Alarm Security Display Stand Alone C8000 Product Introduction C8000 is a security display stand specially designed for smart phones.this user guide is specifically for mobile retail display
Content Product Introduction- ----------------------------------------------------- 1 Multi-alarm function- ------------------------------------------------------ 2 Installation Installation of security display stand and mobile- ---------------- 3 Indication light under different conditions- --------------------------- 4 Operation of RF remote- ----------------------------------------------- 5-6 Remove exhibit from stand- --------------------------------------------- 7 Specifications- -------------------------------------------------------------- 8 Safety information and cautions- --------------------------------------- 9
Product Introduction Main security sensor Exhibit fixing adhesive Security spiral cable Screw fixing screw LED indication light signal reception of remote control Extra security sensor buzzer base adhesive For mobile cradle Base sensor spiral cable RJ11port Security display stand front Security display stand back Security display stand side 1
Multi-alarm Function Full Protection Multi-alarm function to protect exhibits from theft in all aspects. Alarm activated when the extra security sensor is removed. Alarm activated when the mouse sensor cable is cut off. Alarm activated when the spiral cable is cut off or broken Alarm activated when spiral cable is removed Alarm activated when the security display stand is removed by force Alarm activated when exhibit is removed by force 2 4
Installation of Security Device and Mobile Operation steps: 1-2.Take off the base sticker film and fix the display stand on counter. 3.Take off the mobile surface film and clean the mobile clearly. 4-5.Take off the adhesive film of mobile holder and stick the back of mobile on the holder 6.Take off the extra sensor film and stick it on the front of mobile(notice: avoid covering the mobile camera.) 7.Use the remote control to send signal to the position (shown as the picture)after installation,and press ON to activate the display stand(remote distance 1-6cm) Remark: The environment temperature should be above 10 to ensure the viscosity of sdhesive Adhesive contact surface should be very clean. Press the surface for at least 30 senconds when paste the adhesive. 3
Indication Light Red light blink once Under non-working condition,led light blinks once at the moment the stand base is fixed on counter during first installation. Blink in red LED light blink in red during working condition. alarm LED light blinks rapidly when the stand alarms 4
Operation of remote control LED indication light Turn off device Turn on device/disalarm device Battery position Operation: Turn on device:put or paste the stand on table and make sure of the full contact between base sensor and table,then press ON Stop alarm: Press ON to stop alarm when device alarms and the stand is under working condition again Turn off device: Press OFF to turn off device when alarm is activated. Remark: Point remote towards the small lock position to turn on/turn off the device Remote distance :1-6cm 5
Operation of remote control Battery replacing operations Press the battery cover and rotate it in anti-clockwise direction until it can not be moved. knock on the table and battery comes out replace the battery with + pole upwards put the cover back 6
Remove exhibit from stand Detaching operation: 1.When alarm activated,press OFF on remote to turn off the stand.. 2.Remove the stand from the exhibit counter(during detaching,hard card is recommended to use to insert into the middle of the stand and counter and seperate them by swing. 3.Detach sensor on mobile and pay attention not to scratch the mobile. 4.Separate mobile with mobile holder.(counter(during detaching,hard card is recommended to use to insert into the middle of the stand and counter and seperate them by swing.) Remark:Mobile can be taken from the stand during night or any other situation.when the spiral cable is removed,press OFF to stop the alarm and the mobile can be taken. 7
Specification size others: Alarm valume:100db: 8
Safety information and cautions Please read the following guide carefully to operate the device properly and securely SAFETY WARNINGS Do not dispose of batteries in a fire as they may explode. Dispose of batteries according to local regulations. Please recycle when possible. Do not dispose as household waste. When using alcohol towel, please keep away from heat sources to avoid the cause of fire. ELECTRONIC DEVICE This device is without waterproof protection, when installation should pay attention to the waterproof and moisture-proof. Keep away from the heat sources, and assure the airiness as they may damage the device when overheating. ENVIRONMENTAL PROTECTION Please comply with the local regulations regarding packing materiais and dispose of discarded materials, please recycle when possible. CARE AND MAINTENANCE Take routine testing regularly to find troubleshooting in time to guard against the loss because of the malfunction of alarming. Check the battery power regularly to avoid the malfunction of alarming because of low battery. Do not attempt to open the device other than as instructed in this guide. Do not drop and knock the device. Rough handling can break the internal circuit boards and fine mechanics. Use a damp fine cloth to clean the device, do not use harsh chemicals, like alcohol and cleaning solvents to clean. Do not store the device in hot and cold areas. High temperature can shorten the life of electronic device, damage batteries, and warp or melt certain plastics. When the device returns to its normal temperature, moisture can from inside the device and damage electronic circuit boards. CAUTIONS When alarming please release the device and stop alarming to save power. Keep away from strong interference source, like powerful motor, electric welder, radio transmitter. It can shorten the life of battery. The adhesive is self-adhesive and disposable. Stick it one-time in place. 9