INSTRUMENTS INSTRUMENTS INSTRUMENT SETS - FLAGSHIP PLUS BLACK FACE FAMILY

Transcription

1 INSTRUMENT SETS - FLAGSHIP PLUS BLACK FACE FAMILY Visit the Flagship Plus Black Face Family Gauges section for individual details. All tachometers and speedometers fit a standard 3 3/8 in. (85 mm) diameter hole. All other gauges fit a 2 1/8 in. (54 mm) diameter hole. information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 409

2 INSTRUMENT SETS - FLAGSHIP PLUS WHITE FACE FAMILY Visit the Flagship Plus White Face Family Gauges section for individual details. All tachometers and speedometers fit a standard 3 3/8 in. (85 mm) diameter hole. All other gauges fit a 2 1/8 in. (54 mm) diameter hole Quicksilver Precision Parts & Accessories Guide

3 ANALOG GAUGE INTERFACE - DIGITAL ENGINES Converts digital signal to analog ANALOG GAUGE INTERFACE KIT PITOT SENSOR KIT 8M Components needed to add pitot for speedometer gauges Stroke Engines WARER PRESSURE KIT 8M Components needed to water pressure gauges Stroke Engines ANALOG WATER PRESSURE FITTING KIT 32-8M Fitting kit to install analog gauge to engine. 150 HP 4 Stroke K08 This kit allows the conversion of a digital signal to an analog signal. (Verado engines are on digital platform and this kit must use with analog gauge installations) 2005 and newer Verado HOSE KIT MONITOR PANELS FOR DIESELS PRIMARY STATION MONITOR PANEL A01 Contains the necessary tubing, tee fitting and instruction sheet to allow the use of a 15 PSI Analog Water Pressure Gauge with the otherwise digital 1.5L OptiMax outboard. Fits the 75/90/115hp (1.5L) OptiMax Outboard Engine, Model Year 2004 and newer. CONVERSION KIT - SMARTCRAFT SENSORS T Warning lights are provided for low oil pressure, excessive coolant temperature, insufficient alternator output and glow plug activation. Fits 1.7L MS & MI 120 and 4.2 MS & MI (200 & 230) PRIMARY STATION MONITOR PANEL Warning lights are provided for low oil pressure, excessive coolant temperature, insufficient alternator output, glow plug activation & check engine light. Fits 1997 and newer 2.8 ES & EI 165 and 4.2 ES & EI (250 & 230) K01 New kit that allows you to use SmartCraft gauges on these engines Gen II (2007) 75 HP 115 HP 4 stroke engines and newer engines TRIM SENSOR CONVERTER KIT 8M This kit will allow you to convert the signal from the digital sensor to an analog signal. It will allow you to drive an analog gauge for trim only without changing the sensor to an analog sensor. This kit will connect directly to the harness inside the emgine cowl. 150 HP 4 Stroke engine only information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 411

4 SECOND STATION MONITOR PANEL SECOND STATION MONITOR PANEL This panel is virtually identical to primary station monitor panel, except it has locations for toggle switches for starting and stopping instead of a key switch. Fits 1.7 MS & MI 120 and 4.2 MS & MI (200 & 230) This panel is virtually identical to primary station panel, except it has locations for toggle switches for starting and stopping instead of a key switch. Fits 1997 and newer 2.8 ES & EI 165 and 4.2 ES & EI (250 & 300) TACHOMETER SELECTION AND SETTINGS CHARTS Tachometer Application Model Description Flagship (Black Face) Flagship (White Face) Generic MerCruiser MCM/MIE Gasoline Engines 6000 RPM A A23 N/A 8000 RPM A A11 N/A MerCruiser D1.7L DTI, D2.8L & D4.2L D-tronic ALL A A23 N/A MerCruiser D3.0, D3.6L & D4.2L 1994 and Newer A 1 N/A N/A MerCruiser D7.3L D-Tronic 1997 and Newer A 1 N/A N/A Mercury/Mariner 4-Stroke Outboards 6000 RPM A A23 N/A 8000 RPM A A11 N/A Mercury/Mariner 20 HP and Above (2 cycle) 6000 RPM A A23 N/A 8000 RPM A A11 N/A Mercury/Mariner Optimax 6000 RPM(1) A A23 N/A 8000 RPM(1) A A11 N/A Mariner 8-40 HP (Japanese import) Manual start w/ lighting coil N/A N/A N/A Mariner HP (Japanese import) Electric start / 2 cylinder N/A N/A N/A Force 3 50cc N/A N/A A 1 Force 40 HP and Above 6000 RPM A A23 N/A 8000 RPM A A11 N/A (1) Correct harness required for optimum performance Tachometer Settings Model Country Serial # Range Positive Pulses Per Crank Revolution Poles Flagship (Force A 1) Tachometer Switch Setting Mercury/Mariner (2-stroke) 6 thru 25 HP (U.S. Orig 4 8 4P N/A Mercury/Mariner (4-stroke) 8 and 9.9 HP 3 6 3P N/A Mercury/Mariner (2-stroke) 30/40 HP USA 0G and up P N/A Mercury/Mariner 35 and 40 HP (2 Cyl.) USA and up 4 8 4P N/A BEL and up 4 8 4P N/A AUS and up 4 8 4P N/A CAN and up 4 8 4P N/A Mercury/Mariner (4-stroke) 25 thru 90 HP P N/A Mercury/Mariner (2-stroke) 45 thru V-6 (U.S. Origi P N/A Force N/A 1 Force 35 HP and higher with Mercury ignition P 2 MerCruiser 4 cyl. gasoline engine 2 N/A 4C N/A MerCruiser 6 cyl. gasoline engine 3 N/A 6C N/A MerCruiser 8 cyl. gasoline engine 4 N/A 8C N/A Quicksilver Precision Parts & Accessories Guide

