Command Emulator STAR Line Mode Command Specifications
|
|
|
- Everett Sims
- 7 years ago
- Views:
Transcription
1 Line Thermal Printer Command Emulator STAR Line Mode Command Specifications Revision 0.01 Star Micronics Co., Ltd. Special Products Division
2 Table of Contents 1. Command Emulator 2 1-1) Command List 2 1-2) Command Details 3 1-3) List of Compatible Models 5 2. STAR Line Mode 6 2-1) Command List 6 2-2) List of Compatible Models 13
3 This is the Command Emulator Command Specifications Manual created based on Command Emulator dedicated commands and the Star Line Mode Command Specifications Manual. Information contained herein applies to the following models. < Applicable Models> TSP100 TSP700II
4 1. Command Emulator The commands outlined below are dedicated to the Command Emulator. 1-1) Command List ESC US A ESC US f ESC US p Name Set print region with in mm units Switch to country of destination Specify delimiter 2
5 1-2) Command Details ESC US A [Name] Set print region with in mm units [Code] ASCII ESC : US A n Hexadecimal 1B F 41 n Decimal n [Defined Area] 0 n 255 [Initial Value] Depends on Config setting [Function] Sets the printer region width to n mm. This sets the print region width when processing this command, and unprinted data remaining in the expanded buffer is printed. The print region width is set by left side alignment. The left and right margin settings are initialized. The print region width is set by left alignment so the horizontal tab positions are not initialized. initialize this command setting. (Returns to the Config setting) ESC US f [Name] Switch to country of destination [Code] ASCII ESC : US f n Hexadecimal 1B F 66 n ecimal n [Defined Area] 0 n 4 48 n 52 ( 0 n 4 ) [Initial Value] Depends on Config setting [Function] Specifies country of destination. and CAN initialize this command setting. (Returns to the Config set ting) n Country of Destination 0 0 SBCS 1 1 Japan 2 2 China 3 3 Taiwan 4 4 Korea 3
6 Only in STAR Line Mode; See the specifications below. The default ANK pitch is switched by the memory switch writing command <ESC> <GS> #. Default International Characters Code Page ANK Pitch Default <ESC> R n Default <ESC><GS> t n SBCS 12/15 dots USA Command Enabled Normal Command Enabled Japan 12/15 dots Japan Command Disabled Normal Command Disabled (Ignores 3 Bytes) (Katakana) (Ignores 4 Bytes) China 13/15 dots USA Command Enabled Normal Command Disabled (Katakana) (Ignores 4 Bytes) Taiwan (Katakana) (Ignores 4 Bytes) Normal Command Disabled 13/15 dots USA Command Enabled Korea 13/15 dots Korea Command Disabled Normal Command Disabled (Ignores 3 Bytes) (Katakana) (Ignores 4 Bytes) ESC US p [Name] Specify delimiter [Code] ASCII ESC : US p n Hexadecimal 1B F 70 n Decimal n [Defined Area] 0 n 3 48 n 51 ( 0 n 3 ) [Initial Value] [Function] Specifies delimiter. n Content 0 0 Top of document 1 1 Top of page 2 2 Bottom of page 3 3 Bottom of document This command determines the printing job data boundary for the command emulator plug-in. The plug-in finds these delimiters and executes a process. If the command emulator plug-in is not registered, these delimiters are ignored. 4
7 1-3) List of Compatible Models Class Model Name TSP100 TS- P700II Command Emulator Special ESC US A ESC US f ESC US p 5
8 2. STAR Line Mode 2-1) Command List Refer to the Star Line Mode Command Specifications for details of the commands. Font Style and Character Set Character Expansion Settings Print Modes ESC E ESC F ESC - ESC _ ESC 4 ESC 5 SI DC2 Line Spacing ESC RS F Select font 4 bytes ignored ESC GS t Specify code page IBM block uses vertical 24 dot fonts (for ESC/POS) ESC GS = Write blank code page data *1 ESC R Specify international character set ESC / Specify/cancel slash zero ESC SP Set ANK right space ESC M Specify ANK 12 dot pitch ESC P Specify ANK 15 dot pitch ESC : Specify ANK 16 dot pitch ESC g Specify ANK 14 dot pitch ESC i Set/cancel the double wide/high printing ESC W Set/cancel the double wide printing ESC h Set/cancel the double high printing SO Set double wide printing DC4 Cancel double wide printing ESC SO Set printing vertical double high characters ESC DC4 Cancel printing magnified character height LF CR ESC a ESC z ESC 0 ESC J ESC I Select emphasized printing Cancel emphasized printing Select/cancels underline mode Select/cancels upperline mode Selects white/black inverted printing Cancel white/black inverted printing Selects upside-down printing Cancel upside-down printing Line feed Carriage return (same as line feed) Feed paper n lines Select line feed amount Specify line feed to 3 mm n/4 mm line feed n/8mm line feed 6
9 Page Control FF ESC C ESC C 0 VT ESC B Form feed Set page length to n lines Set page length in 24 mm units Feed paper to vertical table position Set vertical tab position 7
