Blocks and Holders. Ordering Information
|
|
- Brett Small
- 7 years ago
- Views:
Transcription
1 FuSE blocks OVERVIEW Description Littelfuse offers a comprehensive line of fuse blocks that incorporate many benefits such as indication, snap torelease, DIN-Rail mounting and universal mounting holes. 5. Select the type of wire termination Three types of wire termination are available: *for use with spade lugs or ring terminals with Pressure Plate*for use with solid or stranded wire without terminal. Recommended where vibration will be a factor Box Lugfor use with all types of solid wire and lass B and lass stranded wire. The most durable, but not for use with welding cable or other rope-stranded conductors. * 4 Quick onnect terminals rated for up to 20 amperes are available on the Midget and lass fuse blocks. New Options Available Reduced FootprintSave space with designs up to 5% smaller in width Increase safety and reduce downtime with built-in local neon indication Universal Mounting HolesSimplify replacement with universal mounting options DIN Rail MountableEase installation with a 5 mm hat DIN Rail mounting option One-Hand ReleaseSave time by using only one hand for a simple release from DIN Rail Fuse Block Selection The following guidelines should help simplify the selection of proper fuse blocks:. Determine the system voltagesince fuses are selected on the basis of sys tem voltage, fuse blocks are selected to match the voltage rating of the fuse. 2. Determine the design short-circuit currentif available short-circuit current cannot be determined, or if it will vary with equip ment location, select fuses with a,000 ampere interrupting rating (A.I.R.) and mating fuse blocks with a withstand rating of,000 amperes for maximum safety. w th Pressure P ate (P) (S). Decide on the number of poles in each blockthe number of poles for each set of fuses is determined by the characteristics of the circuit. 7. Determine if block should be DIN Rail mountedmany of the new Littelfuse fuse blocks are DIN Rail mountable. Be sure to look to corresponding tables to match the correct part number on the following product pages. 8. Determine if fuse clips need to be re in forced Fuse clips may have a tendency to lose some of their tension over a period of time. This may be prevented by specifying reinforced fuse clips. Ordering Information Box Lug () The Littelfuse fuse block part number con sists of the below skeleton. Please refer to UL lass Tables for specific information.. Determine the type and ampere rating of the fuse to be usedthe fuse ampere rating, opening characteristics (fast acting or time-delay) and size are important considerations in fuse selection. Fuse blocks may be used with a fuse rated at the corresponding amperage rating or below. For example, a fuse block rated at 0 amperes may be used with a fuse rated from 0 to 0 amperes. 4. Determine if NE, SA, UL, or other requirements are applicableany of these requirements should be obtained from the approving agency in advance of fuse and fuse block selection. For all lass R, H, J, and T Fuse blocks For all lass, G, and Midget-Style These new fuse blocks replace previous Littelfuse fuse blocks that had very similar part numbers for customer convenience. The only change is an F has been added as the second character in the new block part numbers. aution: Littelfuse indicating fuse holders are intended to quickly identify open fuses while power is still applied. Only qualified electrically trained technicians should replace fuses and follow standard OSHA and NFPA 70E safe work practices, such as Lock-Out and Tag-Out procedures and verification before replacing any fuses in indicating fuse holders. 202 Littelfuse POWR-GARD Products atalog 8
2 LF Series Indicating Fuse Blocks Smaller Footprint Provides Space Savings DIN-Rail Mounting Eases Installation Improves Functionality An of Value The Littelfuse and overs offer generous space savings and a greater value over previous generations. View the different series classes for available indication, snap-to-release DIN rail mounting, universal mounting holes and touch-safe covers Littelfuse POWR-GARD Products atalog
