WHAT MAKES A GOOD BRAKE DRUM
|
|
|
- Opal Sheila Parrish
- 9 years ago
- Views:
Transcription
1 WHAT MAKES A GOOD BRAKE DRUM There are a number of attributes that differentiate between mediocre and a good brake drum. The following highlights these and what they mean to the end user. 1. A HEAT ABSORPTION DEVICE (HEAT SINK) The braking system in a vehicle converts the vehicle energy of motion into heat energy by means of friction between the brake lining and the brake surface of the brake drum when the vehicle s brakes are applied. a). The surrounding parts, such as brake lining, rim, tire, hub, bearings, and drum absorb heat by conduction and radiation. b). The surrounding air is heated by convection. Radiated heat to surrounding parts is small and heat dissipated by convection to the surrounding air is slow relative to the actual time of braking. For these reasons nearly all the braking energy must be stored in the form of heat in the brake drum. This energy is stored by heating the drum material to a higher temperature than the drum temperature prior to the brake application. A heavier drum will store more energy than a light one will. A heavier drum is stronger and more fade resistant. 2. A CYLINDRICAL BRAKE LINING INTERFACE The brake drum moves past a stationary brake lining. When (if) the brake surface does not move past the lining uniformly, the brake drum has run out. This will overstress the brake drum, linings, and attaching hardware, causing variable heating of the brake drum braking surface which results in heat checking, excessive ware of both the drum and lining, pulsing of the brake, and shortened life of both the drum and lining. Also to keep the drum dimensionally stable under these conditions, it must be a relatively heavy brake drum. A heavy precise brake drum does not reduce the need for linings to fit the drum correctly. If the linings are not contoured to fit properly, the brake will not produce proper breaking torque. Poorly contoured linings cause additional mechanical stress in the drum, shoes and lining, and brake hardware. This additional stress hastens failure and greater wear. Before linings are burnished or seated into the brake drum, they may rub on only a few high spots. These superheat the brake drum braking surface in very small areas and can be seen on the brake dynamometer as fire bands. A light brake application will cause this to occur whereas a snub brake application will force the lining against more of the braking surface of the brake drum thus limiting or even eliminating these types of hot spots. If these hot spots are allowed to continue, martensite hot spots will occur, and in turn drum distortion, and very early cracking can happen. Lining that takes longer to burnish will be more likely to cause hot spotting. Many of the non-asbestos organic linings fall into this category. Since martensite hot spotted brake drums cannot usually be successfully rebored, they usually must be scrapped. 3. HIGH STRENGTH, HEAT, AND WEAR RESISTANT BRAKE DRUM MATERIAL A brake drum must be strong enough to resist the maximum mechanical stress caused by the expanding and selfenergized brake shoes at high temperatures. The brake drum s stiffness or resistance to deflection is derived from the thick shell structure and the stiffness of the gray cast iron. Higher tensile strength gray iron does not change the deflection of the brake drum significantly. Although higher strength iron is more resistance to thermal stress caused by temperature gradients, as a hot brake surface and a cold outside brake drum diameter. The occurring problem here is the cold outside diameter of the brake drum does not want to expand to a bigger diameter, but the hot inside diameter of the brake drum does want to expand. The hot inner surface is caused to compress or compresses plastically so that it fits within the cold outer surface. But as the hot inner surface cools, cracks form because the metal was too compressed to return to its original position thus resulting in hairline surface cracks known as heat checks. 4. HEAVY ROTATING PARTS THAT IF IMBALANCED CAN SIGNIFICANTLY AFFECT THE VEHICLES RIDE The mass of a 16.5" x 7" brake drum is concentrated about 9 inches radially from the hub bearing centerline. Unless the brake drum is balanced, it helps excite vibration in trucks and trailers. That is why it is important to use balanced brake drums on all front and rear applications. Most brake drum balancing is done by welding weights to the outside of the drum, but ArvinMeritor pioneered and patented a technique to balance brake drums without welding on balance weights. This is called Machine to Balance (MTB). The industry typically requires front hub/drum or hub/rotor assemblies balanced to 20-in. oz. maximum and rear hub/drum or hub/rotor assemblies balanced to 50-in. oz. maximum. 5
2 DRIVE AXLE HUBS Dana Spicer J-190S Eaton 17, 34D, D340 Meritor FL-100, RS , RS , RS , RT HUB PART COMMENTS Wheel studs not included J1258 STUD PILOTED - Hub Assemblies without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE STUD LH RH HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION MTB Dual Steel Cast N x Outboard MTB Dual Steel Cast x Outboard MTB Dual Aluminum Cast x Outboard MTB Aluminum, Steel Cast J x Outboard 28
3 DRIVE AXLE HUBS S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast Serrated 3/4"-16 R Stud Piloted Serrated 3/4"-16 L Stud Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".50".50"-13.83".50"-20.98" ".50".50" ".50" " DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast MTB 16.50" x 7.00" 10.31" 8.78" Cast MTB 15.00" x 8.63" 12.20" 8.78" 29
4 DRIVE AXLE HUBS Dana Spicer J-190S Eaton 17, 34D, D340 Meritor "L" Series FL-100, RS , RS , RS , RT HUB PART COMMENTS Wheel studs not included HUB PILOTED - Hub Assembly without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M20 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".50".50" ".50" " 30
5 DRIVE AXLE HUBS Dana Spicer J-190S Eaton 17, 34D, D340 Meritor FL-100, RS , RS , RS , RT HUB PART COMMENTS Wheel studs not included HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH RH STUD PILOTED - Hub and Rotor Assembly HUB PART HAND WHEEL TYPE STUD ROTOR ROTOR OUTSIDE DIAMETER RH LH RH LH
6 DRIVE AXLE HUBS HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast Serrated 3/4"-16 R Stud Piloted Serrated 3/4"-16 L Stud Piloted Serrated M22 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".50".50"-13.83".50"-20.98" ".50".50" ".50" " ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
7 DRIVE AXLE HUBS Eaton 18, 23 26, 38D, 44D, D380, D381, D400 (Tag Axles 25LD, H25LD) Meritor RD , RS , RS , RS , RS , RS , RS , RD , RS , RS , RS , RT , RT , RT , RT , RT , RT , RT , RT , SQ100, SQR100, SSHD (Tag Axles TR, TRD, TT) HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH RH S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63"-11.84".63"-18.97" 33
8 DRIVE AXLE HUBS Dana Spicer J-190S Eaton 17, 34D, D340 Meritor FL-100, RS , RS , RS , RT HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M20 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD NO. OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".50".50"-13.83".50"-20.98" ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART No. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
