ENGLISH

Size: px
Start display at page:

Download "ENGLISH www.bandg.com www.simrad-yachting.com www.lowrance.com"

Transcription

1 StructureScan HD Transom mount Installation Guide ENGLISH

2 Warning: It is your sole responsibility to install and use the instrument and transducer(s) in a manner that will not cause accidents, personal injury or property damage. Always observe safe boating practices. The choice, location, and installation of transducers and other components of the system are critical to the performance of the system as intended. If in doubt, consult your Navman dealer. To reduce the risk of misusing or misinterpreting this instrument, you must read and understand all aspects of this Installation and Operation Manual. We also recommend that you practice all operations using the built-in simulator before using this instrument on the water. Sonar performance: The accuracy of the sonar depth display can be affected by many factors, including the type and location of the transducer and water conditions. Never use this instrument to gauge depth or other conditions for swimming or diving. The choice, location, and installation of transducers and other components of the system are critical to the performance of the system as intended. If in doubt, consult your Navman dealer. To reduce the risk of misusing or misinterpreting this instrument, you must read and understand all aspects of this Installation and Operation Manual. We also recommend that you practice all operations using the built-in simulator before using this instrument on the water.

3 1 Installation preparation Accessories If you received this manual with a StructureScan accessory, you will notice that some information in the document does not apply to the accessory. This manual has installation instructions for your accessory, and accessory pack content tables on the back cover. Contents Your StructureScan box is packed with the StructureScan HD module, a Power cable, fuse and fuse holder, StructureScan transducer, mounting bracket, 15 foot (4.5m) ethernet cable and a hardware kit. The transducer has a 20 foot (6m) cable attached. Hardware Mounting Kit (included) Transom mount screws (2) Bracket assembly bolts (2) Bracket assembly washers (4) Bracket assembly nuts (2) Transducer attachment screws (6) Transducer attachment lock nuts (6) StructureScan HD mounting screws (4) Closed end crimp connector (1) Zip ties (2) Drill Drill bits Required tools and supplies (not included) Phillips (slotted-head screwdriver) Marine grade above-or-below waterline sealant StructureScan HD Installation preparation 3

4 Mounting options The StructureScan transducer can be mounted on the transom, jackplate, step or directly to your boat s hull. When mounting it directly to the hull, you must purchase a highquality, marine grade above- or below-waterline sealant/adhesive compound. Use the following table to determine which mounting option is best suited to your boat/installation preferences. ¼¼ Note: When mounting the StructureScan transducer, make sure there is nothing around the mounting location that could interfere with StructureScan transducer sonar beams. Jackplate mount Step mount Transom mount 4 StructureScan HD Installation preparation

5 StructureScan HD transducer mounting options Transom mount (Page 8) Keeps transducer in the water when the boat is on plane, allowing you to track bottom at high speeds Transducer angle can be adjusted so it is parallel with the water Transducer more likely to collide with obstructions in the water and adds drag to the boat Jackplate mount (Page 9) Step mount (Page 10) Direct mount/step (Page 11) Trolling motor mount (sold separately) Transducer is not in the water when boat is on plane; protects transducer and prevents drag from transducer Transducer angle can be adjusted so it is parallel with the water Allows you to mount transducer without drilling holes in your boat Does not track bottom when boat is on plane Transducer is not in the water when boat is on plane; protects transducer and prevents drag from transducer Transducer angle can be adjusted so it is parallel with the water Does not track bottom when boat is on plane Transducer is not in the water when boat is on plane Protects transducer and prevents drag from transducer Transducer angle can not be adjusted so it is parallel with the water Does not track bottom when boat is on plane Visit StructureScan HD Installation preparation 5

6 2 Installation Bracket and transducer assembly The StructureScan bracket comes with four washers, two bolts and two nuts. If you plan to mount the StructureScan transducer directly to the step (Step Mount) or on the trolling motor, you do not need to assemble the bracket. OR 6 StructureScan HD Installation

7 Transducer angle After mounting the StructureScan transducer, make sure the transducer is adjusted so it will be parallel with the waterline when moving at trolling speed. Downscan Overlay The StructureScan transducer should be installed within approximately 1 foot of the broadband sounder transducer to get optimum performance from the Downscan Overlay feature. It is recommended you turn off Downscan Overlay when using your trolling motor as the sonar source, unless the StructureScan transducer and broadband sounder transducer both are installed on the trolling motor. Downscan overlay performance could be degraded if the StructureScan transducer is too far away from the broadband sounder transducer installed on the trolling motor. < 0.3m (1ft) StructureScan HD Installation 7

8 Transom mount The StructureScan transducer can be mounted just like a skimmer transducer, where it is in the water when you are on plane or can be mounted so it is only in the water, when you are moving at trolling speed. Transom Mount Supplies (not included) 1/8 Drill bit (Transom mount pilot holes) Marine grade above- or belowwaterline sealant Transom Mount (Aluminum Hull) Supplies (not included) Marine grade above- or below- M4 Machine Screws waterline sealant Starboard (prevents corrosion between bracket and aluminum hull) To Mount StructureScan transducer on Transom: 1. Choose a transducer location and then route the transducer cable to the location where the StructureScan module will be installed. 2. Place the transducer bracket against the transom and then align the bottom of the transducer with the bottom of boat. Use a pencil to mark the pilot holes through the slots in the transducer bracket. 3. Drill the pilot holes into the boat s transom. 4. Apply a high-grade above- or below-waterline sealant to the pilot holes. 5. Align the bracket slots over the pilot holes and fasten the bracket to the transom using your drill and the supplied screws. 6. To make adjustments to transducer position, loosen the screws and slide bracket up or down. 7. Connect the transducer cable to the StructureScan module sonar port. 8 StructureScan HD Installation

