipped with automatic brake (neutral brake) and counterbalance valve. Controlled independently of auxiliary hoist. Equipped with cable follower and drum rotation indicator. DRUM - Grooved 15-3/4"(0.400m) root diameter x 22-3/4" (0.578m) wide. Wire rope: 623' of 3/4" diameter rope (190m of 19mm). Drum capacity: 905'(276m) 6 layers. Maximum line pull (permissible): 14,272lbs. (6,474kg)*. Maximum line speed: 525 FPM (160m/min). AUXILIARY HOIST - Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and raising. Equipped with automatic brake (neutral brake) and counterbalance valve. Controlled independently from main hoist. Equipped with cable follower and drum rotation indicator. WIRE ROPE - Filler wire, extra improved plow steel, preformed, independent wire rope core, right regular lay. 3/4"(19 mm) 6x37 class HOOK BLOCKS ton (45.4 metric ton) - 4 sheaves with swivel hook and safety latch, for 3/4"(19mm) wire rope ton (5.6 metric ton) - Weighted hook with swivel and safety latch, for 3/4"(19mm) wire rope. HYDRAULIC SYSTEM PUMPS - Two variable piston pumps for crane functions. Tandem gear pump for steering, swing and optional equipment. Powered by carrier engine. Pump disconnect for crane is engaged/ disengaged by rotary switch from operator's cab. CONTROL VALVES - Multiple valves actuated by hand levers with integral pressure relief valves. RESERVOIR gallon (740 lit.) capacity. External sight level gauge. FILTRATION - 26 micron return filter, full flow with bypass protection, located inside of hydraulic reservoir. Accessible for easy replacement. OIL COOLER - Air cooled fan type. CAB AND CONTROLS Both crane and drive operations can be performed from one cab mounted on rotating superstructure. Left side, 1 man type, steel construction with sliding door access and safety glass windows opening at side, rear and roof. Windshield glass window is shatter-resistant. Tilttelescoping steering wheel. Adjustable control levers for swing, boom hoist, boom telescoping, auxiliary hoist and main hoist. Control levers for swing and auxiliary hoist can change neutral positions and tilt for easy access to cab. Engine throttle knob. Foot operated controls: boom hoist, boom telescoping, service brake and engine throttle. Dash-mounted engine start/stop, monitor lamps, cigarette lighter, parking brake switch, steering mode select switch, pump engaged/disengaged switch, swing brake switch, and telescoping correction switches. Instruments - Torque converter oil temperature, engine water temperature, air pressure, fuel, speedometer, tachometer and hour meter. Torque converter oil pressure and hydraulic oil pressure are monitored and displayed on the AML-L display panel. DRUM - Grooved 15-3/4"(0.400m) root diameter x 22-3/4" (0.578m) wide. Wire rope: 361' of 3/4" diameter rope (110 m of 19mm). Drum capacity: 905'(276m) 6 layers. Maximum line pull (permissible): 14,272 lbs. (6,474kg)*. Maximum line speed: 525 FPM (160m/min). * Maximum permissible line pull may be affected by wire rope strength. 2

3 Tadano electronic LOAD MOMENT INDICATOR system (AML-L) including: h Control lever lockout function h Load radius and/or boom angle preset function (warning only) h Warning buzzer h Boom angle/boom length/jib offset angle/load radius/rated lifting capacities/actual loads read out h Ratio of actual load moment to rated load moment indication h Working condition register switch h External warning lamp h TADANO AML-L monitors outrigger extended length and automatically programs the corresponding "Rated Lifting Capacities" for crane duty in confined areas. Operator's right hand console includes transmission gear selector, outrigger controls, sight level bubble, drive selector switch, swing free-lock selector switch, working light switch and ashtray. Swing lock lever and 3 way adjustable seat with high back and seat belt. NOTE: Each crane motion speed is based on unladen conditions. CARRIER SPECIFICATIONS TYPE - Rear engine, left hand steering, driving axle 2-way selected type by manual switch, 4x2 front drive, 4x4 front and rear drive. FRAME - High tensile steel, all welded mono-box construction. SUSPENSION - Front: Rigid mounted to frame. Rear: Pivot mounted with hydraulic lockout cylinders. BRAKE SYSTEMS - Service: Air over hydraulic disc brakes on all 4 wheels. Parking/Emergency: Spring applied-air released brake acting on input shaft of front axle. TRANSMISSION - Electronically controlled full automatic TIRES PR(OR) transmission. Torque converter driving full powershift with driving axle selector. 