Fire/Alarm/Security/Communications Product Catalog

Transcription

1 Surge Protection For Business-Critical Continuity TM Fire/Alarm/Security/Communications Product Catalog FPO

2 Protection Against Damage, Disruption, and Costly Downtime of your Mission-Critical Equipment Today s advanced commercial/residential fire, alarm, security and telecommunication systems are more sophisticated than ever before. In a nanosecond, transients can disrupt, disable and ruin your mission-critical equipment. It s why companies turn to Emerson Network Power Surge Protection for their line of surge suppression and filtering products to protect sensitive equipment from excessive maintenance costs, damage and costly downtime. Emerson Network Power s comprehensive portfolio includes products for Data/Signal Line Protection, AC Power Surge Protection, and Filtering/Line Conditioning. Plus, all of our engineered power-quality solutions are backed by a dedicated team of power-quality specialists who are available to share their applications and integration knowledge with you. We re here to help! Why take chances by putting the security of your mission-critical equipment at risk? Turn to Emerson Network Power Surge Protection products for peace of mind. To learn more about the world s most trusted lineup of multi stage, hybrid, solid state, power quality products, call us toll-free at , or visit our Web site at

3 Table of Contents Application Product Page # CCTV Systems Application Drawing 2 Zone/Loop/Data Edco PC642 Series VAC Heavy Duty 120 Volt AC Edco HSP Series 4 Plug-in Surge Protection/Active Tracking Filter Islatrol SP-6TVN 5 CCTV & Data Applications/Coax Edco CX Series 6 Closed Circuit TV Protection Edco CCTV-1 7 One- and Two-Pair Signal Line Protection Edco FAS-1 and FAS-2 Series 7 Two-Pair Signaling Circuit Protector (Modular) Edco PHC Series 8 CAT6/CAT5 Power Over Ethernet Edco CAT6-5POE Series 9 Channel Rackmount Edco RM-CX06-16R 9 Fire Alarm Application Drawing 10 Zone/Loop/Data Edco PC642 Series 11 Two-Pair SLC Loop Protector (Modular) Edco SLCP Series 12 Two-Line Telephone Protection (Modular) Edco PC2-TEL 12 Two-Pair Signaling Circuit Protector (Modular) Edco PHC Series VAC Heavy Duty 120 Volt AC Edco HSP Series /240 VAC Heavy Duty (Parallel) PowerSure EMC-240B 15 One- and Two-Pair Signal Line Protection Edco FAS-1 and FAS-2 Series 16 Medium Duty 120 VAC Single Phase PowerSure FAS-120AC 17 Burglar 12VDC Application Drawings 18 One- and Two-Pair Signal Line Protection Edco FAS-1 and FAS-2 Series 19 Plug-in Surge Protection (Active Tracking Filter) Islatrol SP-6TVN 20 RJ11/RJ31X Telephone Protection Edco FAS-TEL and FAS-31XT 21 Single-Pair Medium Duty Low Voltage Zone/Horn/Strobe/Data Edco TER Series 22 Two-Line Telephone Protection (Modular) Edco PC2-TEL 22 ACCESS CONTROL Application Drawing 23 Electric Door Suppressor Edco EL-EDS 24 Two-Pair Data/Signal Line Power Edco 5W RJ11/RJ31X Telephone Protection Edco FAS-TEL and FAS-31XT VAC Heavy Duty 120 Volt AC Edco HSP Series 27 Zone/Loop/Data Edco PC642 Series 28 Data Circuit Protection Edco LCDP 29 COMMUNICATIONS One- and Two-Pair Signal Line Protection Edco FAS-1 and FAS-2 Series 30 DIN Rail Protection Edco DRS (DC) Series 31 High Frequency Coax Protector N-Type Edco CX-HFN 32 High Frequency Coax Protector F-Type Edco CATV-DF 32 Intercom/Speaker Punch Block Protection (Parallel) Edco OPX Series 33 Intercom/Speaker Punch Block Protection (Series) Edco PB Series 34 Telecom/Punch Block Protection Edco H Series 35 Data/Signal Line/Punch Block Protection Edco COHP Series 36 Fits Standard 66MI-50 Punch Down Blocks Edco MGB Ground Rail 36 RJ11/RJ31X Telephone Protection Edco FAS-TEL and FAS-31XT 37 Multi-Channel Rackmount Edco RM-CAT6-POE Series 38 Data Circuit Protection Edco LCDP 38 RJ-45 Telephone/Data Edco RJA-RJD Series 39 Terminating Assembly Edco TBLK Assembly 40 CAT6/CAT5 Power Over Ethernet Edco CAT6-5POE Series 40 Key Systems Edco Mod-12 41

4 CCTV Systems Protecting CCTV Systems Application Drawing Video Head-End SP 3 SP 5 Video Power SP 4 SP 5 Exterior Fixed Camera Equipment Rack Multiplexer SP 3 SP 5 SP 6 SP 7 Video Power RS-485, RS-422 (PTZ) Power Over Ethernet (POE) SP 4 SP 5 SP 6 SP 7 Exterior Camera with PTZ AC Power SP 1 or SP 2 Exterior POE Camera For POE with PTZ contact Edco Legend SP 1... HSP121BT-1RU SP 2... SP-6TVN SP 3... CX06-M or... RM-CX06-16R (16 ch.) SP 4... CX06-MI SP 5... FAS-1-043HC (2.5A) or... PHC-043* (5A) SP 6... PC642C-008LC* SP 7... CAT6-5 POE-FF or -MF *Needs PCB1B Base 2

5 CCTV Systems Edco PC642 Series Zone/Loop/Data The Edco PC642 Series surge suppressor is a two-pair (four-wire) module implementing three-stage hybrid technology. This module addresses over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak and fault currents are mitigated with resettable fuses (PTCs). The PTCs increase resistance by several orders of magnitude when over-currents exceed safe levels. A normal state resumes when over-currents are removed. The ability to self-restore in this manner significantly increases suppressor performance and survivability. EDCO PCB1B BASE SOLD SEPARATELY OPTION: DIN RAIL KIT AVAILABLE ORDER PART # 11604KIT-PC The Edco PC642 Series card edge module is gold plated, double sided, and is designed to mate with the Edco PCB1B gold-plated female terminal connector. When snapped together, the data circuits pass thru the protector in a serial fashion from the four Field Side terminals to the four Electronics Side terminals. Terminals 1 or 10 of the Edco PCB1B must be attached to Building- Approved Ground per Edco Technical Bulletin # Three-stage hybrid protection Sneak/fault current protection Resettable fusing PTCs Low capacitance option Plug-in module Fast response time Requires Edco PCB1B base Order PC642PTU an invaluable troubleshooting tool 5, 12, 18, 24, 30, 36, 43, 52, 180 VDC 8, 15, 20, 30, 36, 43, 50, 60, 200* VDC Operating Current 0.15A 10 ka (8 x 20 µs) 0 to 20 MHz < 0.1 db at 20 MHz GDT, SAD, w/series PTC Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 2H x 1W x 2.5L (PC642 + PCB1B Base) Certification 1 oz UL 497B * PC642C-200 is not UL certified Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continuously supplying more than 150 milliamperes. Terminal Assignments Unprotected Pair 2 Field Side Unprotected Pair 1 Odd Terminals { { PCB1B: 1.0 Even Terminals } Protected Pair 2 Electronics Side 2.125" 2.4" 2 } Protected Pair 1 Keying Pin Ground Terminal 1 Or 10 To Building-Approved Ground DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. PC642 PCB1B APPLICATION: RS485, RS422: PC642C-008LC & PCB1B RS423, Token Ring: PC642C-008LC & PCB1B RS232: E-Net, 10 Base T: PC642C-020 & PCB1B PC642C-030LC & PCB1B 4 20 ma: PC642C-036 & PCB1B How To Specify The Appropriate Model PC642C - Voltage Clamp 8 Volts Volts Volts Volts Volts Volts Volts Volts **200 Volts **Not UL Listed no suffix stage 2 clamp each line-to-ground stage 2 clamp D line-to-line only stage 2 clamp line-to-line X and each line to ground low capacitance option stage LC 2 clamp line-to-line and each line to ground 3

