Discovery 1-4 Loop Analogue Addressable Control Panel Application Guide

Transcription

1 Discovery 1-4 Loop Analogue Addressable Control Panel Application Guide Contents Page 1.0 Introduction and Typical System Illustration Cabinet Specifications Hardware Specifications Software Specifications Panel Enhancements Compatible Field Devices 20 Appendices i Other Relevant Documentation 22 Document Ref: Dis4app.doc / Rev Page 1 of 22 Originator MC Checked byac Approved by JBJ_

2 1.0 Introduction and Typical System Illustration The Discovery analogue addressable panel is available as a 1-4 loop panel using plug-in loop driver cards. Each loop is rated at 500mA and will control up to 126 Apollo, XP95 or Discovery devices. All addresses may be configured as cause/effect outputs, with up to 255 different programmable groups and 3 independently programmable output bits per address. Discovery mode changes are configured by the panel s internal clock and may differentiate between weekday and weekend functions. Loop inputs may also be configured to change selected loop devices between modes where temporary mode changes are required. Panels are housed in well-designed enclosures and are finished in hardwearing epoxy paint. The motherboard electronics are fixed to a detachable chassis thus facilitating a completely empty enclosure for first fix installation. Top entry plastic grommets, bottom/rear entry knockouts for mains, and rear entry knockouts are designed to assist with cable installation. The Discovery has a 4 line x 20 character backlit LCD display, showing device address, zone, type, status and location text. The LCD display is also used as a menu-driven engineers configuration display. User controls are accessed by means of keyswitch enabled membrane controls, with password protection for engineer purposes. 32 zonal LEDs are provided as standard and plug-in printer is available as an option. The panel provides 2 common fire changeover relays and 1 common fault changeover relay, each rated at 1A, 30V DC. Four fully monitored panel inputs are provided for remote silence, remote reset, remote evacuate and remote fault. The evacuate input will operate the general alarms and may be programmed to operate the fire relay. The Discovery panel may control up to 14 repeaters with full user capability via RS485 data comms. Extensive panel and network cause/effect programming is achieved via the PC programming package. Full networking with other Discovery panels, network repeaters and graphics package may be achieved with an additional plug-in network driver card. Network cause/effect may be programmed between Discovery panels, Nexus panels and active network repeaters. Document Ref: Dis4app.doc / Rev Page 2 of 22 Originator MC Checked AC_

3 FIRE PR E S S HE RE ISOLATOR ISOLATOR F IRE P RE S S HE RE FIRE PR E S S HE RE FIRE BR EAK GLASS PR E S S HE RE BR EAK GLASS A1445 A1444/7 MINI SWITCH MONITOR WITH INTERRUPT RELAY OUTPUT UNIT BR EA K GLASS EXTINGUISHING SYSTEM REMOTE INDICATOR A1445 BR EAK GLASS A1445 A1444 A1445 A1446 APOLLO TRANSLATOR BEAM DETECTOR CONVENTIONAL FIRE PANEL FIRE DAMPER MONITORING BARRIER BARRIER PANEL REPEATER HAZARDOUS AREA ALARMS FIRE & FAULT RELAYS PC UPLOAD AND DOWNLOAD PROGRAMMING DISCOVERY 1-4 PANEL FIRE & FAULT RELAYS KONEX NETWORK REPEATER ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 KONEX NETWORK REPEATER MIMIC PANEL WITH KONEX NETWORK I/O FACILITY PC ALARM MANAGER GRAPHICS SYSTEM Document Ref: Dis4app.doc / Rev Page 3 of 22 Originator MC Checked AC_