3 LF Series lass H/K5 and r Fuse blocks 250 V 00 V Description The Littelfuse lass H/K5 and R blocks offer many benefits such as indication, snap-to-release DIN rail mounting and universal mounting holes. lass H and lass R fuse blocks are dimensionally the same, but lass R blocks incorporate a rejection feature, which only allows lass R fuses to be inserted. Features/Benefits Universal mounting holes for easy replacement offered on most 250 V and 00 V versions One hand release from DIN rail for ferrule style fuses Reinforced fuse clips are standard on all lass H and lass R fuse blocks overs available for 00 A and lower to enhance safety Web Resources Sample requests, downloadable AD drawings and other technical information: /lfh /lfr /fuseblocks Ordering Information (lass H 250 V) Specifications Voltage ere s Leakage urrent Withstand 250 V, 00 V 0-00 A <0. ma at 00 V lass H: 0 ka RMS SYM lass R: ka RMS SYM Flammability UL94 V-0 Approvals UL Listed (File No. E472) SA ertified (File No. LR7) Environmental Recommended Fuses RoHS ompliant, Lead (Pb) Free lass H/K5 Blocks 250 V NLN... 2 RLN lass R Blocks 250 V FLNR/FLNR_ID... 8 KLNR... 5 LLNRK... 4 lass H/K5 Blocks 00 V NLS... 2 RLS lass R Blocks 00 V FLSR/FLSR_ID... 8 KLSR... 5 LLSRK/LLSRK_ID... 4 IDSR part Box pressure number Lug Plate LFH2500 P S -4 AWG 2 LFH25002 P S 2.8 N-m (25 in-lbs) P 0-4 AWG LFH2500 P S S 0-22 AWG LFH2500 ID 5. N-m (50 in-lbs) 2-4 AWG 2.8 N-m (25 in-lbs) -4 AWG 2 LFH25002 ID LFH2500 ID LFH2500 LFH2500 ID ID. N-m (20 in-lbs) 2/0- AWG 4.5 N-m (40 in-lbs) 8 AWG 4.0 N-m (5 in-lbs) 0-4 AWG Type U Only DIN Rail OVer 25 LFH2500FB U-AL 25 LFH2500FB U-AL 0 LFH2500FB LFH25 LFH25. N-m (275 in-lbs) 250 kcmil- U-AL 0 LFH25 LFH25. N-m (275 in-lbs) (2) 50 kcmil-/0 U-AL 0 LFH LFH N-m (75 in-lbs) (2) 500 kcmil-4 U-AL 0 Note: Reinforcing springs standard on all lass H fuse blocks. *overs sold individually. One cover needed for each pole Littelfuse POWR-GARD Products atalog
4 LF Series lass H/K5 And R Fuse blocks Ordering Information (lass H 00 V) LFH000 ID PID SID -4 AWG 2 LFH0002 ID PID SID 2.8 N-m (25 in-lbs) P 0-4 AWG LFH000 ID PID SID S 0-22 AWG LFH000 ID 5. N-m (50 in-lbs) 2-4 AWG 2 LFH0002 ID LFH000 ID 2.8 N-m (25 in-lbs) -4AWG LFH000 LFH000 ID ID Note: Reinforcing springs standard on all lass H fuse blocks. Note: Reinforcing springs standard on all lass R fuse blocks. Note: Reinforcing springs standard on all lass R fuse blocks. *overs sold individually. One cover needed for each pole. LFH0 LFH0 LFH0 LFH0 LFH000 LFH000 Ordering Information (lass R 250 V) Terminal Type U Only Snap to release OVer 0 LFH000FB U-AL 0 LFH000FB. N-m (20 in-lbs) 2/0-AWG 4.5 N-m (40 in-lbs) 8 AWG U-AL 0 LFH000FB 4.0 N-m (5 in-lbs) 0-4 AWG. N-m (275 in-lbs) 250 kcmil- U-AL 0. N-m (275 in-lbs) (2) 50 kcmil-/0 U-AL N-m (75 in-lbs) (2) 500 kcmil-4 U-AL 0 Snap OVer Type to release LFR2500 P S -4 AWG 2 LFR25002 P S 2.8 N-m (25 in-lbs) P 0-4 AWG U Only 25 LFH2500FB LFR2500 P S S 0-22 AWG LFR2500 ID 5. N-m (50 in-lbs) 2-4 AWG 2 LFR25002 ID LFR2500 ID 2.8 N-m (25 in-lbs) -4 AWG U-AL 25 LFH2500FB ID. N-m (20 in-lbs) 2/0- AWG LFR N-m (40 in-lbs) 8 AWG U-AL LFR2500 ID 4.0 N-m (5 in-lbs) 0-4 AWG 0 LFH2500FB LFR25 LFR25. N-m (275 in-lbs) 250 kcmil- U-AL 0 LFR25 LFR25. N-m (275 in-lbs) (2) 50 kcmil-/0 U-AL 0 LFR2500 LFR N-m (75 in-lbs) (2) 500 kcmil-4 U-AL 0 Ordering Information (lass R 00 V) LFR000 ID PID SID -4 AWG 2 LFR0002 ID PID SID 2.8 N-m (25 in-lbs) P 0-4 AWG LFR000 ID PID SID S 0-22 AWG LFR000 ID 5. N-m (50 in-lbs) 2-4 AWG 2 LFR0002 ID LFR000 ID 2.8 N-m (25 in-lbs) -4 AWG Type U Only Snap to release OVer 0 LFH000FB U-AL 0 LFH000FB. N-m (20 in-lbs) 2/0- AWG LFR000 ID 4.5 N-m (40 in-lbs) 8 AWG U-AL LFR000 ID 4.0 N-m (5 in-lbs) 0-4 AWG 0 LFH000FB LFR0 LFR0. N-m (275 in-lbs) 250 kcmil- U-AL 0 LFR0 LFR0. N-m (275 in-lbs) (2) 50 kcmil-/0 U-AL 0 LFR000 LFR N-m (75 in-lbs) (2) 500 kcmil-4 U-AL Littelfuse POWR-GARD Products atalog 87