6 forward and 2 reverse speeds, constant OUTRIGGERS - Four hydraulic, beam and jack outriggers. mesh. Vertical jack cylinders equipped with integral holding valve. 3 speeds - high range - 2 wheel drive; 4 wheel drive Each outrigger beam and jack is controlled independently from 3 speeds - low range - 4 wheel drive cab. Beams extend to 23' 7-1/2" (7.2 m) center-line and retract to within 10' 10-1/2" (3.315 m) overall width with floats. TRAVEL SPEED - 25 mph (40 km/h) Outrigger jack floats are attached thus eliminating the need of manually attaching and detaching them. Controls and sight AXLE - Front: Full floating type, steering and driving axle with bubble located in upper structure cab. planetary reduction. Rear: Pivot-mounted, steering and driving axle Three outrigger extension lengths are provided with with planetary reduction and non-spin rear differential. corresponding "Rated Lifting Capacities" for crane duty in confined areas. STEERING- Hydraulic power steering controlled by steering Mid. Extension 18'1/2" center to center floats wheel. Three steering modes available: 2 wheel front, 4 wheel Mid. Extension 21'11-3/4" center to center floats coordinated and 4 wheel crab. Max. extension 23'7-1/2" center to center floats ENGINE Model Mitsubishi 6D16-TLEA Radiator Fin and tube core, thermostat controlled Type Direct injection diesel Fan, in.(mm) Suction type, 6-blade, 23.6 (600) dia. No. of cylinders 6 Starting 24 volt Combustion 4 cycle, turbo charged and after cooled Charging 24 volt system, negative ground BoreXStroke, in.(mm) X (118X115) Battery amp. Hour Displacement, cu. in (liters) 460 (7.545) Compressor, air, CFM(l /min) 10.6 CFM (301) at 2,000rpm Air inlet heater 24 volt preheat Horsepower (kw) Gross 247 (184) at 2,800rpm Air cleaner Dry type, replaceable element Torque, Max. ft-lb (kgm) 521 (72) at 1,400rpm Oil filter Full flow with replaceable element Capacity, gal.(liters) Fuel filter Full flow with replaceable element Cooling water 3.4 (13) Fuel tank, gal.(liters) 79.2 (300), right side of carrier Lubrication 3.7 ~ 4.2 (14 ~ 16) Cooling Liquid pressurized, recirculating by-pass Fuel 79.2 (300) 3

4 STANDARD EQUIPMENT - Four section full power partially synchronized boom - Ratio of actual load moment to rated load moment indication 34.8'~110.6' (10.6 m~33.7 m) - Working condition register switch - Two stage stowable telescoping jib 32.2' (9.8 m) or 56.1' (17.1m) - External warning lamp with 5 o or 3 pinned offset (tilt type) with self storing pins - Tinted safety glass - Auxiliary lifting sheave (single top) stowable - Front windshield wiper and washer - Boom hoist foot control - Roof window wiper and washer - Boom telescoping foot control - Roof window lock warning - Boom angle indicator - Rear view mirrors (right and left side) - Variable speed main hoist with grooved drum, cable follower - Mirror for main and auxiliary hoists and 623' of 3/4 cable - 3 way adjustable seat with high back and seat belt - Variable speed Auxiliary hoist with grooved drum, cable - Tilt-telescoping steering wheel follower and 361' of 3/4 cable - Neutral position adjustable control lever (swing and aux. hoist) - Drum rotation indicator (thumper type) main and auxiliary hoist - Cab floor mat - Tadano twin swing system - Cigarette lighter - 36 positive swing lock - Electric fan in cab - 4 X 4 X 4 drive/steer - Back-up alarm - Disc Brakes - Low oil pressure/high water temp. warning