5 FLAGSHIP PLUS BLACK FACE FAMILY FLAGSHIPTACHOMETER KIT Large gauge fits 3 3/8 in.(86 mm) hole in dash. Small gauge fits 2 1/8 in.(54 mm) hole in dash. 12 volt system. Tachometer selection and settings charts are located following the color group images. FLAGSHIP INSTRUMENT SET A01 Anti fog lens. Black face and black bezel; blue graduations. Set includes RPM tachometer, oil pressure gauge, battery meter and water temperature gauge. All illuminated. Mounting hardware also included. For sterndrives and inboards only with 12 volt system. FLAGSHIPTACHOMETER KIT A05 Anti fog lens RPM. 270 degree dial sweep. Black face and Black bezel: Blue graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. Fits 3 3/8 in. (85 mm) hole in dash. For various Mercury Outboards and MCM products. Will require AGI converter with Verado (Digital) engines FLAGSHIPTACHOMETER KIT A02 Anti fog lens RPM. 270 degree dial sweep. Black face and Black bezel: Blue graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. Fits 3 3/8 in. (85 mm) hole in dash. Diesel Engines only FLAGSHIPTACHOMETER KIT A06 Anti fog lens RPM. 270 degree dial sweep. Black face and Black bezel: Blue graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. Fits 3 3/8 in. (85 mm) hole in dash. for various Mercury Outboards and MCM products. Will require AGI converter with Verado (Digital) engines FLAGSHIP SPEEDOMETER A03 Anti fog lens RPM. 270 degree dial sweep. Black face and Black bezel: Blue graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. Fits 3 3/8 in. (85 mm) hole in dash. For various Mercury Outboard and MCM products. Will require AGI converter for Verado (Digital) engines A01 Anti fog lens MPH. 270 degree dial sweep. Black face and Black bezel; White/Blue graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (86 mm) hole in dash. information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 413

6 FLAGSHIP SPEEDOMETER FLAGSHIP SPEEDOMETER A03 Anti fog lens MPH. 270 degree dial sweep. Black face and Black bezel; White/Blue graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. FLAGSHIP SPEEDOMETER A08 Anti fog lens knots. 270 degree dial sweep. Black face and Black bezel; White/Blue graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. DIGITAL DEPTH GAUGE KIT A04 Anti fog lens MPH. 270 degree dial sweep. Black face and Black bezel; White/Blue graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. FLAGSHIP SPEEDOMETER A01 Black face and black bezel. Digital depth readout to 199 feet, display is backlit for night operation. Easy addition to any boat. Fits in a cutout for standard 2 in.(51 mm) gauge. Kit includes adjustable alarm, transom mounted/inside hull mounted transducer. Easy to follow instructions. The affordable way to add more fun and safety to boating. Available in Multiple bezel colors BEZEL 52 MM A06 Anti fog lens MPH. 270 degree dial sweep. Black face and Black bezel; White/Blue graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash Bezel Gold 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only Quicksilver Precision Parts & Accessories Guide

7 BEZEL 52 MM FLAGSHIP WATER TEMPERATURE GAUGE Bezel Chrome 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only FLAGSHIP VOLT METER A02 Anti fog lens. 60 deg. 200 deg.f gauge. Black face and Black bezel; White/Blue graduations. Fits Mercury/Mariner 25 thru 115 FourStroke, 225 FourStroke, 40 (3 & 4 cyl.), 45, 50/60 (3 cyl.), and 70 to 125 hp ; and 1993 and newer Force outboards (Force models must order sender FA299791) Sender need to be ordered seperately FLAGSHIP WATER TEMPERATURE GAUGE A01 Anti fog lens. Black face and Black bezel; White/Blue graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. FLAGSHIP WATER TEMPERATURE GAUGE A03 Anti fog lens. 100 deg. 240 deg.f gauge. Black face and Black bezel; White/Blue graduations. Diesel FLAGSHIP WATER PRESSURE GAUGE A01 Anti fog lens. 120 deg. 240 deg.f gauge. Black face and Black bezel; White/Blue graduations. Fits all MCM/MIE gasoline engines and Mercury/Mariner V 6 outboards. Sender, if not already installed on the outboard, must be purchased separately A01 Anti fog lens. 1 to 15 psi gauge with quick connect terminals for connection to light. Black face and bezel; blue graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits Mercury/Mariner 25 E and EL (U.S. S/N 0C and above; Belgium S/N and above), 30 to 125 (except four stroke models), 1998 and older V 6 (3.0L), and Force 40/ A02 Anti fog lens. 1 to 15 psi gauge with quick connect terminals for connection to light. Black face and bezel; blue graduations. Replacement gauge only Fits Mercury/Mariner 25 E and EL (U.S. S/N 0C and above; Belgium S/N and above), 30 to 125 (except four stroke models), 1998 and older V 6 (3.0L), and Force 40/50. information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 415

8 FLAGSHIP WATER PRESSURE GAUGE FLAGSHIP WATER PRESSURE GAUGE A03 Anti fog lens. 2 to 30 psi gauge with quick connect terminals for connection to light. Black face and Black bezel with Blue/White graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits Mercury/Mariner 25/30/40/45/50/75/90/115/225 (4 stroke), all V 6 (except 3.0L 1998 and older) ; and Force 75, 90 and 120. The 75/90/115/225 FourStroke outboards require a reducer fitting p/n A04 Anti fog lens. 2 to 30 psi gauge with quick connect terminals for connection to light. Black face and Black bezel with Blue/White graduations. Replacement Gauge only Fits Mercury/Mariner 25/30/40/45/50/75/90/115/225 (4 stroke), all V 6 (except 3.0L 1998 and older) ; and Force 75, 90 and 120. The 75/90/115/225 FourStroke outboards require a reducer fitting p/n FLAGSHIP WATER PRESSURE GAUGE A06 Anti fog lens. 2 to 40 psi gauge with quick connect terminals for connection to light. Black face and bezel; blue graduations.. Replacement gauge only. Fits hp EFI FourStroke Outboards, serial number 1B & above. FLAGSHIP OIL PRESSURE GAUGE A01 Anti fog lens. Black face and Black bezel; Blue/White graduations. Fits all MCM/MIE gasoline engines and Mercury/Mariner 25/30/40/45/50/225 (4 stroke) outboards. Sender, if not already installed on the outboard, must be purchased separately. FLAGSHIP OIL PRESSURE GAUGE A05 Anti fog lens. 2 to 40 psi gauge with quick connect terminals for connection to light. Black face and bezel; blue graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits hp EFI FourStroke Outboards, serial number 1B & above. LAGREE FITTING FOR 2-40 PSI- WATER PRESSURE A02 Anti fog lens. Black face and Black bezel; Blue / White graduations. Fits D3.0L, D3.6L, and 4.2L diesels (1994 & newer) and D2.8, D4.2L, and D7.3L ES & EI models (1997 & newer) A01 Fitting that connects to block to hook up Water pressure gauge. This fitting is included in the 40 psi gauge "kit". Fits hp EFI FourStroke outboards, serial number 1B & above Quicksilver Precision Parts & Accessories Guide