5 LASS H/K5 AND R FuSE blocks Dimensions mm (inches) 00 V 0 A 8.4 [.5] 2.5 [.85] 7. [2.88] 9.2 [.7] 5. [2.0].8 [.] 4. [.2].4 [.25] 07.9 [4.25] 8.4 [.40] 75.9 [2.99] 52.5 [2.07] 20.7 [.82].7 [.5] 27. [5.00] 8. [4.7] 5.0 [2.20] 47. [.87] R.4 [.] R2. [.0] 00 V 0 A 2.4 [.28] 29.8 [.7] 9.9 [.78].4 [.45] 4.8 [.7] 8. [.29] 2.2 [4.85] 9.5 [2.74] 09. [4.0] 59. [2.5] 99.4 [.9] 59.7 [2.5] 22.9 [.90] 84.2 [7.25] 4. [5.0] 55.2 [2.8] 74.2 [2.92] R.4 [.].2 THRU V 00 A 8 [ ] 9 [ 77] 5 0 [ 59] 5 4 [2 0] 45 [5 72] 25 7 [4 95] 07 0 [4 2] 79 8 [ 4] 0 [2 40] 0 [2 0] 22 9 [ 90] 4 [2 54] R 4 [ ] 72 8 [ 80] 228 [9 00] Littelfuse POWR-GARD Products atalog
Terminal Blocks & Power Distribution Terminal Blocks. Make your connection
Terminal Blocks & Power Distribution Terminal Blocks Make your connection IEC TERMINAL BLOCKS PRODUCT SPOTLIGHT Leading the industry in efficiency and productivity, the Bulletin 1492 family of IEC terminal
More informationDatasheet. AC Outlet DIN-Rail Mountable Receptacles
Datasheet AC Outlet DIN-Rail Mountable Receptacles DIN-rail receptacles, 5A, 15A and 20A power outlets, provide a convenient power source for portable computers or test devices for in-the-panel troubleshooting.
More informationTerminal Blocks 9080LBA Power Distribution Blocks Copper or Aluminum Wire
9080LBA Power Distribution Blocks Copper or Aluminum Wire Class 9080 Miniature Standard Amperage Rating - CU Wire 115 amp. 115 amp. 175 amp. 175 amp. Amperage Rating - AL Wire 90 amp. 90 amp. 135 amp.
More informationElectronic overload relay EF19 and EF45
Data sheet Electronic overload relay EF19 and EF45 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays. Motor
More informationsolar photovoltaic installations
onnecting the Power of the Sun Solar ombiner Boxes for Solar Photovoltaic Installations Solar combiner boxes for solar photovoltaic installations Solar energy is heating up Interest in renewable energy
More informationwww.littelfuse.com www.littelfuse.com/fuseblocks LF SERIES FUSEBLOCK CROSS REFERENCE
www.littelfuse.com www.littelfuse.com/fuseblocks NEW Littelfuse LF SERIES FUSEBLOCK CROSS REFERENCE LIST Power Fuses Medium Voltage Fuses Midget Fuses Telecom Fuses Semiconductor Fuses Fuseblocks & Holders
More informationPower Distribution & Terminal Blocks
Power Distribution & Terminal Section Contents Page Selection table for SCCR PDBs & Power terminal blocks................................ 294 Power distribution blocks Series PDBFS enclosed, with high
More informationManual motor starter MS116
Data sheet Manual motor starter MS116 Manual motor starters are electromechanical devices for motor and circuit protection. These devices offer local motor disconnect means, manual ON/ OFF control, and
More informationwhite paper Ferrules: Your Best Insurance Against Costly Connection Failure Executive Summary
Ferrules: Your Best Insurance Against Costly Connection Failure white paper Executive Summary Thanks to its superior flexibility, longer flex life*, and resistance to vibration, insulated stranded wire
More information.062 [1.57] Commercial Pin and Socket Connectors
Pin and Socket onnectors MP Product Facts Polarized avity identification Low contact-mating force Dual locking lances Detent and positive locking ontacts available in brass and phosphor bronze with tin
More informationFuses for Semiconductor Protection - Cylindrical Fuses. Class: Voltage ratings: Current ratings: Standards: Approvals: Features and Benefits
Fuses for Semiconductor Protection - Cylindrical Fuses SIBA cylindrical Ultra-Rapid fuses are available in six different sizes They can be ordered with an integral striker for blown fuse indication or
More informationElectronic overload relay EF65, EF96 and EF146
Data sheet Electronic overload relay EF65, EF96 and EF146 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays.