10 Horizontal Direction Position ESC I ESC Q HT ESC D ESC GS A ESC GS R ESC GS a Set left margin Set right margin Move print position to horizontal tab position Set/cancel horizontal tab position Move absolute position Move relative position Specify position alignment Enabled only at top of line (Specification 2 of the Star Line Mode Command Specifications) Enabled only at top of line (Specification 2 of the Star Line Mode Command Specifications) Reference point is lefts edge of paper (same as TSP1000) Download ESC & ESC % Register/delete download characters Set/cancel download characters Bit Image Graphics ESC K Standard density bit image ESC L High density bit image ESC k Fine bit image ESC X Fine bit image (wire dot conversion) Prints only printable protion when counter exceeds print region. Logos ESC FS q Register logo data *1 ESC FS p Print logo data Registration size up to x (normally 1023 x 288) Bar Codes ESC b Cutter Control ESC d Print bar code Paper cut instruction External Device Drive ESC BEL Set pulse width for external device drive BEL External device 1 drive instruction FS External device 1 drive instruction SUB External device 2 drive instruction EM External device 2 drive instruction ESC GS BEL Ring buzzer Print Setting ESC RS d ESC RS r Set print density Set print speed 8
11 Status ESC RS a Set status transmission conditions 4 bytes ignored ESC ACK SOH Real-time printer status (ASB Status) When using a serial port emulator, operations are possible. ENQ Real-time printer status (1) EOT Real-time printer status (2) ETB Update of ETB status 1 byte ignored ESC RS E Clear ETB counter, ETB status 4 bytes ignored Chinese Characters ESC p Set to JIS Chinese character mode ESC q Cancel JIS Chinese character mode ESC $ Set/cancel JIS Chinese character mode ESC s Set two byte Chinese characters left/right spaces ESC t Set 1 byte Chinese characters left/right spaces ESC r Register Chinese download characters Others CAN Cancel print data and initialize commands Does not clear reception buffer Not real-time command. Command initialization ESC GS # Set memory switch *2 ESC? Reset printer Only reset command (command for manufacturing unsupported) Raster ESC * r R Initialize raster mode 2 bytes ignored ESC * r A Enter raster mode 2 bytes ignored ESC * r B Quit raster mode 2 bytes ignored ESC * r C Clear raster data 2 bytes ignored ESC * r D Drawer drive 2 bytes ignored ESC * r E Set EOT mode 2 bytes ignored ESC * r F Set FF mode 2 bytes ignored ESC * r P Set page length 2 bytes ignored ESC * r Q Set print quality 2 bytes ignored ESC * r m l Set left margin 2 bytes ignored ESC * r m r Set right margin 2 bytes ignored ESC * r T Set top margin 2 bytes ignored ESC * r K Set print color 2 bytes ignored b n1 n2 d1 dk Transfer raster data (auto line feed) Processes from top of data as ASCII data k n1 n2 d1 dk Transfer raster data Processes from top of data as ASCII data ESC * r Y Move vertical direction position (Line feed for specified dots) 2 bytes ignored ESC FF NUL Execute form feed mode 2 bytes ignored ESC FF EOT Execute EOT mode 2 bytes ignored
12 Black Mark 2-Color Printing ESC d Paper cut instruction Same as operations in normal mode FF Form feed ESC C Set page length to n lines ESC C 0 Set page length in 24 mm units VT Feed paper to vertical table position ESC B Set vertical tab position ESC RS c Specify printing color in 2 color printing mode ESC RS C Select/cancel 2 color printing mode ESC 4 Specify white/black inversion and printing color red ESC 5 Specify white/black inversion and printing color black ESC RS d Set print density ESC RS r Set printing speed ESC FS q Register logo *1 ESC FS p Print logo 10
13 Presenter Mark Auto Logo ESC SYN 0 Execute presenter paper recovery 2 bytes ignored ESC SYN 1 Set presenter automatic recovery function and recovery time ESC SYN 3 Acquire presenter paper counter ESC SYN 4 Initialize presenter paper counter ESC GS * 0 Print mark 3 bytes ignored ESC GS * 1 Specify mark height and line feed amount ESC GS * 2 Specify mark color and horizontal width in each mark number ESC GS * W Register mark format to non-volatile memory ESC GS * C Initialize mark format from non-volatile memory ESC GS / W Register Auto Logo setting to non-volatile memory ESC GS / C Initialize Auto Logo setting from non-volatile memory ESC GS / 1 Set ON/OFF for Auto Logo function ESC GS / 2 Set command characters ESC GS / 3 Set user macro 1 ESC GS / 4 Set user macro 2 ESC GS / 5 Set command character switching method ESC GS / 6 Set partial cut just prior to Auto Logo printing 3 bytes ignored PDF417 ESC GS x S 0 Set bar code size 3 bytes ignored ESC GS x S 1 Set security level (ECC) ESC GS x S 2 Set module x direction size ESC GS x S 3 Set module aspect ratio ESC GS x D Set bar code data ESC GS x P Print bar code ESC GS x I Get bar code expansion information Print Start Trigger Control ESC GS g 0 Print starting trigger 3 bytes ignored ESC GS g 1 Set print start timer 3 bytes ignored 11