9 DRIVE AXLE HUBS Dana Spicer J-190S Eaton 17, 34D, D340 Meritor FL-100, RS , RS , RS , RT STUD PILOTED - Hub Assemblies without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH LH HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH RH S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated 3/4"-16 R Stud Piloted Serrated 3/4"-16 L Stud Piloted Serrated M22 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63" ".63" " 35
10 Ford DRIVE AXLE HUBS STUD PILOTED - Hub Assemblies without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE RH RH STUD S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 9/16"-18 R Stud Piloted Serrated 9/16"-18 R Stud Piloted 36
11 DRIVE AXLE HUBS Dana Spicer D135-S, S135-S, S150-S, F155-S, G155-T Navistar 170 Series HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH RH S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD NO. OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".56".56"-12 1".56"-18.90" 37
12 DRIVE AXLE HUBS Dana Spicer J-190S Eaton 17, 34D, D340 Meritor FL-100, RS , RS , RS , RT HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH RH S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD NO. OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63" ".63" " 38
13 DRIVE AXLE HUBS Eaton 18, 23 26, 38D, 44D, D380, D381, D400 (Tag Axles 25LD, H25LD) Meritor RD , RS , RS , RS , RS , RS , RS , RD , RS , RS , RS , RT , RT , RT , RT , RT , RT , RT , RT , SQ100, SQR100, SSHD (Tag Axles TR, TRD, TT) HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR O.D S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63" ".63" " ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
14 GMC 150 DRIVE AXLE HUBS HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M20 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD NO. OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".50".50" ".50" " 40
15 GMC 150 DRIVE AXLE HUBS HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR O.D S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".50".50" ".50" " ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
16 DRIVE AXLE HUBS Dana Spicer J-190S Eaton 17, 34D, D340 Meritor FL-100, RS , RS , RS , RT HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH RH HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".50".50"-13.83".50"-20.98" ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
17 DRIVE AXLE HUBS Eaton 15040P, 15040S, 15040T Meritor F-145, F-245, F-345, RS , RS HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR O.D S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M14 x 2 Hub Piloted Steel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".50".50"-13.83".50"-20.98" ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
18 Dana Model 80 DRIVE AXLE HUBS HUB PART HAND WHEEL TYPE DRUM TYPE LH RH STUD HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR O.D S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M20 x 1.5 Hub Piloted Steel Cast Serrated M20 x 1.5 Hub Piloted Steel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNC
19 Hino DRIVE AXLE HUBS HUB PART HAND WHEEL TYPE DRUM TYPE RH STUD HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR O.D Steel S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M14 x 2 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNC
20 DRIVE AXLE HUBS Eaton 18, 23 26, 38D, 44D, D380, D381, D400 (Tag Axles 25LD, H25LD) Meritor RD , RS , RS , RS , RS , RS , RS , RD , RS , RS , RS , RT , RT , RT , RT , RT , RT , RT , RT , SQ100, SQR100, SSHD (Tag Axles TR, TRD, TT) HUB PART NO. HAND WHEEL TYPE DRUM TYPE NO. STUD NO. NO RH RH H RH RH H1256 STUD PILOTED - Hub and Drum Assemblies HUB PART HAND WHEEL TYPE DRUM TYPE WHEEL STUD DRIVE FLANGE STUD DRUM SIZE DRUM DRUM POSITION MTB LH Aluminum, Steel Cast H x Outboard MTB RH Aluminum, Steel Cast H x Outboard HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION MTB Steel Cast H x Outboard 46
21 DRIVE AXLE HUBS S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 3/4"-16 R Stud Piloted Steel Wheel Cast Serrated 3/4"-16 L Stud Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63"-11.85".63" " DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast MTB 16.50" x 7.00" 10.54" 8.78" Cast MTB 16.50" x 7.00" 10.54" 8.78" 47
22 DRIVE AXLE HUBS Eaton 18, 23 26, 38D, 44D, D380, D381, D400 (Tag Axles 25LD, H25LD) Meritor RD , RS , RS , RS , RS , RS , RS , RD , RS , RS , RS , RT , RT , RT , RT , RT , RT , RT , RT , SQ100, SQR100, SSHD (Tag Axles TR, TRD, TT) HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH RH RH HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR O.D
23 DRIVE AXLE HUBS S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD PART OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63"-11.85".63" " ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNF UNF
24 DRIVE AXLE HUBS Eaton 18, 23 26, 38D, 44D, D380, D381, D400 (Tag Axles 25LD, H25LD) Meritor RD , RS , RS , RS , RS , RS , RS , RD , RS , RS , RS , RT , RT , RT , RT , RT , RT , RT , RT , SQ100, SQR100, SSHD (Tag Axles TR, TRD, TT) HUB PART NO. HAND WHEEL TYPE DRUM TYPE STUD RH RH RH HUB PILOTED - Hub and Rotor Assembly HUB PART NO. WHEEL TYPE STUD ROTOR ROTOR O.D
25 DRIVE AXLE HUBS S USED WITH HUB IN ASSEMBLIES PART THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD PART OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63"-11.85".63" " ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNF
26 DRIVE AXLE HUBS Eaton 18, 23 26, 38D, 44D, D380, D381, D400 (Tag Axles 25LD, H25LD) Meritor RD , RS , RS , RS , RS , RS , RS , RD , RS , RS , RS , RT , RT , RT , RT , RT , RT , RT , RT , SQ100, SQR100, SSHD (Tag Axles TR, TRD, TT) HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH RH HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR O.D T S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63"-11.85".63" " ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNF
27 DRIVE AXLE HUBS FOR AXLE MODELS: Meritor MC26000, HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH X RH X-1612 HUB PILOTED - Hub and Rotor Assembly HUB PART WHEEL TYPE STUD ROTOR ROTOR O.D X X S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH 4-X ".56".56"-12.84".56"-18.91" ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA M16x
28 XpresswayPlus.ArvinMeritor.com Don't forget about using XpresswayPlus for: Ordering parts online Order status Reference Library Price and availability The Company Store Invoice Lookup Literature Parts Catalog Dealer/Distributor locator Online or phone numbers for Customer Service, Information Services, Marketing, Catalog, and esupport XpresswayPlus is easy to use, can reduce phone calls, and save you valuable time. WHAT YOU NEED: ACCOUNT CHANGE AFTERMARKET & PRODUCTION ASSEMBLIES APPLICATION INFORMATION BILL-OF-LADING BILL-OF-MATERIAL BULLETINS CONTACT NAMES & S FIELD SUPPORT REPRESENTATIVES INVOICE (VIEW & PRINT) NEWSLETTER ORDER DETAILS ORDER HISTORY FILE ORDER MERCHANDISE ORDER SUBMIT ORDER SUBMIT - STOCK UPLOAD (MULTIPLE LINES) PART DETAILS PART IMAGES PART COMPARISON PARTS BOOKS PASSWORD CHANGE PRICE (LIST) PRICE (NET) & AVAILABILITY PRODUCT BROCHURES PRODUCT UPDATES PROOF-OF-DELIVERY REQUEST-FOR-QUOTATION (FOR MERITOR BRAND) SALES LITERATURE SEND QUESTIONS, COMMENTS, ISSUES SHIPPER TECH TIPS TRACKING WARRANTY INFORMATION WHERE-USED INFORMATION WHERE TO LOOK: CUSTOMER SERVICE CATALOG CATALOG ORDER STATUS CATALOG REFERENCE LIBRARY CUSTOMER SERVICE CUSTOMER SERVICE ORDER STATUS REFERENCE LIBRARY ORDER STATUS ORDER STATUS COMPANY STORE CREATE NEW ORDER CREATE NEW ORDER CATALOG CATALOG CATALOG REFERENCE LIBRARY CUSTOMER SERVICE CATALOG PRICE & AVAILABILITY REFERENCE LIBRARY REFERENCE LIBRARY ORDER STATUS PRICE REQUEST REFERENCE LIBRARY CONTACT US ORDER STATUS REFERENCE LIBRARY ORDER STATUS REFERENCE LIBRARY CATALOG 54