More informationAF09-30-22-.. / AF09Z-30-22-.. 2-stack 3-pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101403D0201 24/03/11 AF09-30-22-.. / AF09Z-30-22-.. 2-stack 3-pole Contactors AC / DC Operated - with Screw Terminals AF09(Z) contactors are used for controlling power circuits
More informationUncompromising safety and comfort The next generation of miniature circuit breakers MCB S 200/S 200 M
Uncompromising safety and comfort The next generation of miniature circuit breakers MCB S 200/S 200 M The details make the difference MCB S 200/S 200 M A range designed to ensure efficiency and protection
More informationCAT ATC POWER BREAKER & POWER CASE SWITCH AUTOMATIC TRANSFER SWITCH
CAT ATC POWER BREAKER & POWER CASE SWITCH AUTOMATIC TRANSFER SWITCH Cat transfer switches are designed for a variety of standby power applications. They provide flexibility, reliability and value in a
More informationCONDUCTOR SHORT-CIRCUIT PROTECTION
CONDUCTOR SHORT-CIRCUIT PROTECTION Introduction: This paper analyzes the protection of wire from fault currents. It gives the specifier the necessary information regarding the short-circuit current rating
More informationYour Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592. * see variants. Applications.
Safety Technique SAFEMASTER Emergency Stop Module BG 5924, IP 5924 Your Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592 BG 5924 IP 5924 Product Description
More informationAllen-Bradley 1397 400-600HP AC Line Filter Kit
Installation Instructions IN Allen-Bradley 1397 400-600HP AC Line Filter Kit Cat. Nos. 1397-LF600 What This Option Provides What This Kit Contains This option is intended to be applied when the primary
More informationRM17TE 183...528 V AC. Main. Product or component type. Product specific application. Relay monitored parameters 250 V DC 5 A DC
Characteristics multifunction control relay RM17-TE - range 183..528 V AC Complementary Reset time Maximum switching voltage Minimum switching current Maximum switching current [Us] rated supply voltage
More informationPhotovoltaic System Overcurrent Protection
Photovoltaic System Overcurrent Protection Photovoltaic System Overcurrent Protection Introduction Solar Photovoltaic (PV) systems have, over the last fifty years, evolved into a mature, sustainable and
More informationXG2. Flat Cable Connectors for PCBs. Achieve Total Cost Reduction through High-density Mounting and Reduced Wiring. Terminal Arrangement
Flat Cable Connectors for PCBs XG2 Achieve Total Cost Reduction through High-density Mounting and Reduced Wiring IDC connections allow you to wire all terminals at once without terminating the cable. Can
More informationElectronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact The CT-AHD.12 is an electronic time relay with OFF-delay. It is from the CT-D range. With their MDRC profile and a width of only
More informationUniversal MATE-N-LOK Connectors
Product Facts Pins and sockets can be intermixed in the same housing Positive polarization Rear cavity identification completely enclosed in housings Positive locking housings Insulation capability to.00
More informationEmergency stop As an emergency switching off/emergency stop device. Standards According to IEC/EN 60204-1, VDE 0113 Part 1
MainswitchSurfacemounting Partno. P3-63/I4/SVB Articleno. 207343 CatalogNo. SP3-063-I4CRQ IP65 Deliveryprogramme Product range Switch-disconnectors Basic function Main switches Maintenance switches Manual
More informationpicomax The Pluggable Connection System
picomax The Pluggable Connection System TECHNOLOGY THIS SPECIALIZED CAN T MEET ALL REQUIREMENTS. YES IT CAN. CONTENTS picomax Pin spacing: 3. mm/0.138 in;.0 mm/0.197 in; 7. mm/0.29 in Versatile Pluggable
More informationPositive-guided relay outputs: 3 safety contacts (N/O), instantaneous. 1 auxiliary contact (N/C), instantaneous
Safety relay for monitoring E-STOP pushbuttons. Approvals Unit features Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Safe separation of
More informationMini Motor Contactor J7KNA Main contactor Accessories Approved Standards Standard Guide No (US,C) Ordering Information tage Model Number Legend gear
Mini Motor Contactor J7KNA ) Main contactor AC & DC operated Integrated auxiliary contacts Screw fixing and snap fitting (35 mm DIN-rail) Range from 4 to 5.5 (AC 3, 380/415V) 4 -main pole version (4 AC
More information3RT1015-1BB41 CONTACTOR, AC-3 3 KW/400 V,
Automation Technology > Industrial Controls > Switching Devices > Contactors and Contactor Assemblies > Power Contactors for Switching Motors > Contactors SIRIUS 3RT10, 3-pole, 3... 250 kw 3RT1015-1BB41
More informationTerminal Blocks. BA Series. Specifications. Model BA111T BA211T BA311T BA411S
BA Series BA Series Specifications Key features: Self-contained: end plates are not required Rugged heavy-duty construction Current capacities up to 40A 3-pole units available as 1 piece (no endplates
More informationMILLENIUM INSTALLATION MANUAL NTR 735 A. Simple Automation Control Module (MAS)
MILLENIUM Table of contents 1. INTRODUCTION 1 2. HARDWARE DESCRIPTION 2 3. INSTALLATION 5 4. CONNECTION 6 5. USER SAFETY AND PROTECTION OF EQUIPMENT 8 1. Introduction The MILLENIUM series has been designed
More informationMini Circuit Breakers, Fuse Blocks, and Electronic Circuit Protection
Technical Data Mini Circuit Breakers, Fuse Blocks, and Electronic Circuit Protection Topic Page 1489-M Miniature Circuit Breakers 2 1492-SP Supplementary Protectors 15 1492-D Circuit Breakers 27 188 Regional
More informationOwner s Manual. For Automatic Transfer Switch. 100-200 Amp, Service Entrance/Non-Service Entrance
Owner s Manual For Automatic Transfer Switch 100-200 Amp, Service Entrance/Non-Service Entrance Model Numbers RTST100A3 RTSP100A3 RTST150A3 RTST200A3 RTSP200A3 MODEL NUMBER: SERIAL NUMBER: DATE PURCHASED:
More informationR.C.C.B. s two-pole LEXIC
87045 LIMOGES Cedex Telephone : (+33) 05 55 06 87 87 Fax : (+ 33) 05 55 06 88 88 R.C.C.B. s two-pole LEXIC 089 06/09/10/11/12/15/16/17/18/ 27/28/29/30/35, CONTENTS PAGES 1. Electrical and mechanical characteristics...