device (visual) - Automatic rear axle oscillation lockout system - Rear steer centering light - Non-spin rear differential - Fenders PR (OR) tires - Air cleaner dust indicator - Independently controlled outriggers - Towing hooks-front and rear - Self-storing outrigger pads - Lifting eyes - Three outrigger extension positions - Tool storage compartment - Outrigger extension length detector - Full instrumentation package - Outrigger hose protection - Pump disconnect in operator's cab - Mitsubishi 6D16-TLEA Turbo Charged after cooled engine - Air dryer (247 HP) with exhaust brake - Water separator with filter - Electronic controlled Automatic transmission driven by torque - Flood lights and work lights converter - Tire inflation kit - Engine over-run alarm - Hydraulic oil cooler - Complete highway light package - 24 volt electric system - Anti-Two block device (overwind cutout) - 50 ton (45.4 metric ton) 4 sheave hook block - Electronic crane monitoring system ton (5.6 metric ton) hook with swivel - Tadano electronic load moment indicator system (AML-L) - Hook block tie down (front bumper) including - Control lever lockout function - Working radius and/or boom angle and/or tip height preset function (warning only) OPTIONAL EQUIPMENT - Hydraulic oil driven cab heater and air conditioner - Warning buzzer - Propane heater (less tank) - Boom angle / boom length / jib offset angle / working radius / rated loads / actual loads read out HOISTING SPECIFICATIONS LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES Layer Speed Main or auxiliary hoist - 15'-3/4" (0.4m) drum Main and auxiliary drum grooved lagging Wire Line speeds 2 Line pulls 3/4" (19mm) wire rope Available 1 Permissible 4 rope Rope per layer Total wire rope layer F.P.M m/min Lbs. kgf Lbs. kgf Feet Meters Feet Meters 1st 2nd 3rd 4th 5th 6th 3 Low ,698 7,121 14,272 6,474 High Low ,647 6,644 13,315 6,040 High Low ,520 6,133 12,292 5,576 High Low ,557 5,696 11,416 5,179 High DRUM DIMENSIONS Low Inch mm 11,721 5,317 10,657 4,834 High Root diameter 15-3/4" 400 Low Length 22-3/4" ,989 4,985 9,991 4,532 High Flange diameter 25-3/8" Developed by machinery with first layer of wire rope, but not based on rope strength or other limitation in machinery or equipment. 2 Line speeds based only on hook block, not loaded. 3 Sixth layer of wire rope is not recommended for hoisting operations. 4 Permissible line pull may be affected by wire rope strength. 4

5 TR-500XL-3 WORKING RANGE CHART Lifting Height in Feet Axis of Rotation Load radius from Axis of Rotation in Feet NOTE: Boom and jib geometry shown are for unloaded condition and machine standing level on firm supporting surface. Boom deflection and subsequent radius and boom angle change must be accounted for when applying load to hook. 5

6 TR-500XL-3 RATED LIFTING CAPACITIES (IN POUNDS) A 34.8' 47' 60' 72' 85' 98' 110.6' B (10.6m) (14.3m) (18.3m) (21.9m) (25.9m) (29.9m) (33.7m) 10' 100,000 88,200 68,000 ON OUTRIGGERS FULLY EXTENDED 36 ROTATION (33.7m) Boom (9.8m) Jib 5 o offset 3 offset 3 offset 12' 92,600 87,200 63,500 40,700 Degree R W R W R W R W 15' 77,500 77,000 57,800 40,700 38, , , , ,300 20' 59,700 59,200 47,400 40,700 38,000 32, o , , , ,200 25' 47,700 47,200 40,000 35,300 31,200 27,800 24, , , , ,900 30' 38,600 33,900 29,800 26,200 23,300 21, o , , , ,800 35' 30,300 28,700 25,500 22,500 20,000 18, , , , ,700 40' 23,700 22,500 22,400 19,600 17,300 15, o , , , ,600 45' 17,700 19,500 17,200 15,200 13, , , , ,400 50' 14,400 15,700 15,200 13,500 12, o , , , ,300 55' 12,900 13,500 12,000 11, , , , ,200 60' 10,600 11,400 10,800 9, o , ,600 65' 9,000 9,400 9,500 8,700 70' 8,100 8,100 7,900 75' 7,000 6,900 7,100 A: Boom length in feet 80' 6,200 6,400 B: Load radius in feet 85' 5,400 5,600 C: Minimum boom angle (deg.) for indicated length (no load) 90' 4,800 4,800 R: Load radius in feet 95' 3,900 W: Rated lifting capacity in pounds 100' 3, ' 2,500 C Boom Angle in (33.7m) Boom (17.1m) Jib 5 o offset A 34.8' 47' 60' 72' 