6 CCTV Systems edco hsp121bt-1ru Edco HSP Series 120 VAC Heavy Duty 120 Volt AC The Edco HSP Series is an advanced three-stage hybrid, solid state powerline protector. such as noise filtering, common mode and normal mode suppression, nanosecond reaction time, power line tracking, and compression screw terminations make the Edco HSP Series an excellent choice in commercial and industrial applications. The Edco HSP Series offers a replaceable fuse designed to remove the load (protected equipment) from the line if the unit is either overloaded or the internal protection fails. This feature prevents surges from entering equipment through a failed protector not noticed by the user. edco hsp121a Fast response time Failure indicator Power line tracking Filtering Polycarbonite NEMA 4X enclosure (HSP121A) Three-stage hybrid design Replaceable fuse 1/2" or 3/4" knockouts for nipple conduit connectors (HSP121A) Dimensions Operating Current I-Nominal (In) Total Operating Frequency EMI Attenuation (100 khz to 100 MHz) Modes Of Protection Status Indication 120 VAC 325 VAC 15A 3 ka 39 ka (8 x 20 µs) Hz > 40 db Metal Oxide Varistors (MOVs) w/ L-C Filter Line-to-Neutral, Line-to-Ground, Neutral-to-Ground Power On & MOVs functional 3 Position, 20A Terminal Block w/compression Screws Terminals Accept Up To 14 AWG Dimensions (Inches) HSP121BT-1RU 1.8H x 2.9W x 5.3L HSP-121A 2.95H x 4.95W x 3L 10 oz Certifications HSP121BT-1RU ANSI/UL1449 Third Edition, Type 4 HSP121A ANSI/UL1449 Third Edition, Type 2 Mounting HSP121BT-1RU Holes 3/16" Dia. Light On Normal Light Off Requires Service Mounting HSP121A Holes 3/16" Dia. 3/4" Conduit Fitting 3/4" Conduit Fitting GND 1/2" Conduit Fitting N N 1/2" Conduit Fitting AC GND AC 4

7 CCTV Systems Islatrol SP-6TVN Plug-in Surge Protection/Active Tracking Filter The Islatrol SP-6TVN is an industrial-strength surge suppression/filtering device that plugs into a standard duplex receptacle. It features uniquely designed repositionable outlets and protects against damaging power disturbances traveling through your wiring into your electrical outlets. REPOSITIONABLE OUTLETS Plugs into standard 120V, 15A electrical outlet Total peak surge current capacity of 39 ka Cables for telephone, video, and data connectors included Repositionable outlets rotate to accommodate available space Perfect for tight spaces, behind furniture and appliances Intelligent monitoring against improper wiring/grounding 60 db maximum high frequency Operational indicator lamp AC Power Protection Nominal Operating Voltage 120 VAC, Single Phase Operating Voltage Range 120 VAC +/- 10% Operating Hz Rated Output 15A ANSI/IEEE C62.41 Category Category A & B (6) 5-15R Receptacles and 5-15P Plug Phase Configuration 2 Wire + Gnd Size 7.5 x 4.75 x 1.75 (Inches) Enclosure High Impact Plastic 2.0 lbs (0.9 kgs) Modes Of Protection L N, L G, N G Indication of Suppression Status Status Indicator Response Time <.5 ns Normal Mode Certification ANSI/UL 1449 Third Edition Type 3 Warranty 5 Year Maximum Continuous Operating Voltage (MCOV) Line To Neutral (8 x 20 ms) Line To Neutral Line To Ground Neutral To Ground Total 130 VAC 13 ka 13 ka 13 ka 39 ka ANSI/IEEE C62.41 Cat A Ringwave (6 kv, 200A, 100 khz) Normal Mode Common Mode ANSI/IEEE C62.41 Cat B Ringwave (6 kv, 500A, 100 khz) Normal Mode Common Mode Frequency Response Normal Mode Common Mode Low Voltage Protection 265V 290V 275V 290V 60 db Maximum, Forward/Reverse, 100 khz to 50 MHz 40 db Maximum, Forward/Reverse, 5 MHz to 50 MHz Video 1 & 2 Phone Network Type F Type RJ-11 Type RJ-45 Cables Provided 6 (2x) Type F RJ-11 Male RJ-45 Male 6' Ends 6' Ends Ends 5 ka 2 ka 3 ka (8 x 20 µs) (10 x 1000 µs) (8 x 20 µs) Capacitance <12 pf <50 pf <70 pf Protection Level L-G T-R, T-G, R-G L-G (8 Lines) (DC) 145 V V 30 V Attenuation 1 2 Ghz N/A N/A 5

8 CCTV Systems Edco CX Series CCTV & Data Applications/Coax OPTION: DIN RAIL KIT AVAILABLE ORDER PART # 11604KIT-CX The Edco CX Series Surge Protective Devices (SPDs) implement three-stage hybrid technology. The SPDs address over-voltage transients with a primary Gas Discharge Tube (GDT), and secondary Silicon Avalanche Diode (SAD) components. Over-current protection, e.g. sneak and fault currents, are mitigated with solid-state resettable fuses PTCs. The Edco CX Series SPDs are designed in accordance with NFPA 780 (2004 edition) requirements, with up to 20 ka of surge current capability. The Edco CX06-MI model has an isolated ground and is recommended for use at the camera end. Sneak/fault current protection Low insertion loss Shielded case CX06-MI has an isolated ground 5 VDC 6 VDC Operating Current 0.17A 20 ka (8 x 20 µs) 0 to 20 MHz < 1 db at 20 MHz GDT, SAD, w/series PTC BNC, 50/75 Ohms Dimensions (Inches) M = 1.5H x 1W x 3.25L MI = 1.5H x 1W x 4L SBL = 1.7H x 1.4W x 2.8L M = 2.3 oz MI = 3 oz Certification UL 497B CX06-MI-SBL Installation Head End Camera End CX06-M CX06-MI CX06-MI-SBL Other configurations available please consult factory 6

9 CCTV Systems Edco CCTV-1 Closed Circuit TV Protection The Edco CCTV-1 application is specifically designed for lightning protection on closed circuit TV systems. The protector is easily installed with standard type BNC coax connectors. The Edco CCTV-1 offers low loss, even at frequencies approaching 500 Mhz. This is important for error-free data communication applications. Automatic recovery Shielded case Low insertion loss Miniature size Easily installed 5 VDC 90 VDC (Spark Over Voltage) Operating Current 1A 10 ka (8 x 20 µs) 0 to 1 GHz < 0.5 db at 500 MHz <1.0 db at 900 MHz Gas Discharge Tube (GDT) BNC, 75 Ohm Dimensions (Inches) 0.6H x 0.6W x 2.0L 1 oz Edco FAS-1 and FAS-2 Series One- and Two-Pair Signal Line Protection The Edco FAS-1 and Edco FAS-2 Series are multi-stage one-pair or two-pair surge suppressors designed for high-exposure applications. These products were specifically designed to meet multiple, low voltage, protection applications in the fire and security industries. Lightning protection for low voltage Data/signal lines Multi stage protection Common mode and differential protection mode Automatic recovery 15, 24, 36, 52 VDC 18, 33, 43, 60 VDC Operating Current 2.5A 10 ka (8 x 20 µs) 0 to 10 MHz < 0.1 db at 10 MHz GDT, SAD, w/series Inductor Terminal Block w/compression Lugs Terminals Accept Up To 12 AWG Dimensions (Inches) FAS-1 = 1.5H x 1.5W x 2.8L FAS-2 = 2H x 2W x 2.8L FAS-1 = 3.5 oz FAS-2 = 7 oz Certification UL 497B Installation Unprotected Or Field Side Ground Lug AWG Equip. Line Protected Equipment DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair)* FAS HC (Two-pair)* *Not UL listed 12 VDC Use 24 VDC Use 24 VAC Use 48V Systems Use Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continuously supplying more than 2.5 amperes. 7

10 CCTV Systems Edco PHC Series Two-Pair Signaling Circuit Protector (Modular) The Edco PHC Series is designed to protect two pairs of wires specifically for alarm and security systems where operating currents can be as high as 5 amps. Electrically, the Edco PHC Series is a rugged series hybrid implementing a staged complement of MOVs, copper wound inductors and Silicon Avalanche Diodes. This design reduces series resistance to 0.2 Ohms per pair. These products are intended to mate with an Edco PCB1B gold-plated female terminal connector. EDCO PCB1B BASE SOLD SEPARATELY EDCO PCB1B BASE SOLD SEPARATELY The Edco PHC modules plug into a base assembly (Edco PCB1B). The base assembly can be mounted to any flat surface and should be located as close as practical to the protected equipment. Terminal 1 and/or terminal 10 should be connected to Building-Approved Ground with 12- or 10-gauge solid wire. Three-stage protection Differential protection Common mode protection Plug-in module Automatic recovery Fast response time Continuous current up to 5 Amps UL 497B listed Requires Edco PCB1B base Order PC642PTU an invaluable troubleshooting tool 12, 18, 24, 36, 52, 70, 120 VDC Operating Current 15, 20, 30, 43, 60, 100, 150 VDC 5A 10 ka (8 x 20 µs) 0 to 10 MHz < 0.1 db at 10 MHz MOV, SAD, w/series Inductor Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 3.7H x 1.75W x 2.375L (PHC + PCB1B Base) Certification 8 oz UL 497B Terminal Assignments Unprotected Pair 2 Field Side Unprotected Pair 1 Odd Terminals { { PCB1B: 1.0 Even Terminals } Protected Pair 2 Electronics Side 2.125" 2.4" 2 } Protected Pair 1 Keying Pin Ground Terminal 1 Or 10 To Building-Approved Ground DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. Dimensions How To Specify The Appropriate Model Voltage Clamp * Not UL listed Applications Part Number 24V Horn, Strobe, Bell 70V Speaker Lines PHC-043 & PCB1B PHC-SP70 & PCB1B 8