4 2.0 Cabinet Specifications 2.1 Surface Cabinets All cabinets are manufactured from 18SWG sheet steel and finished in satin texture epoxy powder stove paint. Top entry grommets and rear entry knockouts are provided. Cabinet colour: RAL 7035 Light Grey c b a 1-4 loop Repeaters Protection Plugs 13 off 13 off a 480mm 370mm b 410mm 325mm c 144mm 106mm Part No Description 2500/110 Discovery 1 loop analogue/addressable control panel with 32 zone LEDs, c/w 1 loop card, expandable to 4 loops with 2500/130 Additional loop card; Cabinet size - 480h x 410w x 144d. Space for printer and 2 x 12V 12Ah battery set. 2500/111 Discovery 2 loop analogue/addressable control panel with 32 zone LEDs, c/w 2 loop cards, expandable to 4 loops with 2500/130 Additional loop card; Cabinet size - 480h x 410w x 144d. Space for printer and 2 x 12V 12Ah battery set. 2500/112 Discovery 3 loop analogue/addressable control panel with 32 zone LEDs, c/w 3 loop cards, expandable to 4 loops with 2500/130 Additional loop card; Cabinet size - 480h x 410w x 144d. Space for printer and 2 x 12V 12Ah battery set. 2500/113 Discovery 4 loop analogue/addressable control panel with 32 zone LEDs, c/w 4 loop cards. Cabinet size - 480h x 410w x 144d. Space for printer and 2 x 12V 12Ah battery set. 2500/107 Printer 2500/130 Additional loop cards for Discovery panels Document Ref: Dis4app.doc / Rev Page 4 of 22 Originator MC Checked AC_

5 2.2 Semi-Flush Bezels The semi-flush bezel locates to the rear of the bevelled edge of the back box, leaving the bevelled edge and door raised out from the wall. Finished in the same colour as the cabinet back box and fitted by means of pinch bolts, thus avoiding the need to drill the cabinet. h c e f d a b g 1-4 loop Repeaters Hole Height a 487mm 377mm Hole Width b 417mm 332mm Hole Depth c 114mm 76mm Max Bezel Height d 543mm 433mm Max Bezel Width e 473mm 388mm Bezel Overlap f 30mm 30mm Bezel Depth g 30mm 30mm Door Protrusion h 30mm 30mm Part No Description 2501/124 Semi-flush bezel for Discovery 1-4 loop panel and repeater panels 2500/ /121 Semi-flush bezel for LCD repeater panels 2500/830 & 2500/842 Document Ref: Dis4app.doc / Rev Page 5 of 22 Originator MC Checked AC_

6 2.3 Fully Flush Bezel Fixed to the standard cabinet back box in place of the door and sized larger than the back box. Available in polished or brushed brass, stainless steel and painted finishes. c e a d b f 1-4 loop Repeaters Hole Height a 485mm 375mm Hole Width b 435mm 350mm Hole Depth c 144mm 106mm Bezel Height d 518mm 411mm Bezel Width e 486mm 423mm Hinge Protrusion f 20mm 20mm Part No Description 2501/153 Fully-flush painted bezel for Discovery 1-4 loop panel & large repeater panel 2500/844 (painted to customer's specification) 2501/154 Fully-flush stainless steel bezel for Discovery 1-4 loop panel & large repeater panel 2500/844 (brushed or polished) 2501/155 Fully-flush brass bezel for Discovery 1-4 loop panel & large repeater 2500/844 (brushed or polished) 2501/127 Fully-flush painted bezel for Discovery 1-4 loop repeater panel /830 & 2500/842 (painted to customer's specification) 2501/128 Fully-flush stainless steel bezel for Discovery 1-4 loop repeater panel /830 & 2500/842 (brushed or polished) 2501/129 Fully-flush brass bezel for Discovery 1-4 loop repeater panel /830 & 2500/842 (brushed or polished) Document Ref: Dis4app.doc / Rev Page 6 of 22 Originator MC Checked AC_

7 3.0 Hardware Specifications 3.1 Mechanical Assembly Illustration CHASSIS CABINET MOTHERBOARD DISPLAY LOOP CARDS DOOR POWER SUPPLY PRINTER BATTERY SET (SEE BATTERY CALCULATION SPREADSHEET) Document Ref: Dis4app.doc / Rev Page 7 of 22 Originator MC Checked AC_

8 3.2 User Controls & Indications 20 character by 4 line LCD display. Back-lit when event present or Access controls switch ON. 1 2 EVACUATE SCROLL MESSAGES OVERRIDE DELAY SILENCE BUZZER User indications TEST SILENCE / RESOUND ALARMS ALARMS TEST DISPLAY RESET ACCESS MENU MENU UP ESCAPE < User controls. Only override delay is available without operating the access controls keyswitch 6 MENU DOWN ENTER > Switch to 1 to enable controls (enter level 2). Override delay operates with switch in either position ZONAL FIRE AND FAULT INDICATION Zonal fire (red) and fault (yellow) indications. Pulse to indicate a nonsilenced event, continuous to indicate an event has been silenced Document Ref: Dis4app.doc / Rev Page 8 of 22 Originator MC Checked AC_