9 FLAGSHIP OIL LEVEL GAUGE KIT FLAGSHIP POWER TRIM GAUGE A01 Anti fog lens. Black face and Black bezel; Blue/White graduations. Fits V 6 outboard 3 US gal.(11.34 L) and 1.8 US gal.(6.8 L) remote oil reservoirs. FLAGSHIP FUEL GAUGE A01 Anti fog lens. Black face and bezel; blue graduations. Designed for models that have a sender already installed or installation of a sender kit purchased separately. Fits Sterndrive and Outboards FLAGSHIP DUAL ENGINE SYNCHRONIZER A01 Anti fog lens. Black face and Blue bezel; black graduations. 12 volt system and 240 ohm sender required. FUEL GAUGE SENDING UNIT A01 Anti fog lens. Black face and Black bezel; Blue/White graduations. Connects to tachometers. Fits both 2 stroke and 4 stroke gasoline engine applications. SYNCHRONIZEER DRIVER - GAUGES Q Designed for tanks that have a 5 screw flange. Use with 12 volt system ohm. Adjusts from 4 in.(10.2 cm) to 24 in.(60.7 cm) Quicksilver Branded, Clamshell Package Point of Sale Packaged. 8M This product is used with the analog gauge to synchronize multilpe engines. Any Admiral,Flagship or International II gauges information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 417

10 FLAGSHIP CRUISELOG GAUGE FLAGSHIPTACHOMETER KIT A01 Anti fog lens. Black face and Black bezel; blue graduations. No illumination. Wiring included with this single pack. FLAGSHIP CLOCK A22 Anti fog lens RPM. 270 degree dial sweep. White face and White bezel: Black graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. Fits 3 3/8 in. (85 mm) hole in dash. Diesel Engines only FLAGSHIPTACHOMETER KIT A01 Anti fog lens. Black face and Black bezel; black graduations. Wiring is not included. FLAGSHIP PLUS WHITE FACE FAMILY Large gauge fits 3 3/8 in.(86 mm) hole in dash. Small gauge fits 2 1/8 in.(54 mm) hole in dash. 12 volt system. Tachometer selection and settings charts are located following the color group images A23 Anti fog lens RPM. 270 degree dial sweep. White face and White bezel: Black graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. Fits 3 3/8 in. (85 mm) hole in dash. For various Mercury Outboards and MCM produts. Will require the use of AGI converter for Verado (Digital) engines FLAGSHIPTACHOMETER KIT FLAGSHIP INSTRUMENT SET A21 Anti fog lens. White face and white bezel; black graduations. Set includes RPM tachometer, oil pressure gauge, battery meter and water temperature gauge. All illuminated. Mounting hardware also included. For various Mercury Outbord and MCM products. Will require an AGI converter for Verado (Ditgital) engines A25 Anti fog lens RPM. 270 degree dial sweep. White face and White bezel: Black graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. Fits 3 3/8 in. (85 mm) hole in dash. For various Mercury Outboards and MCM product. Will require use of AGI converter for Verado (Digital) engines Quicksilver Precision Parts & Accessories Guide

11 FLAGSHIPTACHOMETER KIT FLAGSHIP SPEEDOMETER A26 Anti fog lens RPM. 270 degree dial sweep. White face and White bezel: Black graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. Fits 3 3/8 in. (85 mm) hole in dash. For various Mercury Outboards and MCM products. Will require the use of an AGI converter with Verado (Digital) engiens. FLAGSHIP SPEEDOMETER A24 Anti fog lens MPH. 270 degree dial sweep. White face and White bezel; Black graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. FLAGSHIP SPEEDOMETER A21 Anti fog lens MPH. 270 degree dial sweep. White face and White bezel; Black graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. FLAGSHIP SPEEDOMETER A26 Anti fog lens MPH. 270 degree dial sweep. White face and White bezel; Black graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. FLAGSHIP SPEEDOMETER A23 Anti fog lens MPH. 270 degree dial sweep. White face and White bezel; Black graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash A28 Anti fog lens Knots. 270 degree dial sweep. White face and White bezel; Black graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 419

12 DIGITAL DEPTH GAUGE KIT FLAGSHIP VOLT METER A02 White face and white bezel. Digital depth readout to 199 feet, display is backlit for night operation. Easy addition to any boat. Fits in a cutout for standard 2 in.(51 mm) gauge. Kit includes adjustable alarm, transom mounted/inside hull mounted transducer. Easy to follow instructions. The affordable way to add more fun and safety to boating. Available in multiple bezel colors BEZEL 52 MM A21 Anti fog lens. White face and White bezel; black graduations. Outboards require a tachometer harness or ignition/choke assembly for connection. FLAGSHIP WATER TEMPERATURE GAUGE Bezel Gold 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only BEZEL 52 MM A21 Anti fog lens. 100 deg. 240 deg.f gauge. White face and White bezel; Black graduations. Fits all MCM/MIE gasoline engines and Mercury/Mariner V 6 outboards. Sender, if not already installed on the outboard, must be purchased separately. FLAGSHIP WATER TEMPERATURE GAUGE Bezel Chrome 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only A22 Anti fog lens. 60 deg. 200 deg.f gauge. White face and White bezel; Black graduations. Fits Mercury/Mariner 25 thru 115 FourStroke, 225 FourStroke, 40 (3 & 4 cyl.), 45, 50/60 (3 cyl.), and 70 to 125 hp ; and 1993 and newer Force outboards (Force models must order sender FA299791) Senders must be ordered seperately Quicksilver Precision Parts & Accessories Guide