9 Jackplate Mount The StructureScan transducer can be mounted inside or outside of the jackplate by drilling through the jackplate and then running bolts though the hinge hole in the side of the bracket into the jackplate. Jackplate Mount Supplies (not included) M6 or 1/4 Drill bit (Jackplate 1/4 (M6) jackplate mount bolts Mount) pilot holes Warning: Before installing the StructureScan HD transducer on the jackplate, lower the jackplate to its lowest setting to make sure there is enough clearance between the jack plate/engine and the transducer. Lack of clearance could damage the transducer when the engine is all the way down. To Mount StructureScan on Jackplate: 1. Choose a transducer location on the inside or outside of the jackplate. 2. Adjust the jackplate up and down to make sure the transducer will not obstruct jackplate movement. 3. Make sure nothing blocks the sonar beam on either side of the transducer. 4. Route the transducer cable to the location where the module will be installed. 5. Move the transducer bracket into the desired position and use a pencil to mark the holes through the hinge hole and hole in the side of the bracket. 6. Using a M6 or equivalent drill bit, drill the holes into the jackplate. 7. Slide the bracket inside the jackplate and align the bracket holes with holes you drilled in the jackplate. 8. Slide M6 bolts with washers into each hole on the side of jackplate. 9. Guide the bolts through the StructureScan bracket holes. 10. Place a washer over the end of the bolts and tighten the nuts. 11. Connect the transducer cable to the StructureScan module sonar port. Jackplate StructureScan bracket mounted inside the jackplate. The bracket can also be installed on the outside of the jackplate. StructureScan HD Installation 9

10 Step Mount Mounting the StructureScan transducer under the step not only protects the transducer from hitting objects in the water, but does not cause any drag on your boat when it is on plane. 1/8 Drill bit (Transom mount pilot holes) Step Mount Supplies (not included) Marine grade above- or belowwaterline sealant To use Step Mount: 1. Choose a transducer location. 2. Route the transducer cable to the location where the StructureScan module will be installed. 3. Move the transducer bracket into the desired position and then use a pencil to mark the pilot holes through the slots in the bracket. 4. Drill the pilot holes. 5. Apply a high-grade above- or below-waterline sealant to the pilot holes. 6. Align the bracket slots over the pilot holes and fasten the bracket to the transom using your drill and the supplied screws. 7. To make adjustments to transducer position, loosen the screws and slide bracket up or down. 8. Connect the transducer cable to the StructureScan module sonar port. Step 10 StructureScan HD Installation

11 Direct/Step Mount (No Bracket) When using the direct mount installation shown below, you MUST turn on the Flip Left/Right feature. Refer to your Operation manual for more information.. Direct Step Mount Supplies (not included) 3/32 Drill bit (Direct/Step mount pilot holes) Marine grade above- or belowwaterline sealant To use Direct Mount: 1. Make sure the boat s step is the same length or longer than the StructureScan transducer. 2. After selecting a mounting location, route the transducer cable to the location where the StructureScan module will be installed. 3. Hold the transducer in the desired position and then use a pencil to mark pilot holes through the mounting holes on the transducer. 4. Drill the pilot holes. 5. Apply a high-grade above- or below-waterline sealant to the pilot holes. 6. Align the transducer mounting holes over the pilot holes and mount the transducer to the step using self-tapping metal screws (not supplied). Do NOT overtighten the screws; otherwise you could strip out the fiberglass pilot holes or crack the mounting holes on the StructureScan transducer. 7. Connect the transducer cable to the StructureScan module and then turn on the Flip Left/Right feature on your display unit. Do not install under boat hull! Direct mount (without bracket) ¼¼ NOTE: When using a Direct Step Mount, you must turn on the Flip Left/Right feature in your display unit to ensure what is shown on the left/right side on your display, corresponds with what is on the left/right side of your boat. StructureScan HD Installation 11

12 2.1 (55.5mm) 10.8 (274.3mm) 2.8 (72.7mm) 10.1 (257.3mm) Parts and accessories StructureScan Module ( ) StructureScan module Closed-end crimp connector mounting screws (4) Fuse and fuse holder StructureScan Skimmer Bracket ( ) Transom mount screws (2) Bracket assembly nuts (2) Transducer attachment Transducer attachment lock nuts (6) screws (6) Bracket assembly bolts (2) Zip ties (2) Bracket assembly washers (4) StructureScan Skimmer Transducer ( ) Transom mount screws (2) Bracket assembly nuts (2) Transducer attachment Transducer attachment lock nuts (6) screws (6) Bracket assembly bolts (2) Zip ties (2) Bracket assembly washers (4) 12 StructureScan HD Installation