More informationProduct and functional description
Product and functional description The KNX / DALI gateway N 141/02 is a 4 MU wide, DINrail mounted KNX device with one DALI interface to which up to 64 DALI actuators (e.g. DALI ballasts) can be connected
More informationThis product can be assembled to the baseplate maintaining 5 mm center-to-center spacing. Thus any number of poles can end-to-end stack.
page 1/5 Plug-in Screw Connector System for Printed Circuit Boards 950-NLFL-DS 5.00 mm (0.197 in) Spacing - 2-12 poles PICTURES 950-NLFL-DS 950-NLFL & 971-SLK TECHNICAL INFORMATION Description This two
More informationLC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 65 A - 220 V AC coil
Product data sheet Characteristics LC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 -
More informationNF71E-.. / NFZ71E-.. Contactor Relays AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101433D0201 28/03/11 NF71E-.. / NFZ71E-.. Contactor Relays AC / DC Operated - with Screw Terminals NF(Z) contactor relays are used for switching auxiliary and control circuits.
More informationBulletin 150 Smart Motor Controllers SMC-3 Smart Motor Controller
Overview/Modes of Operation Bulletin 150 Smart Motor Controller The SMC-3 is a compact, simple to use, solid-state motor controller designed to operate 3-phase motors. It features a built-in overload relay
More informationCable Tray Selection-
Cable Selection- For allowable cable types see the Appendix page A-9. The following guidelines are based on the 2002 National Electrical Code, Article 392. I) Number of Multiconductor Cables rated 2000
More informationD7 Series Standard and Full Featured. Standard DPDT 24V AC 120V AC 240V AC 12V DC 24V DC 120V AC 110V DC 240V AC 6V AC 6V DC 12V AC 12V DC 24V AC
April 00 D Series Standard and Full Featured - Catalogue Number Structure Table -. D Series Catalogue Numbering System Family Type DPR = Standard Relay DPF = Full Featured Relay Contact Configuration =
More informationRM35UA13MW. range 15..600 V. Main. Product or component type. Relay monitored parameters
Characteristics multifunction voltage control relay RM35-U - range 15..600 V Complementary Reset time Maximum switching voltage [Us] rated supply voltage Supply voltage limits Power consumption in W Main
More information38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical Relays
More informationTerminal Blocks. BNH/BN Series. Specifications. Model BNH10W BNH15MW BNH15LW BNH30W
BNH/BN UL Recognized File No. E78117 CSA Certified File No. LR64803 BNH/BN Series Specifications Key features: Touch-down terminals with spring-loaded captive screws Jumpers available up to 50A model Fuse
More informationDC disconnects for solar photovoltaic installations. Connecting the. power of the sun
DC disconnects for solar photovoltaic installations Connecting the power of the sun Solar energy is heating up Interest in renewable energy sources has never been greater, and the fastest growing of these
More informationDirectory chapter 02 - DIN Power (to 6 A) Types D, E, F, FM, 2F, F9, interface connectors I/U 02. 01. Technical characteristics types D and E... 02.