14 QR Code ESC GS y S 0 Set model ESC GS y S 1 Set error correction level ESC GS y S 2 Set cell size ESC GS y D 1 Set data (auto) ESC GS y D 2 Set data (manual) ESC GS y P Print QR code ESC GS y I Get expansion information (bar code size) 4 bytes ignored *1 NV Logo, Blank Code Page Registration TSP100: Write to xml file. After registration: Settings on the Command Emulator are initialized to the xml file contents. operation + clear external character registration) TSP700II: Register only on Command Emulator memory. When PC power is turned off, data is erased. *2 Memory Switch TSP100: Write to xml file. (No self-print) Not written to printer, but printer is reset. TSP700II: Set only on Command Emulator memory. Not written to printer, but printer is reset. When PC power is turned off, setting is erased. 12
15 2-2) List of Compatible Models Class TSP100 TS- P700II Font Style and Character Set ESC RS F x x ESC GS t ESC GS = ESC R ESC / ESC SP ESC M ESC P ESC : ESC g Character expansion settings ESC i ESC W ESC h SO DC4 ESC SO ESC DC4 Print modes ESC E ESC F ESC - ESC _ ESC 4 ESC 5 SI DC2 Line spacing LF CR ESC a ESC z ESC 0 ESC J ESC I Page Control FF ESC C ESC C 0 VT ESC B Horizontal Direction Position ESC I ESC Q HT ESC D ESC GS A ESC GS R ESC GS a Download ESC & ESC % Model Name : OK x : NG 13
16 Class TSP100 TS- P700II Bit Image Graphics ESC K ESC L ESC k ESC X Logos ESC FS q ESC FS p Bar Codes ESC b Cutter control ESC d External Device Drive ESC BEL BEL FS SUB EM ESC GS BEL Print Setting ESC RS d ESC RS r Status ESC RS a x x ESC ACK SOH ENQ EOT ETB x x ESC RS E x x Chinese Character ESC p ESC q ESC $ ESC s ESC t ESC r Others CAN ESC GS # ESC? Raster ESC * r R x x ESC * r A x x ESC * r B x x ESC * r C x x ESC * r D x x ESC * r E x x ESC * r F x x ESC * r P x x ESC * r Q x x ESC * r m l x x ESC * r m r x x ESC * r T x x ESC * r K x x b n1 n2 d1 dk k n1 n2 d1 dk ESC * r Y x x ESC FF NUL x x ESC FF EOT x x x x x x x Model Name 14
17 Class TSP100 TS- P700II Black mark related commands ESC d x x FF x x ESC C x x ESC C 0 x x VT x x ESC B x x 2-Color Printing ESC RS c ESC RS C ESC 4 ESC 5 ESC RS d ESC RS r ESC FS q ESC FS p Presenter ESC SYN 0 x x ESC SYN 1 x x ESC SYN 3 x x ESC SYN 4 x x Mark ESC GS * 0 x x ESC GS * 1 x x ESC GS * 2 x x ESC GS * W x x ESC GS * C x x Auto Logo ESC GS / W x x ESC GS / C x x ESC GS / 1 x x ESC GS / 2 x x ESC GS / 3 x x ESC GS / 4 x x ESC GS / 5 x x ESC GS / 6 x x PDF417 ESC GS x S 0 x x ESC GS x S 1 x x ESC GS x S 2 x x ESC GS x S 3 x x ESC GS x D x x ESC GS x P x x ESC GS x I x x Print Start Trigger Control ESC GS g 0 x x ESC GS g 1 x x QR Code ESC GS y S 0 ESC GS y S 1 ESC GS y S 2 ESC GS y D 1 ESC GS y D 2 ESC GS y P ESC GS y I x x Model Name 15
18 SPECIAL PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsushinya, Shimizu-ku, Shizuoka, Japan Tel : Fax : OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC King Georges Post Road, Edison, NJ U.S.A. Tel : Fax : STAR MICRONICS U.K. LTD. Star House, Peregrine Business Park, Gomm Road, High Wycombe, Bucks, HP13 7DL, U.K. Tel : Fax : Please access the following URL for the lastest revision of the manual. Distributed by Rev Printed in Japan,
ESC/POS Command Specifications
Hybrid Printer ESC/POS Command Specifications Revision 0.00 Star Micronics Co., Ltd. Special Products Operating Division Contents 1) GENERAL DESCRIPTION 1-1 2) COMMAND FUNCTION LIST 2-1 3) COMMAND DETAILS
XR-500 [Receipt Printer User s Manual ]
![XR-500 [Receipt Printer User s Manual ]](/thumbs/40/21302789.jpg "XR-500 [Receipt Printer User s Manual ]")
XR-500 [Receipt Printer User s Manual ] All specifications are subjected to change without notice TABLE OF CONTENTS 1. Parts Identifications 2 2. Setting up the printer 3 2.1 Unpacking 3 2.2 Connecting
Thermal Control Board User Manual 1
Thermal Control Board User Manual 1 1 Outline... 2 2 HOW TO USE... 2 2.1 Printing test... 2 2.2 On board LED... 2 3 MECHANISM... 2 4 CONNECTOR... 3 5 ESC/POS PRINTING COMMAND SET... 3 5.1 Set of Command...
ASCII Code. Numerous codes were invented, including Émile Baudot's code (known as Baudot
ASCII Code Data coding Morse code was the first code used for long-distance communication. Samuel F.B. Morse invented it in 1844. This code is made up of dots and dashes (a sort of binary code). It was
How To Use A Microsoft Powerbook With A Microtron 2 (Ios) On A Microsatellite (Ipl) On An Iphone Or Ipro (Iphones) On Your Computer Or Ipo (Iphone)
MP-4000 TH Programmer's Manual Rev.1.4 August 2007 (First edition: November 2006) Copyright by Bematech S.A, Curitiba-PR, Brazil. All rights reserved. No part of this publication may be copied, reproduced,
[Format] [Range] [Default] [Description] The name of the command. The code sequence. [ ]k indicates the contents of the [ ] should be repeated k times. Gives the allowable ranges, if any, for the arguments.