9 3.2.1 User Controls and Indications in Detail Operates all sounder circuits continuously Displays the next message at the current event level Activates all alarm outputs when pressed. Alarms silenced when released Tests all indications and internal buzzer Enters the user menu system for access to further level 2 and level 3. Increments digits in user menu number entry EVACUATE SCROLL OVERRIDE DELAY SILENCE MESSAGES TEST BUZZER SILENCE / RESOUND ALARMS ALARMS TEST DISPLAY RESET ACCESS MENU MENU UP ESCAPE < MENU DOWN ENTER > Overrides the delay to outputs function and immediately actions the outputs Silences the internal buzzer for any condition Silence fire events. If already silenced reactivates the previous alarm condition Resets all fire and fault indications. (Fire conditions must be silenced first) Used within access menu to delete items and escape from menus Enters text in the access menus Decrements digits in user menu number entry Indicates power supply active (mains or battery) Constant to indicate delay is active, pulsing when delay running Pulses when a new fire is active, continuous when all fires have been silenced Pre-alarm active Indicates Discovery device drift compensation limit reached Indicates some part of the system has been disabled Indicates internal fault Pulses if new fault detected, continuous if all active faults have been silenced Continuous when the buzzer has been silenced Continuous to indicate some part of the system is in test mode Pulses if fault detected with either alarm circuit or any loop alarm controller. Continuous for a silenced fault and alarm circuit disabled conditions Pulses to indicate another message is available for viewing with the scroll events button Document Ref: Dis4app.doc / Rev Page 9 of 22 Originator MC Checked AC_

10 LK2 S3 S4 LK J1 B1 U4 U3 U2A S1 S2 + J2 I2 J12 J13 J14 J15 FID2 3.3 Engineer s Facilities Fit link to enable earth fault monitoring. Remove link to enable earth fault monitoring. Move switch to right to enable changes to site specific data. Move switch to left to disable when changes complete. LK2 S3 DISABLE SSD WRITE-ENABLE S4 CONFIGURATION SWITCHES LK1 LINK LK2 TO ENABLE EARTH FAULT MONITORING LINK TO DISABLE DISPLAY MONITOR Set switches 1 and 2 for number for loops: Loops loop OFF OFF 2 loop ON OFF 3 loop OFF ON 4 loop ON ON Do not fit link! Lithium battery Auxiliary supply fuse 500mA PC port Cherry keyboard port Alarm 1 fuse 1A Alarm 2 fuse 1A NETWORK REPEATER I/O LOOP 1 LOOP 2 LOOP 3 LOOP 4 LINK LK2 TO ENABLE EARTH FAULT MONITORING A B SCN A B SCN FS4 A B SCN FAULT EVAC. SILENCE RESET 28V 0V NO P FAULT COMPUTER INTERFACE NC NO P FIRE 1 NC NO P FIRE 2 NC + - ALM O1+ O1- I1+ I1- O2+ O2- I2+ ALM 2 I2- O3+ O3- I3+ I3- O4+ O4- I4+ I4- DISABLE SSD WRITE-ENABLE CONFIGURATION SWITCHES KEYBOARD LINK TO DISABLE DISPLAY MONITOR LOOP 1 LOOP 2 LOOP 3 LOOP 4 + SYSTEM FAULT RESET PROCESSOR RESET A1584 INTERFACE 28V 5V 0V MF CF 1 System fault reset Processor reset Loop card 1 position Loop card 2 position Loop card 3 position Loop card 4 position Document Ref: Dis4app.doc / Rev Page 10 of 22 Originator MC Checked AC_

11 3.4 Power Supply PROC BATT L/BATT TEST LAMPS PROC FAULT RESET PSU OK RESET PROC EARTH 5/8V MAIN THERM FAULTS JP2 EARTH FAULT DISABLE SW1 SW2 TEST LAMPS PROC FAULT RESET PSU OK RESET PROC JP1 EARTH CAP DISABLE Document Ref: Dis4app.doc / Rev Page 11 of 22 Originator MC Checked AC_