29 Meritor DRIVE AXLE HUBS HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH X RH X-1612 S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast Serrated M22 x 1.5 Hub Piloted STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD NO. OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH 4-X ".56".56"-12.84".56"-18.91" 55
30 DRIVE AXLE HUBS Eaton 18, 23 26, 38D, 44D, D380, D381, D400 (Tag Axles 25LD, H25LD) Meritor RD , RS , RS , RS , RS , RS , RS , RD , RS , RS , RS , RT , RT , RT , RT , RT , RT , RT , RT , SQ100, SQR100, SSHD (Tag Axles TR, TRD, TT) HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH H RH H RH H RH RH S1293 HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION MTB Steel Cast H x Outboard MTB Aluminum Cast x Outboard MTB Aluminum Cast H x Outboard MTB Aluminum, Steel Cast x Outboard MTB Aluminum Cast H x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast 56
31 DRIVE AXLE HUBS STUDS USED WITH HUB IN ASSEMBLIES HUB END NUT END STUD NO. OVERALL LENGTH BODY DIAMETER THREAD SIZE THREAD LENGTH THREAD SIZE THREAD LENGTH ".63".63"-11.85".63" " ".63".63"-11.86".63" " DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast MTB 16.50" x 7.00" 10.54" 8.78" Cast MTB 16.50" x 7.00" 10.59" 8.78" 57
32 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 STUD PILOTED - Hub Assemblies without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE RH LH RH L LH L1260 STUD PILOTED - Hub and Drum Assemblies HUB PART HAND WHEEL TYPE DRUM TYPE DRUM SIZE DRUM DRUM POSITION MTB RH Steel Cast x Outboard MTB LH Steel Cast x Outboard MTB LH Steel Cast L x Outboard MTB RH Steel Cast L x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 1-1/8"-16 R Stud Piloted Steel Cast Serrated 1-1/8"-16 L Stud Piloted Steel Cast Serrated 1-1/8"-16 R Stud Piloted Aluminum Cast Serrated 1-1/8"-16 R Stud Piloted Aluminum Cast DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast MTB 15.00" x 4.00" 8.85" 8.78" 58
33 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE DRUM SIZE DRUM DRUM POSITION Steel Cast x Outboard Steel Cast x Outboard Aluminum Cast x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum Wheel X Serrated M22 x 1.5 Hub Piloted Steel Cast DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast Weld-to-Balance 16.50" x 5.00" 9.16" 11.25" Cast Balanced 16.50" x 6.00" 9.75" 11.25" 59
34 FRONT AXLE HUBS Meritor FC-931, FD-931, FD-933, FD-961 Westport F5W-0900 HUB PART COMMENTS Wheel studs not included HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M20 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
35 GMC FRONT AXLE HUBS HUB PART COMMENTS Wheel studs not included
36 Hino FRONT AXLE HUBS HUB PART COMMENTS Wheel studs not included
37 GMC FRONT AXLE HUBS HUB PART COMMENTS Wheel studs not included
38 GMC FRONT AXLE HUBS HUB PART COMMENTS Wheel studs not included
39 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 STUD PILOTED - Hub Assemblies without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE RH LH RH 20-X LH 20-X-2552 HUB PART WHEEL TYPE DRUM TYPE S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 3/4"-16 R Stud Piloted Steel Wheel Cast Serrated 3/4"-16 L Stud Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Serrated M22 x 1.5 Hub Piloted Steel Cast 20-X-2551 Serrated 3/4"-16 R Stud Piloted 20-X-2552 Serrated 3/4"-16 L Stud Piloted 65
40 FRONT AXLE HUBS FOR AXLE MODELS: Dana Spicer I-160, I-180, I-200, I-220 Meritor FG-942, FL-931, FL-941, FL-943, FL-951 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNF
41 FRONT AXLE HUBS FOR AXLE MODELS: Dana Spicer I-160, I-180, I-200, I-220 Eaton EFA-18F3, EFA-20T2, EFA-22T2/T5, EFA-24T2/T5 Meritor FG-942, FL-931, FL-941, FL-943, FL-951 STUD PILOTED - Hub Assemblies without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE RH LH RH S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 1-1/8"-16 R Stud Piloted Aluminum Cast Serrated 1-1/8"-16 R Stud Piloted Aluminum Cast Serrated 7/8"-14 R Stud Piloted Steel Cast 67
42 Meritor FC-941 FRONT AXLE HUBS HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Serrated M22 x 1.5 Hub Piloted Steel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
43 Dana, ITE FRONT AXLE HUBS HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Serrated M22 x 1.5 Hub Piloted Steel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
44 Dana I-75, I-80 Meritor FC-931, FC-941 Navistar 02ADB, 02101, 02103, FRONT AXLE HUBS STUD PILOTED - Hub Assemblies without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE RH LH HUB PART WHEEL TYPE DRUM TYPE STUD PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE NO. ROTOR ROTOR O.D HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE NO. ROTOR ROTOR O.D
45 FRONT AXLE HUBS S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Serrated M22 x 1.5 Hub Piloted Steel Cast Serrated 3/4"-16 R Stud Piloted Serrated 3/4"-16 L Stud Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
46 Meritor FC-941 FRONT AXLE HUBS HUB PART WHEEL TYPE DRUM TYPE K M1261 HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE DRUM SIZE DRUM DRUM POSITION MTB Steel Cast M x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel X30 DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast MTB 15.00" x 5.00" 10.08" 8.78" 72
47 Meritor FC-941 FRONT AXLE HUBS HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
48 FRONT AXLE HUBS FOR AXLE MODELS: Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 HUB PART WHEEL TYPE DRUM TYPE L L1260 HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE DRUM SIZE DRUM DRUM POSITION MTB Steel Cast L x Outboard MTB Steel Cast L x Outboard MTB Steel Cast L x Outboard MTB Steel Cast L x Outboard MTB Aluminum, Steel Cast x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel X30 DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast MTB 15.00" x 4.00" 8.97" 8.78" Cast MTB 16.50" x 6.00" 9.52" 8.78" Cast MTB 16.50" x 5.00" 9.63" 8.78" Cast MTB 16.50" x 6.00" 9.81" 8.78" 74
49 Meritor FC-941 FRONT AXLE HUBS HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M20 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
50 Meritor FC-941 FRONT AXLE HUBS HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Cast Serrated M22 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
51 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M20 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
52 Hino FRONT AXLE HUBS HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M14 x 2 Hub Piloted Serrated M14 x 2 Hub Piloted Steel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNC
53 Hino FRONT AXLE HUBS HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M20 x 1.5 Hub Piloted Steel Cast Serrated M20 x 1.5 Hub Piloted Steel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNC
54 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER L S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNF
55 FRONT AXLE HUBS FOR AXLE MODELS: Dana Spicer I-160, I-180, I-200, I-220 Eaton EFA-18F3, EFA-20T2, EFA-22T2/T5, EFA-24T2/T5 Meritor FG-942, FL-931, FL-941, FL-943, FL-951 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum Wheel X Serrated M22 x 1.5 Hub Piloted Steel Cast Serrated M22 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNF
56 FRONT AXLE HUBS FOR AXLE MODELS: Dana Spicer I-160, I-180, I-200, I-220 Eaton EFA-18F3, EFA-20T2, EFA-22T2/T5, EFA-24T2/T5 Meritor FG-942, FL-931, FL-941, FL-943, FL-951 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE DRUM SIZE DRUM DRUM POSITION MTB Aluminum, Steel Cast x Outboard MTB Aluminum, Steel Cast x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum Wheel X Serrated M22 x 1.5 Hub Piloted Steel Wheel X30 DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast MTB 16.50" x 6.00" 9.83" 11.71" 82
57 Ford 7000 Early Design FRONT AXLE HUBS HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 3/4"-16 L Stud Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
58 Ford 7000 FRONT AXLE HUBS HUB PART WHEEL TYPE DRUM TYPE S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M14 x 1.5 Hub Piloted 84
59 FRONT AXLE HUBS FOR AXLE MODELS: Dana Spicer I-160, I-180, I-200, I-220 Eaton EFA-18F3, EFA-20T2, EFA-22T2/T5, EFA-24T2/T5 Meritor FG-942, FL-931, FL-941, FL-943, FL-951 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA M16x
60 FRONT AXLE HUBS FOR AXLE MODELS: Dana Spicer I-160, I-180, I-200, I-220 Eaton EFA-18F3, EFA-20T2, EFA-22T2/T5, EFA-24T2/T5 Meritor FG-942, FL-931, FL-941, FL-943, FL-951 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA UNF
61 Navistar FRONT AXLE HUBS HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M14 x 1.5 Hub Piloted ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
62 FRONT AXLE HUBS FOR AXLE MODELS: Dana Spicer I-160, I-180, I-200, I-220 Eaton EFA-18F3, EFA-20T2, EFA-22T2/T5, EFA-24T2/T5 Meritor FG-942, FL-931, FL-941, FL-943, FL-951 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE DRUM SIZE DRUM DRUM POSITION MTB Steel, Disc Cast x Outboard MTB Aluminum Cast x Outboard MTB Aluminum, Disc Cast x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Aluminum Wheel X Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast MTB 16.50" x 6.00" 9.88" 8.78" 88
63 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 STUD PILOTED Hub Assemblies without Drum or Rotor HUB PART HAND WHEEL TYPE DRUM TYPE LH L1260 S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 1-1/8"-16 L Stud Piloted Steel Cast 89
64 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 HUB PART WHEEL TYPE DRUM TYPE L L1260 S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast 90
65 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER L S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA M16x
66 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 HUB PART COMMENTS Wheel studs not included HUB PART WHEEL TYPE DRUM TYPE S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Cast 92
67 FRONT AXLE HUBS Dana Spicer I-100, I-120, I-140, W15 Eaton EFA-12F3, EFA-12F4, EFA-13F4 Meritor FF-931, FF-941, FF-942, FF-943, FF-944, FF-961, FG-931, FG-900, FG-941, FG-943 Westport F3W-1200, F3W-1400, F6W-1200, F6W-1400 HUB PART WHEEL TYPE DRUM TYPE HUB PILOTED - Hub and Rotor Assemblies HUB PART WHEEL TYPE ROTOR ROTOR OUTSIDE DIAMETER S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Cast ROTORS USED WITH HUB IN ASSEMBLIES BOLT HOLES ROTOR PART NO. OUTSIDE DIA. OVERALL DEPTH BOLT CIRCLE DIA. DIAMETER PILOT DIA
68 TRAILER HUBS FOR AXLE MODELS: Dana Spicer D-21, K-21 Eaton C, C2, CB, CD, CD2, HC, HCE, E, ED, EH, 20L, 22L, 22R, 230C Ingersoll A19H, A19S, DC19H Meritor RL, TK, TL, TKLD, TKL Standard Forge A-19H, A-19S HUB PART COMMENTS Wheel studs not included HUB PILOTED - Hub Assemblies without Drum HUB PART WHEEL TYPE DRUM TYPE STUD HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION Steel Cast x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast Non-Balanced 16.50" x 7.00" 10.59" 11.25" 94
69 TRAILER HUBS HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION Steel Cast x Outboard STUDS USED WITH HUB IN ASSEMBLIES STUD NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast Non-Balanced 16.50" x 7.00" 10.59" 11.25" 2 Includes 10 flanged cap nuts. 95
70 TRAILER HUBS FOR AXLE MODELS: Dana Spicer Eaton 225P, 230P, P22 Fruehauf Pro-Par Hendrickson HP Ingersoll A24H, A24S, F24 Meritor TP HUB PART COMMENTS Wheel studs not included STUD PILOTED - Hub Assemblies without Drum HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH Aluminum, Steel Cast LH Aluminum, Steel Cast RH Aluminum, Steel Cast LH Aluminum, Steel Cast HUB PILOTED - Hub Assemblies without Drum HUB PART WHEEL TYPE DRUM TYPE STUD Steel Cast Steel Cast Aluminum Cast, X Aluminum Cast, X STUD PILOTED - Hub and Drum Assemblies HUB PART HAND WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION RH Aluminum, Steel Cast x Outboard LH Aluminum, Steel Cast x Outboard 96
71 TRAILER HUBS HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION Steel Cast x Outboard Aluminum Cast x Outboard Steel Cast x Outboard Steel Cast x Outboard Aluminum Cast x Outboard STUDS USED WITH HUB IN ASSEMBLIES STUD NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 3/4"-16 R Stud Piloted Steel Wheel Cast Serrated 3/4"-16 L Stud Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER Cast Non-Balanced 16.50" x 7.00" 10.54" 8.78" Cast Non-Balanced 16.50" x 7.00" 10.59" 8.78" 97
72 LITE WEIGHT TP TRAILER HUBS Dana Spicer Eaton 225P, 230P, P22 Fruehauf Pro-Par Hendrickson HP Ingersoll A24H, A24S, F24 Meritor TP HUB PART COMMENTS Wheel studs not included HUB PILOTED - Hub Assemblies without Drum HUB PART WHEEL TYPE DRUM TYPE STUD Steel Cast Steel Cast Aluminum Cast STUD PILOTED - Hub and Drum Assemblies HUB PART HAND WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION RH Aluminum, Steel Cast x Outboard LH Aluminum, Steel Cast x Outboard 98
73 LITE WEIGHT TP TRAILER HUBS HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION Steel Cast x Outboard Steel Cast x Outboard Steel Cast x Outboard X30 Steel X x Outboard Steel Cast x Outboard Aluminum Cast x Outboard Aluminum Cast x Outboard Steel Cast x Outboard Steel Cast x Outboard Aluminum Cast x Outboard X30 Steel X x Outboard X30 Aluminum X x Outboard X30 Steel X x Outboard X30 Aluminum X x Outboard MTB Steel Cast x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 3/4"-16 R Stud Piloted Steel Wheel Cast Serrated 3/4"-16 L Stud Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel X Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER X " x 7.00" 10.38" 8.78" Cast Non-Balanced 16.50" x 7.00" 10.54" 8.78" Cast Non-Balanced 16.50" x 7.00" 10.59" 8.78" Cast MTB 16.50" x 8.63" 11.25" 8.78" 99
74 Meritor TL TRAILER HUBS HUB PILOTED - Hub Assemblies without Drum HUB PART WHEEL TYPE DRUM TYPE STUD S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast 100