WTP-150 Receipt Printer User s Manual
WTP-150 Receipt Printer User s Manual All specifications are subject to change without notice TABLE OF CONTENTS 1. Parts Identifications 3 2. Setting up the printer 4 2.1 Unpacking 4 2.2 Connecting the
Software Developer's Manual
Software Developer's Manual ESC/P Command Reference QL-720NW Version 1.0 The Brother logo is a registered trademark of Brother Industries, Ltd. Brother is a registered trademark of Brother Industries,
IBM Emulation Mode Printer Commands
IBM Emulation Mode Printer Commands Section 3 This section provides a detailed description of IBM emulation mode commands you can use with your printer. Control Codes Control codes are one-character printer
Xi2000 Series Configuration Guide
U.S. Default Settings Sequence Reset Scanner Xi2000 Series Configuration Guide Auto-Sense Mode ON UPC-A Convert to EAN-13 OFF UPC-E Lead Zero ON Save Changes POS-X, Inc. 2130 Grant St. Bellingham, WA 98225
Memory is implemented as an array of electronic switches
Memory Structure Memory is implemented as an array of electronic switches Each switch can be in one of two states 0 or 1, on or off, true or false, purple or gold, sitting or standing BInary digits (bits)
BAR CODE 39 ELFRING FONTS INC.
ELFRING FONTS INC. BAR CODE 39 This package includes 18 versions of a bar code 39 font in scalable TrueType and PostScript formats, a Windows utility, Bar39.exe, that helps you make bar codes, and Visual
CHAPTER 8 BAR CODE CONTROL
CHAPTER 8 BAR CODE CONTROL CHAPTER 8 BAR CODE CONTROL - 1 CONTENTS 1. INTRODUCTION...3 2. PRINT BAR CODES OR EXPANDED CHARACTERS... 4 3. DEFINITION OF PARAMETERS... 5 3.1. Bar Code Mode... 5 3.2. Bar Code
Voyager 9520/40 Voyager GS9590 Eclipse 5145
Voyager 9520/40 Voyager GS9590 Eclipse 5145 Quick Start Guide Aller à www.honeywellaidc.com pour le français. Vai a www.honeywellaidc.com per l'italiano. Gehe zu www.honeywellaidc.com für Deutsch. Ir a
Software Developer's Manual
Software Developer's Manual ESC/P Command Reference RJ-3050/3150 Version 1.00 The rother logo is a registered trademark of rother Industries, Ltd. rother is a registered trademark of rother Industries,
BARCODE READER V 2.1 EN USER MANUAL
BARCODE READER V 2.1 EN USER MANUAL INSTALLATION OF YOUR DEVICE PS-2 Connection RS-232 Connection (need 5Volts power supply) 1 INSTALLATION OF YOUR DEVICE USB Connection 2 USING THIS MANUAL TO SETUP YOUR
URL encoding uses hex code prefixed by %. Quoted Printable encoding uses hex code prefixed by =.
ASCII = American National Standard Code for Information Interchange ANSI X3.4 1986 (R1997) (PDF), ANSI INCITS 4 1986 (R1997) (Printed Edition) Coded Character Set 7 Bit American National Standard Code
Create!form Barcodes. User Guide
Create!form Barcodes User Guide Barcodes User Guide Version 6.3 Copyright Bottomline Technologies, Inc. 2008. All Rights Reserved Printed in the United States of America Information in this document is
DPP-250 Thermal Printer User Manual
1 DATECS DPP-250 Thermal Printer User Manual The information in this document cannot be reproduced in any mechanical, electrical or electronic way and under any circumstances without the written consent
Installing a Star Ethernet Printer with a Static IP Address on Windows 7/Vista/XP Using StarPRNT
Installing a Star Ethernet Printer with a Static IP Address on Windows 7/Vista/XP Using StarPRNT Introduction This application note shows how to install a Star Ethernet Printer with a static IP Address
Technical Reference DYMO LabelWriter SE450 Label Printer
Technical Reference DYMO LabelWriter SE450 Label Printer Copyright 2010 Sanford, L.P. All rights reserved. Revised 7/26/2010. No part of this document or the software may be reproduced or transmitted in
Software Development Kit Manual
Software Development Kit Manual Rev. 3.0 The company names and product names that appear in this manual are generally trademarks or registered trademarks of each company. Index 1. Status Monitor API...
Part No. : MUL-53221-07 PROGRAMMING GUIDE
Part No. : MUL-53221-07 PROGRAMMING GUIDE PROGRAMMING GUIDE for BARCODE SCANNERS The guide can be used as keyboard emulation, RS- 232C serial interface, and USB 1.1 interface and wand emulation. IMPORTANT
Addendum Advanced POS Printer Drivers
Addendum Advanced POS Printer Drivers Overview With the introduction of version 4.0, The General Store now supports the use of advanced, manufacturer s printer drivers for certain point of sale printers.