13 Power Requirement Voltage Input Transmit Power StructureScan Specifications 12 Volts 10V - 17V WRMS: 500W WPK: 4000W Current Drain Max:.75A Typical:.60A Inrush: 4.7A pk Fuse Type External: 3A Fast Acting Automotive Blade Transducer Cable 20 feet (6m) Target Separation 1.5 (38.1mm) Transducer Frequency 455kHz Communication Ethernet Shared devices supported 3 StructureScan module (1.8lbs) Weight Transducer (1.9lbs) Transducer with bracket (2.55lbs) Max Range Max Speed Mark objects Optimum speed Sidescan Specifications 455kHz (500ft 250 per side) 35 mph (56 kmh) 15 mph (24 kmh) 10 mph (16 kmh) or less Max Depth Max Speed Mark objects Optimum speed Downscan Specifications 300 ft (455kHz) 55 mph (88 kmh) 35 mph (56 kmh) 10 mph (16 kmh) or less 13

14 StructureScan LED Guide Indicator LED Status Definition Transducer LED Transducer LED Transducer LED Off Green/ stays on Green/ flashing Transducer not connected or cable/transducer is broken Transducer detected/locked on to bottom Transducer detected/not locked on to bottom Power LED Off No power or not switched on Power LED Red/stays on Product in booting process Power LED Green/stays on Product has power/operating Power LED Power LED Ethernet LED Ethernet LED Red/Green/ slow flashing Red/Green fast flashing Off Yellow/ Flashing Product in factory mode; ethernet communication working Product in factory mode; no ethernet communication (cable unplugged or bad cable) No ethernet communication (cable unplugged, bad cable or remote unit not powered) Ethernet communication is working (link/active light) 14

15 StructureScan not displayed No Data Data washed out/ same color Left/right data swapped on screen No Source is displayed StructureScan Troubleshooting Tips Make sure StructureScan HD is powered Check unit software; must have at least version 2.5 Make sure yellow wire is connected to switched power source Check fuse Check range or turn on auto range Turn down contrast; try different palettes Toggle the Flip Left/Right feature Make sure HDS unit and StructureScan are powered and connected to ethernet network Make sure all switches are powered Check link/active light to see which units are not communicating 15

16 * *

StructureScan HD Transducer Installation manual

StructureScan HD Transducer Installation manual StructureScan HD Transducer Installation manual ENGLISH www.simrad-yachting.com www.lowrance.com 1 Preface Warning: It is your sole responsibility to install and use the instrument and transducer(s) in

More information

StructureScan Installation

StructureScan Installation StructureScan Installation Contents Your StructureScan box is packed with the LSS-1 black box, a Power cable, StructureScan transducer, mounting bracket, 15 foot (4.5m) ethernet cable and a hardware kit.

More information

TotalScan Transducer Installation manual

TotalScan Transducer Installation manual TotalScan Transducer Installation manual ENGLISH www.simrad-yachting.com www.lowrance.com 1 Preface Warning: It is your sole responsibility to install and use the instrument and transducer(s) in a manner

More information

StructureScan HD Module. Installation Guide ENGLISH. www.bandg.com www.simrad-yachting.com www.lowrance.com

StructureScan HD Module. Installation Guide ENGLISH. www.bandg.com www.simrad-yachting.com www.lowrance.com StructureScan HD Module Installation Guide ENGLISH www.bandg.com www.simrad-yachting.com www.lowrance.com Disclaimer As Navico is continuously improving this product, we retain the right to make changes

More information

Manual. Simrad StructureScan LSS-1 Sonar Module. English

Manual. Simrad StructureScan LSS-1 Sonar Module. English Manual Simrad StructureScan LSS-1 Sonar Module English www.simrad-yachting.com A brand by Navico - Leader in Marine Electronics Disclaimer As Navico is continuously improving this product, we retain the

More information

Traditional Sonar and DSI Sonar Installation

Traditional Sonar and DSI Sonar Installation Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and installing the unit on

More information

Transducer Installation

Transducer Installation Transducer Installation This document covers the installation of all 83/200kHz, 50/200kHz and Downscan transducers using transom and shoot-thru hull installation methods, where applicable. This manual

More information

INSTALLATION MANUAL. Installation Instructions

INSTALLATION MANUAL. Installation Instructions INSTALLATION MANUAL Power-Pole Signature Series Shallow Water Anchor Installation Instructions CAUTION: Read this instruction manual carefully. Become familiar with the controls and know how to operate

More information

HOOK-3x DSI. Operation manual. lowrance.com ENGLISH. HOOK-3x DSI

HOOK-3x DSI. Operation manual. lowrance.com ENGLISH. HOOK-3x DSI HOOK-3x DSI Operation manual ENGLISH HOOK-3x DSI lowrance.com Copyright 2015 Navico All rights reserved. Lowrance and Navico are registered trademarks of Navico. Navico may find it necessary to change

More information

StructureScan 3D. User Guide ENGLISH. www.simrad-yachting.com www.lowrance.com

StructureScan 3D. User Guide ENGLISH. www.simrad-yachting.com www.lowrance.com StructureScan 3D User Guide ENGLISH www.simrad-yachting.com www.lowrance.com Contents 5 About StructureScan 3D 7 Basic operation 7 Selecting the StructureScan source 7 Zooming 8 Stopping/pausing sonar