75 LITE WEIGHT TN TRAILER HUBS Dana Spicer Eaton 23L, 23R, D22, J, JE, JH, K22 Dexter D200K, D2225K Hendrickson HN Ingersoll A22H, A22S, A22T, DC22H, F22 K-B KBS, KBW Meritor RN, RQ, TKN, TN, TQ, TQC, TQD Std Forge A22H, A22S, A22T Westport F3W-1600, F3W-1800, F3W-1800D, F3W-2000, F3W-2000D HUB PART COMMENTS Wheel studs not included STUD PILOTED - Hub Assemblies without Drum HUB PART HAND WHEEL TYPE DRUM TYPE STUD RH Aluminum, Steel Cast RH Aluminum, Steel Cast LH Aluminum, Steel Cast LH Aluminum, Steel Cast RH LH RH LH RH LH RH LH
76 LITE WEIGHT TN TRAILER HUBS HUB PILOTED - Hub Assemblies without Drum HUB PART WHEEL TYPE DRUM TYPE STUD Steel Cast Steel Cast Aluminum, Steel Cast Aluminum, Steel Cast STUD PILOTED - Hub and Drum Assemblies HUB PART HAND WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION RH Aluminum, Steel Cast x Outboard LH Aluminum, Steel Cast x Outboard RH Aluminum, Steel Cast x Outboard LH Aluminum, Steel Cast x Outboard X30 RH Steel X x Outboard X30 LH Steel X x Outboard HUB PILOTED - Hub and Drum Assemblies HUB PART WHEEL TYPE DRUM TYPE STUD DRUM SIZE DRUM DRUM POSITION Steel Cast x Outboard Steel Cast x Outboard X30 Aluminum X x Outboard X30 Aluminum X x Outboard Steel Cast x Outboard Aluminum Cast x Outboard Steel Cast x Outboard Aluminum Cast x Outboard Aluminum Cast x Outboard Aluminum Cast x Outboard X30 Steel X x Outboard X30 Steel X x Outboard S USED WITH HUB IN ASSEMBLIES NO. THREAD TYPE SIZE STYLE WHEEL TYPE USE WITH DRUM TYPE Serrated 3/4"-16 R Stud Piloted Steel Wheel Cast Serrated 3/4"-16 L Stud Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel Cast Serrated M22 x 1.5 Hub Piloted Steel Wheel X Serrated M22 x 1.5 Hub Piloted Aluminum Wheel Cast Serrated M22 x 1.5 Hub Piloted Aluminum, Steel Cast Serrated 3/4"-16 R Stud Piloted Steel Wheel X Serrated 3/4"-16 L Stud Piloted Steel Wheel X30 DRUMS USED WITH HUB IN ASSEMBLIES DRUM NO. DRUM TYPE BRAKE SIZE OVERALL DEPTH PILOT DIAMETER X " x 7.00" 10.38" 8.78" Cast Non-Balanced 16.50" x 7.00" 10.54" 8.78" 102
77 TRAILER HUBS PRESET BY ARVINMERITOR Meritor TP HUB PART INNER BRG CUP OUTER BRG CUP STUD PST HM HM PST HM HM PST HM HM PST HM HM PRESET BY ARVINMERITOR HUB SERVICE KITS PART HUB TYPE COMMENTS R TP Spacer Kit R TP Bearing Set R TP Seal Kit R TP Complete Rebuild Kit - Bearings, Spacer and Seal PRESET BY ARVINMERITOR HUBCAPS PART HUB TYPE COMMENTS 3262-J-1388 TP Oil 3262-M-1391 TP Grease Note: Not available in hub/drum assemblies due to shipping protectors. Includes cups, cones, spacer, wheel seal and studs. 103
78 TRAILER HUBS PRESET BY ARVINMERITOR Meritor TN/TQ HUB PART INNER BRG CUP OUTER BRG CUP STUD PST HM HM PST HM HM PST HM HM PST HM HM PRESET BY ARVINMERITOR HUB SERVICE KITS PART HUB TYPE COMMENTS R TN/TQ Complete Rebuild Kit - Bearings, Spacer and Seal R TN/TQ Spacer Kit R TN/TQ Bearing Set R TN/TQ Seal Kit PRESET BY ARVINMERITOR HUBCAPS PART HUB TYPE COMMENTS 3262-K-1389 TN/TQ Grease 3262-L-1390 TN/TQ Oil Note: Not available in hub/drum assemblies due to shipping protectors. Includes cups, cones, spacer, wheel seal and studs. 104
79 CROSS REFERENCE LISTING BENDIX ERIE FORD BENDIX ARVINMERITOR ERIE ARVINMERITOR FORD ARVINMERITOR PART NO. PART NO. PART NO. PART NO. PART NO. PART NO C4Z1125A C4Z1125CA C4Z1125GC D5HZ1102A R D5HZ1102B R E3HZ1102A E4HZ1125A E4HZ1125A E4HZ1125C E4HZ1125D E6HZ1125F R E6HZ1125G R F0HZ1126C F4HZ1125A F4HZ1125C YC3Z2C026AA R GMC GMC ARVINMERITOR PART NO. PART NO R R R R R
Dayton Brake Drums Rotors Trailer Hubs Catalog PB-2006
Dayton Brake Drums Rotors Trailer Hubs Catalog PB-2006 Revised 05-03 Strength Power Speed Agility MERITOR PARTS. RIGHT FROM THE START. CONTENTS SteelLite X30 Brake Drum... 2 How to Use This Catalog...
TRAILER AXLE SPINDLE HARDWARE FRUEHAUF "PRO-PAR" AXLE AND MERITOR EARLY MODEL TP AXLE
TRAILER AXLE SPINDLE HARDWARE FRUEHAUF "PRO-PAR" AXLE AND MERITOR EARLY MODEL TP AXLE R001561 Lockwasher 12402, 42203, 5402, 65463, E1561, L1893, L893, M1051 PIN SIZE THICK O.D. I.D. DIA. LGTH 7/32" 5-1/16"
BRAKE DRUM AND ROTOR SERVICE INFORMATION
SERVICE INFORMATION To achieve maximum drum life and optimum performance, proper brake maintenance and brake balance are essential. Consult your truck or trailer manufacturer s maintenance manual for proper
CAST SPOKE WHEELS. Cast Spoke Trailer Wheels Complete With Brake Drums, Bearing Cups, Spacers, Clamps and Nuts
81 CAST SPOKE WHEELS Cast Spoke Trailer Wheels Complete With Brake Drums, Bearing Cups, Spacers, Clamps and Nuts WHEEL BEARING CUPS PART NO. DIMENSIONS INNER OUTER BRAKE SIZE WEBB NO. COMMENTS 15 INCH
High-Volume Brake Drum, Rotor, and Hub Catalog and Interchange
High-Volume Brake Drum, Rotor, and Hub Catalog and Interchange For Trucks, Trailers, Buses, and Other Equipment WE MAKE OVER 2,000 DIFFERENT BRAKE DRUMS DuraBrake Co. TABLE OF CONTENTS The DuraBrake Advantage...3
Section 6 Brake Drum Failure Analysis. Brake Drum Wear Conditions. What is Normal Wear? What is Deep or Excessive Wear? WARNING. Deep, Uniform Wear
Section Brake Drum 6 Failure Analysis WARNING To prevent serious eye injury, always wear safe eye protection when you perform vehicle maintenance or service. Figure 6.1 ASBESTOS AND NON-ASBESTOS FIBERS
HydRAUlic brake PROdUcT catalog quick RefeRence
HydRAUlic brake PROdUcT catalog quick RefeRence PB-99127 Supplement Revised 10/08 From 2003 through 2008 2003 60mm Twin Piston R42R12068 R42R12068 MD1010 66mm Twin Piston R42R12067 R42R12067 MD1010 70mm
HENDERSON WHEEL & WAREHOUSE SUPPLY. 2013 HEAVY DUTY STEEL TRUCK WHEEL CATALOG January 2013
HENDERSON WHEEL & WAREHOUSE SUPPLY 2013 HEAVY DUTY STEEL TRUCK WHEEL CATALOG January 2013 Hub Pilot 8-Hole and 10- Hole Wheels... Page 1 Hub Pilot Duplex Wheels... Page 2 Stud Pilot 6-Hole and 10-Hole
Heavy-Duty Break Drums. Maintenance & Installation Manual
Heavy-Duty Break Drums Maintenance & Installation Manual Since 1923, Gunite Corporation has been designing and manufacturing brake drums for the heavy-duty trucking industry. Today, Gunite continues to
Table of Contents BRAKE DRUMS. Hub & Drum Assembly Components... 20 CentriSet Trailer Hub Systems...21 CENTRIFUSE HUB & DRUM ASSEMBLIES
Table of Contents General Notes...2 BRAKE DRUMS CentriFuse Warranty..................................... 3 Genuine CentriFuse Advantages.................. 4 CentriFuse Lite Advantages......................
Tires and Wheels. Tires and Wheels. Common Tire Terms. Determing Wheel Offset. Determing Bolt Pattern. Dual Wheel/Rim Spacing
ommon Tire Terms Section : Aspect Ratio: Range: Overall Diameter: Static Radius: Design : width of a tire in millimeters measured on a rim with optimal width. A dimensional relationship of the tire s section
Gunite Disc Brake Rotors
Gunite Disc Brake Rotors Maintenance Manual Gunite is the industry leader in the development of brake system components for heavy-duty truck applications including air disc brake rotors. Gunite was the
Bendix Air Disc Brakes
Bendix Air Disc Brakes Optimum Performance. Optimum Engineering. A i r D r u m B r a k e s A i r D i s c B r a k e s A i r B r a k e C h a m b e r s S l a c k A d j u s t e r s H y d r a u l i c s A major
DiscPlus DX195 and DX225 Air Disc Brakes
Revised 11-04 Technical Bulletin Revised 1 Technical 11-04 Bulletin DiscPlus DX195 and DX225 Air Disc Brakes Inspection, Installation and Diagnostics Air Disc Brake Inspection Intervals and Procedures
The smart route to performance.
