ABOUT US. P01/P02

Transcription

1 Suncore USA Tel: Website: Address: 3825 Academy Pkwy South NE, Albuquerque, NM, USA Suncore China Tel: Fax: Website: Address: 188 Taifeng Boulevard, Huainan High-tech Development Zone Huainan, Anhui province, China.

2 ABOUT US Suncore Photovoltaic Technology Company Limited is 100% owned by Fujian SanAn Group. Headquartered in Huainan, Anhui Province, Suncore also has 100% owned subsidiaries located in Albuquerque, NM USA, Xining China, and Xiamen China. Built upon state-of-the-art automated manufacturing technologies and strong research and development (R&D) capabilities, Suncore manufactures a complete offering of solar concentrator solutions for utility-scale, and industrial solar hot water. In addition to manufacturing, Suncore also provides full Engineering Procurement and Construction (EPC) services in addition to financing solutions for solar project development. Full vertical integration as a technology provider through project development and financing, allows Suncore to provide exceptionally competitive CPV solutions to its customers and partners worldwide. With an annual production capacity of more than 300MW, Suncore is dedicated to providing its clients with high performance, high quality CPV products and services. Continuous dedication to R&D, Suncore is continually improving CPV system and module efficiency furthering the CPV competitive advantage in high direct normal irradiance (DNI) regions of the world. P01/P02

3 MILESTONE % Owns Golmud 60MW CPV Power Plant, the 2002 San an solar power division was formed Solar cell (San an) passed the CASC test Generation I CPV demo system successfully built up Generation II CPV system was put into commercial use. Suncore was established by San an Optoelectronics and Emcore Corporation Relocated to Huainan, Anhui Province, committed to creating the 2012 Production commencement of the first CPV automation line in the world; 50MW CPV power plant in Golmud completed San an became the sole shareholder through its purchase of the 40% of Suncore stock owned by Emcore. largest one in the world, was completed. world-class CPV manufacturing base. P03/P04

4 UTILITY-SCALE CPV POWER PLANTS Golden Sun 1.5 MW Commercial Ground and Rooftop CPV system in Xiamen, Fujian Province, China Golmud60MW Location: Golmud, Qinghai Province, China DNI: 4.86 kwh/m2/day Size: 60 MW Year of COD: 2013 Suncore s Involvement: Developer Description: The 60MWac plant Located in the Qinghai province in the northwest of the Peoples Republic of China. The solar park is located on the Qinghai-Tibet plateau and sits above 9,000ft in altitude. This plant was developed and is owned and operated by Suncore Photovoltaic Technology Co. Ltd. Upon commissioning this plant was the largest CPV installation worldwide. EVORA 1MW, CPV Ground system, Evora, Portugal Eubank Landfill Solar Array, 2 MW, Albuquerque, NM, U.S. Golmud50MW Location: Golmud, Qinghai Province, China DNI: 4.86 kwh/m 2/ day Size: 50 MW Year of COD: 2012 Suncore s Involvement: Technology Provider Description: Located in the Qinghai province in the northwest of the Peoples Republic of China. The solar park is located on the Qinghai-Tibet plateau and sits above 9,000ft in altitude. The plant was fully commissioned in November Suncore's success with this project has encouraged additional development in the area. P05/P06

5 CPV SYSTEMS Utility-ScaleConcentrator Photovoltaic(CPV)SystemSpecification The latest Suncore CPV solar system for utility-scale projects has a rated power of 2.336kW. The system was designed for ease of installation and inexpensive operation and maintenance. Modules can be installed on low profile pedestal 2 axis tracking system which minimize foundation and installation requirement and allows for optimization of filed packing density with little shadowing. Modules and motors are easily accessed from the ground, or with a short step ladder, facilitating easy and cost effective cleaning and maintenance. Each system can be remotely operated and controlled to ensure maximum availability and perfect tracking. Specifications Peak power (CSTC) Tracking accuracy 2.336±5% kwp 0.3 Features Optimized for low-cost, utility-scale installations CPV modules at 30.5% efficiency with triple junction solar cells Pedestal 2 axis tracking system Online monitoring, control and diagnostic access Easy O&M from the ground with less than 20 man hour per MW SuncoreIsYourPartnerinSuccess CPV Technology Provider (Utility and Commercial Size Projects) Financing Options for CPV Projects EPC Provider Project Development CPV Component Provider CPVT- Combined Concentrator Solar Thermal and Electric systems Size (width x height) Weight (single system) MTBF/MTTF (main parts) DC efficiency Concentration ratio 5.3mX2.1m 650kg hours 30.5% P07/P08