More information

TABLE OF CONTENTS. Section 1: GENERAL INFORMATION How Sonar Works Transducer Exchange. Section 2: INSTALLATION Parts Supplied Transducer Installation

TABLE OF CONTENTS. Section 1: GENERAL INFORMATION How Sonar Works Transducer Exchange. Section 2: INSTALLATION Parts Supplied Transducer Installation Thank you for choosing Humminbird, America s #1 name in depthsounders. Humminbird has built its reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment. Your Humminbird

More information

360 Imaging. Installation Guide 532050-1_B

360 Imaging. Installation Guide 532050-1_B 360 Imaging Installation Guide 532050-1_B Thank You! Thank you for choosing Humminbird, the #1 name in Fishfinders. Humminbird has built its reputation by designing and manufacturing top-quality, thoroughly

More information

GSD 22 Sounder Module. installation instructions

GSD 22 Sounder Module. installation instructions GSD 22 Sounder Module installation instructions Copyright 2006 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151 st Street, Olathe, Kansas 66062, USA Tel. (913) 397.8200 or (800)

More information

User Manual. Instructions for installing the Sure Stitch on the Next Generation Quilting Frame. Parts Included:

User Manual. Instructions for installing the Sure Stitch on the Next Generation Quilting Frame. Parts Included: User Manual Instructions for installing the Sure Stitch on the Next Generation Quilting Frame. Parts Included: 1: Display Console 1: Control Box 2: Encoder (Wires attached) (Not Shown) 1: 5v Power Supply

More information

GreenWay Solar LED Path and Trail Lighting System. Installation and Owner s Manual

GreenWay Solar LED Path and Trail Lighting System. Installation and Owner s Manual GreenWay Solar LED Path and Trail Lighting System Installation and Owner s Manual Important Notes and Warnings This installation and instruction manual provides installation, operation, and maintenance

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment

More information

INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II

INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS

More information

Ethernet Networking Installation & Operations Manual Humminbird ETHERNET

Ethernet Networking Installation & Operations Manual Humminbird ETHERNET Ethernet Networking Installation & Operations Manual 531906-2EN_A GPS Unit 1 Humminbird ETHERNET Unit 2 Thank You! Thank you for choosing Humminbird, the #1 name in marine electronics. Humminbird has built

More information

SIMRAD SD10 Sailboat Drive

SIMRAD SD10 Sailboat Drive INSTALLATION MANUAL SIMRAD SD10 Sailboat Drive 20222683/A English Simrad SD10 Sailboat Drive About this document Rev. A First issue 2007 Navico AS. All rights reserved. No part of this work covered by

More information

MCR1900 Media Converter 19-Slot Chassis

MCR1900 Media Converter 19-Slot Chassis MCR1900 Media Converter 19-Slot Chassis Installation Guide Part #5500304-11 Copyright Statement This document must not be reproduced in any way whatsoever, either printed or electronically, without the

More information

Wiper Motor Marinco 2.5. Installation Instructions

Wiper Motor Marinco 2.5. Installation Instructions Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet

More information

Oceanscience Cable Chimp II Cableway ROV System User Guide and Warranty

Oceanscience Cable Chimp II Cableway ROV System User Guide and Warranty Oceanscience Cable Chimp II Cableway ROV System User Guide and Warranty Page 1 Table of Contents Introduction Page 3 Overview Page 3 Setup and Operation Page 5 Remote Control Page 6 Power Management Page

More information

Home Signal Distribution Kit for Cable TV Plus SIRIUS

Home Signal Distribution Kit for Cable TV Plus SIRIUS Home Signal Distribution Kit for Cable TV Plus SIRIUS For Use With a Single SIRIUS Radio Installation Manual Thank you for purchasing the Home Signal Distribution Kit for Cable TV Plus SIRIUS The Home

More information

SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #6100 INPOOL LADDER 42" TO 54" ASSEMBLY AND INSTRUCTION MANUAL

SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #6100 INPOOL LADDER 42 TO 54 ASSEMBLY AND INSTRUCTION MANUAL SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER MODEL #6100 INPOOL LADDER 42" TO 54" ASSEMBLY AND INSTRUCTION MANUAL The Anti-Entrapment Barrier is included in this ladder for the U.S. and

More information

BBWX1 Satellite Weather Receiver. Installation and Maintenance Guide

BBWX1 Satellite Weather Receiver. Installation and Maintenance Guide BBWX1 Satellite Weather Receiver Installation and Maintenance Guide Rev FUSA 15JUL2007 Table of Contents Safety Precautions 3 Disclaimer. 3 Contents of Package. 4 Tools Required..4 Installation General

More information

StructureMap. HDS Gen 2 Addendum. Viewing StructureMap data

StructureMap. HDS Gen 2 Addendum. Viewing StructureMap data StructureMap HDS Gen 2 Addendum StructureMap is a tool that allows you to overlay SideScan sonar returns on top of the chart, giving you a birds-eye view of underwater structure below and beside your boat.