11 CCTV Systems Edco CAT6-5POE Series CAT6/CAT5 Power Over Ethernet The Edco CAT6-5POE Series is designed to work on Category 5 Power-Over- Ethernet transmission lines as well as Category 6 applications. Ideal to protect expensive equipment against surges and transients entering a building on exposed transmission lines. Available in both female to female and male to female RJ-45 connectors. Exceeds CAT5 & 6 transmission values CAT5 POE compatible CAT6 compatible Applications up to ma 1 year warranty 60 VDC RJ-45 Jacks RJ-45 (Female-Female) CAT6-5POE-FF 65 VDC RJ-45 (Male-Female) CAT6-5POE-MF Operating Current 300 ma 60A (10 x 1000 µs) 0 to 250 MHz Dimensions (Inches) 0.8H x 1.0W x 2.3L (FF). 0.8H x 1.0W x 3.0L (MF) 1 oz < 0.1 db at 20 MHz Silicon Avalanche Diode (SAD) Edco RM-CX06-16R Channel Rackmount The Edco RM-CX06-16R Surge Protective Device (SPD) is a 16 channel coax SPD implementing three-stage hybrid technology. The SPD addresses over-voltage transients with a primary Gas Discharge Tube (GDT), and secondary Silicon Avalanche Diode (SAD) components. Over-current protection, e.g., sneak and fault currents, are mitigated with new solid-state resettable fuses PTCs. The Edco RM-CX06-16R SPD is designed in accordance with NFPA 780 (2004 edition) requirements, with up to 20 ka of surge current capability. Sneak/fault current protection Low insertion loss Shielded case 16 channel 1 year warranty 5 VDC 0 to 100 MHz 6 VDC < 0.1 db at 20 MHz Dimensions (Inches) 1.75H x 19W x 2.0D (1U) Operating Current 0.15A GDT, SAD, w/series PTC 3.2 lbs 20 ka (8 x 20 µs) BNC, 50/75 Ohm Certification UL 497B 9

12 Fire Alarm Protecting Fire Alarm Systems Application Drawing SP 4 SLC Loop Penetrating Exterior SP 4 Fire Alarm Panel (24 VDC Typical) SP 5 SP 6 SP 7 RS-485 Network Exterior Post Indicator Valve Circuit Exterior (Over 1000 feet need protection at wall penetration point) Notification Appliance Circuit Exterior SP 6 SP 5 SP 7 SP 8 Printer Circuit To Guard House (RS-232 Typical) SP 8 AC Power SP 1 or SP 2 or SP 9 Telephone Line SP 3 SP 1... FAS-120AC SP 2... HSP-121BT1RU SP 3... PC2-TEL* SP 4... SLCP-43* SP 5... PC642C-008LC* Legend SP 6... FAS-1-033HC SP 7... PHC-043* SP 8... PC642C-020* SP 9... EMC-240B *Needs PCB1B Base 10

13 Fire Alarm Edco PC642 Series Zone/Loop/Data The Edco PC642 Series surge suppressor is a two-pair (four-wire) module implementing three-stage hybrid technology. This module addresses over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak and fault currents are mitigated with resettable fuses (PTCs). The PTCs increase resistance by several orders of magnitude when over-currents exceed safe levels. A normal state resumes when over-currents are removed. The ability to self-restore in this manner significantly increases suppressor performance and survivability. EDCO PCB1B BASE SOLD SEPARATELY OPTION DIN RAIL KIT AVAILABLE ORDER PART # 11604KIT-PC The Edco PC642 card edge module is gold plated, double sided, and is designed to mate with the Edco PCB1B gold-plated female terminal connector. When snapped together, the data circuits pass thru the protector in a serial fashion from the four Field Side terminals to the four Electronics Side terminals. Terminals 1 or 10 of the Edco PCB1B must be attached to Building-Approved Ground per Edco Technical Bulletin # Three-stage hybrid protection Sneak/fault current protection Resettable fusing PTCs Low capacitance option Plug-in module Fast response time Requires Edco PCB1B base Order PC642PTU an invaluable troubleshooting tool 5, 12, 18, 24, 30, 36, 43, 52, 180 VDC 8, 15, 20, 30, 36, 43, 50, 60, 200* VDC Operating Current 0.15A 10 ka (8 x 20 µs) 0 to 20 MHz < 0.1 db at 20 MHz GDT, SAD, w/series PTC Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 2H x 1W x 2.5L (PC642 + PCB1B Base) Certification 1 oz UL 497B * PC642C-200 is not UL certified Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continuously supplying more than 150 milliamperes. Terminal Assignments Ground Terminal 1 Or 10 To Building-Approved Ground DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. APPLICATION: RS485, RS422: PC642C-008LC & PCB1B RS423, Token Ring: PC642C-008LC & PCB1B RS232: E-Net, 10 Base T: PC642C-020 & PCB1B PC642C-030LC & PCB1B 4 20 ma: PC642C-036 & PCB1B How To Specify The Appropriate Model Voltage Clamp **200 Volts **Not UL Listed 11

14 Fire Alarm Edco SLCP Series Two-Pair SLC Loop Protector (Modular) The Edco SLCP Series are four-wire modules designed to protect signaling line circuits (SLC). The device has 0 ohms of resistance and offers line-toground protection. EDCO PCB1B BASE SOLD SEPARATELY Compatible with SLC circuits Line-to-ground protection State-of-the-art silicon technology Over-current protection 497B UL listed Requires Edco PCB1B base PC642PTU (Pass Thru Unit) available for troubleshooting 5, 12, 18, 24, 32, 36, 48, & 52 VDC 8, 15, 20, 30, 36, 43, 50, & 60 VDC Operating Current 1A 250A (8 x 20 µs) 0 to 20 MHz < 0.1 db at 20 MHz Silicon Avalanche Diode (SAD) Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 2H x 1W x 2.5L (SLCP + PCB1B Base) Certification 1 oz UL 497B S L C P Clamping Voltage 8 Volts 15 Volts 20 Volts 30 Volts 36 Volts 43 Volts 50 Volts 60 Volts Edco PC2-TEL Two-Line Telephone Protection (Modular) The Edco PC2-TEL is a solid state, two-line telephone interface protector module. This unit is specifically designed to protect both phone lines required by commercial fire panels. EDCO PCB1B BASE SOLD SEPARATELY Tip-to-ring protection Tip- and ring-to-ground protection Over-current protection Resettable solid state fuses PTC UL listed 497A Requires PCB1B base PC642PTU (Pass Thru Unit) available for trouble shooting 250 VDC 270 VDC Operating Current 0.15A 160A (10 x 1000 T & R To Ground) 0 to 20 MHz < 0.1 db at 20 MHz Series PTC and Silicon Avalanche Diode (SAD) Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 2H x 1W x 2.5L (PC2TEL + PCB1B Base) Certifications 1 oz UL 497A, CUL 12

15 Fire Alarm Edco PHC Series Two-Pair Signaling Circuit Protector (Modular) The Edco PHC Series is designed to protect two pairs of wires specifically for alarm and security systems where operating currents can be as high as 5 amps. Electrically, the Edco PHC Series is a rugged series hybrid implementing a staged complement of MOVs, copper wound inductors and Silicon Avalanche Diodes. This design reduces series resistance to 0.2 Ohms per pair. These products are intended to mate with an Edco PCB1B gold-plated female terminal connector. EDCO PCB1B BASE SOLD SEPARATELY The Edco PHC modules plug into a base assembly (Edco PCB1B). The base assembly can be mounted to any flat surface and should be located as close as practical to the protected equipment. Terminal 1 and/or terminal 10 should be connected to Building-Approved Ground with 12- or 10-gauge solid wire. Three-stage protection Differential protection Common mode protection Plug-in module Automatic recovery Fast response time Continuous current up to 5 Amps UL 497B listed Requires Edco PCB1B base Order PC642PTU an invaluable troubleshooting tool 12, 18, 24, 36, 52, 70, 120 VDC Operating Current 15, 20, 30, 43, 60, 100, 150 VDC 5A 10 ka (8 x 20 µs) 0 to 10 MHz < 0.1 db at 10 MHz MOV, SAD, w/series Inductor Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 3.7H x 1.75W x 2.375L (PHC + PCB1B Base) Certification Applications Part Number 8 oz UL 497B Terminal Assignments Unprotected Pair 2 Field Side Unprotected Pair 1 Odd Terminals { { PCB1B: 1.0 Even Terminals } Protected Pair 2 Electronics Side 2.125" 2.4" 2 } Protected Pair 1 Keying Pin Ground Terminal 1 Or 10 To Building-Approved Ground DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. Dimensions How To Specify The Appropriate Model Voltage Clamp P H C Volts Volts Volts Volts Volts (For Horn, Bell, Strobes) S P 7 0 *100 Volts R M S *150 Volts (For 120V Signal Lines) *Not UL Listed 24V Horn, Strobe, Bell 70V Speaker Lines PHC-043 & PCB1B PHC-SP70 & PCB1B 13