13 FLAGSHIP WATER TEMPERATURE GAUGE A24 Anti fog lens. 2 to 30 psi gauge with quick connect terminals for connection to light. White face and White bezel; Black graduations. Replacement gauge only Fits Mercury/Mariner 25/30/40/45/50/75/90/115/225 (4 stroke), all V 6 (except 3.0L 1998 and older) ; and Force 75, 90 and 120. The 75/90/115/225 FourStroke outboards require a reducer fitting p/n FLAGSHIP WATER PRESSURE GAUGE A23 Anti fog lens. 100 deg. 240 deg.f gauge. White face and White bezel; Black graduations. Diesel FLAGSHIP WATER PRESSURE GAUGE A25 Anti fog lens. 2 to 40 psi gauge with quick connect terminals for connection to light. White face and bezel; black graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits hp EFI FourStroke Outboards, serial number 1B & above. LAGREE FITTING FOR 2-40 PSI- WATER PRESSURE A21 Anti fog lens. 1 to 15 psi gauge with quick connect terminals for connection to light. White face and bezel; black graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits Mercury/Mariner 25 E and EL (U.S. S/N 0C and above; Belgium S/N and above), 30 to 125 (except four stroke models), 1998 and older V 6 (3.0L), and Force 40/ A22 Anti fog lens. 1 to 15 psi gauge with quick connect terminals for connection to light. White face and bezel; Black graduations. Replacement gauge only Fits Mercury/Mariner 25 E and EL (U.S. S/N 0C and above; Belgium S/N and above), 30 to 125 (except four stroke models), 1998 and older V 6 (3.0L), and Force 40/50. FLAGSHIP WATER PRESSURE GAUGE A01 Fitting that connects to block to hook up Water pressure gauge. This fitting is included in the 40 psi gauge "kit". Fits hp EFI FourStroke outboards, serial number 1B & above. FLAGSHIP WATER PRESSURE GAUGE A23 Anti fog lens. 2 to 30 psi gauge with quick connect terminals for connection to light. White face and bezel; black graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits Mercury/Mariner 25/30/40/45/50/75/90/115/225 (4 stroke), all V 6 (except 3.0L 1998 and older) ; and Force 75, 90 and 120. The 75/90/115/225 FourStroke outboards require a reducer fitting p/n A26 Anti fog lens. 2 to 40 psi gauge with quick connect terminals for connection to light. White face and White bezel; Black graduations. Replacement gauge only Fits hp EFI FourStroke Outboards, serial number 1B & above. information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 421

14 FLAGSHIP OIL PRESSURE GAUGE FLAGSHIP FUEL GAUGE A21 Anti fog lens. White face and White bezel; black graduations. Fits all MCM/MIE gasoline engines and Mercury/Mariner 25/30/40/45/50/225 (4 stroke) outboards. Sender, if not already installed on the outboard, must be purchased separately. FLAGSHIP OIL PRESSURE GAUGE A21 Anti fog lens. White face and White bezel; black graduations. 12 volt system and 240 ohm sender required. FUEL GAUGE SENDING UNIT A22 Anti fog lens. White face and White bezel; black graduations. Fits D3.0L, D3.6L, and 4.2L diesels (1994 & newer) and D2.8, D4.2L, and D7.3L ES & EI models (1997 & newer). FLAGSHIP OIL LEVEL GAUGE KIT Q Designed for tanks that have a 5 screw flange. Use with 12 volt system ohm. Adjusts from 4 in.(10.2 cm) to 24 in.(60.7 cm) Quicksilver Branded, Clamshell Package Point of Sale Packaged. FLAGSHIP POWER TRIM GAUGE A21 Anti fog lens. White face and White bezel; black graduations. Fits V 6 outboard 3 US gal.(11.34 L) and 1.8 US gal.(6.8 L) remote oil reservoirs A21 Anti fog lens. White face and bezel; black graduations. Designed for models that have a sender already installed or installation of a sender kit purchased separately. Fits Sterndrives and Outboards Quicksilver Precision Parts & Accessories Guide

15 FLAGSHIP DUAL ENGINE SYNCHRONIZER INTERNATIONAL II FAMILY GAUGES Large gauge fits 3 3/8 in.(86 mm) hole in dash. Small gauge fits 2 1/8 in.(54 mm) hole in dash. 12 volt system. Tachometer selection and settings charts are located following the color group images. INTERNATIONAL II SPEEDOMETER A21 Anti fog lens. White face and White bezel; black graduations. Connects to tachometers. Fits both 2 stroke and 4 stroke gasoline engine applications. SYNCHRONIZEER DRIVER - GAUGES 8M This product is used with the analog gauge to synchronize multilpe engines. Any Admiral,Flagship or International II gauges FLAGSHIP CRUISELOG GAUGE Q41 Anti fog lens MPH. 270 degree dial sweep. Black face and black bezel; orange/white graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. Quicksilver Branded, Box Point of Sale Packaged Q43 Anti fog lens MPH. 270 degree dial sweep. Black face and blackbezel; orange/white graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. Quicksilver Branded, Box Point of Sale Packaged. INTERNATIONAL II SPEEDOMETER A21 Anti fog lens. White face and White bezel; black graduations. No illumination. Wiring included with this single pack. FLAGSHIP CLOCK Q44 Anti fog lens MPH. 270 degree dial sweep. Black face and black bezel; orange/white graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. Quicksilver Branded, Box Point of Sale Packaged. INTERNATIONAL II SPEEDOMETER A21 Anti fog lens. White face and White bezel; black graduations. Wiring is not included Q48 Anti fog lens Knots. 270 degree dial sweep. Black face and black bezel; orange/white graduations. Includes 20 ft.(6.1 m) of tubing. Fits 3 3/8 in. (85 mm) hole in dash. Quicksilver Branded, Box Point of Sale Packaged. information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 423