85' 98' 110.6' B (10.6m) (14.3m) (18.3m) (21.9m) (25.9m) (29.9m) (33.7m) 10' 100,000 88,200 68,000 ON OUTRIGGERS MID. EXTENDED 21'11-3/4" (6.7m) SPREAD 36 ROTATION 5 o offset 3 offset 12' 92,600 87,200 63,500 40,700 Degree R W R W R W R W 15' 77,500 77,000 57,800 40,700 38, , , , ,300 20' 59,700 59,200 47,400 40,700 38,000 32, o , , , ,200 25' 47,700 47,200 40,000 35,300 31,200 27,800 24, , , , ,900 30' 34,100 33,600 29,800 26,200 23,300 21, o , , , ,800 35' 25,100 24,700 25,500 22,500 20,000 18, , , , ,700 40' 19,300 18,700 20,000 19,600 17,300 15, o , , , ,600 45' 14,500 15,600 16,900 15,200 13, , , , ,400 50' 11,500 12,800 13,600 13,500 12, o , , , ,100 55' 10,400 11,200 11,400 11, , ,100 60' 8,400 9,100 9,500 9, o 65' 6,900 7,500 7,900 8,200 70' 6,100 6,600 6,800 75' 5,100 5,500 5,900 A: Boom length in feet 80' 4,700 5,000 B: Load radius in feet 85' 3,800 4,100 C: Minimum boom angle (deg.) for indicated length (no load) 90' 3,100 3,400 R: Load radius in feet 95' 2,700 W: Rated lifting capacity in pounds 100' 2, ' 1,800 C Boom Angle in (33.7m) Boom (9.8m) Jib 5 o offset 3 offset (33.7m) Boom (17.1m) Jib 6

7 TR-500XL-3 RATED LIFTING CAPACITIES (IN POUNDS) ON OUTRIGGERS MID. EXTENDED 18' 1/2" (5.5m) SPREAD 36 ROTATION A 34.8' 47' 60' 72' 85' 98' 110.6' Boom 110.6' (33.7m) Boom ' (33.7m) Boom B (10.6m) (14.3m) (18.3m) (21.9m) (25.9m) (29.9m) (33.7m) Angle (9.8m) Jib (17.1m) Jib 10' 100,000 88,200 68,000 in 5 o offset 3 offset 5 o offset 3 offset 12' 92,600 87,200 63,500 40,700 Degree R W R W R W R W 15' 77,500 77,000 57,800 40,700 38, , , , ,300 20' 54,700 54,000 47,400 40,700 38,000 32, o , , , ,200 25' 36,000 34,500 33,700 35,300 31,200 27,800 24, , , , ,900 30' 24,300 23,800 25,000 26,200 23,300 21, o , , , ,800 35' 17,800 17,400 18,600 20,000 20,000 18, , , , ,700 40' 13,600 13,100 14,100 15,400 16,200 15, o , , , ,200 45' 9,900 11,100 12,100 12,800 13, , ,100 50' 55' 60' 65' 70' 7,600 8,500 6,700 5,100 4,000 9,600 7,700 6,100 4,800 3,700 10,100 8,100 6,400 5,200 4,100 10,700 8,800 7,200 5,900 4, o 4 35 o 75' 3,000 3,200 3,700 A: Boom length in feet 80' 2,600 3,000 B: Load radius in feet 85' 2,000 2,300 C: Minimum boom angle (deg.) for indicated length (no load) 90' 1,700 R: Load radius in feet 95' 100' 104' C 27 o Boom length in feet 34.8' (10.5m) 47' (14.2m) 60' (18.2m) 72' (21.8m) 85' (25.8m) 98' (29.8m) 110.6' (33.6m) NOTE: Load radiuses for jib operation are given for reference with the boom fully extended to 110.6' (33.7m). 6,200 lbs. (2,800 kg) shall be subtracted from the rated lifting capacity of main boom, when jib is attached to main boom head. Jib weight is 2,200 lbs. (1,000 kg). Standard number of parts of line for outrigger operation should be according to the following table. Boom Length in Feet (meters) 34.8' (10.6) 34.8' to 47' (10.6 to 14.3) 473' to 60' (14.3 to 18.3) 60' to 110.6' (183 to 33.7) Single top Jib No. of parts of line The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line listed in the chart. 7

8 WARNING AND OPERATING INSTRUCTIONS FOR LIFTING CAPACITIES GENERAL 10. When making lifts at a load radius not shown, use the next 1. RATED LIFTING CAPACITIES apply only to the machine as longer radius to determine allowable capacity. originally manufactured and normally equipped by TADANO 11. Load per line should not exceed 11,400 lbs. (5,200kg) for LTD. Modifications to the machine or use of optional main winch and 12,300 lbs. (5,600kg) for auxiliary winch. equipment other than that specified can result in a reduction 12. Check the actual number of parts of line with LOAD of capacity. MOMENT INDICATOR (AML-L) before operation. Maximum 2. Construction equipment can be hazardous if improperly lifting capacity is restricted by the number of parts of line of operated or maintained. Operation and maintenance of this LOAD MOMENT INDICATOR (AML-L). Limited capacity is machine must be in compliance with information in the as determined from the formula, Single line pull for main operation and maintenance manual supplied with the machine. winch (11,400 lbs.) x number of parts of line. If this manual is missing, order a replacement through 13. The boom angle before loading should be greater to account the distributor. for deflection. 