16 Fire Alarm edco hsp121bt-1ru Edco HSP Series 120 VAC Heavy Duty 120 Volt AC The Edco HSP Series is an advanced three-stage hybrid, solid state power- line protector. such as noise filtering, common mode and normal mode suppression, nanosecond reaction time, power line tracking, and compression screw terminations make the Edco HSP Series an excellent choice in commercial and industrial applications. The Edco HSP Series offers a replaceable fuse designed to remove the load (protected equipment) from the line if the unit is either overloaded or the internal protection fails. This feature prevents surges from entering equipment through a failed protector not noticed by the user. edco hsp121a Fast response time Failure indicator Power line tracking Filtering Polycarbonite NEMA 4X enclosure (HSP121A) Three-stage hybrid design Replaceable fuse 1/2" or 3/4" knockouts for nipple conduit connectors (HSP121A) Dimensions Operating Current I-Nominal (In) Total Operating Frequency EMI Attenuation (100 khz to 100 MHz) Modes Of Protection Status Indication 120 VAC 325 VAC 15A 3 ka 39 ka (8 x 20 µs) Hz > 40 db Metal Oxide Varistors (MOVs) w/ L-C Filter Line-to-Neutral, Line-to-Ground, Neutral-to-Ground Power On & MOVs functional 3 Position, 20A Terminal Block w/compression Screws Terminals Accept Up To 14 AWG Dimensions (Inches) HSP121BT-1RU 1.8H x 2.9W x 5.3L HSP-121A 2.95H x 4.95W x 3L 10 oz Certifications HSP121BT-1RU ANSI/UL1449 Third Edition, Type 4 HSP121A ANSI/UL1449 Third Edition, Type 2 Mounting HSP121BT-1RU Holes 3/16" Dia. Light On Normal Light Off Requires Service Mounting HSP121A Holes 3/16" Dia. 3/4" Conduit Fitting 3/4" Conduit Fitting GND 1/2" Conduit Fitting N N 1/2" Conduit Fitting AC GND AC 14

17 Fire Alarm PowerSure EMC-240B 120/240 VAC Heavy Duty (Parallel) The PowerSure EMC-240B surge suppressor is designed to protect AC distribution panel circuits or 120V power supplies feeding sensitive electronic equipment. Electrically, the unit incorporates MOV and thermal fusing technology. The PowerSure EMC-240B is designed to be installed in parallel on standard single phase 120/240 VAC (3W + G) or single phase 120 VAC (2W + G) circuits. Fast response time 40 ka per phase capacity Failsafe and fused Operational status indicators ANSI/UL 1449 Third Edition Type 2 120/240 VAC I Nominal (In) 3 ka Operating Current NA, Parallel Total 80 ka (8 x 20 µs) Operating Frequency Hz EMI Attenuation (100 khz to 100 MHz) > 40 db Metal Oxide Varistors (MOVs) Modes Of Protection Line-to-Line Line-to-Neutral Status Indication Power On & MOVs Functional Wire Leads Dimensions (Inches) 4.6H x 2.2W x 2.8L 13.5 oz Certification ANSI/UL 1449 Third Edition, Type 2 Mechanical 4.5" 2.8" 2.2" 18" Caution: Installation and service should be performed by qualified electricians only. Before installing EMC, remove all electrical power from circuits. Connect on load side of main breakers. Use two dedicated 30A circuit breakers. Installation 120 VAC Service 120/240 VAC Service 240 V AC Service L N 120 V EMC-240B L1 240 V L2 N 120 V 120 V EMC-240B L1 240 V L2 GND 240 V 240 V EMC-240B Ground N L Black Black White Green Ground L2 N L1 Black Black White Green L2 GND L1 Black Black White Green

18 Fire Alarm Edco FAS-1 and FAS-2 Series One- and Two-Pair Signal Line Protection The Edco FAS-1 and Edco FAS-2 Series are multi stage one-pair or two-pair surge suppressors designed for high exposure applications. These products were specifically designed to meet multiple low voltage protection applications in the fire and security industries. Lightning protection for low voltage Data/signal lines Multi stage protection Common mode and differential protection mode Automatic recovery 15, 24, 36, 52 VDC 18, 33, 43, 60 VDC Operating Current 2.5A 10 ka (8 x 20 µs) 0 to 10 MHz < 0.1 db at 10 MHz GDT, SAD, w/series Inductor Terminal Block w/compression Lugs Terminals Accept Up To 12 AWG Dimensions (Inches) FAS-1 = 1.5H x 1.5W x 2.8L FAS-2 = 2H x 2W x 2.8L FAS-1 = 3.5 oz FAS-2 = 7 oz Certification UL 497B Installation Unprotected Or Field Side Ground Lug AWG Equip. Line < 3 Protected Equipment FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair)* FAS HC (Two-pair)* * Not UL listed 12VDC Use 24VDC Use 24VAC Use 48V Systems Use Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continuously supplying more than 2.5 amperes. DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. 16

19 Fire Alarm PowerSure FAS-120AC Medium Duty 120 VAC Single Phase The PowerSure FAS-120AC surge suppressor is designed to protect AC distribution panel circuits or 120V power supplies feeding sensitive electronic equipment. Electrically the unit incorporates MOV and thermal fusing technology. This device is designed to be installed in parallel on standard single phase 120 VAC (L, N, G) circuits. Installation can be close-nipple up to a distribution panel/circuit or hardwired in parallel up to power supply input terminal screws. Be sure to dress leads as short as possible. LED indicator Fast response time Thermal fuse L-G, L-N, & N-G protection Compact size Liquid tight conduit fitting ANSI/UL 1449 Third Edition Type 2 Mounting Part Number PowerSure FAS-120AC 120 VAC SPD Location Type Type 2 I-Nominal (In) 3 ka Operating Current NA 6.5 ka/mode, 13 ka/phase, 15.5 ka/total Operating Frequency Hz EMI Attenuation NA MOVs Modes of Protection L-N, L-G, N-G Status Indication Power On & MOVs Functional Wire Leads Dimensions (Inches) 2.5H x 1.5W x 3.0L 4 oz Certification ANSI/UL 1449 Third Edition, Type 2 2.5" Ø " Caution: This product should be installed and serviced by qualified service technicians or personnel only. Remove power before installation or service. 3" 17

20 Burglar 12VDC Protecting Burglar Alarm Systems Application Drawings Commercial Residential 18

21 Burglar 12VDC Edco FAS-1 and FAS-2 Series One- and Two-Pair Signal Line Protection The Edco FAS-1 and Edco FAS-2 Series are multi stage one-pair or two-pair surge suppressors designed for high-exposure applications. These products were specifically designed to meet multiple, low voltage, protection applications in the fire and security industries. Lightning protection for low voltage Data/signal lines Multi stage protection Common mode and differential protection mode Automatic recovery 15, 24, 36, 52 VDC 18, 33, 43, 60 VDC Operating Current 2.5A 10 ka (8 x 20 µs) 0 to 10 MHz < 0.1 db at 10 MHz GDT, SAD, w/series Inductor Terminal Block w/compression Lugs Terminals Accept Up To 12 AWG Dimensions (Inches) FAS-1 = 1.5H x 1.5W x 2.8L FAS-2 = 2H x 2W x 2.8L FAS-1 = 3.5 oz FAS-2 = 7 oz Certification UL 497B Installation Unprotected Or Field Side Ground Lug AWG < 3 Equip. Line FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair)* FAS HC (Two-pair)* *Not UL listed 12VDC Use 24VDC Use 24VAC Use 48V Systems Use Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continuously supplying more than 2.5 amperes. Protected Equipment DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. 19

22 Burglar 12VDC Islatrol SP-6TVN Plug-in Surge Protection (Active Tracking Filter) The Islatrol SP-6TVN is an industrial-strength surge suppression/filtering device that plugs into a standard duplex receptacle. It features uniquely designed repositionable outlets and protects against damaging power disturbances traveling through your wiring into your electrical outlets. REPOSITIONABLE OUTLETS Plugs into standard 120V, 15A electrical outlet Total peak surge current capacity of 39 ka Cables for telephone, video, and data connectors included Repositionable outlets rotate to accommodate available space Perfect for tight spaces, behind furniture and appliances Intelligent monitoring against improper wiring/grounding 60 db maximum high frequency Operational indicator lamp AC Power Protection Nominal Operating Voltage 120 VAC, Single Phase Operating Voltage Range 120 VAC +/- 10% Operating Hz Rated Output 15A ANSI/IEEE C62.41 Category Category A & B (6) 5-15R Receptacles and 5-15P Plug Phase Configuration 2 Wire + Gnd Size 7.5 x 4.75 x 1.75 (Inches) Enclosure High Impact Plastic 2.0 lbs (0.9 kgs) Modes Of Protection L N, L G, N G Indication Of Suppression Status Status Indicator Response Time <.5 ns Normal Mode Certification ANSI/UL 1449 Third Edition Type 3 Maximum Continuous Operating Voltage (MCOV) Line To Neutral (8 x 20 ms) Line To Neutral Line To Ground Neutral To Ground Total 130 VAC 13 ka 13 ka 13 ka 39 ka ANSI/IEEE C62.41 Cat A Ringwave (6 kv, 200A, 100 khz) Normal Mode Common Mode ANSI/IEEE C62.41 Cat B Ringwave (6 kv, 500A, 100 khz) Normal Mode Common Mode Frequency Response Normal Mode Common Mode Low Voltage Protection 265V 290V 275V 290V 60 db Maximum, Forward/Reverse, 100 khz to 50 MHz 40 db Maximum, Forward/Reverse, 5 MHz to 50 MHz Video 1 & 2 Phone Network Type F Type RJ-11 Type RJ-45 Cables Provided 6 (2x) Type F RJ-11 Male RJ-45 Male 6' Ends 6' Ends Ends 5 ka 2 ka 3 ka (8 x 20 µs) (10 x 1000 µs) (8 x 20 µs) Capacitance <12 pf <50 pf <70 pf Protection Level L-G T-R, T-G, R-G L-G (8 Lines) (DC) 145 V V 30 V Attenuation 1 2 Ghz N/A N/A 20