16 INTERNATIONAL II WATER TEMPERATURE GAUGE Q44 Anti fog lens. 2 to 30 psi gauge with quick connect terminals for connection to light. Black face and Black bezel; Orange graduations. Service replacement gauge. Fits Mercury/Mariner 25/30/40/45/50/75/90/115/225 (4 stroke), all V 6 (except 3.0L 1998 and older) ; and Force 75, 90 and 120. The 75/90/115/225 FourStroke outboards require a reducer fitting p/n Quicksilver Branded, Box Point of Sale Packaged. INTERNATIONAL II WATER PRESSURE GAUGE Q41 Anti fog lens. 100 deg. 240 deg.f gauge. Black face and Black bezel; Orange/ White graduations. Fits all MCM/MIE gasoline engines and Mercury/Mariner V 6 outboards. Sender, if not already installed on the outboard, must be purchased separately. Quicksilver Branded, Box Point of Sale Packaged. INTERNATIONAL II WATER PRESSURE GAUGE Q41 Anti fog lens. 1 to 15 psi gauge with quick connect terminals for connection to light. Black face and Black bezel; Orange graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits Mercury/Mariner 25/30/40/45/50/75/90/115/225 (4 stroke), all V 6 (except 3.0L 1998 and older) ; and Force 75, 90 and 120. The 75/90/115/225 FourStroke outboards require a reducer fitting p/n Quicksilver Branded, Box Point of Sale Packaged Q42 Anti fog lens. 1 to 15 psi gauge with quick connect terminals for connection to light. Black face and Black bezel; Orange graduation. Service replacement gauge. Fits Mercury/Mariner 25/30/40/45/50/75/90/115/225 (4 stroke), all V 6 (except 3.0L 1998 and older) ; and Force 75, 90 and 120. The 75/90/115/225 FourStroke outboards require a reducer fitting p/n Quicksilver Branded, Box Point of Sale Packaged. INTERNATIONAL II WATER PRESSURE GAUGE Q45 Anti fog lens. 2 to 40 psi gauge with quick connect terminals for connection to light. Black face and Black bezel; Orange graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits hp EFI FourStroke Outboards, serial number 1B & above. Quicksilver Branded, Box Point of Sale Packaged Q46 Anti fog lens. 2 to 40 psi gauge with quick connect terminals for connection to light. Black face and Black bezel; Orange graduations. Replacement gauge only. Fits hp EFI FourStroke Outboards, serial number 1B & above. Quicksilver Branded, Box Point of Sale Packaged. INTERNATIONAL II FUEL GAUGE Q41 Anti fog lens. Black face and Black bezel; Oraqnge/White graduations. Bulk Package of 24 pcs. 12 volt system and 240 ohm sender required. Quicksilver Branded, Box Point of Sale Packaged. FUEL GAUGE SENDING UNIT Q43 Anti fog lens. 2 to 30 psi gauge with quick connect terminals for connection to light. Black face and Black bezel; Orange graduations. Complete kit. Includes 25 ft.(7.6 m) of tubing and hardware. Replacement hose not sold separate, obtain locally. Fits Mercury/Mariner 25/30/40/45/50/75/90/115/225 (4 stroke), all V 6 (except 3.0L 1998 and older) ; and Force 75, 90 and 120. The 75/90/115/225 FourStroke outboards require a reducer fitting p/n Quicksilver Branded, Box Point of Sale Packaged Q Designed for tanks that have a 5 screw flange. Use with 12 volt system ohm. Adjusts from 4 in.(10.2 cm) to 24 in.(60.7 cm) Quicksilver Branded, Clamshell Package Point of Sale Packaged Quicksilver Precision Parts & Accessories Guide

17 INTERNATIONAL II TRIM GAUGE INTERNATIONAL II CLOCK Q41 Anti fog lens. Black face and Black bezel; Orange/White graduations. 12 volt system Quicksilver Branded, Box Point of Sale Packaged. INTERNATIONAL II DUAL ENGINE SYNCHRONIZER Q41 Anti fog lens. Black face and Black bezel; Orange/White graduations. Wiring is included in this single pack. Quicksilver Branded, Box Point of Sale Packaged. DEPTH SOUNDERS DIGITAL DEPTH GAUGE KIT Q41 Anti fog lens. Black face and Black bezel; Orange/White graduations. Connects to tachometers. Fits both 2 stroke and 4 stroke gasoline engine applications. Quicksilver Branded, Box Point of Sale Packaged. SYNCHRONIZEER DRIVER - GAUGES A01 Black face and black bezel. Digital depth readout to 199 feet, display is backlit for night operation. Easy addition to any boat. Fits in a cutout for standard 2 in.(51 mm) gauge. Kit includes adjustable alarm, transom mounted/inside hull mounted transducer. Easy to follow instructions. The affordable way to add more fun and safety to boating. Available in Multiple bezel colors DIGITAL DEPTH GAUGE KIT 8M This product is used with the analog gauge to synchronize multilpe engines. Any Admiral,Flagship or International II gauges INTERNATIONAL II CRUISELOG GAUGE A02 White face and white bezel. Digital depth readout to 199 feet, display is backlit for night operation. Easy addition to any boat. Fits in a cutout for standard 2 in.(51 mm) gauge. Kit includes adjustable alarm, transom mounted/inside hull mounted transducer. Easy to follow instructions. The affordable way to add more fun and safety to boating. Available in multiple bezel colors Q41 Anti fog lens. Black face and Black bezel; Orange/White graduations. No illumination. Wiring included with this single pack. Quicksilver Branded, Box Point of Sale Packaged. information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 425

18 DIGITAL DEPTH GAUGE KIT DIGITAL DEPTH/ TEMP GAUGE KIT A05 Digital depth readout 2.5 ft to 200 ft display at speeds of up to 63 MPH. It has backlit lighting for night operation.and incluudes the ability to set shallow water alarm. Easy addition to any boat. Fits in a cutout for standard 2 in.(51 mm) gauge. Order face plate, bezel and transducer seperately ( Standard bezel and face dial liste below) TRANSDUCER - IN HULL/TRANSOM DEPTH ONLY A08 Transducer that can be mounted In Hull or Transom Depth only Can be used on most boats mounted to the outside of the transom TRANSDUCER - THRU HULL A11 Digital depth readout dusplays 2.5 to 200 ft deep at speeds up to 63 MPH. Includes ability to set shallow water alarm warning. Also displays air or water temp. Display is backlit for night operation. Easy addition to any boat. Fits in a cutout for standard 2 in.(51 mm) gauge. *Order bezel and transducer seperately. (ProView bezel and special face dial listed below.) BEZEL 52 MM Bezel Gold 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only BEZEL 52 MM A09 Transducer for Depth and Temp gauge that has 2 3/4 inch threads for deep mounting can be used in most sterndrive and inboard applications TRANSDUCER - IN HULL/TRANSOM Bezel Chrome 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only A10 Transducer that mounts In hull or Transom that works with Depth / Temp gauge A11 Can be used on most boats mounted to the outside of the transom Quicksilver Precision Parts & Accessories Guide