12 3.5 Use of Auxiliary Inputs Auxiliary inputs are provided to allow remote operation of the following functions: Fault Evacuate Silence Reset Each input circuit is fully monitored for open and short circuit faults. To activate an input a 680 ohm resistor should be connected across the input circuit by a normally open switch contact. Two switches are shown in Figure 1 although there is no limit to the number of switches. INPUT CIRCUIT SWITCH SWITCH END OF LINE 3k9 680R 680R INPUT CIRCUIT Figure 1 Input circuit configuration 3.6 Alarm circuits The Discovery panel has two alarm circuits, each rated at 1A. The circuits are reverse polarity monitored for open and short circuit faults. To allow monitoring all devices must be polarised To prevent damage to the control panel bells must also be suppressed a bell fit diodes as shown in Figure 2. The circuit must be terminated with a 3k9 end of line resistor. ALARM CIRCUIT + POLARISING DIODE (E.G. 1N4002S) SUPPRESSION DIODE (E.G. 1N4002S) END OF LINE 3k9 BELL SOUNDER ALARM CIRCUIT - Figure 2 Alarm circuit configuration Document Ref: Dis4app.doc / Rev Page 12 of 22 Originator MC Checked AC_

13 3.7 Mechanical and Environmental Specification Size: Height: Width: Depth: Weight excluding batteries: Operating temperature: -5ºC to 40ºC Operating humidity: 5% to 95% 480mm 410mm (2 loop and network repeater) 160mm including lock and indented holes 15kg Electrical Mains voltage: 230V AC +10%/-15% Mains failed fault battery current: 1 Loop: 2 Loop: 3 Loop: 4 Loop: Mains failed alarm battery current: 1 Loop: 2 Loop: 3 Loop: 4 Loop: Battery charger type: Maximum battery charging current: Battery type: Battery size: 145mA 170mA 195mA 220mA 260mA 285mA 310mA 335mA Adjustable 27.5V float charger. 1.5A 2 off 12V 12AH sealed lead acid standby battery 151mm x 98mm x 97.5mm Panel inputs Remote Fault: Remote Evacuate: Remote Silence: Remote Reset: Fully monitored circuit, 3k9 EOL, 680R active Fully monitored circuit, 3k9 EOL, 680R active Fully monitored circuit, 3k9 EOL, 680R active Fully monitored circuit, 3k9 EOL, 680R active Panel outputs For each loop: LO+ Loop out +ve LO- Loop out ve LI+ Loop return +ve LI- Loop return ve Alarm circuits 2 at 1A per circuit Auxiliary supply: 500mA Document Ref: Dis4app.doc / Rev Page 13 of 22 Originator MC Checked AC_

14 4.0 Software Specifications 4.1 Overview of Engineers Functions This section describes an overview of the functions available to the end user Changing Time and Date The user can manually set the time and date although this should not normally be required. The current time is maintained by a dedicated battery when all power removed from the system. How to set the time and date is described in the user manual Delay of Operation of Outputs The activation of panel outputs (alarm circuit and cause effect) can be delayed upon detection of an automatic alarm condition to allow for the cause of the alarm to be investigated. The delay can be programmed for a period of between 1 and 10 minutes. The delay is active for one period every day, and off for the remainder of the time. This period is user definable and would typically be during working hours. The delay is not operated if the alarm condition is initiated by a call point or the evacuate function. The delay may be overridden by a user function on the panel. The engineer can set the delay start and end times, set the delay duration and enable or disable the delay Enabling Site Specific Data Changes All site specific data is held in non-volatile memory. To protect this from errors the memory is protected by a write enable switch on the motherboard. This switch has to be set to the write enable position to allow any changes. If the switch is inadvertently left in the enable position when the changes are complete the panel indicates a fault condition Point Configuration The panel loop devices can be automatically reconfigured through an engineers menu command. The panel stores each device address and type on configuration. Any changes to the loop devices are then indicated as a fault. The system configuration can also be printed out. This shows all devices on a loop with their current status. The sensitivity of each point can also be changed to allow for ambient conditions. XP95 detectors can have the trip level for fire and alert configured. Discovery devices have the sensitivity code changed for fire sensitivity and the analogue threshold for alert can be changed. Note: For compliance with EN54 the fire sensitivity level must be set to 55. The pre-alarm value can be set to any value Note: Do not adjust the fire sensitivity level of the XP95 high temperature heat detector. This device has an analogue count of 55 at 90 C. Document Ref: Dis4app.doc / Rev Page 14 of 22 Originator MC Checked AC_