23 Burglar 12VDC Edco FAS-TEL and FAS-31XT RJ11/RJ31X Telephone Protection The Edco FAS-TEL and Edco FAS-31XT are single-pair telephone or data line protectors that implement advanced two-stage hybrid design. These units address over-voltage transients with silicon breakover devices, while sneak and fault currents are mitigated with PTC technology which consists of solid state resettable fuses. The Edco FAS-31XT replaces the RJ31X jack with a protected version. Four screw terminals are provided to wire the protector in the same manner as a standard RJ31X jack. The Edco FAS-TEL is nearly identical to the Edco FAS-31XT except with out the shorting bars. Two screw terminals are provided to connect the incoming telephone line to the protector. Protected equipment such as modems are plugged into the female modular jack on the Edco FAS-TEL. <1 nanosecond response time Solid-state silicon breakover technology Low capacitance Over current protection UL 497A listed Line-to-line protection Line-to-ground protection Polyswitch resettable fuses PTCs How To Specify The Appropriate Model 12, 24, 43, 52, 180, 220, & 220 VDC 15, 30, 50, 60, 200, 270 & 300 VDC Operating Current 0.15A Dimensions (Inches) Certifications FAS-TEL-060T FAS-TEL-200T FAS-31XT FAS-TEL-DSL 160A (10 x 1000 µs T & R to Ground) 0 to 20 MHz < 0.1 db at 20 MHz Silicon Avalanche Diode w/ Series PTC Terminal Block w/compression Lugs In/ RJ Connector Out 1H x 2W x 2L 2 oz UL 497A, CUL Digital Phone Analog Phone/Fax/Modem Alarm System Phone DSL F A S - T E L - T F A S X T F A S - T E L - D S L Clamping Voltage 15 Volts 30 Volts 50 Volts 60 Volts 200 Volts 270 Volts 300 Volts 21

24 Burglar 12VDC Edco TER Series Single-Pair Medium Duty Low Voltage Zone/Horn/Strobe/Data The Edco TER surge suppressor directly installs onto electronic circuit wiring terminal screws. This close proximity preserves Edco TER s response time, clamping level and ground reference by elimi nating lead lengths. The Edco TER s miniature size fits directly inside fire or security panels, CCTV housings and other system electronic enclosures. These features maximize surge suppression performance while reducing hardware and labor costs to install. Fits Euro style and barrier strip terminals Automatic recovery Single-pair protection High energy silicon avalanche technology UL 497B listed Operating current > 2 Amps Compact size: 1.3" x 0.4" x 2" (HxWxL) 15, 30, 40 VDC 18, 33, 43 VDC Operating Current 0.09A (10 x 1000 µs) 018 = 215A, 033 = 108A, 043 = 81A 0 to 20 MHz <0.1 db at 20 MHz Silicon Avalanche Diode (SAD) Terminal Block w/compression Lugs Terminals Accept Up To 12 AWG Dimensions (Inches) 1.3H x 0.4W x 2.0L Certification 0.6 oz UL 497B Fits In Series With Circuits Wires At The Terminal Screws Zone, Buss, Loop, Data, Receive, Bell, Horn, Strobe, Pan/Tilt & CCTV TER-018 (For 12 VDC Systems) TER-033 (For 24 VDC Systems) TER-043 (For 24 VDC Systems) Edco PC2-TEL Two-Line Telephone Protection (Modular) EDCO PCB1B BASE SOLD SEPARATELY The Edco PC2-TEL is a solid state, two-line telephone interface protector module. This unit is specifically designed to protect both phone lines required by commercial security panels. Tip-to-ring protection Tip- and ring-to-ground protection Over-current protection Resettable solid state fuses PTCs UL listed 497A Requires PCB1B base PC642PTU (Pass Thru Unit) available for troubleshooting 250 VDC 270 VDC Operating Current 0.15A 160A (10 x 1000 T & R To Ground) 0 to 20 MHz < 0.1 db at 20 MHz Series PTC and Silicon Avalanche Diode (SAD) Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 2H x 1W x 2.5L (PC2TEL + PCB1B Base) Certifications 1 oz UL 497A, CUL 22

25 Access Control Protecting Access Control Systems Application Drawing SP 1 Door Lock Power Supply Dial-Up Com SP 8 SP 7 Access Control Panel SP 2 SP 3 SP 4 SP 5 RS-485/RS-422 Circuit Electric Strike or Maglock Circuit Card Reader (Wiegand) SP 3 Circuit for Device Outside of Building To Head-End or Other Control Panels SP 4 SP 2 LAN/ WAN AC Power SP 1 SP 5 SP 6 Gate Position Switch Gate Lock/Control Legend SP 1... HSP-121BT1RU SP 2... PC642C-008LC* SP 3... EL-EDS SP W8-30* SP 5... FAS-1-xxxHC SP 6... FAS-2-xxxHC SP 7... LCDP-xxx SP 8... FAS-31XT *Needs PCB1B Base 23

26 Access Control Edco EL-EDS Electric Door Suppressor The Edco EL-EDS suppressor kit is intended for installation with electrical switching devices that are connected through a relay contact on typical access control panels. The Edco EL-EDS protects against electrical anomalies (transients) that are generated as a result of the collapsing electrical field of an electromagnetic switching device (maglock or electric strike). The Edco EL-EDS provides protection for both relay contacts and control panel. <1 Electromagnetic protection 2 devices per package Relay contact and control panel protection Installation Operating Current Dimensions (Inches) Warranty 52 VDC 56 VDC NA 500 A 0 to 20 MHz <0.1 db at 20 MHz SAD w/filtering Capacitor Wire Leads -40 C C 8 L 1 oz 5 years The diagram below illustrates the proper installation of the Edco EL-EDS. For each maglock or electric strike circuit, you will need to install a suppressor (1) across the relay contacts and (2) across the leads connected to the lock solenoid (locate as close as possible to the solenoid). The suppressor wires can be installed without regard to polarity. If your package does not contain two (2) devices, contact your distributor. 24

27 Access Control Edco 5W8-30 Two-Pair Data/Signal Line Power The Edco 5W8-30 is an access control protection module designed for typical Wiegand outputs for access devices. This is a 5-wire module that accommodates low voltage data lines for 5 VDC circuits. Fifth wire power protection will allow up to 24 VDC. EDCO PCB1B BASE SOLD SEPARATELY In addition, sneak and fault currents are mitigated with resettable fuses (PTCs). The PTCs increase resistance several orders of magnitude when overcurrents exceed safe levels. A normal state resumes when over-currents are removed. The ability to self restore in this manner significantly increases suppressor performance and survivability. Automatic recovery Fast response time Resettable fusing PTCs Plug-in module Data and power protection combined Sneak/fault current protection (data only) Silicon avalanche technology Requires Edco PCB1B base PC462 PTU (Pass Thru Unit) available for troubleshooting Note: The hybrid design of this product includes series resistance. Do not use this device if data pairs are capable of continuously supplying more than 150 milliamperes. 5 VDC (Data) & 24 VDC (Power) 8 VDC (Data) & 30 VDC (Power) Operating Current 0.15A Data = 125A (10 x 1000 µs) Power = 500 A (8 x 20 µs) 0 to 20 MHz < 0.15dB at 20 MHz MOV, SAD, w/ Series PTC Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 2H x 1W x 2.5L (5W PCB1B Base) 1 oz Installation DC Power T-Tap Positive Common Wire Here Ground Terminal To Building-Approved Ground (Preferably AC Power Safety Ground) DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. 25