3. The operator and other personnel associated with this 14. The 34.8' (10.6m) boom length capacities are based on machine shall fully acquaint themselves with the latest boom fully retracted. If not fully retracted [less than 47' American National Standards Institute (ANSI) safety (14.3m) boom length], use the rated lifting capacities for the standards for cranes. 47' (14.3m) boom length. 15. Extension or retraction of the boom with loads may be SET UP attempted within the limits of the RATED LIFTING 1. Rated lifting capacities on the load chart are the maximum CAPACITIES. The ability to telescope loads is limited by allowable crane capacities. They are based on the machine hydraulic pressure, boom angle, boom length, crane standing level on a firm supporting surface under ideal job maintenance, etc. conditions. Depending on the nature of the supporting 16. For lifting capacity of single top, reduce the rated lifting surface, it may be necessary to have structural supports capacities of relevant boom by the mass of the main hook under the outrigger floats or tires to spread the loads to a block. Capacities of single top shall not exceed 12,300 lbs. larger surface. (5,600 kg) including main hook. 2. For outrigger operation, outriggers shall be properly extended 17. When erecting and stowing jib, be sure to retain it by hand or with tires free of supporting surface before operating crane. by other means to prevent its free movement ,200 lbs. (2,800 kg) shall be subtracted from the rated lifting OPERATION capacities of the main boom, when jib is attached to main 1. Rated lifting capacities have been tested to and meet boom head. Jib mass is 2,200 lbs. (1,000 kg). minimum requirements of SAE J1063-Cantilevered Boom 19. Use Anti-two block (OVERWIND CUTOUT) disable switch Crane Structures Method of Test. when erecting and stowing jib and when stowing hook block. 2. Rated lifting capacities do not exceed 85 % of the tipping While the switch is pushed, the hoist does not stop, even load on outriggers fully extended as determined by SAE when overwind condition occurs. J765-Crane Stability Test Code. 20. For boom length with 32.2' (9.8 m) jib, rated lifting capacities Rated lifting capacities for partially extended outriggers are are determined by loaded boom angle only in the column determined by this formula, Rated Lifting Capacities headed 110.6' (33.7m) boom ' (9.8m) jib. For boom =(Tipping Load Ð 0.1 x Tip Reaction)/1.25. length with 56.1' (17.1m) jib, rated lifting capacities are 3. Rated lifting capacities above bold lines in the chart are determined by loaded boom angle only in the column headed based on crane strength and those below, on its stability ' (33.7m) boom ' (17.1m) jib. For angles not They are based on actual load radius increased by boom shown, use the next lower loaded boom angle to determine deflection. allowable capacity 4. The weight of load handling device such as main hook block 21. When lifting a load by using jib (aux. winch) and boom (main (950 lbs. for 50 ton capacity), auxiliary hook block (330 lbs. winch) simultaneously, do the following: for 6.2 ton capacity), slings, etc., must be considered as part h Enter the operation status as jib operation, not as boom of the load and must be deducted from the lifting capacities. operation. 5. Rated lifting capacities are based on freely suspended loads h Before starting operation, make sure that mass of load is and make no allowance for such factors as the effect of wind, within rated lifting capacity for jib. sudden stopping of loads, supporting surface conditions, inflation of tires, operating speeds, side loads, etc. Side pull on the boom or jib is extremely dangerous. 