15 Note: The default levels are: XP95 sensor Discovery sensor Default Alert level Default Fire level Valid Alert Levels 35, 40, 45, 50 35, 40, 45, 50 Valid fire levels 55, 60, 65, Default sensitivity levels N/A 3 Valid sensitivity levels N/A 1, 2, 3, 4, 5 All ancillary devices have fixed responses except the Apollo Input Output module. The input for this device can be configured for response as a fire, fault, alert or indication only Discovery Device Functions The following functions are available with Apollo Discovery devices: Print drift compensation level by loop Print device date of manufacture Enable or disable LED pulsing mode Zone Allocation The Discovery has 32 programmable zones. All loop devices can be programmed into one of these zones through the engineers menu. Activation of a fire or a fault on a device will cause operation of the fire or fault indicator associated with the zone. The panel alphanumeric display will also indicate the zone number. The panel has an insert fitted to the front door suitable for text descriptions of each zone location. The engineer can also print out all the zones with the devices allocated to the zones Programmable Cause/Effect Any loop device output can be individually programmed to operate in response to a common event or a zone or group entering a specific condition. The common events are: - Common fire, output cleared on reset Common fire, output cleared on silence alarms Common alert, output cleared on reset Common fault, output cleared on reset Common indication, output cleared on reset Alarms silenced Panel reset Evacuate (including remote evacuate) Document Ref: Dis4app.doc / Rev Page 15 of 22 Originator MC Checked AC_

16 The zone and group based events can occur on any device, or devices within the specified zone or group: - Fire in a group or zone, output cleared on silence alarms. Fire in a group or zone, output cleared on reset. Any two fires in a group or zone, output cleared on silence alarms. Any two fires in a group or zone, output cleared on reset. Alert in a group or zone, output cleared on reset. Fault in a group or zone, output cleared on reset. Indication in a group or zone, output cleared on reset. A group contains device points in the same way as a zone but the group is used solely for cause effect programming. Document Ref: Dis4app.doc / Rev Page 16 of 22 Originator MC Checked AC_

17 4.2 Overview of Engineer s Menu Options Operate Access Controls Key Switch followed by the following: - DISCOVERY PANEL ENGINEERS MENU OVERVIEW ACCESS CODE :USER FUNCTIONS 1: TIME/DATE 2:MODES 1:PANEL DELAY 1:DELAY ENABLE 2:DELAY TIMES 3:DELAY DURATION 2: DAY/NIGHT MODE 1:DAY 2:NIGHT 3:TIMER 4:OFF 3: EN/DIS 1:POINTS 1:SINGLE 2:RANGE 3:VIEW 4:ENABLE ALL 2:ZONES 1:SINGLE 2:RANGE 3:VIEW 3:PRINTER 4:SOUNDERS 4: VIEW 2:ENGINEERS FUNCTIONS 1:PANEL SETUP 1:LOOP SETUP 1:LOOP CONFIGURATION 1:LOOP CONTENTS 1:VIEW LOOP CONTENTS 2:PRINT LOOP CONTENTS 3:RECONFIGURE LOOP 2:POINT SENSITIVITY 1:FIRE 2:ALERT 3:DISCOVERY 1:PRINT DRIFT 2:PRINT DATE 3:LED 4:RAPID COMPENSATION 2:ZONE ALLOCATION 1:EDIT POINT ZONES 2:PRINT POINT ZONES 3:VIEW POINT ZONES 3:LOOP CAUSE EFFECT 1:POINT GROUP ALLOCATION 1:VIEW EVENT LOG 2:VIEW SUPPRESSED EVENTS 5:TEST 1:ALERTS 2:FAULTS 3:INDICATIONS 4:DISABLEMENTS 1:VIEW POINT STATUS 1:POINT DISABLED 2:POINT ENABLED 2:ONE PERSON TESTS 1:EDIT POINT GROUPS 2:PRINT POINT GROUPS 3:VIEW POINT GROUPS 2:LOOP OUTPUT C/E 3:PRINT LOOP O/P C/E 2:I/O SETUP 1:REMOTE EVACUATE MODE 2:TEXT EDIT 1:EDIT COMPANY NAME 2:EDIT POINT TEXT 1:POINT WALK TEST 2:ALARM WALK TEST 6:PRINT 1:CLEAR PRINT QUEUE 2:PRINT EVENT LOG 3:PRINT DISABLEMENTS Document Ref. Dis42app.doc/Rev Page 17 of 22 Originator MC Checked by