M e r i t o r T r a n s i t B u s a n d C o a c h A x l e s The smart route to performance. Meritor Transit Bus and Coach Axles FH-946 The Industry s Axle Leader. With more than a century of axle-manufacturing
Spicer Axles & Brakes ABIB-0302
Information Bulletin Bulletin Type: Parts / Service Information Topic: Dana LMS Hub Assembly Procedure Steer and Drive Axles Spicer Axles & Brakes ABIB-0302 Note: Bulletin ABIB-0302 replaces the original
2014 PRODUCT SPEC GUIDE
2014 PRODUCT SPEC GUIDE THE LIGHTWEIGHT INNOVATION LEADER INNOVATION IS IN OUR DNA This year, Alcoa is launching technology that s ready to shatter industry HEAVY-DUTY WITHOUT THE HEAVY. standards. But
TIRE & TUBE SECTION DEFINITIONS: OVERALL WIDTH SECTION HEIGHT (D) OVERALL DIAMETER (A) SECTION WIDTH (B) NOMINAL RIM DIAMETER (C)
TIRE & TUBE SECTION Knowing some basic facts about tire dimensions and sizes along with a few technical aspects of tire construction can help clear up much of the confusion many people have in understanding
TIE ROD END DESIGN TUTORIAL
TIE ROD END DESIGN TUTORIAL THE FOLLOWING IS A SIMPLIFIED STEP-BY-STEP GUIDE INTENDED TO ILLUSTRATE THE DECISIONS AND COMPROMISES INVOLVED IN DESIGNING A TIE ROD END. THE PROCESS FOR DESIGNING ANY BALL
Service Manual. For ConMet Hub & Rotor Assemblies HEAVY DUTY MEDIUM DUTY. For Hydraulic & Air Disc Brakes. PreSet Trailer Hub & Rotor Assemblies
Service Manual For ConMet Hub & Rotor Assemblies HD HEAVY DUTY MD MEDIUM DUTY For Hydraulic & Air Disc Brakes PreSet Drive Hub & Rotor Assemblies PreSet Trailer Hub & Rotor Assemblies PreSet Steer Hub
Chapter 18: Brakes and Clutches
Chapter 18: Brakes and Clutches Nothing has such power to broaden the mind as the ability to investigate systematically and truly all that comes under thy observation in life. Marcus Aurelius, Roman Emperor
Checking Wheel Brakes Wear
Issue 1 en 1 Checking Wheel Brakes Wear Contents Disc Brakes... 3 Removing the wheels... 4 Checking the Brake Pads... 5 Check brake disc thickness... 7 Checking brake disc for cracks... 8 Drum Brakes...
MERITOR WHEEL BEARING ADJUSTMENT SYSTEM FOR THE AFTERMARKET OPTIMAL WHEEL BEARING ADJUSTMENT. LONGER TIRE LIFE AND MORE TIME ON THE ROAD.
MERITOR WHEEL BEARING ADJUSTMENT SYSTEM FOR THE AFTERMARKET OPTIMAL WHEEL BEARING ADJUSTMENT. LONGER TIRE LIFE AND MORE TIME ON THE ROAD. Meritor and Temper. Together to Provide a Superior Bearing Adjustment
ALL NISSAN; BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR
Classification: Reference: Date: BR00-004b NTB00-033b August 30, 2004 ALL NISSAN; BRAKE NOISE/JUDDER/PEDAL FEEL DIAGNOSIS AND REPAIR This bulletin amends NTB00-033. This version amends the Brake Judder
PARTS SECTION. Section MF4
PARTS SECTION Section MF4 Wheels, Steering, Axle; hubs, rims, steering pumps, ALLIS CHALMERS RADIATOR HOSE ALLIS CHALMERS RADIATOR HOSE 70243014 180, 185, 190, 190XT 70248233 180, 185, 190, 190XT Radiator
INSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
FRICTION MATERIALS & BONDING SERVICES
FRICTION MATERIALS & BONDING SERVICES World Class Friction Materials & Bonding Services The Industry Leader Midwest Brake has been a leading supplier of non asbestos industrial friction material and bonding
Webinar Series. Committee. Disc Brake Wheels Off Inspection and Reline. Presents
1 APTA Bus Webinar Technical Series Maintenance Committee Webinar Series Presents Disc Brake Wheels Off Inspection and Reline January 21, 2015 2 Introduction Welcome to today s webinar in which we will
ACCESSORY PRODUCTS CATALOG. Driving Your Bottom Line.
ACCESSORY PRODUCTS CATALOG Driving Your Bottom Line. Table of Contents Heavy Duty Trucks - Chrome Accessories One-Piece Hub Cover System...2 Alcoa Wheel Kits...3-5 Alcoa Hug-A-Lug Nut Covers...5-6 Wheel
6,100 7,000 lb. Spring Axles
Typical Industries & Applications include: Recreational Vehicle Trailers Enclosed Trailers Cargo Vehicle Race Vehicle Open Utility Trailers Landscape Equipment Dump Trailers Construction Agricultural Equipment
Illustrated Parts List
Spicer Tandem Axles Illustrated Parts List AXIP0085a January 1994 Single Reduction, Dual Range, & Double Reduction Addendum 461, 462, 463, 521, 581 46,000-65,000 lbs Introduction Single Reduction w/wheel
Spicer Axles and Tire Pressure Management Systems
Spicer Axles and Tire Pressure Management Systems Spicer Fire and Rescue Vehicle Products Spicer Axle, Driveshaft, and Tire Pressure Management Systems Bendix Foundation Brake Systems Everything You Need.
MOPAR 8.75 REAR DIFFERENTIAL INFORMATION
MOPAR 8.75 REAR DIFFERENTIAL INFORMATION Sure Grip is the performance type of differential that enables both rear tires to turn under power for better launch traction. Sure Grip is the Chrysler name for
One and Two-piece Torque Rods and Replacement Bushings LIT NO: 45745-148
One and Two-piece Torque Rods and Replacement Bushings LIT NO: 45745-148 DATE: January 2008 REVISION: B HENDRICKSON ULTRA ROD PLUS Torque Rod Bonded Bushing Provides Longer Life Bonding makes a better
Freightliner AirLiner Suspension 32.05
Freightliner irliner Suspension 3.05 Ride Height djustment NOTICE Failure to adjust the suspension ride height could adversely affect driveline angles. lso, if the air springs are set too high, the driver
Illustrated Parts List
Spicer Tandem Axles Illustrated Parts List Spicer Single Reduction 34,000-45,000 lbs AXIP-0089 November 2004 Table of Contents TABLE OF CONTENTS Spicer Axle Parts Book.......... 2 Forward Tandem Axle Differential
SERVICE BULLETIN No.1065A
SERVICE BULLETIN No.1065A Circulate to listed addressees COACH MODEL BULLETIN TYPE MANUAL & SECTION PARTS BOOK REVISION : T2145 and C2045 : Product Improvement : Maintenance Manual: Chapter 4: Axles, wheels
Technical Data. 7. Bearing Fits. 7.1 Interference. 7.2 Calculation of interference F B LLLLLLLLL( A-54
Technical Data 7. Bearing Fits 7.1 Interference For rolling s the rings are fixed on the or in the housing so that slip or movement does not occur between the mated surface during operation or under. This
How Do I Replacing My Rear Brake Pads and Rotors?