6. Rated lifting capacities do not account for the effect of wind DEFINITIONS on a lifted load or boom. Rated lifting capacities and boom 1. Load Radius: Horizontal distance from a projection of the length shall be appropriately reduced, when wind velocity axis of rotation to supporting surface before loading to the exceeds 20 mph (9 m/sec.). center of the vertical hoist line or tackle with load applied. 7. Rated lifting capacities at load radius shall not be exceeded. 2. Loaded Boom Angle: The angle between the boom base Do not tip the crane to determine allowable loads. section and the horizontal, after lifting the rated lifting 8. Do not operate at boom lengths, radii, or boom angle, where capacity at the load radius. no capacities are shown. Crane may overturn without any 3. Working Area: Area measured in a circular arc about the load on the hook. centerline of rotation. 9. When boom length is between values listed, refer to the 4. Freely Suspended Load: Load hanging free with no direct rated lifting capacities of the next longer and next shorter external force applied except by the hoist line. booms for the same radius. The lesser of the two rated lifting 5. Side Load: Horizontal side force applied to the lifted load capacities shall be used. either on the ground or in the air. 8

9 TR-500XL-3 RATED LIFTING CAPACITIES (IN POUNDS) Load Radius in Feet 10' 12' 15' 20' 25' 30' 35' 40' 45' 50' TIRE : PR ON RUBBER Stationary Creep 34.7' Over Front Boom Length in Feet 60.0' 85' 34.7' 36 Rotation Boom Length in Feet 60.0' 85' 34.7' Over Front Boom Length in Feet 60.0' 85' (10.7m) 55,700 49,600 (18.3m) 34,000 (25.9m) (10.7m) 34,200 33,200 (18.3m) 27,000 (25.9m) (10.6m) 48,300 41,700 (18.3m) 30,500 (25.9m) 44,000 34,000 16,500 24,000 23,300 34,100 30,500 14,800 33,200 28,000 16,500 14,800 13,700 15,500 25,700 25,100 14,800 22,900 22,400 16,500 9,400 8,800 10,300 20,100 19,300 14,800 15,800 16,500 5,500 7,000 15,100 14,800 11,600 13,500 3,100 4,600 11,600 13,300 8,700 10,400 3,000 8,700 10,400 6,600 8,100 6,600 8,100 4,800 6,500 4,800 6,500 5,000 5,000 3,900 3,900 3,100 3,100 55' 60' 65' 70' 2,300 75' 1,700 A 43 o 56 o A : Minimum boom angle (deg.) for indicated length (no load) 2,300 1,700 Boom length in feet 36.1' (11.0m) 62.3' (19.0m) 85' (25.9m) Working area Over front Approx. 2 o 36 Rear NOTE: Standard number of parts of line for outrigger operation should be according to the following table. Boom Length in Feet 34.8' (meters) (10.6) No. of parts of line ' to 85' (10.6 to 25.9) 4 Single top 1 The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-L) is based on the standard number of parts of line listed in the chart. WARNING AND OPERATING INSTRUCTIONS FOR ON RUBBER LIFTING CAPACITIES 1. Rated lifting capacities on rubber are in pounds and do not exceed 6. Over front operation shall be performed within two degrees in front of 75 % of tipping loads as determined by SAE J765-Crane Stability chassis. Test Code. 7. On rubber lifting with "jib" is not permitted. Maximum permissible 2. Rated lifting capacities shown in the chart are based on condition that boom length is 85 ft. (25.9 m). crane is set on firm level surfaces with axle oscillation lockout 8. When making lift on rubber (stationary), set parking brake. applied. Those above bold lines are based on tire capacity and those 9. For creep operation, boom must be centered over front of machine, below, on crane stability. They are based on actual load radius swing lock engaged, and load restrained from swinging. Travel slowly increased by tire deformation and boom deflection. and keep the lifted load as close to the ground as possible, and 3. If the axle oscillation lockout cylinders contain air, the axle will not be especially avoid any abrupt steering, accelerating or braking. locked completely and rated lifting capacities may not be obtainable. 10. Do not operate the crane while carrying the load. Bleed the cylinders according to the operation, safety and 11. Creep is motion for crane not to travel more than 200 ft. (60 m) in any maintenance manual. 30 minute period and to travel at the speed of less than 1 mph ( Rated lifting capacities are based on proper tire inflation, capacity km/h). and condition. Damaged tires are hazardous to safe operation of 12. For creep operation, set drive select switch to "4-WHEEL (Lo)" and crane. set gear shift lever to "1". 5. Tires shall be inflated to correct air pressure. Tires Air Pressure PR 60 psi. (4.2kgf/cm 2 ) 9