More information

Home Signal Distribution Kit for Satellite TV Plus SIRIUS

Home Signal Distribution Kit for Satellite TV Plus SIRIUS SR-101C SIRIUS/DBS Signal Combiner System SR-2261 Combiner-Outdoor Made in China DBS IN SIRIUS IN SR-101C SIRIUS/DBS Signal Combiner System SR-2251 Splitter-Indoor Made in China DC IN DBS OUT SIRIUS OUT

More information

ELECTRONICS G H I J K L M

ELECTRONICS G H I J K L M ELECTRONICS TM LASER INSTALLATION INSTRUCTIONS PARTS KIT Parts Kit includes the following: A- (1) Universal Mounting Bracket A B- (1) Red L.E.D. Laser Alert Light C- (1) Piezo Beeper w/ O Ring Tape D-

More information

AZEK Rail Install Guide

AZEK Rail Install Guide TRIM MOULDING DECK PORCH RAIL PAVERS AZEK Rail Install Guide Installing AZEK Rail with CableRail by Feeney... 1 Installing CableRail by Feeney for AZEK Rail... 7 Installing AZEK Rail Stairs with CableRail

More information

Table of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.

Table of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing. www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing

More information

Cisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2440NV-R)

Cisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2440NV-R) Cisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2440NV-R) This document outlines the specifications for the Cisco Aironet 2.4-GHz MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2440NV-R)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls

More information

5X, Mark 5X, Mark 5X Pro & Elite 4X

5X, Mark 5X, Mark 5X Pro & Elite 4X Elite 5X, Mark 5X, Mark 5X Pro & Elite 4X Installation & Operation manual Operation manual Copyright 2011 Navico All rights reserved. Lowrance and Navico are registered trademarks of Navico. Navico may

More information

430 Power/Electronics Replacement

430 Power/Electronics Replacement Replacing the main board WARNING Before proceeding, turn off the main power switch and unplug the power cord. Caution Make sure you are properly grounded with an ESD strap before continuing. The main printed

More information

JANUS INTERNATIONAL CORPORATION INSTALLATION INSTRUCTIONS Pantheon Mini Operator

JANUS INTERNATIONAL CORPORATION INSTALLATION INSTRUCTIONS Pantheon Mini Operator JANUS INTERNATIONAL CORPORATION INSTALLATION INSTRUCTIONS Pantheon Mini Operator The Janus Pantheon mini operator does not typically require the provision of any additional site requirements other than

More information

Installation Instructions Avalanche XUV Cap IMPORTANT! IMPORTANT!

Installation Instructions Avalanche XUV Cap IMPORTANT! IMPORTANT! Installation Instructions Avalanche XUV Cap IMPORTANT! Read all instructions carefully before commencing any work. Always wear safety equipment. Some installation steps will require two or more installers.

More information

INSTALLATION MANUAL. Contents JAPANESE ENGLISH GERMAN FRENCH ITALIAN SPANISH. To the installing technician: CEILING BRACKET

INSTALLATION MANUAL. Contents JAPANESE ENGLISH GERMAN FRENCH ITALIAN SPANISH. To the installing technician: CEILING BRACKET Be sure to read this installation manual thoroughly prior to installation. If installation methods or non-standard parts not specified in this installation manual are used, accidents or injury may result.

More information

SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE

SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop

More information

PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129

PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: The information included in this Splendide Repair Manual may change without notice. Please see our web site www.splendide.com/service/docs.html for updates,

More information

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE

More information

Installation Instructions

Installation Instructions 520 Installation Instructions Thank you very much for purchasing PIAA product. Please read this entire manual before installation and use of this product. For Installers Please give this Installation Manual

More information

Andersen Electric Window Opener for Andersen Awning and Roof Windows

Andersen Electric Window Opener for Andersen Awning and Roof Windows W A Electric Window Opener Electric Window Opener for Awning and Roof Windows Congratulations! You have just purchased one of the many fine products. For ease of installation and continued enjoyment of

More information

RadianceRail Installation Guide

RadianceRail Installation Guide RadianceRail Installation Guide Installing RadianceRail with CableRail by Feeney... 2 Installing CableRail by Feeney for RadianceRail... 7 Installing RadianceRail Stairs with CableRail by Feeney... 10

More information

LST-3800. In-Dash Digital Sonar Gauge. Installation & Operation Instructions

LST-3800. In-Dash Digital Sonar Gauge. Installation & Operation Instructions Pub. 988-0064-351 LST-3800 In-Dash Digital Sonar Gauge Installation & Operation Instructions The LST-3800 is a depth and temperature gauge that comes with a 200 khz transducer, features deep and shallow

More information

UPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video

UPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video UPLIFT Height Adjustable Standing Desk (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE - - ALSO - - Watch our assembly video http://bit.ly/9ywwh! CAUTION MAKE SURE NO OBSTACLES ARE IN THE DESK S PATH AND ALL

More information

Control Box Wiring For PRSstandard Tool

Control Box Wiring For PRSstandard Tool 888-680-4466 ShopBotTools.com Control Box Wiring For PRSstandard Tool Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Introduction:...5 Installation:...5

More information

X-4 Pro. Fish-Finding Sonar. Installation and Operation Instructions

X-4 Pro. Fish-Finding Sonar. Installation and Operation Instructions X-4 Pro Fish-Finding Sonar Installation and Operation Instructions Copyright 2010 Navico All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed for

More information

ReachFree ID Installation Instructions For Portal TI, Sentinel and C-Start. Unitec www.startwithunitec.com

ReachFree ID Installation Instructions For Portal TI, Sentinel and C-Start. Unitec www.startwithunitec.com ReachFree ID Installation Instructions For Portal TI, Sentinel and C-Start Unitec www.startwithunitec.com Proprietary Information and Materials of Unitec, Inc. Such proprietary information and materials

More information

MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER

MODEL# SLA001-3 SLIDE & LOCK A-FRAME POOL LADDER MODEL# SLA001-3 "SLIDE & LOCK" A-FRAME POOL LADDER IMPORTANT INSTRUCTIONS: : Read all instructions carefully & completely to become familiar with parts, assembly, safety and proper use of this product.