Windows Driver Manual SRP-330 Thermal printer Rev. 1.02
Windows Driver Manual SRP-330 Thermal printer Rev. 1.02 http://www.bixolon.com Table of Contents 1. Manual Information... 3 2. Operating System (OS) Environment... 3 3. Windows Driver Preparation... 3
Windows Driver Manual Metapace T-4 Thermal Printer Rev. 1.00
Manual Metapace T-4 Thermal Printer Rev. 1.00 http://www.metapace.com Table of Contents 1. Manual Information... 3 2. Operating System (OS) Environment... 3 3. Windows Driver Preparation... 3 4. Windows
Symbols in subject lines. An in-depth look at symbols
An in-depth look at symbols What is the advantage of using symbols in subject lines? The age of personal emails has changed significantly due to the social media boom, and instead, people are receving
CITIZEN OPOS DRIVER 1.8 Setup Guide. 10/03/29 Rev 1.09
CITIZEN OPOS DRIVER 1.8 Setup Guide 10/03/29 Rev 1.09 Revision Record Date Revision Description 07/12/21 Rev1.00 New issue 08/10/17 Rev1.01 Installer was changed. (Also related issues were modified.) CT-S281
BI-300. Barcode configuration and commands Manual
BI-300 Barcode configuration and commands Manual 1. Introduction This instruction manual is designed to set-up bar code scanner particularly to optimize the function of BI-300 bar code scanner. Terminal
plc numbers - 13.1 Encoded values; BCD and ASCII Error detection; parity, gray code and checksums
plc numbers - 3. Topics: Number bases; binary, octal, decimal, hexadecimal Binary calculations; s compliments, addition, subtraction and Boolean operations Encoded values; BCD and ASCII Error detection;
The ASCII Character Set
The ASCII Character Set The American Standard Code for Information Interchange or ASCII assigns values between 0 and 255 for upper and lower case letters, numeric digits, punctuation marks and other symbols.
DPP-350. ESC/POS Thermal Printer. Programmer s Manual 1 DATEC
DPP-350 ESC/POS Thermal Printer Programmer s Manual 1 DATEC Introduction DATECS DPP-350 is a mobile ESC/POS thermal printer with 3-inch wide printing mechanism. It can be used in dynamic working conditions
Manually Assigning an IP Address to a Star Ethernet Printer (Windows)
Manually Assigning an IP Address to a Star Ethernet Printer (Windows) Introduction This application note explains how to manually assign an IP Address to a Star Printer on a network without DHCP enabled.
Windows Driver Manual Metapace T-1. Thermal Printer Rev. 1.00
Windows Driver Manual Metapace T-1 Thermal Printer Rev. 1.00 Table of Contents 1. Manual Information...3 2. Operating System (OS) Environment...3 3. Windows Driver Preparation...3 4. Windows Driver Installation...4
Bar Code CCD Scanner OPERATION MANUAL
ISO 9002 Certified Lead with technology Win customers with service Bar Code CCD Scanner OPERATION MANUAL 69 Jarltech International Inc. 1998. All rights reserved. Under the copyright laws, this manual
Barcode Magstripe. Decoder & Scanner. Programming Manual
Barcode Magstripe Decoder & Scanner Programming Manual CONTENTS Getting Started... 2 Setup Procedures... 3 Setup Flow Chart...4 Group 0 : Interface Selection... 5 Group 1 : Device Selection for keyboard
DL910 SERIES. Instruction Manual
DL910 SERIES Instruction Manual DL910 SERIES INSTRUCTION MANUAL ALL RIGHTS RESERVED Datalogic reserves the right to make modifications and improvements without prior notification. Datalogic shall not
DEBT COLLECTION SYSTEM ACCOUNT SUBMISSION FILE
CAPITAL RESOLVE LTD. DEBT COLLECTION SYSTEM ACCOUNT SUBMISSION FILE (DCS-ASF1107-7a) For further technical support, please contact Clive Hudson (IT Dept.), 01386 421995 13/02/2012 Account Submission File
Enter/Exit programming
P/N: MUL-53247-02 Enter/Exit programming (This barcode is also found at back cover page.) Framed values are default values. All Rights Reserved This guide is designed for advanced settings of Hand Free
Application Note. How to configure WiFi Power Pack on Android Device. Introduction
How to configure WiFi Power Pack on Android Device Introduction Application Note Number: 271 This application note will show you how to setup the WiFi Power Pack to use with Star Printers on Android device.