19 BEZEL 52 MM VDO FAMILY GAUGES VDO PRIMARY STATION INSTRUMENTATION - STANDARD Bezel Flat Black 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only BEZEL 52 MM Bezel White 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only FACE PLATE A 1 Pre wired panel with 21 pin Deutsch connector for 1.7L stern drives/inboards. Basic Instrument Set. VDO tach, warning lights for low oil pressure, charge indicator, glow plug activation, coolant temp., water in fuel. Includes key switch, stop button, instrument lights/audio warning test switch. Fits MCM.MIE D1.7L DTI diesels. VDO PRIMARY STATION INSTRUMENTATION - OPTIONAL A 1 Optional pre wired panel with 21 pin Deutsch connector for 1.7L stern drives. Full Instrument Set. VDO tach, oil pressure, water temperature, battery meter & trim guage. Also warning lights for low oil pressure, charge indicator, glow plug activation, coolant temp., water in fuel. Includes key switch, stop button, instrument lights/audio warning test switch. Fits MCM D1.7L DTI diesels Face Plate Color Black 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only FACE PLATE MARINER - UNIQUE GAUGES Gauges unique to Mariner outboards that will not be found in the standard gauge families. Large gauge fits 3 3/8 in.(86 mm) hole in dash. MODULE ASSEMBLY Face Plate Color White 2 inch (52 MM) Bezel is a twist fit that has a round shape. Used on Depth Sounders only 17461A 2 Tachometer Module Assembly. Adapts all Quicksilver tachometers, except A 1, for use with Japanese built outboards. information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 427

20 SPEEDOMETER PICKUPS WATER TEMPERATURE SENDER SPEEDOMETER PICKUP 77409A 1 Pickup and mounting screws only SPEEDOMETER PICKUP TUBING 13536A14 A four wire temperature sender for use on V 6 outboard product. Furnished standard on engine powerhead, the fiche card specific to the application should be used to verify correct use. WATER TEMPERATURE SENDER ft.(16.15 m) tubing roll of 1500 ft.(457.5 m) tubing (1/8" 27 NPT threads) Fits outboard applications. TEMPERATURE SENDER KIT WATER TEMPERATURE SENDERS Water temperature senders used for operation of a temperature gauge. WATER TEMPERATURE SENDER 12415A 2 Allows adding a temperature sender to outboards equipped with a factory built coastal flush. Includes a temperature sender, fittings, cable ties and instruction sheet. This kit provides for the use of a coastal flush and a temperature sender at the same time. Fits Mercury/Mariner hp. (1993 and newer) 2 cycle outboards. Primarily designed for adding to a Saltwater model which comes with the coastal flush as standard equipment A13 A two wire temperature sender for use on V 6 outboard product. Furnished standard on engine powerhead, the fiche card specific to the application should be used to verify correct use. ADAPTOR HARNESS A55 Allows water temperature gauge hook up to the 225 EFI FourStroke outboard Quicksilver Precision Parts & Accessories Guide

21 WATER TEMPERATURE SENDER COOLANT TEMPERATURE SENDER Used for temperature gauge Fits MCM 3.7L engines ENGINE WATER TEMPERATURE SENDER T Used for temperature gauge Fits MCM/MIE EFI models For dual station installations, used for temperature gauge Fits MCM/MIE engines WATER TEMPERATURE SENDER OIL PRESSURE SENDERS OIL PRESSURE SENSOR KIT T 3/8 in. x 18 NPT threads, used for temperature gauge Fits MCM/MIE engines WATER TEMPERATURE SENDER A01 Required when SmartCraft is installed on 3.0L MPI & Vazer engines. Replaces the original analog oil pressure sensor with a digital sensor. Fits MCM 3.0L MPI & Vazer engines OIL PRESSURE SENDER 97258A 1 1/2 in. x 14 NPT threads, used for temperature gauge Fits MCM/MIE engines T For use with 80 psi electric oil pressure gauge information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 429

22 OIL PRESSURE SENDER KIT POWER TRIM SENDERS POWER TRIM SENDER A 1 Includes sender and harness used with oil pressure gauges and 21 ft.(6.4 m) of wire. Fits Mercury/Mariner 25/30/40/45/50/60 (4 stroke). OIL PRESSURE SENDER A03 Includes trim limit switch also. Fits MC I, R, MR, Alpha One, Gen II, Bravo drives. POWER TRIM SENDER T For use with 120 psi electric oil pressure gauge Used with MCM D1.7L DTI diesel engines OIL PRESSURE SENDER A 6 For dual station applications. Fits MCM I/R/MR/Alpha One/Gen II/Bravo One & Two drives. POWER TRIM SENDER A PSI oil gauge sender with a 90 degree elbow and installation instruction sheet. F225 4 stroke engine A 8 For dual station applications. Fits MCM TR & TRS drives. POWER TRIM SENDER CONVERSION KIT A 3 Converts single station sender to a dual station sender. Fits MCM Alpha One/Gen II/Bravo One & Two drives Quicksilver Precision Parts & Accessories Guide

23 POWER TRIM SENDER POWER TRIM SENDER A 6 Port mounted. Fits all outboard 3 ram trim applications except the Digital OptiMax. See application chart for specific engine models. POWER TRIM SENDER Starboard mounted. Fits the Mercury/Mariner V 225 FourStroke outboard engine. POWER TRIM SENDER A 2 Starboard mounted. Fits various in line outboards. See application chart for specific engine models. POWER TRIM SENDER A01 Starboard Mounted. Required for digital gauge applications. Fits Mercury/Mariner 75/90/115hp (1.5L) OptiMax outboard engines, Model Year 2004 and newer. TRIM SENSOR CONVERTER KIT 8M This kit will allow you to convert the signal from the digital sensor to an analog signal. It will allow you to drive an analog gauge for trim only without changing the sensor to an analog sensor. This kit will connect directly to the harness inside the emgine cowl. 150 HP 4 Stroke engine only A12 Port mounted. Contains 6 32 threaded mounting screws. Fits various in line outboards. See application chart for specific engine models. POWER TRIM SENDER A 1 Port mounted. Fits Mercury/Mariner V 6 Digital OptiMax outboards (USA 0G and Newer). information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 431