18 5.0 Panel Enhancements The Discovery 1-4 loop panel may be enhanced to provide additional facilities. Other relevant documentation is available providing more details. DISCOVERY 1-4 LOOP PANEL A1535 (8 WAY RELAY CARDS) AND A1536 (8 WAY ALARM CARDS) UPTO 31 CARDS PER PANEL REPEATER PANELS ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 KONEX NETWORK REPEATER WITH I/O EXPANSION PC PROGRAMMING ALARM MANAER GRAPHICS SYSTEM Note: This is an illustration only and not wiring schematic. A secondary cabinet is usually required for all PCBs. 5.1 Panel Enhancement Order Codes & Descriptions Part No Description 2500/157 A1535 programmable expansion board - 8 open inputs & 8 relay outputs 2500/158 A1536 programmable expansion board - 8 open inputs & 8 alarm outputs 2500/221 Enclosure c/w 3A psu & space for 6.2AH battery set & 2 or 4 panel programmable expansion boards (A1535 or A1536) 2500/223 Enclosure c/w 5A psu & space for 6.2AH battery set & 2 or 4 panel programmable expansion boards (A1535 or A1536) 2500/107 Printer 2500/198 1A 24V DC door retainer power supply unit in enclosure (no battery back-up) Size - 300h x 350w x 75d 2500/197 MPC1 1A power supply unit in enclosure with space for 3.2AH battery set Size 300h x 350w x 75d 2500/199 MPC3 3A power supply unit in enclosure with space for 12AH battery set Size 355h x 370w x 90d 2500/200 MPC5 5A power supply unit in enclosure with space for 24AH battery set Size 300h x 360w x 190d 2500/201 10A Switch mode power supply unit in enclosure with space for 12AH battery set Size 600h x 380w x 210d Document Ref: Dis4app.doc/Rev Page 18 of 22 Originator MC Checked by

19 5.1.2 A1535/A Way Expansion Boards Up to 31 (A1535 & A1536) 8 way programmable expansion boards may be connected to each Discovery 1-4 loop panel. A special 2 door cabinet is available to house up to 4 enhancement boards (details on request). Up to 31 boards in total may be connected via an RS485 comms - for local expansion only. Local power is required for each board in addition to the RS485 comms link. WARNING: In order to conform to the requirements of BS5839 / EN54, the A way alarm board must be used adjacent to the main panel. The inputs and outputs are fully programmable within the panel s cause/effect facility. The output type (eg relays or alarm circuits) are determined by the board type chosen. The inputs may be monitored or non-monitored, or indication only. Please refer to A Way Relay Board & A Way Alarm Board documentation for further details. 5.2 Battery Sizes (YUASA) Battery Rating 3.2Ah battery 12V 6.2Ah battery 12V 12Ah battery 12V 15Ah battery 12V 38Ah battery 12V 65Ah battery 12V Battery Size 134mm long x 67mm wide x 64mm high 151mm long x 65mm wide x 97.5mm high 151mm long x 98mm wide x 97.5mm high 181mm long x 98mm wide x 167mm high 166mm long x 175mm wide x 125mm high 350mm long x 166mm wide x 174mm high 6.0 Compatible Field Devices Document Ref: Dis4app.doc/Rev Page 19 of 22 Originator MC Checked by

20 The Discovery is approved with the devices listed in this section. The other compatible devices are listed in section 6.1 Approved Field Device Order Codes & Descriptions Part No Description 2501/ Discovery Ionisation smoke detector (Apollo manufacture) 2501/ Discovery Optical smoke detector (Apollo manufacture) 2501/ Discovery Heat detector (Apollo manufacture) 2501/ Discovery Multisensor (Apollo manufacture) 2501/ Discovery Manual call point (Apollo manufacture) 2501/ XP95 Ionisation smoke detector (Apollo manufacture) 2501/ XP95 Optical smoke detector (Apollo manufacture) 2501/ XP95 Temperature detector - standard (Apollo manufacture) 2501/ XP95 Base complete with address card (Apollo manufacture) 2501/ XP95 Manual call point (Apollo manufacture) 2501/ XP95 Isolator (Apollo manufacture) 2501/ XP95 Isolator base (Apollo manufacture) 2501/ XP95 Isolating base, 20 devices (Apollo manufacture) Document Ref: Dis4app.doc/Rev Page 20 of 22 Originator MC Checked by