MK-5200 2D Imager Barcode Scanner Configuration Guide
MK-5200 2D Imager Barcode Scanner Configuration Guide V 1.2 Programming the Engine Code Programming On/Off Read the barcode to activate Code Programming function. One or more Code Programming barcodes
ASCII CODES WITH GREEK CHARACTERS
ASCII CODES WITH GREEK CHARACTERS Dec Hex Char Description 0 0 NUL (Null) 1 1 SOH (Start of Header) 2 2 STX (Start of Text) 3 3 ETX (End of Text) 4 4 EOT (End of Transmission) 5 5 ENQ (Enquiry) 6 6 ACK
Numeral Systems. The number twenty-five can be represented in many ways: Decimal system (base 10): 25 Roman numerals:
Numeral Systems Which number is larger? 25 8 We need to distinguish between numbers and the symbols that represent them, called numerals. The number 25 is larger than 8, but the numeral 8 above is larger
Scanner Configuration
Scanner Configuration SmartScan Manual DOC Version 2.21 This document is specifically designed for the user to print two pages per sheet of paper with optimal print quality. Copyright 2005~ 2008 CIPHERLAB
The Lowest Cost, High Quality POS Printer THE TSP100 SERIES
The Lowest Cost, High Quality POS Printer THE TSP100 SERIES Welcome to the next generation in POS printe thermal receipt printer available today with Star Performance Print Speed vs Throughput Over the
Model 200 / 250 / 260 Programming Guide
Model 200 / 250 / 260 Programming Guide E-SEEK Inc. R & D Center 9471 Ridgehaven Court #E San Diego, CA 92123 Tel: 858-495-1900 Fax: 858-495-1901 Sales & Marketing 245 Fischer Ave #D5 Costa Mesa, CA 92626
S302D. Programming Guide. 2D Imaging Barcode Scanner. Advanced Handheld High-Speed Laser Scanner
S302D 2D Imaging Barcode Scanner Programming Guide 1 Advanced Handheld High-Speed Laser Scanner Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0
Index...1. Introduction...3. Installation- Keyboard Wedge...3 RS-232...3 USB...3. Default Setting for each barcode shown as below:...
Index Index...1 Introduction...3 Installation- Keyboard Wedge...3 RS-232...3 USB...3 Default Setting for each barcode shown as below:...4 Programming the MS320...5 Interface Selection...7 Keyboard wedge...8
Software Manual. for Mac OS X. Supported Models. TSP100 Series TSP650 Series TSP650II Series TSP700II Series TSP800II Series TSP1000 Series. Rev. 5.
Software Manual for Mac OS X Supported Models 100 Series 650 Series 650II Series 700II Series 800II Series 1000 Series Rev. 5.1 Notice: Mac, MacOS, MacBook, imac are trademarks of Apple Inc., registered
Model: LD1000 Series. USB Interface Customer Displays. 2 by 20 character display USER MANUAL. Rev 1.0
Model: LD1000 Series USB Interface Customer Displays 2 by 20 character display USER MANUAL Rev 1.0 i NOTICE The manufacturer of the POS pole display makes no representations or warranties, either expressed
CENTRONICS interface and Parallel Printer Port LPT
Course on BASCOM 8051 - (37) Theoretic/Practical course on BASCOM 8051 Programming. Author: DAMINO Salvatore. CENTRONICS interface and Parallel Printer Port LPT The Parallel Port, well known as LPT from
This is great when speed is important and relatively few words are necessary, but Max would be a terrible language for writing a text editor.
Dealing With ASCII ASCII, of course, is the numeric representation of letters used in most computers. In ASCII, there is a number for each character in a message. Max does not use ACSII very much. In the
Barcode Scanning Made Easy. WWS500 Programming Guide
Barcode Scanning Made Easy WWS500 Programming Guide Table of Contents Chapter 1. Introduction...........................2 Chapter 2. Barcode Symbologies...................3 Chapter 3. Quick Start............................4
How to Set Up Your PC for Android Application Development
Introduction Application Note How to Set Up Your PC for Android Application Development Supported Environments: Windows 7 (32/64-bit), Windows Vista (32/64-bit), Windows XP * This application note was
S PT-H500LI ELECTRONIC E C LABELING L SYSTEM INTRODUCTION EDITING A LABEL LABEL PRINTING USING THE FILE MEMORY USING P-TOUCH SOFTWARE
ELECTRONIC E C LABELING L SYSTEM S PT-H00LI In order to use your P-touch labeler safely, read the included Quick Setup Guide first. Read this guide before using your P-touch labeler. Keep this guide in
SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual
SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual Version 1.0 - January 20, 2015 CHANGE HISTORY Version Date Description of Changes 1.0 January 20, 2015 Initial Publication
Barcode Scanning Made Easy. Programming Guide
Barcode Scanning Made Easy Programming Guide CCD Scanner Programming Guide Please Read Note: The Wasp WCS3900 Series Scanners are ready to scan the most popular barcodes out of the box. This manual should
Software Developer's Manual
Software Developer's Manual P-touch Template 2.0 Command Reference RJ-4030/4040 Version 1.0 The Brother logo is a registered trademark of Brother Industries, Ltd. Brother is a registered trademark of Brother
Representação de Caracteres
Representação de Caracteres IFBA Instituto Federal de Educ. Ciencia e Tec Bahia Curso de Analise e Desenvolvimento de Sistemas Introdução à Ciência da Computação Prof. Msc. Antonio Carlos Souza Coletânea