24 POWER TRIM SENDER CHART Mercury/Mariner Trim Senders Model Brand Model Notes Year Range Country Serial # Range Port Mount Trim Sender Stbd. Mount Trim Sender 25 FourStroke Mercury/Mariner Carb Models only USA 0G and up A12 N/A 25 FourStroke Mercury/Mariner Carb Models only BEL 0P and up A12 N/A 25 FourStroke Mercury/Mariner EFI w/ 6-32 threads JPN 0R and up A12 N/A 25 FourStroke Mercury/Mariner EFI w/ 6-32 threads BEL 0P and up A12 N/A 30 Mercury/Mariner 2 cylinder USA 0G and up A12 N/A 30 Mercury/Mariner 2 cylinder BEL and up A12 N/A 30 FourStroke Mercury/Mariner 3 cylinder Non-BigFoot Models USA 0G B N/A A 2 30 FourStroke Mercury/Mariner 3 cylinder Non-BigFoot models BEL 0P P N/A A 2 30 FourStroke Mercury/Mariner EFI w/ 6-32 threads JPN 0R and up A12 N/A 30 FourStroke Mercury/Mariner EFI w/ 6-32 threads BEL 0P and up A12 N/A 30 JET Mercury/Mariner 4 cylinder USA 0C G N/A N/A 30 JET Mercury/Mariner 3 cylinder USA 0G T A12 N/A 30 JET Mercury/Mariner 3 cylinder BEL 0P P A12 N/A 35 Mercury/Mariner 2 cylinder USA C N/A N/A 35 Mercury/Mariner 2 cylinder BEL and up N/A N/A 35 Mercury/Mariner 2 cylinder CAN and up N/A N/A 40 Mercury/Mariner 4 cylinder with integral trim USA 0C D N/A N/A 40 Mercury/Mariner 4 cylinder with integral trim BEL N/A N/A 40 Mercury/Mariner 4 cylinder USA 0D G N/A A 2 40 Mercury/Mariner 4 cylinder BEL N/A A 2 40 Mercury/Mariner 2 cylinder USA 0G and up A12 N/A 40 Mercury/Mariner 2 cylinder BEL and up A12 N/A 40 Mercury/Mariner 3 cylinder, 59 CID, Long shaft only / USA 0G and up A12 N/A 40 Mercury/Mariner 3 cylinder, 59 CID, Long shaft only / BEL and up A12 N/A 40 FourStroke Mercury/Mariner 3 cylinder Non-BigFoot models USA 0G and up N/A A 2 40 FourStroke Mercury/Mariner 3 cylinder Non-BigFoot models BEL 0P and up N/A A 2 40 FourStroke Mercury/Mariner 3 cylinder BigFoot models USA 0G T N/A A 2 40 FourStroke Mercury/Mariner 3 cylinder BigFoot models BEL 0P P N/A A 2 40 FourStroke Mercury/Mariner 4 cylinder Italy/Bodensee USA 0G G A12 N/A 40 FourStroke Mercury/Mariner 4 cylinder Italy/Bodensee BEL 0P P N/A A 2 40 FourStroke Mercury/Mariner 4 cylinder, 996 cc., BigFoot models USA 0T B N/A A 2 40 FourStroke Mercury/Mariner 4 cylinder, 996 cc., BigFoot models BEL 0P and up N/A A 2 40 FourStroke Mercury/Mariner 4 cylinder, 996 cc., BigFoot models CHN 1C and up N/A A 2 40 JET Mercury/Mariner USA 0T and up A12 N/A 40 JET Mercury/Mariner BEL 0P and up A12 N/A 45 Mercury/Mariner 4 cylinder USA D N/A N/A 45 Mercury/Mariner 4 cylinder AUS and up N/A N/A 45 Mercury/Mariner 4 cylinder BEL N/A N/A 45 Mercury/Mariner 4 cylinder CAN and up N/A N/A 45 FourStroke Mercury/Mariner 4 cylinder Italy/Bodensee USA 0G G A12 N/A 45 FourStroke Mercury/Mariner 4 cylinder Italy/Bodensee BEL 0P P N/A A 2 45 JET Mercury/Mariner 3 cylinder, 51.8 CID USA 0D G N/A A 2 45 JET Mercury/Mariner 3 cylinder, 59 CID USA 0G T A12 N/A 45 JET Mercury/Mariner 3 cylinder, 59 CID BEL 0P P A12 N/A 50 Mercury/Mariner 4 cylinder with external trim USA N/A N/A 50 Mercury/Mariner 4 cylinder with external trim AUS and up N/A N/A 50 Mercury/Mariner 4 cylinder with external trim BEL N/A N/A 50 Mercury/Mariner 4 cylinder with external trim CAN N/A N/A 50 Mercury/Mariner 3 cylinder with external trim USA D N/A N/A Quicksilver Precision Parts & Accessories Guide