6 oncentrating on a Solar Future LTM LTMSpecifications Chart 1 Solar cell type Triple-junction GaAs solar cell Power output attenuation (25years) 15% Module model LTM Alpha Acceptance Angle (degrees) 0.8 Concentration ratio 625 Dielectric strength 3000VDC Size 2564x1704x109mm Solar cellsper module 1536 Ice-hail resistance Comply with IEC standards, 25mm ice ball at 22m/s Weight(single module) 145kg Protection grade IP67 The LTM low profile modules are Suncore s most cost effective and efficient module to date. LTM modules have an efficiency of 30.5% maximizing the ability to convert sunlight to electricity, making it the ideal choice for the sunniest locations around the world. The light and thin design allows for increased packing density and reduced Chart 2 CSOC CSTC shipping cost. Modules are easily installed by hand, eliminating the need for large installation equipment such as cranes and forklifts. Test condition DNI=900W/m 2 AM=1.5D DNI=1000W/m 2 AM=1.5D Features Optimized for low-cost, utility-scale installation Tam=20 o C Wind speed 2m/s Tc=25 o C Wind speed 0 Light and thin design for easy transportation and installation Peak power 0.965±5% kwp 1.168±5% kwp Using triple-junction solar cells with rated efficiencies averaging 39% Large acceptance angle reduces tracker requirements High-volume fully automated manufacturing Voc (nominal) Isc (nominal) V 1.8A V 1.78A Ump (nominal) 705.6V 746.4V Imp (nominal) 1.52A 1.48A Rated operating temperature -20 o C~+50 o C Power TC %/ o C P09/P10

7 CPVT: Z10 COMBINED HEAT & POWER Z10Specifications Data Units Z10 Dishes EA 1 Total aperture area m 2 12 General Tracking technology 2-axis Azimuth range deg Elevation range deg 5-95 CPVT: Z10 demonstration site Golmud China Electricity Tracking control Peak electrical power (DC) kwp Sensor-less closed loop 2.5 (*) Howitworks Operating voltage VDC Z10 features one 12m2 collector, mounted on a dual axis tracker that concentrates incoming sunlight onto a high efficiency multi junction solar cell receiver. The solar cells are coupled to a heat exchanger that converts concentrated solar flux into electrical power (A) and thermal power (B) Thermal Peak thermal power Fluid kwp Water or coolant 5.5 (*) (A) 2.5kW DC electrical power from the PV cells (B) 5.5kW thermal energy is pumped through a closed loop system to the various users for applications such as: Maximum supply temperature deg C 90 Hotels, Hospitals and resorts Municipalties and district heating Nominal flow l/min Correctional facilities, Military installations, Dormitories, Gated Communities Operating wind speed km/h 40 Industrial process heat: ideal for textile, food and pharmaceutical industry Thermal energy can be used for cooling in addition to desalination and brackish water purification Permissible wind speed km/h 160 Physical Dimensions Weight kg 500 Benefits Quick payback on investment, typically less than 5 years Minimal balance of system cost required Height in stowed position Height in operation m m CPVT Combined thermal and electrical solar power Designed for commercial and industrial applications Compliance Currently undergoing full certification Cell receiver designed for easy upgrade Designed for 20+ years opperational life 2-axis high precision tracking mechanism with zero backlash, using performance feedback-driven, continuous tracking optimization for maximum effectiveness Inverter Notes: (*) Tested at 1kW/m 2 irradiance. Mounting ready P11/P12

8 SOLAR RECEIVERS FOR CPV SYSTEM Features Average of 39% cell efficiency under concentrated illumination. High-speed automated assembly with low labor content, custom receiver designs and OEM services are available. Two standard form factors including 5mm x 5mm and 10mm x 10mm. Custom sizes available upon request. Exceptional thermal performance using high-quality Direct-Bond-Copper(DBC) substrates. Low thermal resistance, low electrical resistance. Annual capacity of more than 300 MW per year. 10 mm Type 10mm x 10mm Typical efficiency Cell active area Substrate Bypass diode Operating temperature Max temperature 38.5%, 25 C, AM cm 2 Direct-bond-copper, AlN substrate with Au / Ni surface plating (copper thickness 0.3mm, AlN thickness 0.63mm) 15A (Schottky) -40 C to 100 C 150 C 5 mm Open circuit voltage Short circuit current 3.20V 14.5A CTJ Solar Cells GaInP/GaInAs/Ge Suncore s CPV receivers take the world-class efficiency of CTJ solar cells and combine it with state-of-the-art automated packaging technology to create the most efficient and reliable CPV receiver for CPV systems. For many years, Suncore has utilized advanced, high-speed test and manufacturing equipment, to produce high-quality receivers to meet the rigorous demands of CPV applications. Suncore has been providing CPV receivers to some of the world s leading CPV system manufacturers. Suncore is dedicated to producing reliable and cost effective components. 5.5mm x 5.5mm Typical efficiency Cell active area Substrate Bypass diode Operating temperature Max temperature Open circuit voltage Short circuit current 39.5%, 25 C, AM cm 2 Direct-bond-copper, Al2O3 substrate with Au / Ni surface plating (copper thickness 0.3mm, Al2O3 thickness 0.38mm) 10A (Schottky) -40 C to 100 C 150 C 3.20V 4.5A P13/P14