Directory chapter 02 - () Types D, E, F, FM, 2F, F9, interface connectors I/U Page Technical characteristics types D and E.............................. 02.10 Type D connectors.................... 02.11
More informationCircuit Breakers. Next Generation of Protection Capabilities
Circuit Breakers Next Generation of Protection Capabilities Circuit Breaker Offering Rockwell Automation offers a full line of Allen-Bradley circuit breakers and motor protection devices to help meet many
More informationPRODUCT GUIDE. SL Medium Voltage IEC Vacuum Contactors
PRODUCT GUIDE SL Medium Voltage IEC Vacuum Contactors Table of Contents 1 Overview Introduction....................................................2 Features........................................................2
More informationmecotron Safety relay ESTOP-2 For emergency stop monitoring
E0006 000824 Safety relay E-2 For emergency stop monitoring Description The safety module E-2 for emergency stop monitoring is used for safety breaking one or more circuits and is designed to be incorporated
More informationFeed-through terminal block - SSK 110 KER-EX - 0502058
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid
More informationLCP Coordination Panel Operations & Maintenance Manual Table of Contents
LCP Coordination Panel Operations & Maintenance Manual Table of Contents 1. Overview 2. NEC Requirements Overview 3. LCP Coordination Panel Data Sheet 4. Class CC Littelfuse CCMR Current-Limiting Fuse
More informationSPEEDFAX TM 2011 Disconnect Switches Contents
SPEEDFAX TM 2011 Disconnect es Contents Compact Non-Fusible es Rotary and Toggle Selection 5-2 5-4 Dimensions and Wire Ranges 5-5 Type VBII (30-600A) Features and Ordering Information 5-6 and Handle Selection
More informationSolid Core and Split Core Adjustable Current Status Switches CSS-O, CSS-C; CSP-O, CSP-C
Solid Core and Split Core Adjustable Current Status Switches CSS-O, CSS-C; CSP-O, CSP-C DESCRIPTION FEATURES PRODUCT DATA Very low operating trip points LED status indication Integral DIN rail mounting
More informationProduct and Applications Description. Application Programs. Example of Operation. GAMMA instabus Technical Product-Information.
Product and Applications Description The power supply units N 125/x2 can supply DC 24 V power from an additional pair of terminals (yellowwhite). This DC 24 V output voltage can be used to power e.g. an
More informationMagnetic and Hydraulic-Magnetic Circuit Breaker 8340-G2...
Magnetic and Hydraulic-Magnetic Circuit Breaker 840-G2... Description Single, two and three pole magnetic circuit breakers with trip-free mechanism and push/pull on/off manual actuation. A choice of fast
More informationCircuit Breakers. NRC Series. NRC Series. 900 www.idec.com
Switches & Pilot Lights Display Lights NRC series circuit breakers offer circuit protection which is far superior to using fuses in applications containing relay circuits, motor circuits, heater circuits,
More informationABB 1 NEW. Three-phase monitoring relay for grid feeding CM-UFS.1. Data sheet. Features. Approvals. Marks. Order data. Order data - Accessories
2CDC 251 014 F0t09 Features Monitoring of three-phase mains for grid feeding Type-tested in accordance with DIN V VDE V 0126-1-1: February 2006 Neutral conductor connection configurable Can also be used
More informationSEZ220. Signal Converter. Synco 200. With preprogrammed standard applications Freely programmable Menu-driven operation. Use
s 5 146 Synco 200 Signal Converter SEZ220 With preprogrammed standard applications Freely programmable enu-driven operation Use The signal converter is for use in HVAC plant to provide minimum / maximum
More informationBimetallic Overload Relay Specifications
Technical Data Bimetallic Overload Relay Specifications Bulletin Number 193K, 193T1 Topic Page Product Overview 2 Standards compliance and Certifications 2 General Specifications 193K 3 Approximate Dimensions
More informationZS4-S-T Screw Clamp Terminal Blocks Disconnect with blade - with test socket
Technical Datasheet SNK64D00 Catalogue Page SNK64S00 ZS4-S-T Screw Clamp Terminal Blocks Disconnect with blade - with test socket - Ease your test operations with the built-in test sockets, - Screwdriver
More informationTerminals, W-Series. Contents. Terminals, W-Series. Terminals, W-Series. Terminals, TS 15. Stud terminals. Accessories. Terminals, SAK-Series E.
Contents Overview W-Series.2 Feed-through terminals.4 Double level terminals.14 Modular P terminals.19 Modular disconnect terminals.29 Fuse terminals.5 Installation terminals.40 Disconnect test terminals.4
More informationPower Supply Unit, Primary Switched, Narrow Design MINI-PS-12-24DC/24DC/1
Power Supply Unit, Primary Switched, Narrow Design MINI POWER provides: Extra narrow design with widths of 22.5 mm, 45 mm, and 67.5 mm (0.886, 1.772, and 2.657 in.) Global use due to a wide-range input
More informationBlock width on rail (mm) Standard block* is shown on blue background
How To Read Terminal Block Specifications How To Read Carton Labels Rated wire size (mm ) Mounting on multiple rail Spacing on rail Spacing 6 mm + 0,05 (.3") M /6 Block width on rail (mm) Standard block*
More informationZS4-SF1-T Screw Clamp Terminal Blocks For 5 x 20 and 5 x 25 fuses - with test socket
Technical Datasheet SNK636D00 Catalogue Page SNK636S00 ZS-SF-T Screw Clamp Terminal Blocks For x 0 and x fuses - with test socket - Protect your circuit with x and x0 fuse terminal blocks (fuse not supplied
More informationCo-location Interconnect Power Panel (CIPP) Installation Guide
Co-location Interconnect Power Panel (CIPP) Installation Guide Document INS-97xxxxxxx This guide covers the following part numbers- Trimm 97xxxxxxx Series Table of Contents Section 1 - General Information...