25 Model Brand Model Notes Year Range Country Serial # Range Port Mount Trim Sender Stbd. Mount Trim Sender 50 Mercury/Mariner 3 cylinder with external trim BEL N/A N/A 50 Mercury/Mariner 3 cylinder with external trim CAN and up N/A N/A 50 Mercury/Mariner 3 cylinder, 51.8 CID USA 0D G N/A A 2 50 Mercury/Mariner 3 cylinder, 51.8 CID BEL N/A A 2 50 Mercury/Mariner 3 cylinder, 59 CID USA 0G and up A12 N/A 50 Mercury/Mariner 3 cylinder, 59 CID BEL and up A12 N/A 50 FourStroke Mercury/Mariner 4 cylinder Non-BigFoot models USA 0G G A12 N/A 50 FourStroke Mercury/Mariner 4 cylinder Non-BigFoot models USA 0G T N/A A 2 50 FourStroke Mercury/Mariner 4 cylinder BigFoot models USA 0G T N/A A 2 50 FourStroke Mercury/Mariner 4 cylinder, 996 cc., all models USA 0T B N/A A 2 50 FourStroke Mercury/Mariner 4 cylinder, 996 cc., all models BEL 0P and up N/A A 2 50 FourStroke Mercury/Mariner 4 cylinder, 996 cc., BigFoot models CHN 1C and up N/A A 2 55 Mercury/Mariner 3 cylinder, 51.8 CID USA 0D G N/A N/A 55 Mercury/Mariner 3 cylinder, 51.8 CID BEL N/A N/A 55 Mercury/Mariner 3 cylinder, 59 CID USA 0G and up N/A A 2 55 Mercury/Mariner 3 cylinder, 59 CID BEL and up N/A A 2 60 Mercury/Mariner 3 cylinder with external trim USA B N/A N/A 60 Mercury/Mariner 3 cylinder with external trim BEL N/A N/A 60 Mercury/Mariner 3 cylinder with external trim CAN A N/A N/A 60 Mercury/Mariner 3 cylinder with internal trim USA 0C D N/A N/A 60 Mercury/Mariner 3 cylinder with internal trim BEL N/A N/A 60 Mercury/Mariner 3 cylinder with internal trim CAN 0A and up N/A N/A 60 Mercury/Mariner 3 cylinder, all models USA 0D and up N/A A 2 60 Mercury/Mariner 3 cylinder, all models BEL and up N/A A 2 60 FourStroke Mercury/Mariner 4 cylinder, 996 cc., all models USA 0T B N/A A 2 60 FourStroke Mercury/Mariner 4 cylinder, 996 cc., all models BEL 0P and up N/A A 2 60 FourStroke Mercury/Mariner 4 cylinder, 996 cc., BigFoot models CHN 1C and up N/A A 2 70 Mercury/Mariner 3 cylinder with 3-ram trim USA 0A C A 6 N/A 70 Mercury/Mariner 3 cylinder with 3-ram trim BEL A 6 N/A 70 Mercury/Mariner 3 cylinder with single ram trim USA 0A C N/A A 2 70 Mercury/Mariner 3 cylinder with single ram trim BEL N/A A 2 75 Mercury/Mariner 4 cylinder with 3-ram trim USA B A 6 N/A 75 Mercury/Mariner 4 cylinder with 3-ram trim BEL A 6 N/A 75 Mercury/Mariner 4 cylinder with 3-ram trim CAN A A 6 N/A 75 Mercury/Mariner 4 cylinder with single ram trim USA B N/A A 2 75 Mercury/Mariner 4 cylinder with single ram trim BEL N/A A 2 75 Mercury/Mariner 4 cylinder with single ram trim CAN A N/A A 2 75 Mercury/Mariner 3 cylinder with 3-ram trim /2 USA 0A G A 6 N/A 75 Mercury/Mariner 3 cylinder with 3-ram trim /2 BEL A 6 N/A 75 Mercury/Mariner 3 cylinder with single ram trim USA 0A and up N/A A 2 75 Mercury/Mariner 3 cylinder with single ram trim BEL and up N/A A 2 75 Optimax Mercury/Mariner 1.5L DFI, non-digital sender USA 0T and up N/A A 2(1) 75 Optimax Mercury/Mariner 1.5L DFI, digital sender USA 0T and up N/A A01(2) 75 FourStroke Mercury/Mariner USA 0G B N/A A 2 75 FourStroke mercury/mariner B and up N/A A 2 80 Mercury/Mariner 4 cylinder with external trim USA N/A N/A 80 Mercury/Mariner 4 cylinder with external trim AUS and up N/A N/A 80 Mercury/Mariner 4 cylinder with external trim BEL N/A N/A 80 Mercury/Mariner 4 cylinder with external trim CAN N/A N/A 80 Mercury/Mariner 3 cylinder with 3-ram trim USA 0A C A 6 N/A 80 Mercury/Mariner 3 cylinder with 3-ram trim BEL A 6 N/A 80 Mercury/Mariner 3 cylinder with single ram trim USA 0A C N/A A 2 80 Mercury/Mariner 3 cylinder with single ram trim BEL N/A A 2 information, please contact your local Mercury, Mariner, MerCruiser or Quicksilver Office. 433

26 Model Brand Model Notes Year Range Country Serial # Range Port Mount Trim Sender Stbd. Mount Trim Sender 90 Mercury/Mariner 6 cylinder with external trim USA A N/A N/A 90 Mercury/Mariner 6 cylinder with external trim AUS and up N/A N/A 90 Mercury/Mariner 6 cylinder with external trim CAN and up N/A N/A 90 Mercury/Mariner 3 cylinder with 3-ram trim /2 USA 0A G A 6 N/A 90 Mercury/Mariner 3 cylinder with 3-ram trim /2 BEL A 6 N/A 90 Mercury/Mariner 3 cylinder with single ram trim USA 0A and up N/A A 2 90 Mercury/Mariner 3 cylinder with single ram trim BEL and up N/A A 2 90 Optimax Mercury/Mariner 1.5L DFI, non-digital sender USA 0T and up N/A A 2(1) 90 Optimax Mercury/Mariner 1.5L DFI, digital sender USA 0T and up N/A A01(2) 90 FourStroke Mercury/Mariner USA 0G B N/A A 2 90 FourStroke Mercury/Mariner USA 1B and up N/A A Mercury/Mariner 4 cylinder with 3-ram trim USA 0B D A A Mercury/Mariner 4 cylinder with 3-ram trim BEL A A Mercury/Mariner 4 cylinder with single ram trim USA 0B and up N/A A Mercury/Mariner 4 cylinder with single ram trim BEL and up N/A A Mercury/Mariner 6 cylinder with external trim USA C N/A N/A 115 Mercury/Mariner 6 cylinder with external trim AUS and up N/A N/A 115 Mercury/Mariner 6 cylinder with external trim CAN and up N/A N/A 115 Mercury/Mariner 4 cylinder with 3-ram trim USA 0B D A A Mercury/Mariner 4 cylinder with 3-ram trim BEL A A Mercury/Mariner 4 cylinder with single ram trim USA 0B and up N/A A Mercury/Mariner 4 cylinder with single ram trim BEL and up N/A A Optimax Mercury/Mariner 2.5L DFI, non-digital sender USA 0G T A 6(1) N/A 115 Optimax Mercury/Mariner 2.5L DFI, digital sender USA 0G T A 1(2) N/A 115 Optimax Mercury/Mariner 1.5L DFI, non-digital sender USA 0T and up N/A A 2(1) 115 Optimax Mercury/Mariner 1.5L DFI, digital sender USA 0T and up N/A A01(2) 115 FourStroke Mercury/Mariner EFI USA 0T B N/A A FourStroke Mercury/Mariner EFI USA 1B and up N/A A Mercury/Mariner 4 cylinder USA 0D and up N/A A Mercury/Mariner 4 cylinder BEL and up N/A A FourStroke Mercury/Mariner USA 0T and up N/A (1) V-6 Mercury/Mariner Non-digital sender & 3-ram trim. All USA All - All A 6(1) N/A V-6 Mercury/Mariner Digital sender & 3-ram trim USA 0G and up A 1(2) N/A (1) For use with analog gauges. (2) For use with 555 controller and SmartCraft gauges or monitors Quicksilver Precision Parts & Accessories Guide