Software User's Guide
Software User's Guide Brother QL-series The contents of this guide and the specifications of this product are subject to change without notice. Brother reserves the right to make changes without notice
Allen-Bradley. Bar Code. 2-D Hand-Held. Programming Guide. Bar Code. Scanners. (Cat. No. 2755-HTG-4)
Allen-Bradley 2-D Hand-Held Bar Code Scanners Bar Code Programming Guide (Cat. No. 2755-HTG-4) Important User Information The illustrations, charts, sample programs and layout examples shown in this guide
ios SDK API Reference Guide POS Printer
is SDK API Reference Guide PS Printer Rev. 2.00 SRP-F310 / SRP-F312 SRP-350plus / SRP-352plus SRP-350plusII / SRP-352plusII SRP-350II / SRP-350IIBE SRP-350III / SRP-352III SRP-275 / SRP-275II http://www.bixolon.com
How to Set Up Your PC for Android Application Development
Introduction Application Note How to Set Up Your PC for Android Application Development Supported Environments: Windows 7 (32/64 bit), Windows Vista (32/64 bit), Windows XP * This application note was
How To Use A Powerpoint On A Microsoft Powerpoint 2.5 (Powerpoint 2) With A Microsatellite 2.2 (Powerstation 2) (Powerplant 2.3) (For Microsonde) (Micros
SIM2 Multimedia Nero 3D-1, Nero 3D-2, Nero 3D HB RS-232 Control Rev. 1.1 (17 January 2012) Contents Contents 2 1 Introduction 3 1.1 Setting up the RS-232C Serial connection........................... 3
Chapter 1. Binary, octal and hexadecimal numbers
Chapter 1. Binary, octal and hexadecimal numbers This material is covered in the books: Nelson Magor Cooke et al, Basic mathematics for electronics (7th edition), Glencoe, Lake Forest, Ill., 1992. [Hamilton
Software User's Guide
PT-18R/PT-2430PC/PT-9600/ PT-9700PC/PT-9800PCN Software User's Guide The contents of this guide and the specifications of this product are subject to change without notice. Brother reserves the right to
24V DRIVE INTERFACE BOARD (SERIAL) FTP-622DSL001/011/012/112
24V DRIVE INTERFACE BOARD (SERIAL) FTP-622DSL001/011/012/112 FOR FTP-622/632/642MCL001/002/301/302/303/304 DESIGNATION SERIAL INTERFACE BOARD Product Part Number Function FTP-622DSL001 FTP-622DSL011 FTP-622DSL012
MK-SERIE 1000/1500/2000 AllOfBarcode.de Michael Krug - 83278Traunstein BARCODE SCANNER
MK-SERIE 1000/1500/2000 AllOfBarcode.de Michael Krug - 83278Traunstein BARCODE SCANNER Configuration Guide - 1 - Table of Contents Chapter 1 System Information 1.1 About this manual 3 1.2 How to set up
FTP-628WSL100/200 series
Battery drive, MOBILE type Compact standalone thermal printer 2 easy loading model FTP-628WSL100/200 series Overview The supply voltage of the FTP-628WSL Series is 120VAC (via AC adaptor) or battery. The
Software Developer's Manual
Software Developer's Manual Raster Command Reference PT-H500/P700/E500 Version 1.10 The Brother logo is a registered trademark of Brother Industries, Ltd. Brother is a registered trademark of Brother Industries,
BLE Series. Data setting software MEXE02 OPERATING MANUAL. Tabel of contents 1 Synchronization with the driver...2 2 Monitor function...
HP-5046 Data setting software MEXE02 BLE Series OPERATING MANUAL Thank you for purchasing an Oriental Motor product. This operating manual describes product handling procedures and safety precautions.
TM-U295/U295P. Using this online operator s guide. Operator s Manual
TM-U295/U295P Operator s Manual Using this online operator s guide The words on the left side of this screen are bookmarks for all the topics in this guide. Use the scroll bar next to the bookmarks to
NVT (Network Virtual Terminal) description
NVT (Network Virtual Terminal) description English version Czech version Communication with the TCP/IP device over the Ethernet network can be extended to more functions using NVT (Network Virtual Terminal)
python-escpos Documentation
python-escpos Documentation Release 1.0.8 Manuel F Martinez and others March 14, 2016 Contents 1 User Documentation: 3 2 API: 13 3 Indices and tables 17 Python Module Index 19 i ii Python ESC/POS is a
PRINTED MANUAL. 1999-2005 AGG Software (http://www.aggsoft.com)
PRINTED MANUAL Advanced Serial Port Monitor All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording,
Technical Reference Guide
Technical Reference Guide Product Overview Describes features and general specifications for the product. Setup Describes setup and instrallation of the product and peripherals. Application Development
PROPERTY MANAGEMENT SYSTEM
PROPERTY MANAGEMENT SYSTEM COMMUNICATION INTERFACE SPECIFICATION NEC America, Inc. NDA-305-00 Revision.0 June, 998 Stock # 24727 LIABILITY DISCLAIMER NEC America reserves the right to change the specifications,
Legal Notes. Regarding Trademarks. Model supported by the KX printer driver. 2010 KYOCERA MITA Corporation
Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change for improvement without notice. We cannot be held liable for any problems
LTM-1338B. Plus Communications Manual
LTM-1338B Plus Communications Manual 2000. Best Power, Necedah, Wisconsin All rights reserved. Best Power The System Setup option from the Main Menu on the front panel is passwordprotected. The default