How Do I Replacing My Rear Brake Pads and Rotors? WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary
Eliminator Vented Disc Brake Owners Manual
Eliminator Vented Disc Brake Owners Manual Eliminator Vented Disc Brakes Exclusive Features Whenever possible, the tendency is to use an aluminum alloy in order to reduce weight. These alloys are much
Trailer Axles. Applications and Specifications Guide. TP-8301 Revised 5-01 $2.50
Trailer Axles Applications and Specifications Guide TP-8301 Revised 5-01 $2.50 Table of Contents Section 1: Introduction..................................................... 1 Section 2: Applications.....................................................
Ford F-250 / 350 2-1/2 Coil Kit. Ford F-250, F350 2011-2015. Part#: 013255
Part#: 013255 Ford F-250 / 350 2-1/2 Coil Kit Ford F-250, F350 2011-2015 Rev.040815 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web/live chat: www.bds-suspension.com. E-mail: [email protected]
Rear wheel brakes, servicing. Стр. 1 из 45. Note:
Volkswagen Touareg - Rear wheel brakes, servicing Стр. 1 из 45 46-2 Rear wheel brakes, servicing Rear brakes, FN 44 brake caliper, servicing Note: After replacing brake pads, depress brake pedal firmly
DANA 30 MANUAL HUB CONVERSION KIT
DANA 30 MANUAL HUB CONVERSION KIT 12194 PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU BEGIN Your safety and the safety of other motorists is very important. Your Jeep is an off road capable vehicle
Determining the Right Molding Process for Part Design
Determining the Right Molding Process for Part Design How RIM Molding Advantages Compare with Traditional Production Technologies Page 2 Introduction This White Paper details the part production processes
Working Drawing and Assemblies. Chapter 10
Working Drawing and Assemblies Chapter 10 Objectives 1.Define working drawings. 2. Describe how working drawings are used in industry. 3. List the major components of a complete set of working drawings.
SECTION 2B WHEEL ALIGNMENT TABLE OF CONTENTS
SECTION 2B WHEEL ALIGNMENT TABLE OF CONTENTS Description and Operation... 2B2 Four Wheel Alignment... 2B2 Toein... 2B2 Caster... 2B2 Camber... 2B2 Diagnostic Information and Procedures... 2B3 Tire Diagnosis...
2007 Hummer H3. 2007 BRAKES Disc Brakes - H3. Fastener Tightening Specifications Specification Application
2007 BRAKES Disc Brakes - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Backing Plate Bolts 135 N.m 100 lb ft Brake Hose
TRANS-05, Torque Tube Removal, Rebuilding, and Installation
TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket
1. Lay out 2 pieces of 7/8" tubing and mark for bending as shown. Remember that the bend is in the shaded area as shown below in Figure 1.
MINI BIKE PLANS Page 1 INTRODUCTION Before starting to build your Mini-Bike, be sure that you have all the parts shown on the material list. You will note that tubing has been used in the construction.
Understanding Wheel Offset and Backspacing
Understanding Offset and Backspacing Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs.
FOR ANY QUESTIONS, PLEASE CALL US @ 727.347.9915 M-F 8:00a.m.-8:00p.m. EST. REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915
REAR BRAKES 1 AEROSPACE COMPONENTS 727.347.9915 REAR BRAKES Before getting started, remove all stock braking components. Pre-assembly of parts: Clean the bolts and the threads in the hat with acetone.
Design and Analysis of Wheel Rim using CATIA & ANSYS
Design and Analysis of Wheel Rim using CATIA & ANSYS P. Meghashyam 1, S. Girivardhan Naidu 2 and N. Sayed Baba 3 1,2,3 Scholar /Department of Mechanical Engineering, JNTUA/Madanapalle Institute of Technology
Wheel Accessory Products Catalog
Wheel Accessory Products Catalog Table of Contents Heavy Duty Trucks - Chrome Accessories One-Piece Hub Cover System...2 Alcoa Wheel Kits...3-4 Alcoa Hug-A-Lug Nut Covers...5-6 Heavy Duty Trucks - Maintenance
MUSTANG II IFS COMPLETE PARTS PACKAGE
MUSTANG II IFS COMPLETE PARTS PACKAGE Your Southern Rods & Parts Mustang II IFS Parts Package contains the following items: 1 pr) Upper Control Arms (2023) 1) Upper Arm Bolt Kit (MP-001-A) 1 pr) Lower
1993 SUSPENSION Volkswagen Front. EuroVan
Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Front EuroVan DESCRIPTION FWD independent suspension is an double-wishbone type with torsion bars mounted on upper control arm. Wheel is supported
(A5) Brakes Sample Questions and Answers
(A5) Brakes Sample Questions and Answers Answers to these questions are found beginning on page 4 of this document 1. Two technicians are discussing a problem where the brake pedal travels too far before
Rear Disc Kit. Front Caliper
Caliper and Wheel Kit 52-0600 1973-85 FX-FLH Chrome Rear Wheel/Brake Assembly includes chrome 16 x 3.0 Wheel Assembly, chrome caliper, chrome 51T sprocket with bolts, 10 or 11 1 /2 rear drill brake disc,
WHEELS & RIMS TO KEEP YOUR COMPANY MOVING FORWARD
WHEELS & RIMS TO KEEP YOUR COMPANY MOVING FORWARD Trailers: RV - Utility - Cargo - Marine - Manufactured Housing Lawn & Garden: Tractors - Mowers Agricultural: Farm Equipment Meets DOT Specifications Powder
FEA Analysis of a Caliper Abutment Bracket ME 404
FEA Analysis of a Caliper Abutment Bracket ME 404 Jesse Doty March 17, 2008 Abstract As braking forces are applied at the wheel of an automobile, those forces must be transmitted to the suspension of the
Procedures and Intervals to Inspect the Wheel Ends and Tighten the Spindle Nuts on Meritor TL Series Trailer Axles with Unitized Wheel Ends
Technical Bulletin Revised 1 Technical 02-11 Bulletin Revised 02-11 Procedures and Intervals to Inspect the Wheel Ends and Tighten the Spindle Nuts on Meritor TL Series Trailer Axles with Unitized Wheel
Class 5 to 7 Truck and Bus Hydraulic Brake System
Class 5 to 7 Truck and Bus Hydraulic Brake System Diagnostic Guide 1st Edition * 5+0 Important Service tes The information in this publication was current at the time of printing. The information presented
4,000 6,000 lb. Spring Axles
Typical Industries & Applications include: Recreational Vehicle Trailers Enclosed Trailers Cargo Vehicle Race Vehicle (Stacker) Open Utility Trailers Landscape Equipment Sport Utility motorcycle, quad
7.3 Fit selection. Inner ring: Rotating. Outer ring: Stationary. Inner ring: Stationary. Outer ring: Rotating. Inner ring: Stationary
7. Bearing Fits 7. Fitting For rolling s, inner and outer rings are fixed on the or in the housing so that relative movement does not occur between fitting surfaces during operation or under. This relative
The hunt for replacement disc rotors for the 69-70 Impala.
The hunt for replacement disc rotors for the 69-70 Impala. A few years back, upon starting my chassis restoration, I had decided that my 69' would need disc brakes in place of drums on the front. A little
Service Information for. With patented stainless steel wheel bearing protectors.