More informationgesis IP + Heavy Duty Class I, Zone 2
gesis IP + Heavy Duty gesis IP+ 20i HD Z2 Heavy-Duty Connectors for Class 1, Zone 2 Hazardous Locations Catalog 2012 Catch the Next Wave in Modular Connections Plug & Go Heavy-Duty Connectors for areas
More informationV REG.-Nr. 115719, Z E135149 Technical data 2-pole 4-pole Rated current 12 A 6 A SCHRACK. Accessories Miniature Relay PT. General Purpose Relays
Accessories Miniature Relay PT Easy replacement of relays on a densely packed DIN rail No reduction of protection class or creepage/clearance with plastic retainer Plug-in indicator- and protection modules
More information5.2. Overview. The better method to install solderless compression connectors on power cable
5.2 Overview The better method to install solderless compression connectors on power cable The Thomas & Betts method of installing compression connectors on power cables is designed to provide a high degree
More informationVario-Series Accessories
Accessories and spare parts for GMW analogue panel meters and controllers Current Transformers pages 2-9 Shunt Resistors 10-11 Voltage Dividers 12 Power supply for indicator/controllers 13 Blanking Plates
More informationRelés e Contatores de Estado Sólido SIRIUS
Relés e Contatores de Estado Sólido SIRIUS Coletânea de dados técnicos ( product data sheet ) Agosto/212 SSR - 3RF21 22,5 mm Ponto Zero SSR - 3RF2 45 mm Ponto Zero SSR - 3RF22 45 mm Ponto Zero Trifásico
More informationCOAXICON Contacts. RF Coax Connectors. Product Facts
COXICON Contacts Product Facts Tyco Electronics provides a variety of contacts for coaxial connectors Contacts are available in a range of sizes that may be used with the various types of coaxial cable
More informationFeed-through terminal blocks for high-current applications
596 PHOENIX CONTACT With the feed-through terminal blocks, you can freely select the connection technology. Choose between traditional screw connection, robust bolt connection, and convenient push-in connection
More informationArbiter Systems Test Leads: Engineered for Optimum Performance and Safety
Arbiter Systems Test Leads: Engineered for Optimum Performance and Safety Arbiter Systems, Inc. test equipment offers outstanding performance, flexibility, and value. Our test leads offer nothing less.
More informationZS6-S Screw Clamp Terminal Blocks Disconnect with blade
Technical Datasheet SNK646D00 Catalogue Page SNK646S00 ZS6-S Screw Clamp Terminal Blocks Disconnect with blade - Ease your disconnect operations with the disconnect blade operated by hand or with a screwdriver,
More informationPower Supplies 3. SDN-P DIN Rail Series
SDN-P DIN Rail Series The SDN DIN Rail power supplies provide industry leading performance. Sag Immunity, transient suppression and noise tolerant, the SDN series ensures compatibility in demanding applications.
More informationMidNite Solar PV Combiners explained (MNPV)
MidNite Solar PV Combiners explained (MNPV) The MNPV6 PV combiner is designed to work with 6 150V breakers or 4 touch safe 600VDC fuse holders. Busbars for both configurations are included. Based on sales,
More informationVoltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
More informationRotary Disconnect Switch Specifications
Technical Data Rotary Disconnect Switch Specifications Bulletin Number 194R Topic Page Product Line Overview 2 General Specifications Fuse Description 12 Approximate Dimensions 14 Additional Resources
More information5SV Residual Current Protective Devices
s Siemens AG 2013 SENTRON 5SV Residual Current Protective Devices New portfolio for reliable personnel, material and fire protection Safe protection against residual currents Residual current protective
More informationAMP Standard Terminals and Splices. RoHS. Ready
AMP Standard Terminals and Splices RoHS Ready Table of Contents Product Facts Solderless terminals and splices performs up to today s standards for reliable termination in applications ranging from control
More informationThree-phase monitoring relay CM-PFE
Data sheet Three-phase monitoring relay CM-PFE The CM-PFE is a three-phase monitoring relay that monitors the phase parameter phase sequence and phase failure in three-phase mains. 2CDC 251 005 S0012 Characteristics
More informationE-STOP relays, safety gate monitors
Unit features Safety features Gertebild ][Bildunterschrift_NOT_Sch.tuer_Licht Safety relay for monitoring E-STOP pushbuttons, safety gates and light beam devices Approvals Gertemerkmale Positive-guided
More informationThe range of rail-mounted terminal blocks. for a perfect electrical installation.