28 Access Control Edco FAS-TEL and FAS-31XT RJ11/RJ31X Telephone Protection The Edco FAS-TEL and Edco FAS-31XT are single-pair telephone or data line protectors that implement advanced two-stage hybrid design. These units address over-voltage transients with silicon breakover devices, while sneak and fault currents are mitigated with PTC technology which consists of solid state resettable fuses. The Edco FAS-31XT replaces the RJ31X jack with a protected version. Four screw terminals are provided to wire the protector in the same manner as a standard RJ31X jack. The Edco FAS-TEL is nearly identical to the Edco FAS-31XT except with out the shorting bars. Two screw terminals are provided to connect the incoming telephone line to the protector. Protected equipment such as modems are plugged into the female modular jack on the Edco FAS-TEL. <1 nanosecond response time Solid-state silicon breakover technology Low capacitance Over current protection UL 497A listed Line-to-line protection Line-to-ground protection Polyswitch resettable fuses PTCs How To Specify The Appropriate Model 12, 24, 43, 52, 180, 220, & 220 VDC 15, 30, 50, 60, 200, 270 & 300 VDC Operating Current 0.15A Dimensions (Inches) Certifications FAS-TEL-060T FAS-TEL-200T FAS-31XT FAS-TEL-DSL 160A (10 x 1000 µs T & R to Ground) 0 to 20 MHz < 0.1 db at 20 MHz Silicon Avalanche Diode w/ Series PTC Terminal Block w/compression Lugs In/ RJ Connector Out 1H x 2W x 2L 2 oz UL 497A, CUL Digital Phone Analog Phone/Fax/Modem Alarm System Phone DSL F A S - T E L - T F A S X T F A S - T E L - D S L Clamping Voltage 15 Volts 30 Volts 50 Volts 60 Volts 200 Volts 270 Volts 300 Volts 26

29 Access Control edco hsp121bt-1ru Edco HSP Series 120 VAC Heavy Duty 120 Volt AC The Edco HSP Series is an advanced three-stage hybrid, solid state, powerline protector. such as noise filtering, common mode and normal mode suppression, nanosecond reaction time, power line tracking, and compression screw terminations make the Edco HSP Series an excellent choice in commercial and industrial applications. The Edco HSP Series offers a replaceable fuse designed to remove the load (protected equipment) from the line if the unit is either overloaded or the internal protection fails. This feature prevents surges from entering equipment through a failed protector not noticed by the user. edco hsp121a Fast response time Failure indicator Power line tracking Filtering Polycarbonite NEMA 4X enclosure (HSP121A) Three-stage hybrid design Replaceable fuse 1/2" or 3/4" knockouts for nipple conduit connectors (HSP121A) Dimensions Operating Current I-Nominal (In) Total Operating Frequency EMI Attenuation (100 khz to 100 MHz) Modes Of Protection Status Indication 120 VAC 325 VAC 15A 3 ka 39 ka (8 x 20 µs) Hz > 40 db Metal Oxide Varistors (MOVs) w/ L-C Filter Line-to-Neutral, Line-to-Ground, Neutral-to-Ground Power On & MOVs functional 3 Position, 20A Terminal Block w/compression Screws Terminals Accept Up To 14 AWG Dimensions (Inches) HSP121BT-1RU 1.8H x 2.9W x 5.3L HSP-121A 2.95H x 4.95W x 3L 10 oz Certifications HSP121BT-1RU ANSI/UL1449 Third Edition, Type 4 HSP121A ANSI/UL1449 Third Edition, Type 2 Mounting HSP121BT-1RU Holes 3/16" Dia. Light On Normal Light Off Requires Service Mounting HSP121A Holes 3/16" Dia. 3/4" Conduit Fitting 3/4" Conduit Fitting GND 1/2" Conduit Fitting N N 1/2" Conduit Fitting AC GND AC 27

30 Access Control Edco PC642 Series Zone/Loop/Data The Edco PC642 Series surge suppressor is a two-pair (four-wire) module implementing three-stage hybrid technology. This module addresses over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak and fault currents are mitigated with resettable fuses (PTCs). The PTCs increase resistance by several orders of magnitude when over-currents exceed safe levels. A normal state resumes when over-currents are removed. The ability to self-restore in this manner significantly increases suppressor performance and survivability. EDCO PCB1B BASE SOLD SEPARATELY OPTION: DIN RAIL KIT AVAILABLE ORDER PART # 11604KIT-PC The Edco PC642 Series card edge module is gold plated, double sided, and is designed to mate with the Edco PCB1B gold-plated female terminal connector. When snapped together, the data circuits pass thru the protector in a serial fashion from the four Field Side terminals to the four Electronics Side terminals. Terminals 1 or 10 of the Edco PCB1B must be attached to Building- Approved Ground per Edco Technical Bulletin # Three-stage hybrid protection Sneak/fault current protection Resettable fusing PTCs Low capacitance option Plug-in module Fast response time Requires Edco PCB1B base Order PC642PTU an invaluable troubleshooting tool 5, 12, 18, 24, 30, 36, 43, 52, 180 VDC 8, 15, 20, 30, 36, 43, 50, 60, 200* VDC Operating Current 0.15A 10 ka (8 x 20 µs) 0 to 20 MHz < 0.1 db at 20 MHz GDT, SAD, w/series PTC Terminal Block w/compression Lugs Terminals Accept Up To 10 AWG Dimensions (Inches) 2H x 1W x 2.5L (PC642 + PCB1B Base) Certification 1 oz UL 497B * PC642C-200 is not UL certified Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of supplying more than 150 milliamperes continuously. Terminal Assignments Unprotected Pair 2 Field Side Unprotected Pair 1 Odd Terminals { { PCB1B: 1.0 Even Terminals } Protected Pair 2 Electronics Side 2.125" 2.4" 2 } Protected Pair 1 Keying Pin Ground Terminal 1 Or 10 To Building-Approved Ground DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. PC642 PCB1B APPLICATION: RS485, RS422: PC642C-008LC & PCB1B RS423, Token Ring: PC642C-008LC & PCB1B RS232: E-Net, 10 Base T: PC642C-020 & PCB1B PC642C-030LC & PCB1B 4 20 ma: PC642C-036 & PCB1B How To Specify The Appropriate Model PC642C - Voltage Clamp 8 Volts Volts Volts Volts Volts Volts Volts Volts **200 Volts **Not UL Listed no suffix stage 2 clamp each line-to-ground stage 2 clamp D line-to-line only stage 2 clamp line-to-line X and each line to ground low capacitance option stage LC 2 clamp line-to-line and each line to ground 28

31 Access Control Edco LCDP Data Circuit Protection The Edco LCDP Series is designed to conveniently protect 8 wire, low voltage, data circuits and employs two RJ-45 jacks for easy installation. The Edco LCDP utilizes silicon avalanche (solid-state) suppression technology and exhibits very low capacitance to accommodate high data rates. This unit supports high-speed data rates of over 100 Mbps. <1 nanosecond response time Line-to-line protection Low capacitance RJ-45/4 pair protection (8 wire) Silicon avalanche design Line-to-ground protection 5, 12, 24, 48, 65 VDC 8, 15, 30, 60, 75 VDC Operating Current 1.5A (10 x 1000 µs) 008 = 125A, 015 = 72A, 030 = 22A, 060 = 18A, POE*=15A 0 to 100 MHz < 0.1 db at 50 MHz Silicon Avalanche Diode (SAD) RJ-45 Jacks Dimensions (Inches) 1.0H x 2.5W x 4.25L Certification * LCDP-POE is not UL certified 3 oz UL 497B Installation The user equipment plugs into the LCDP s equipment (protected) side, and the LCDP s line (unprotected) side is connected to the incoming line. All 8 conductors are protected. The green ground wire must be bonded to the protected equipment power ground (third wire, green wire safety ground). Do not add length to the ground wire, since it must be kept as short as possible. Model LCDP-008 LCDP-015 LCDP-030 LCDP-060 LCDP-POE* 8 Volts 15 Volts 30 Volts 60 Volts 75 Volts 29

32 Communications Edco FAS-1 and FAS-2 Series One- and Two-Pair Signal Line Protection The Edco FAS-1 and Edco FAS-2 Series are multi stage one-pair or two-pair surge suppressors designed for high-exposure applications. These products were specifically designed to meet multiple, low voltage, protection applications in the fire and security industries. Lightning protection for low voltage Data/signal lines Multi stage protection Common mode and differential protection mode Automatic recovery 15, 24, 36, 52 VDC 18, 33, 43, 60 VDC Operating Current 2.5A 10 ka (8 x 20 µs) 0 to 10 MHz < 0.1 db at 10 MHz GDT, SAD, w/series Inductor Terminal Block w/compression Lugs Terminals Accept Up To 12 AWG -40 C to +85 C Dimensions (Inches) FAS-1 = 1.5H x 1.5W x 2.8L FAS-2 = 2H x 2W x 2.8L FAS-1 = 3.5 oz FAS-2 = 7 oz Certification UL 497B Installation Unprotected Or Field Side Ground Lug AWG < 3 Equip. Line FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair) FAS HC (Two-pair) FAS HC (One-pair)* FAS HC (Two-pair)* *Not UL listed 12VDC Use 24VDC Use 24VAC Use 48V Systems Use Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continuously supplying more than 2.5 amperes. Protected Equipment DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. 30