Japanese Character Printers EPL2 Programming Manual Addendum
Japanese Character Printers EPL2 Programming Manual Addendum This addendum contains information unique to Zebra Technologies Japanese character bar code printers. The Japanese configuration printers support
CD-3860 Bar Code Scanner User s Manual
CD-3860 Bar Code Scanner User s Manual Important Notice Rev. Original No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or
HANDHELD LASER SCANNER
HANDHELD LASER SCANNER PROGRAMMING GUIDE PSC Scanning, Inc. En Suisse: 959 Terry Street GOMARO s.a. Eugene, Oregon 97402-9120 1123 Aclens - Switzerland Telephone: (541) 683-5700 http://www.gomaro.ch/ Toll
BRMO 80 / ETH-IP. User Manual. Réf : MU-BRMO 80-ETH-IP-1.4-EN
User Manual Réf : MU-BRMO 80-ETH-IP-1.4-EN BALOGH SA 189, rue d Aubervilliers - C.P. 97 75886 PARIS Cedex 18 France Tél : 33 (0)1 44 65 65 00 Fax : 33 (0)1 44 65 65 10 e-mail : balogh@balogh-group.com
Programming Guide. A799 Two-Color Thermal Receipt Printer. Includes TPG LogoEZ colorization information
A799 Two-Color Thermal Receipt Printer Programming Guide Includes TPG LogoEZ colorization information Made under one or more of the following U.S. patents: 4886381, 5579043, 5613787, 5651624, 5713678,
OralChroma OralChroma DataManager
OralChroma OralChroma DataManager User s Guide for Windows Version 3.5 Introduction This is a user s manual for the OralChroma DataManager. Copyright Copyright (C) 2008- ABIMEDICAL CORPORATION. All Rights
Chapter 5. Binary, octal and hexadecimal numbers
Chapter 5. Binary, octal and hexadecimal numbers A place to look for some of this material is the Wikipedia page http://en.wikipedia.org/wiki/binary_numeral_system#counting_in_binary Another place that
Bar Code Reader Models 1000/1002 USER'S MANUAL 2190 Regal Parkway Euless, TX 76040 (817) 571-9015 (800) 648-4452 FAX (817) 685-6232 FCC NOTICE WARNING: This equipment generates, uses and can radiate radio
Barcode reader setup manual
Barcode reader setup manual Setup procedures are as follows: 1 Scan Begin setting 2 Scan your required function and its corresponding barcode 3 Scan End setting 4 All the setting parameters will be saved
2 ASCII TABLE (DOS) 3 ASCII TABLE (Window)
1 ASCII TABLE 2 ASCII TABLE (DOS) 3 ASCII TABLE (Window) 4 Keyboard Codes The Diagram below shows the codes that are returned when a key is pressed. For example, pressing a would return 0x61. If it is
DT105X / PB105 Series
DT105 / Series Cash Drawer Trigger & Printer Beeper User's Manual TM951031-05 Contents Information... 1 Technical And Operational Description... 3 Connections Load Test Specifications......... 5 7 8 Communication
Software Installation Manual
unified, multi-model driver and configuration suite Software Installation Manual Rev. 3.2 Contents 1. Software Overview... 1 1.1 Windows Driver...1 1.2 Utility...2 1.2.1 Starting the Utility...2 1.2.2
With a barcode reader connected to the printer, labels and barcodes can easily be printed by scanning barcodes.
With a barcode reader connected to the printer, labels and barcodes can easily be printed by scanning barcodes. Connect a barcode reader to the printer to create a label or barcode using "P-touch Editor
MINIMAG. Magnetic Stripe Reader Keyboard Wedge. User s Manual
MINIMAG Magnetic Stripe Reader Keyboard Wedge User s Manual TM Agency Approved Specifications for subpart B of part 15 of FCC rule for a Class A computing device. Limited Warranty ID TECH warrants to the
4) How many peripheral devices can be connected to a single SCSI port? 4) A) 8 B) 32 C) 1 D) 100
FALL 07-08 COMP100 MIDTERM-2 EXAM /FACULTY OF ECON. AND ADMINISTRATIVE SCIENCES OF EUL Student Registration No: Instructor: Prof.Dr.Hüseyin Oğuz Student Name-Surname: Dept. of Computer Information Systems
FTP-628WSL100/200-R series
Battery drive, MOBILE type Compact standalone thermal printer 2 easy loading model FTP-628WSL100/200-R series Overview The supply voltage of the FTP-628WSL Series is 120/240VAC (via AC adaptor) or battery.
KX Driver Version 4.1. User Guide
KX Driver Version 4. User Guide Legal Notes Unauthorized reproduction of all or part of this guide is prohibited. The information in this guide is subject to change for improvement without notice. We cannot
ASCII control characters (character code 0-31)
ASCII control characters (character code 0-31) DEC HEX 0 00 NUL Null char 1 01 SOH Start of Heading 2 02 STX Start of Text 3 03 ETX End of Text 4 04 EOT End of Transmission
BAR CODE CONTROL BAR CODE CONTROL - 1
BAR CODE CONTROL BAR CODE CONTROL - 1 CONTENTS 1. INTRODUCTION... 3 2. PRINT BAR CODES OR EXPANDED CHARACTERS... 4 3. DEFINITION OF PARAMETERS... 5 3.1. Bar Code Mode............ 5 3.2. Bar Code Style,
TELOCATOR ALPHANUMERIC PROTOCOL (TAP)
TELOCATOR ALPHANUMERIC PROTOCOL (TAP) Version 1.8 February 4, 1997 TABLE OF CONTENTS 1.0 Introduction...1 2.0 TAP Operating Environment...1 3.0 Recommended Sequence Of Call Delivery From An Entry Device...2
Win 7 - STIMA CLS / CMP Driver Installation Quick Guide
Win 7 - STIMA CLS / CMP Driver Installation Quick Guide This guide is intended to demonstrate a quick installation and setup of ticket alignment under Windows 7 for the Stima CLS and CMP printers using