More information

tidesmarine Smart Seal Temperature Alarm System Generation II Installation Instructions Starboard side cable

tidesmarine Smart Seal Temperature Alarm System Generation II Installation Instructions Starboard side cable tidesmarine Smart Seal Temperature Alarm System Generation II Installation Instructions Starboard side cable Port side cable (with black cable tie attached) Power cable Preparing for Installation 1 Overall

More information

CONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation

CONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER

More information

PRS X-axis E-chain installation: For tools with a 12 Z-Axis

PRS X-axis E-chain installation: For tools with a 12 Z-Axis PRS X-axis Energy Chain (Echain) Installation Page -1- PRS X-axis E-chain installation: For tools with a 12 Z-Axis This kit is compatible with PRS Shopbots that have an X-axis cutting area of 96 to 144.

More information

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES PART NUMBER: 250-9612 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD FOCUS SE & S MODELS (AT/MT) FORD TRANSIT ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES

More information

Time needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.

Time needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk. DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Application Outboards Faria 5 Gauge Set* Publication No. Description Part Number Honda Code PII53606A White faced, flat lens 06300-ZW5-010ZB 6315410 Issue Date Black faced, flat

More information

SCREENLOGIC INTERFACE WIRELESS CONNECTION KIT

SCREENLOGIC INTERFACE WIRELESS CONNECTION KIT SCREENLOGIC INTERFACE WIRELESS CONNECTION KIT FOR INTELLITOUCH AND EASYTOUCH CONTROL SYSTEMS INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Technical

More information

Installation & User Manual Radio Remote rev1.0.3

Installation & User Manual Radio Remote rev1.0.3 EN Installation & User Manual Radio Remote rev1.0.3 RC-20E RC-21E RC-22E RC-23E SLEIPNER MOTOR AS P.O. Box 519 N-1612 Fredrikstad Norway Tel: +47 69 30 00 60 Fax: +47 69 30 00 70 www.side-power.com sidepower@sleipner.no

More information

12 Volt 30 Amp Digital Solar Charge Controller

12 Volt 30 Amp Digital Solar Charge Controller 12 Volt 30 Amp Digital Solar Charge Controller User s Manual WARNING Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions

More information

4.3-inch Back-Up Camera

4.3-inch Back-Up Camera TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION

More information

ScreenLogic Wireless Connection Kit. Installation Guide. pool/spa control system

ScreenLogic Wireless Connection Kit. Installation Guide. pool/spa control system pool/spa control system ScreenLogic Wireless Connection Kit Installation Guide P/N 520663 - Rev B 8 Technical Support Contact Technical Support at: Sanford, North Carolina (8 A.M. to 5 P.M.) Phone: (800)

More information

Part Name/Description Part Number Quantity. Power Cable 4000950-5 1

Part Name/Description Part Number Quantity. Power Cable 4000950-5 1 Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Power Cable 4000950-5 1 Raven Harness Adapter Kit 4100525 1 Installation Instructions

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 24393 ACCORD (DX, LX) SYSTEM 2-AND 4-DOOR Issue Date AUG 2002 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel

More information

DANGER DANGER. General Information. Safety Is Your Responsibility. Ordering Parts. Contact Information

DANGER DANGER. General Information. Safety Is Your Responsibility. Ordering Parts. Contact Information Safety Safety Is Your Responsibility DANGER To avoid personal injury or death, carefully read and understand all instructions pertaining to the Anthony Liftgates product. Do not attempt to install, operate,

More information

PowerFlex 700H and 700S AC Drives Frame 11 Main Fan Capacitor Replacement Kit

PowerFlex 700H and 700S AC Drives Frame 11 Main Fan Capacitor Replacement Kit Installation Instructions PowerFlex 700H and 700S AC Drives Frame 11 Main Fan Capacitor Replacement Kit ATTENTION: The sheet metal cover and mounting screws on the ASIC Board located on the power structure

More information

Installation Instructions For Slider Casement Air Conditioners

Installation Instructions For Slider Casement Air Conditioners Installation Instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT

More information

ASSEMBLY MANUAL SE-4S35

ASSEMBLY MANUAL SE-4S35 Automatic drive ASSEBLY ANUAL SE-4S35 AI-4S35 SG-4R35 Battery box otor unit Inter-4 hub CONTENTS WARNING 1 INSTALLATION CONITIONS Battery box Speed sensor Cable lengths and diameters otor unit Recommended