33 Communications Edco DRS (DC) Series DIN Rail Protection The Edco DRS (DC) Series is a din rail mountable, single-pair surge suppression module implementing three-stage hybrid technology. This module addresses over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak currents are mitigated with resettable fuses (PTCs). The PTCs increase resistance several orders of magnitude when over-currents exceed safe levels. A normal state resumes when over-currents are removed. The ability to self-restore in this manner significantly increases suppressor performance and survivability. The Edco DRS (DC) Series mounts onto a standard 35 mm industrial DIN rail. There are three Field Side and three Electronics Side screw terminals. One is reserved for a shield. Three electrically tied ground terminals are provided for grounding the Edco DRS (DC) Series unit to Building-Approved Ground. Shield is isolated from ground. For a 2-terminal version without a shield, order the Edco DRS-XXX-2. Low-voltage data surge protection Three-stage hybrid protection Sneak/fault current protection with resettable fuses PTCs Low profile packaging UL 497B listed Easy installation Fits standard 35 mm DIN rail Fast response time < 1 nanosecond Maximum Nominal Surge Peak Current Typ Maximum Nominal Part Peak Signal Breakdown 1p 10 x 1000 µs 8 x 20 µs Cap Continuous Series Number Voltage Voltage Current Waveform (pf) Current (ma) Resistance DRS > ka Ohms DRS > ka Ohms DRS > ka Ohms DRS > ka Ohms DRS > ka Ohms DRS > ka Ohms DRS > ka Ohms DRS > ka Ohms *DRS >10 8 ka Ohms **DRS >10 8 ka None Dimensional Diagrams DRS-XXX *Not UL 4978 Listed **Warning!! DRS-130RMS is for discrete signal use only. Do not use DRS-130RMS on 120 VAC power lines. This unit is a nonhybrid, MOV design, rated above 5A operational current and can withstand greater than eight occurrences of a 10 ka (8 x 20 µs) waveform, and greater than 1,000 occurrences of a 200A 10 x 1000 µs waveform. DRS-XXX-2 (2 Terminal Version) 31

34 Communications Edco CX-HFN High Frequency Coax Protector N-Type The Edco CX-HFN surge protectors are designed to protect sensitive electronic equipment from damage due to excessive voltage or currents generated by lightning or static buildup. The Edco CX-HFN offers low signal loss at frequencies up to 3 gigahertz. The Edco CX-HFN accommodates both bulkhead mount and stud mount. The input and output connections are interchangeable. Operating Current 130 VDC 150 VDC (DC Spark Over Voltage) 1A 10 ka (8 x 20 µs) 0 to 4 GHz < 0.5 db 2 to 3 GHz Gas Discharge Tube (GDT) Female N-Type Dimensions (Inches) 1.25H x.875w x 2.5L 4 oz CX-HFN-FM Female to Male CX-HFN-FF Female to Female Edco CATV-DF High Frequency Coax Protector F-Type The Edco CATV DF surge protectors are designed to protect sensitive electronic equipment from damage due to excessive voltage or currents generated by lightning or static buildup. Applications include direct broadcast satellite systems, HDTV, and cable modems. The Edco CATV DF offers low signal loss at frequencies up to 2 gigahertz. Incorporates GDT (gas discharge tube) technology. Automatic recovery Low insertion loss Shielded case Easily installed 25 VDC 0 to 2 GHz Operating Current 150 VDC (Spark Over Voltage) 1A < 1.0 db at 1 GHz < 2.0 db at 2 GHz Gas Discharge Tube (GDT) Dimensions (Inches) 1.25H x 2.5W x 4L 3 oz 10 ka (8 x 20 µs) Type F Female 32

35 Communications Edco OPX Series Intercom/Speaker Punch Block Protection (Parallel) Medium Exposure Applications The Edco OPX Series surge protectors are specifically designed for mediumexposure applications. Thus, the protectors can be used on pairs inside a building or leaving the build ing, in conduit up to 500 feet. These protectors are intended to be used in conjunction with the Edco MGB Ground Rail and a standard MI-50 Punch Down Block. The Edco OPX Series offers several, distinct advan tages over other current technologies. Among the advantages are low cost, no series resis tance, and durable solid-state construction. Over-current protection Replaces bridging clips on MI-50 block UL 497B listed Utilizes MGB grounding rail Test point accessible 12, 24, 42, 12, 35 VDC Operating Current 15, 30, 48, 15, 56 VDC 2A 015 =125A, (10 x 1000 µs) 030 = 71A, 048 = 45A, CLN = 125A, SPK = 500A, 8 x 20 µs Insertion loss 0 to 20 MHz < 0.1 db at 20 MHz Silicon Avalanche Diode (SAD), OPX-SPK Model Uses MOV Clip Dimensions (Inches) 1.25H x 0.375W x 2.0L Certification 1 oz UL 497B Installation MI-50 Block Test Points How To Specify The Appropriate Model DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. O P X C L N S P K Clamping Voltage 15 Volts 30 Volts 48 Volts 15 Volts (Call-In Circuit) 56 Volts (Speaker Circuit) 33

36 Communications Edco PB Series Intercom/Speaker Punch Block Protection (Series) The Edco PB modules are solid-state protectors for intercom extension pairs. As a new alternative to the OPX, the standard EDCO intercom protector, the PB adds fusing and a new component layout. These hybrid protectors are intended to be used in conjunction with the EDCO MGB ground rail and a standard MI-50 punch down block. The PB modules feature solid-state resettable fuses (PTCs) between the protected equipment and the over voltage clamping components. This unique design prevents problems with All-Call in the event of catastrophic protector failure. Patented Technology Over current protection Replaces bridging clips on M1-50 bock UL 497B listed Utilizes MGB grounding rail Test point accessible Installation 12, 56 VDC 21, 70 VDC Operating Current 0.15A PBCLN = 0.2 ka, PBSPK = 0.5 ka (10 x 1000 µs) 0 to 20 MHz PBCLN = SAD w/series PTC, PBSPK = MOV w/series PTC < 0.1 db at 20 MHz Clip Dimensions (Inches) 1.25H x 0.4W x 2.8L Certification 1 oz UL 497B MI-50 Block Test Points PBCLN Call-In Circuit PBSPK Speaker Circuit See technical Bulletin # 2017 Caution: The hybrid design of this product includes series resistance. Do not place this product in service on any signal line capable of continu ously supplying more than 150 ma. TTA-2: Test Point Plug Available DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. 34

37 Communications Edco H Series Telecom/Punch Block Protection Advanced Ultra High Speed Technology Patented Technology The Edco H Series modules are ultra high speed, fused, solid state, secondary protectors for KEY/PABX systems. The units are available in three different clamping voltages. The Edco H Series is constructed with solid state silicon foldback technology, polyswitch resettable fuses PTCs and failure fuses. These protection modules are intended to be used in conjunction with proper primary protectors (UL 497A). The protective elements switch from the normal high-impedance state to a low-impedance state upon a detection of a surge, then switch back to high impedance after the surge has passed. The Edco H Series single-pair modules fit onto a standard Edco MI-50 split block and replace bridging clips. In addition, these modules require the Edco MGB Ground Rail for each Edco MI-50 block used. 50, 180, 230 VDC 65, 200, 270 VDC Operating Current 0.15A 160A (10 x 1000 µs T & R to Ground) 0 to 20 MHz < 0.1 db at 20 MHz Silicon Breakover Device w/series PTC Clip Dimensions (Inches) 1.25H x 0.4W x 2.8L Certifications 1 oz UL 497A, CUL Installation MI-50 Block HCO Central Office/Trunk HAE Analog Extension HDE Digital Extensions Unprotected Side Terminate Field Side Wiring Coming Into Building On The Unprotected Side DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. 35

38 Communications Edco COHP Series Data/Signal Line/Punch Block Protection High-Exposure Applications The Edco COHP modules are three-stage hybrid protectors for low-voltage data and telecommunications applications. The modules address over-voltage transients with gas tubes and silicon avalanche components. In addition, sneak and fault currents are mitigated with resettable fuses (PTCs). Intended to be used on pairs without the presence of ring ing voltage. The Edco COHP modules are designed for data and control applications as an isolated loop circuit protector. Replaces bridging clips on MI-50 Block <1 nanosecond response time Line-to-line protection Line-to-ground protection Utilizes MGB grounding rail Rugged, three electrode, gas tube, first stage Silicon avalanche hybrid technology Polyswitch resettable fusing PTCs 6, 12, 20, 24, GDT, SAD, w/ Series PTC Model 43, 52 VDC Clip COHP Volts 8, 15, 20, 30, 50, 60 VDC COHP Volts Operating Current 0.15A Dimensions (Inches) 1.25H x 0.4W x 2.8L COHP Volts 10 ka (8 x 20 µs) 1 oz COHP Volts 0 to 20 MHz Certification UL 497B COHP Volts < 0.1 db at 20 MHz COHP Volts Edco MGB Ground Rail Fits Standard 66MI-50 Punch Down Blocks Split Block Variations The Edco MGB Ground Rail designed to fit standard 66MI-50 Punch Down Blocks. Allows Edco s H Series, COHP, OPX, PB Series and other similar surge suppressors to access ground when snapped onto the 66MI-50 Punch Down Block. The Standard 66MI-50 Block is capable of accommodating up to 25 Edco surge suppressors. Protected Unprotected U.S. Patent No. 4,703,983 MI-50 Block DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. Edco Recommends A 10AWG Wire To Building-Approved Ground Keep Short 36