10 WARNING AND OPERATING INSTRUCTIONS FOR USING THE LOAD MOMENT INDICATOR (AML-L) 1. When operating crane on outriggers: h When a load is lifted in the front position and then h Set P.T.O. switch to "ON". swung to the side area, make sure the value of the h Press the outrigger mode select key to register for the LOAD MOMENT INDICATOR (AML-L) is below the outrigger operation. Press the set key, then the 36 lifting capacity. outrigger mode indicative symbol changes from (2) For creep operation : flickering to lighting. h The creep capacities are attainable only when boom h Press the boom mode select key to register the boom is in the straight forward position of chassis and the mode, then the boom mode indicative symbol changes over front position symbol is on. If boom is not in the from lighting to flickering. Each time the boom mode straight forward position of chassis, never lift load. select key is pressed, the mode changes. Press the set 3. A swing dose not automatically stop even if the crane key to select the status that corresponds to the actual becomes overloaded. state of the boom, then the boom mode indicative 4. During crane operation, make sure that the displays on symbol changes from flickering to lighting. front panel are in accordance with actual operating h When erecting and stowing jib, select the status of jib conditions. set (jib state indicative symbol flicker). 5. The displayed values of LOAD MOMENT INDICATOR 2. When operating crane on rubber: (AML-L) are based on freely suspended loads and h Set P.T.O. switch to "ON". make no allowance for such factors as the effect of h Press the on-tire mode select key. The on-tire mode wind, sudden stopping of loads, supporting surface indicative symbol comes on. Each time the on-tire conditions, inflation of tire, operating speed, side loads, mode select key is pressed, the mode changes. etc. For safe operation, it is recommended when Select the creep operation, the on-tire mode extending and lowering boom or swinging, lifting loads indicative symbol flicker. shall be appropriately reduced. h Press the boom mode select key to register the boom 6. LOAD MOMENT INDICATOR (AML-L) is intended as mode. an aid to the operator. Under no condition should it be However, pay attention to the following : relied upon to replace use of capacity charts and (1) For stationary operation : operating instructions. Sole reliance upon LOAD h The front capacities are attainable only when the over MOMENT INDICATOR (AML-L) aids in place of good front position symbol comes on. When the boom is operating practice can cause an accident. The operator more than 2 degrees from centered over front of must exercise caution to assure safety. chassis, 36 capacities are in effect. TR-500XL-3 Axle weight distribution chart Basic standard machine includes: 34.8'~ 110.6' (10.6 m ~ 33.7 m) 4-section boom 32.2', 56.1'(9.8 m, 17.1 m) 2-stage jib Main hoist with 623' (190 m) of 3/4" (19 mm) diameter wire rope Auxiliary hoist with 361' (110 m) of 3/4" (19 mm) diameter wire rope 50 ton (45.4 metric ton) hook block 6.2 ton (5.6 metric ton) hook ball Auxiliary lifting sheave (single top) Mitsubishi 6D16-TLEA engine PR(OR) tires GVW 88,200 Pounds Front 45,690 Rear 42,510 Kilograms GVW Front Rear 40,000 20,720 19,280 Remove: ', 56.1' (9.8 m, 17.1 m) 2-stage jib -2,200-3,740 +1,540 -,1000-1, ton (45.4 metric ton) hook block , ton (5.6 metric ton) hook ball Auxiliary lifting sheave (single top) PR (OR) tires -6,990-3,495-3,495-3,172-1,586-1,586 10