Service Information for With patented stainless steel wheel bearing protectors. Spindle Spring Loaded Seal Bearing Cap Hub Patent No. 5,054,859 Check Valve Overflow Cavity Grease Fitting Stainless Steel
These features have made Lo Torc valves the choice of high pressure plug value users, worldwide:
LO TORC Plug Valve The high value, dependable performance, and low maintenance requirements of Halliburton Lo Torc valves can help reduce overall operating costs and help cut downtime. These features have
Design of a Rope Brake Dynamometer
Middle-East Journal of Scientific Research 0 (5): 650-655, 014 ISSN 1990-933 IDOSI Publications, 014 DOI: 10.589/idosi.mejsr.014.0.05.11356 Design of a Rope Brake Dynamometer R. Gopinath Department of
ARVINMERITOR UNITIZED FRONT WHEEL HUB INSPECTION AND MAINTENANCE
SERVICE BULLETIN (Also applies to Mack Trucks Australia) NUMBER: SB-423-002 DATE: 8/23/02 MODEL: All with FF981 Front Axle ARVINMERITOR UNITIZED FRONT WHEEL HUB INSPECTION AND MAINTENANCE The ArvinMeritor
SLACK PERFORMANCE KARTS
SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction
Two most common lock nut groups: 1-Prevailing Torque Type Lock Nuts:
Two most common lock nut groups: 1. PREVAILING TORQUE a design feature of the lock nut produces friction between threads of mated components thereby increasing the force needed to tighten as well as loosen
KNIFE GRINDER MATERIALS LIST & CONSTRUCTION TIPS by Michael Clerc [email protected]
KNIFE GRINDER MATERIALS LIST & CONSTRUCTION TIPS by Michael Clerc [email protected] Materials List Minimum tools required: Drill press & Drill bits ("#7", "F", 5 / 16 ", ¼", 17/64", ½", "O", 1") Tap Handle
TIRE BASICS TIRE MOUNTING AND DEMOUNTING
Tire mounting and demounting can be dangerous and should only be performed by a trained tire specialist using proper tools and procedures. Be sure to review your training manual and refer to the RMA wall
1.8 CRANKSHAFT OIL SEALS
SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the
Valve Live Loading With Belleville Springs. Belleville Springs for Valve Live Loading
Valve Live Loading With Belleville Springs What is Valve Live Loading? The addition of Belleville Springs to the gland follower studs to maintain the packing load of the valve over time. What s In The
(A4) Suspension and Steering Sample Questions and Answers
(A4) Suspension and Steering Sample Questions and Answers Answers to these questions are found beginning on page 4 of this document 1. Two technicians are discussing the replacement of an inner tie rod
MASTER CYLINDER. Section 2. Master Cylinder. Tandem Master Cylinder. Master Cylinder
MASTER CYLINDER Master Cylinder The master cylinder converts the motion of the brake pedal into hydraulic pressure. It consists of the reservoir tank, which contains the brake fluid; and the piston and
Owner s Manual Read and keep this manual. Patents World Wide
Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2008 All Rights Reserved The following manual is provided to assist
2,500 3,700 lb. Spring Axles
Typical Industries & Applications include: Recreational Vehicle Trailers Enclosed Trailers Cargo Vehicle Race Vehicle Open Utility Trailers Landscape Equipment Sport Utility motorcycle, quad and tri wheel
Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800. (installation performed on 60 Model) (Right) (Left)
740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800 A (installation performed on 60 Model) Item Description Qty A Rotor 4 B Gear Box, L 2 C
Fig 1 Power Transmission system of Tractor
POWER TRANSMISSION SYSTEM Transmission is a speed reducing mechanism, equipped with several gears (Fig. 1). It may be called a sequence of gears and shafts, through which the engine power is transmitted
M113 VEHICLE FAMILY RUBBER TRACK INSTALLATION INSTRUCTIONS SOUCY TRACK SYSTEM 04-M113-1ENS (SPLIT IDLER) Litho d in Canada 1 04-M113-1ENS
M113 VEHICLE FAMILY RUBBER TRACK INSTALLATION INSTRUCTIONS (SPLIT IDLER) 1 # TABLE OF CONTENTS List of parts and tools................................................3 Installation of complete kit...................................................5
1/29/2008 DR70. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43
DR70 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43 CYLINDER & CYLINDER HEAD 1 DR70-001 883099044472 CYLINDER 1 1 2 DR70-002 883099044489 GASKET, CYLINDER 1 1 3 DR70-003 883099044496
Solid shape molding is not desired in injection molding due to following reasons.
PLASTICS PART DESIGN and MOULDABILITY Injection molding is popular manufacturing method because of its high-speed production capability. Performance of plastics part is limited by its properties which
Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 900 Crew. (Right) (Left)
740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 900 Crew A Item Description Qty A Rotor 4 B Gear Box, L 2 C Gear Box, R 2 D Gasket 4 E Cap
Open Wheel. Brake Kits and Components. Braking Solutions for a World in Motion TM
Open Wheel Brake Kits and Components Braking Solutions for a World in Motion TM CATALOG Welcome to Wilwood s Open Wheel Brake Kits and Components Catalog. This catalog highlights disc brake kits and components
Machine devices, jig devices
Machine devices, jig devices 853 K0697 Rolled thread studs DIN 6379 Material: Tempered steel. KIPP Rolled thread studs DIN 6379 Order No. D L B1 B2 Approx. weight g Surface finish: Thread rolled. Class
SVE BULLETIN. 2016 E-Series Wheelbase Modification Driveline Noise Reduction
Q-238 SVE BULLETIN SPECIAL VEHICLE ENGINEERING BODY BUILDERS ADVISORY SERVICE E-Mail via Website: www.fleet.ford.com/truckbbas (click "Contact Us") Toll-free: (877) 840-4338 QVM Bulletin: Q-238 Date: 03
PARTS LIST RTR READY-TO-ROLL
PARTS LIST RTR READY-TO-ROLL LIT NO: L949 DATE: August 2015 REVISION: D TABLE OF CONTENTS DRUM BRAKE COMPONENTS.... 3 Brake Adjusters INTRAAX and VANTRAAX... 3 Automatic Brake Adjusters TRLAXLE... 3 Manual
RV TIRE MAINTENANCE AND INFLATION TIPS
RV TIRE MAINTENANCE AND INFLATION TIPS PROTECTING YOUR INVESTMENT ON THE ROAD Maintaining proper air pressure in RV tires is the best way to enhance tread life and overall performance. Improper tire inflation
Cane Creek Double Barrel Instructions
Cane Creek Double Barrel Instructions Congratulations on your purchase of the Cane Creek Double Barrel (CCDB) rear shock. Developed in partnership with Öhlins Racing, the Double Barrel brings revolutionary
*Specify Oversize When Ordering
Cylinder Block Deck Cracks On Caterpillar 3208 Engines and Caterpillar explain how to inspect the Caterpillar 3208 engines for block cracks. Part No. Location Insert OD Size Depth Tapered ID 3906854 Intake
American National, Unified Screw Threads
C h a p t e r 9 American National, Unified Screw Threads In this chapter, you will learn the following to World Class standards:! Why Use Fasteners! The Text Designation for the Unified National Thread!
INSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)
INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE
KELGATE BRAKES - price list for 2014 Page 1
KELGATE BRAKES - price list for 2014 Page 1 Description GBP (Kgms) Disc's:- FV = Fully Vented RV = Radially Vented New systems are supplied dry. 02-9028 Charge for bleeding per caliper 18.00 00-8080 GTK'
CONGRATULATIONS! TABLE OF CONTENTS. 1 Safety Warnings 2 About Your Wheels 3 Setting Up Your Wheels 7 Care and Cleaning 8 Warranty
WHEEL MANUAL CONGRATULATIONS! Congratulations on your purchase of Oval Concepts Wheels. Developed to perform at a high level, it is important that you follow the operation and maintenance instructions
LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions
LORTONE LU6X-130 Item # 061-092 LU6X Basic Item # 061-090 LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions Introduction The LU6X is one the most versatile pieces of equipment
Meritor Rear Axle Seals
System: Axles, Driven Bulletin #: 22-4 Date: March 9, 2005 Meritor Rear Axle Seals Accompanying this bulletin is information on the new Multiple Lip Seals used in the Meritor rear drive axles. Please utilize