More information

SCHWINTEK IN-WALL SLIDEOUT TROUBLESHOOTING AND COMPONENT REPLACEMENT

SCHWINTEK IN-WALL SLIDEOUT TROUBLESHOOTING AND COMPONENT REPLACEMENT Troubleshooting Error Codes During operation when an error occurs, the board will use the LEDs to indicate where the problem exists. For motor specific faults, the green LED will blink once for Motor 1,

More information

Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family

Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family Part of the Kiva Lighting Family Custom Lighting and Fans Since 1992 1312 12th St NW Albuquerque,

More information

Zebra RW 420 Mobile Battery Eliminator Kits

Zebra RW 420 Mobile Battery Eliminator Kits Zebra Technologies Corporation 475 Half Day Road, Suite 500 Lincolnshire, IL 60069 USA Zebra RW 420 Mobile Battery Eliminator Kits Installation Instructions September, 2010 RW 420 Mobile Battery Eliminator

More information

Not required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided)

Not required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided) ELECTRIC FUEL PUMPS P/N 12-801-1, 712-801-1, 12-802-1, 712-802-1, 12-815-1, & 712-815-1 FUEL PRESSURE REGULATORS P/N 12-803, 12-501, 12-804, 12-500, & 15812NOS Installation Instructions THESE INSTRUCTIONS

More information

DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual

DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR Installation and Operation Manual 1 ENGLISH Safety Instructions 2 Features 2-3 Specifications 3 Installation 4-5 Wiring Diagrams 6-7 Warranty 8

More information

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES

RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES HYUNDAI ACCENT 2010- /ELANTRA 2012- / KIA RIO 2012- PART NUMBER: 250-9628 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: (AT/MT) VEHICLES RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION

More information

AMF112 (6904-002010 <00>) 13mm (1/2 in.)

AMF112 (6904-002010 <00>) 13mm (1/2 in.) AMF112 () Concrete Wood 13mm (1/2 in.) 5.5mm (7/32 in.) 10mm (3/8 in.) Sanus Systems 2221 Hwy 36 West Saint Paul, MN 55113 USA Customer Service Americas: 800-359-5520 651-484-7988 info@sanus.com Europe,

More information

Triple Threat 3-in-1 Game Table 3 IN 1 GAME TABLE

Triple Threat 3-in-1 Game Table 3 IN 1 GAME TABLE NG0M Triple Threat 3-in- Game Table 3 IN GAME TABLE Thank 3 in Y Game Table Thank you for your purchase of our product. We work around the clock and around the globe to ensure that our products maintain

More information

Model: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features

Model: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features Model: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features Mirror with built in 4.0 LCD Monitor Low Profile, Slim Design High Resolution TFT LCD Built in Speaker Two video inputs Fully

More information

Step 1. Item 6. Item 1

Step 1. Item 6. Item 1 Voltage Regulators QD3/T350 Motor Replacement Kit Kit Number 57A63675100B Service Information S225-50-35 Contents General..................................... 1 Parts Supplied...............................

More information

POWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents

POWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents -J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English

More information

HOOK-X Series. Operation manual. lowrance.com ENGLISH. HOOK-4x HOOK-5x HOOK-7x

HOOK-X Series. Operation manual. lowrance.com ENGLISH. HOOK-4x HOOK-5x HOOK-7x HOOK-X Series Operation manual ENGLISH HOOK-4x HOOK-5x HOOK-7x lowrance.com Copyright 2016 Navico All rights reserved. Lowrance and Navico are registered trademarks of Navico. Navico may find it necessary

More information

ECM-D70T / ECM-D70T1.5

ECM-D70T / ECM-D70T1.5 Elliptical Ceiling Dual Mount for 37 to 50 Flat Panels INSTALLATION INSTRUCTIONS CREATING POSITIVE CUSTOMER EXPERIENCES 9531-041-001-01 Contents ECM-D70T / ECM-D70T1.5 Installation Tools... 3 Parts List...

More information

Wireless Indoor/ Outdoor Thermometer

Wireless Indoor/ Outdoor Thermometer Wireless Indoor/ Outdoor Thermometer Owner s Manual Please read before using this equipment. ˆ Contents FCC Information... 3 FCC Declaration of Conformity... 5 Preparation... 5 Installing Batteries...

More information

OPL BASIC. Dosing System for Professional Laundry machines. Contents

OPL BASIC. Dosing System for Professional Laundry machines. Contents OPL BASIC Dosing System for Professional Laundry machines Contents 1 Getting Started. Page 2 2 Installation. Page 4 3 Set Up & Operation. Page 8 4 Maintenance & Accessories. Page 10 5 Troubleshooting Page

More information

Owner s Manual Read and keep this manual. Patents World Wide

Owner s Manual Read and keep this manual. Patents World Wide Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2008 All Rights Reserved The following manual is provided to assist

More information

Multi-Pitch Pitching Machine USER MANUAL

Multi-Pitch Pitching Machine USER MANUAL Multi-Pitch Pitching Machine USER MANUAL TABLE OF CONTENTS Thank you for purchasing the Cimarron Multi-Pitch Pitching Machine. The Cimarron Multi-Pitch Pitching Machine is a high performance pitching machine