39 Communications Edco FAS-TEL and FAS-31XT RJ11/RJ31X Telephone Protection The Edco FAS-TEL and Edco FAS-31XT are single-pair telephone or data line protectors that implement advanced two-stage hybrid design. These units address over-voltage transients with silicon breakover devices, while sneak and fault currents are mitigated with PTC technology which consists of solid state resettable fuses. The Edco FAS-31XT replaces the RJ31X jack with a protected version. Four screw terminals are provided to wire the protector in the same manner as a standard RJ31X jack. The Edco FAS-TEL is nearly identical to the Edco FAS-31XT except with out the shorting bars. Two screw terminals are provided to connect the incoming telephone line to the protector. Protected equipment such as modems are plugged into the female modular jack on the Edco FAS-TEL. <1 nanosecond response time Solid-state silicon breakover technology Low capacitance Over current protection UL 497A listed Line-to-line protection Line-to-ground protection Polyswitch resettable fuses PTCs How To Specify The Appropriate Model 12, 24, 43, 52, 180, 220, & 220 VDC 15, 30, 50, 60, 200, 270 & 300 VDC Operating Current 0.15A Dimensions (Inches) Certifications FAS-TEL-060T FAS-TEL-200T FAS-31XT FAS-TEL-DSL 160A (10 x 1000 µs T & R to Ground) 0 to 20 MHz < 0.1 db at 20 MHz Silicon Avalanche Diode w/ Series PTC Terminal Block w/compression Lugs In/ RJ Connector Out 1H x 2W x 2L 2 oz UL 497A, CUL Digital Phone Analog Phone/Fax/Modem Alarm System Phone DSL F A S - T E L - T F A S X T F A S - T E L - D S L Clamping Voltage 15 Volts 30 Volts 50 Volts 60 Volts 200 Volts 270 Volts 300 Volts 37

40 Communications MODEL SHOWN 48 CAT6-POE Edco RM-CAT6-POE Series Multi-Channel Rackmount The Edco RM-CAT6-POE Series is a modular, high speed, data-line protector that utilizes a three-stage hybrid design technology. This unit addresses highenergy voltage transients that can damage expensive computer equipment. Ideal for network switches and hubs, the Edco RM-CAT6-POE Series is easily mounted in close proximity to the protected equipment. Exceeds Category 6 transmission values Compact 1U rack size Replaceable surge modules Low insertion loss Offered in 16 or 48 channel protection* Three-stage hybrid Meets POE requirements 1 year warranty *Other configurations available. Consult factory. 57 VDC 68 VDC MHz Operating Current 0.15A Modes of Protection GDT, SAD, W/Series PTC Signal High-Low Signal High-Ground, Signal Low-Ground 10 ka (8 x 20 µs) <0.1dB VSWR <1.2 Operating Humidity 0-95% Non-Condensing Input RJ-45 Output RJ-45 Mounting Rackmount Enclosure Type Painted Steel Dimensions 1.75Hx19Wx6.3D 5.5 lbs. Edco LCDP Data Circuit Protection The Edco LCDP Series is designed to conveniently protect 8 wire, low-voltage data circuits and employs two RJ-45 jacks for easy installation. The Edco LCDP utilizes silicon avalanche (solid-state) suppression technology and exhibits very low capacitance to accommodate high data rates. This unit supports high-speed data rates of over 100 Mbps. <1 nanosecond response time Line-to-line protection Low capacitance RJ-45/4 pair protection (8 wire) Silicon avalanche design Line-to-ground protection 5, 12, 24, 48, 65 VDC 8, 15, 30, 60, 75 VDC Operating Current 1.5A (10 x 1000 µs) 008 = 125A, 015 = 72A, 030 = 22A, 060 = 18A, POE*=15A 0 to 100 MHz < 0.1 db at 50 MHz Silicon Avalanche Diode (SAD) RJ-45 Jacks Dimensions (Inches) 1.0H x 2.5W x 4.25L Certification 3 oz UL 497B (*except LCDP-POE) Installation The user equipment plugs into the LCDP s equipment (protected) side, and the LCDP s line (unprotected) side is connected to the incoming line. All 8 conductors are protected. The green ground wire must be bonded to the protected equipment power ground (third wire, green wire safety ground). Do not add length to the ground wire, since it must be kept as short as possible. LCDP-008 LCDP-015 LCDP-030 LCDP-060 LCDP-POE 8 Volts 15 Volts 30 Volts 60 Volts 75 Volts 38

41 Communications Edco RJA-RJD Series RJ-45 Telephone/Data The Edco RJA and Edco RJD Series are four-pair telephone/data-line protectors that implement advanced, two stage, hybrid design. These units address over voltage transients with silicon breakover devices, while sneak and fault currents are mitigated with PTC technology, which consists of solid state resettable fuses. The Edco RJA and Edco RJD Series incorporate Edco RJ-45 female jacks in and out. The Edco RJA voltage clamp is set for C.O. Trunks and analog telephone extensions (with ring in voltage), and the Edco RJD voltage clamp is set for digital extensions (no ring in voltage). <1 nanosecond response time Solid-state resettable fuses PTCs Silicon breakover technology Low capacitance Line-to-line protection Tip- and ring-to-ground protection CAN/CSA C22.2, No compliant UL 497A listed 4 pair protection Installation 48, 220 VDC 55, 280 VDC Operating Current 0.15A 200 A (10 x 1000 µs) 0 to 50 MHz < 0.1 db at 50 MHz Silicon Breakover Devices w/series PTC RJ-45 Jacks Dimensions (Inches) 1.0H x 2.5W x 4.25L Certifications 3 oz UL 497A, CUL Gnd. Analog Phone Digital Phone Building- Approved Ground RJA-45 RJD-45 The Edco RJA and Edco RJD Series are intended for indoor use only and shall be employed on the equipment side of a listed primary telephone protector. 39

42 Communications Edco TBLK Assembly Terminating Assembly The Edco TBLK is a high-density assembly designed to house up to 12 or 25 individual Edco surge protec tion modules. Standard Edco H Series, COHP, OPX, PB Series, and other similar modules (separately ordered) are suitable for the Edco TBLK assembly. The Edco TBLK is capable of terminating solid or strand ed 26 to 14 AWG wire using compression terminal screws. Dimensions DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. Edco CAT6-5POE Series CAT6/CAT5 Power Over Ethernet The Edco CAT6-5POE Series is designed to work on Category 5 Power-Over- Ethernet transmission lines as well as Category 6 applications. Ideal to protect expensive equipment against surges and transients entering a building on exposed transmission lines. Available in both female to female and male to female RJ-45 connectors. Exceeds CAT5 & 6 transmission values CAT5 POE compatible CAT6 compatible Applications up to ma 1 year warranty Operating Voltage 60 VDC RJ-45 Jacks RJ-45 (FF) CAT6-5POE-FF 65 VDC RJ-45 (MF) CAT6-5POE-MF Operating Current 300 ma 60A (10 x 1000 µs) 0 to 250 MHz Dimensions (Inches) 0.8H x 1.0W x 2.3L (FF). 0.8H x 1.0W x 3.0L (MF) 1 oz < 0.1 db at 20 MHz Silicon Avalanche Diode (SAD) 40

43 Communications Edco MOD-12 Key Systems The Edco MOD-12 Tip/Ring protection for Key/PBX Systems. This innovative design creates an automatic ground window, thus eliminating the problem of ground potential difference. Edco H Series Protector Modules readily snap onto the Edco MOD-12. Protection is expandable from 1 to 12 pairs in single-pair increments and is field upgradable. In addition, test points are provided on each pair. 1 to 12 pair expansion Replaceable single-pair protection modules Punch down block (66 type) Test points Protective transparent cover UL 1363 listed AC Protection Options Application Diagram 1. Basic internal surge protection (standard) 2. Plug-in hybrid surge protection HAE or HDE (One Per Extension) HCO (One Per CO TRUNK) Existing Telco Primary Protection Demarc 66 Block Tip/Ring Or Data Protection 1. Incoming C.O. lines use HCO 2. Analog extensions use HAE 3. Digital extensions use HDE HAE HDE MGB Ground Rail KSU MOD-12 CO TRUNKS MOD-12 Base Assembly Chassis Ground Cable Shield Ground To AC Building-Approved Ground DO NOT daisy chain grounds. NOT intended for shield termination. Install ground in accordance with all applicable codes. 41

44 Headquarters Surge Protection 100 Emerson Parkway Binghamton, NY T: T: F: E: Emerson Network Power. The global leader in enabling Business-Critical Continuity TM. EmersonNetworkPower.com/surge AC Power Connectivity DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks and Integrated Cabinets Services Surge Protection Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co Emerson Electric Co. While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. SL Rev.1 8/10 Printed in USA