The range of rail-mounted terminal blocks for a perfect electrical installation. The range of rail-mounted terminal blocks for a perfect electrical installation. The new standard for rail-mounted terminal
More informationPSC SQUARE BODY 690/700 Volt SEMICONDUCTOR PROTECTION FUSES
PSC SQUARE BOY Ferraz Shawmut 690/700V PSC fuse-links provide maximum flexibility in equipment design and ultimate protection for today s power conversion equipment. These square body fuse-links are available
More informationConnecting the Power of the Sun. DC Disconnects for Solar Photovoltaic Installations. DC disconnects for. solar photovoltaic installations
Connecting the Power of the Sun DC Disconnects for Solar Photovoltaic Installations DC disconnects for solar photovoltaic installations Solar energy is heating up Interest in renewable energy sources has
More information38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A 38 SERIES Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical
More informationRMM2 Heat-Tracing Remote Monitoring Module for the Raychem NGC Control System Installation Instructions
Heat-Tracing Remote Monitoring Module for the NGC Control System Installation Instructions Tools Required 3 mm slotted screwdriver 3/8 hex key (for -4X only) Approvals Nonhazardous locations Type NM LISTED
More informationSolar Circuit Protection Application Guide. Complete and reliable solar circuit protection
Solar Circuit Protection Application Guide Complete and reliable solar circuit protection Introduction Benefits of Eaton s Circuit Protection Solutions Complete and Reliable Circuit Protection for Photovoltaic
More informationRM4TG20 three-phase network control relay RM4-T - range 200..500 V
Characteristics three-phase network control relay RM4-T - range 200..500 V Complementary [Us] rated supply voltage Output contacts Setting accuracy of time delay Delay at power up Measuring cycle Marking
More informationVoltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
More informationZS25 Screw Clamp Terminal Blocks Feed-through
Technical Datasheet SNK668D0 Catalogue Page SNK678S0 ZS Screw Clamp Terminal Blocks Feed-through Save space by connecting conductors up to mm² AWG in just mm 0.47 in spacing. SNK68V004 SNK004F0000 D CAD
More information.093 [2.36] Commercial Pin and Socket Connectors
Product Facts Polarized Cavity identification Low contact-mating force Dual locking lances Detent and positive locking Contacts available in brass and phosphor bronze with tin and gold plating Panel mounting
More informationAmphenol C 091 A/B/D. Circular Connectors. Amphenol-Tuchel Electronics GmbH
Amphenol C 091 A/B/D Circular Connectors Amphenol-Tuchel Electronics GmbH C 091 A Main Features Metal threaded coupling acc. to IEC. Number of contacts are 2 to 8, 12 and 14. Internal metal strain relief
More informationSENTRON Switching and Protection Devices Air Circuit Breakers
Siemens AG 9 SENTRON Switching and rotection Devices Air Circuit reakers 5 5/ Introduction 3WL Air Circuit reakers 3WL Air Circuit reakers/ Non-Automatic Air Circuit reakers up to 63 A (AC) 5/6 General
More informationDecision-Maker Paralleling System. Power Distribution Switchboards and Circuit Breakers. Standard Features
Decision-Maker Paralleling System Power Distribution Switchboards and Circuit Breakers Power Distribution Switchboards and Circuit Breakers The generator paralleling circuit breakers for the Kohler Decision-Maker
More informationBulletin 1489 Circuit Breakers. Selection Guide
Bulletin 1489 s Selection Guide Bulletin 1489-A Overview/Description Bulletin 1489-A s Energy-limiting design protects downstream components better than conventional breakers during short circuits Field-mountable
More informationDirectory chapter 04
M Directory chapter 04 D-Sub Mixed subminiature D connectors New Page D-Sub mixed connector system general information................... 04.02 Contact arrangements............................................
More informationDescription. Dimensions. Features. www.pwb-encoders.com. precision works better
Description The MEC22 is a high resolution optical hollow shaft encoder that can be fixed quickly and easily on different sizes of motor shafts. The encoder provides two square wave outputs in quadrature
More information48 SERIES Relay interface modules 10 A
48 Relay interface modules 10 A 1 CO relay interface modules, mm wide Ideal interface for PLC and electronic systems Type 48.P3 1 CO 10 A s Type 48.31 1 CO 10 A s AC coils or DC sensitive coils Supply
More informationCatalog January. Heavy industrial power applications Motor contactors and starters
Catalog January Heavy industrial power applications Motor contactors and starters 2006 General contents 0 Heavy Industrial Power Applications Motor Contactors and Starters 1 Contactors and Starters, Type
More informationMiniature Circuit Breakers and Supplementary Protectors
Miniature Circuit Breakers and Supplementary Protectors Miniature Circuit Breakers and Supplementary Protectors. Industrial Circuit Breakers QUICKLAG............................................. QUICKLAG
More information