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual

More information

MEDIUM FLAT PANEL DISPLAY STATIC MOUNT MSR Series

MEDIUM FLAT PANEL DISPLAY STATIC MOUNT MSR Series INSTALLATION INSTRUCTIONS MEDIUM FLAT PANEL DISPLAY STATIC MOUNT The static mount accommodates medium flat panel displays weighing up to 125 lbs (57 kgs). The teardrop holes in the mount allow for quick

More information

Advantium 2 Plus Alarm

Advantium 2 Plus Alarm ADI 9510-B Advantium 2 Plus Alarm INSTALLATION AND OPERATING INSTRUCTIONS Carefully Read These Instructions Before Operating Carefully Read These Controls Corporation of America 1501 Harpers Road Virginia

More information

EP-80R Temp. Electronic Temperature Sensor Installation and Configuration Instructions

EP-80R Temp. Electronic Temperature Sensor Installation and Configuration Instructions Pub. 988-0154-472 EP-80R Temp Electronic Temperature Sensor Installation and Configuration Instructions This document shows how to install an EP-80R temp sensor and how to connect it to a NMEA 2000 network.

More information

BATTERY BOX INSTALLATION WARNING WARNING CAUTION ATTENTION AVERTISSEMENT ADVERTENCIA PRECAUCIÓN SOLBBOX12V CARTON INVENTORY COMPLETED OVERVIEW

BATTERY BOX INSTALLATION WARNING WARNING CAUTION ATTENTION AVERTISSEMENT ADVERTENCIA PRECAUCIÓN SOLBBOX12V CARTON INVENTORY COMPLETED OVERVIEW WARNING CARTON INVENTORY CAUTION with: Charger, Cable 15', Fuses (2), Battery Strap and Strain Relief (2) Model SOLBBOX 12V Battery Not Included AVERTISSEMENT ATTENTION DC Power Adapter 12Vdc to 32Vdc

More information

LIEBERT VNSA Installation Sheet

LIEBERT VNSA Installation Sheet LIEBERT VNSA Installation Sheet Description The Liebert vnsa network switch is designed for connecting multiple Ethernet-ready devices and comes in various models. The unit may have: A Liebert icom display

More information

WINEGARD MOTORIZED SENSAR ANTENNA Models MA1055W & MA1055G MADE IN U.S.A. U.S. Patents D500,496 and 7,358,909 INSTALLATION MANUAL

WINEGARD MOTORIZED SENSAR ANTENNA Models MA1055W & MA1055G MADE IN U.S.A. U.S. Patents D500,496 and 7,358,909 INSTALLATION MANUAL WINEGARD MOTORIZED SENSAR ANTENNA Models MA1055W & MA1055G MADE IN U.S.A. U.S. Patents D500,496 and 7,358,909 INSTALLATION MANUAL CAUTION: This system is not for use with antenna in raised position while

More information

PUSH BUTTON START INSTALLATION MANUAL

PUSH BUTTON START INSTALLATION MANUAL PUSH BUTTON START INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS PRODUCT.

More information

Micrio WS1 Replacement Wind Speed Sensor and WC1 Replacement Wind Compass Sensor for Raymarine ST50 and ST60 Wind Instruments. Rev 4.

Micrio WS1 Replacement Wind Speed Sensor and WC1 Replacement Wind Compass Sensor for Raymarine ST50 and ST60 Wind Instruments. Rev 4. Micrio WS1 Replacement Wind Speed Sensor and WC1 Replacement Wind Compass Sensor for Raymarine ST50 and ST60 Wind Instruments. Rev 4.1 The Micrio WS1 Wind Speed Sensor and WC1 Compass Sensor are direct

More information

Original Assembly Guide

Original Assembly Guide TCT Multipurpose Single Bevel Sliding Compound Mitre Saw Original Assembly Guide Read instructions before assembling this tool. Table of Contents GB Assembly Guide Read instructions before assembling this

More information

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT

More information

STEALTH I DC MANUAL TECH SUPPORT 1-888-588-4506.WEB www.stealth1charging.com BLACK UNIT IS 24/36 ONLY

STEALTH I DC MANUAL TECH SUPPORT 1-888-588-4506.WEB www.stealth1charging.com BLACK UNIT IS 24/36 ONLY STEALTH I DC MANUAL TECH SUPPORT 1-888-588-4506.WEB www.stealth1charging.com BLACK UNIT IS 24/36 ONLY PLEASE READ AND UNDERSTAND YOUR NEW PRODUCT IMPORTANT MESSAGE: Before installing your newly purchased

More information

HEAVY DUTY STAIR LIFT SYSTEM Installation and Service Manual

HEAVY DUTY STAIR LIFT SYSTEM Installation and Service Manual HEAVY DUTY STAIR LIFT SYSTEM Installation and Service Manual WARNING! STRICT ADHERENCE TO THESE INSTALLATION INSTRUCTIONS is required and will promote the safety of those installing this product, as well

More information

Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors

Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...

More information

73 Chevy C10 Ammeter to Volt Gauge Conversion Mark and Michael Olson 2013 Rev 1.0

73 Chevy C10 Ammeter to Volt Gauge Conversion Mark and Michael Olson 2013 Rev 1.0 73 Chevy C10 Ammeter to Volt Conversion Mark and Michael Olson 2013 Rev 1.0 The ammeter in my son s 73 Chevy C10 did not work, so we decided to convert it to a more modern volt gauge. We made a number

More information