21 6.1 Other Field Device Order Codes & Descriptions Part No Description 2501/ XP95 Temperature detector - high temperature (Apollo manufacture) 2501/ XP95 Input/Output unit (Apollo manufacture) 2501/ XP95 Output unit (Apollo manufacture) 2501/ XP95 Switch monitor (Apollo manufacture) 2501/ XP95 Switch monitor plus (Apollo manufacture) 2501/ XP95 Zone monitor (Apollo manufacture) 2501/ XP95 Sounder control unit (Apollo manufacture) 2501/ XP95 Mini switch monitor (Apollo manufacture) 2501/ XP95 Mini switch monitor interrupt (Apollo manufacture) 2501/ XP95 DIN rail mounted input/output unit (Apollo manufacture) 2501/ XP95 DIN rail mounted Output unit (Apollo manufacture) 2501/ XP95 DIN rail mounted switch monitor (Apollo manufacture) 2501/ XP95 DIN rail mounted switch monitor plus (Apollo manufacture) 2501/ XP95 DIN rail mounted zone monitor (Apollo manufacture) 2501/ XP95 DIN rail mounted sounder control unit (Apollo manufacture) 2501/ XP95 DIN rail mounted isolator (Apollo manufacture) 2501/ XP95 Loop sounder requires XP95 base (Apollo manufacture) 2501/ XP95 Loop sounder with red cap (Apollo manufacture) 2501/ XP95 Loop sounder with white cap (Apollo manufacture) 2500/229 CEL Addressable break glass unit with back box 2500/236 A1444 basic outstation board (3 inputs) 2500/237 A1445 relay outstation board (3 inputs, 3 relays) 2500/238 A1446 sounder outstation board (3 inputs, 1 sounder circuit, 1 relay) 2500/240 A1447 add-on zone monitor board for above outstation boards 2501/149 Enclosure to fit 1 outstation board; Size - 150h x 225w x 75d 2500/197 Enclosure c/w 1A p.s.e., space for one outstation board & 3.2Ah batteries Size - 300h x 350w x 75d 2500/221 Enclosure c/w 3A p.s.e., space for four outstation boards & 6.2Ah batteries Size - 380h x 600w x 210d 2500/223 Enclosure c/w 5A p.s.e. & space for five outstation boards & 6.2Ah batteries Size - 600h x 600w x 210d 2500/226 Remote square indicator 2500/227 Remote round indicator 2500/232 Loop powered sounder; maximum 16 per loop XP95 RDM Interface (Apollo manufacture) XP95 RDM Ionisation smoke detector (Apollo manufacture) XP95 RDM Optical smoke detector (Apollo manufacture) XP95 RDM Heat detector (Apollo manufacture) XP95 RDM Base (Apollo manufacture) XP95 Loop powered beam detector (Apollo manufacture) XP95 Low power relay base (Apollo manufacture) XP95 Protocol translator single channel (Apollo manufacture) XP95 Protocol translator dual channel (Apollo manufacture) XP95 I.S. Ionisation smoke detector (Apollo manufacture) Document Ref: Dis4app.doc/Rev Page 21 of 22 Originator MC Checked by

22 Part No Description XP95 I.S. Optical smoke detector (Apollo manufacture) XP95 I.S. Temperature detector - standard (Apollo manufacture) XP95 I.S. Manual call point (Apollo manufacture) XP95 I.S. Base (Apollo manufacture) 6.2 General Accessories Order Codes & Descriptions Part No. Description 2501/ mm bell (24 volts DC) 2501/044 Roshni Electronic Sounder (24 volts DC) Deep Base (IP65) 2501/055 Roshni Electronic Sounder (24 volts DC) Shallow Base (IP54 ) 2501/048 Squashni Sounder and Base 2501/049 Cover Plate for Squashni Sounder 2501/056 White Bedhead Sounder 2501/043 Xenon flashing beacon (24 volts DC - 2 watts) 2501/033 Door retainer (24 volts DC) 2501/034 Door retainer (240 volts AC) 2501/035 Door retainer floor bracket Appendices i Other Relevant Documentation Sales Literature Discovery 1-4 Loop Installation and Commissioning Manual Discovery 1-4 Loop User Instructions Wiring Recommendations PC-based Software Programming Guide Battery Calculation spreadsheet Document Ref: Dis4app.doc/Rev Page 22 of 22 Originator MC Checked by