EUROTHERM MASTER COMMUNICATIONS 5000 Series with Master Communications for unsurpassed access to process data everywhere
CONNECTIONS MADE EASY The 5180V, 5100V and 5000B now all support Modbus Master Communications over Ethernet and Serial connections. Powerful features from within the 5000 Series such as user-defined screens, remote access and Auditor Features can now be applied to other areas of the plant. Whether you need to securely record data from other instruments or a centralised HMI for operator use 5000 Series offers you a simple and powerful solution. Product Support The 5000 will recognise other Eurotherm products on the network and autoconfigure parameters for the operator to use. Additional parameters in any instrument can be manually configured. The 5000 Master Communications will support any Modbus device if the instrument is not a recognised profile, the user may manually configure the device offering ultimate flexibility via easy-to-use configuration pages. Autoscan networked devices Master Communications in the 5000 Series is designed for simple connectivity and ease of operator use. The 5000 Master Unit will scan a user-defined selection of addresses and auto-detect devices on the network. HMI Whether the 5000 is being viewed via its local, TFT colour, touch screen display or remotely on a PC or PDA, it offers a range of standard views and the ability for the user to configure a customised view to best suit their application. Some options included are trends, bar graphs, numeric values, mimics, control faceplates and alarm/event views. The 5000 also has powerful Maths and Events functions allowing the user to configure pre-defined actions or buttons. Whether it s driving a relay, popping up a message window or changing the display colour on an alarm the 5000 is designed to give the best information for your process. Serial to Ethernet The 5000 Series supports both serial and Ethernet connectivity. Information from a serial slave device can be read over the Ethernet. The 5000 also support Talk through communications enabling configuration of a slave device over the network through the 5000 e.g. itools running on a PC on the Ethernet network may be used to configure Eurotherm controllers acting as slaves to the 5000. Remote access Using the Bridge 5000 software, all data accessed by the 5000 can be viewed remotely on any PC anywhere on the network. With Full Bridge the user also has full, remote operation and configuration while still maintaining high security and data integrity.
HEAT TREATMENT MADE EASY Vacuum Furnace Carburising Annealing Freeze Dryers The 5000 with Master Communications can be used with Eurotherm control products to give an integrated recording and control solution. The 5180V has a colour, touch screen and provides an excellent HMI for visualisation of the plant. Controller faceplates can be viewed on the recorder enabling the operator to monitor the controllers as well as to change setpoints and other parameters from a single user interface. Bridge software offers complete remote access to the recorder and hence the controllers. Control, Record and Visualise Integrated control and recording Customised plant visualisation Superior security and audit trail functionality Long term, secure data storage Easy set-up and communications Batch functionality Complete configuration of the controllers can be carried out across the network using the PC based itools package. There is no need to change the network or connect directly to the controllers as the 5000s support Talk-through communications enabling the user to access the controllers seamlessly through the 5000. 5180V Customised screens, tailored to meet application needs 12.1 SVGA, touch screen display itools Configuration, monitoring and data logging software Cloning Commissioning OPC Modbus Server 2704 2704 Advanced 3 loop controller Setpoint programming Maths and logic functions Open communications User Interface customisation 2704 3504 2408
POWER GENERATION MADE EASY Nuclear Power distribution CHP Hydro-electric Gas powered Modbus Master Communications on the 5000 Series provides a method of reading and recording up to 96 input channels on a single recorder. Adding control and indication to the same network provides a total solution and flexible centralised HMI. Eurotherm s 2500 DIN Rail I/O offers a distributed, scalable I/O system. It provides high accuracy and plant monitoring using an extensive range of analogue and digital modules. The 5000 Series can auto-scan for the 2500 and has a pre-configured set-up for the unit, making configuration of the system quick and simple. Local and remote I/O Bulk I/O Centralised visualisation Remote monitoring Third party I/O can be manually configured within the 5000 offering the ultimate in flexibility for your system. 5180V 2500 Plug-in modules DIN rail mounting High accuracy Alarm monitoring Advanced PID and logic control SIGNAL CONDITIONERS A full range of Signal Conditioning units is also available from Eurotherm providing distributed, low density I/O. 2408i Universal indicator Temperature, pressure, flow, level Accurate Stable Linearisation functions Alarms THIRD PARTY I/O Any third party I/O supporting Modbus communications can be used for connection to the 5000 Series EUROTHERM SUITE Scalable software solutions Intuitive operation Single tag entry Embedded OPC Online monitoring of continuous and sequential strategies Complete Plant view
FRONT END SECURITY MADE EASY The 5000 takes data security to new levels. The 5000 s Auditor Features are designed in accordance with 21 CFR Part 11. It has unlimited, unique user names with password security. Each user can have individual access permissions and all changes and events are recorded into the embedded audit trail. Electronic Signatures are supported and all data process and Audit Trail are stored in a binary, encrypted format to prevent tampering. The 5000 Series has security systems designed in accordance with 21 CFR Part 11. Using Master Communications, this security can be applied to third party devices providing a secure, centralised Audit Trail. 21 CFR Part 11 Environment Monitoring Steam Measurement 5100V Secure, embedded Audit Trail Electronic Signatures Unlimited, unique user names Mean Kinetic Temperature (MKT) function Time Synchronisation Reaction vessels Autoclaves ph control T640 2404/8 PLC 3216 Micro DCS configurable controller Continuous and sequential functionality Standard control PID cascade/ratio control Advanced control e.g. Boiler blowdown, drum level High stability controllers PID, on/off and motorised valve control Advanced adaptive tuning algorithms 20 setpoint programs Load current monitoring Multi-zone programming Any third party product supporting Modbus communications can be connected to the 5000 Series and make use of its Audit Trail and security functionality. Temp/process controller Alpha-numeric messaging Ethernet enabled Universal inputs
SECURE GATEWAY FOR LEGACY EQUIPMENT MADE EASY Modbus Master Communications on the 5000 Series is easy to use and flexible. Any device using serial or Ethernet Modbus communications can be connected. All 5000 instruments are available with Bridge software. Bridge provides the user with remote monitoring and configuration capability including Modbus functionality. Using the 5000 as a Master on your network, data from connected slaves can be viewed and controlled from any PC, anywhere. The 5000 instruments support both serial and Ethernet communications so data from a serial device can be transferred to an Ethernet network. They also offer Talk-through communications so PC tools for slave devices on the network can be used through the 5000 without the need to change connections. JOIN THE NETWORK Remote monitoring and control Remote configuration Serial to Ethernet conversion Talk through functionality 5000B Remote viewing and configuration Advanced security and Audit Trail DIN rail or wall mounting 13.25Mbyte FLASH memory for process history Up to 12 universal inputs and 84 maths inputs Ethernet and serial communications Bridge Software Bridge Software Seamless interface from Plant floor to PC Remote live monitoring Remote configuration 4103C 1-4 pen continuous chart recorder Universal, isolated inputs 16 event inputs 16 relay outputs Annotation 4250M Six colour, high speed, multipoint chart recorder Up to 96 inputs High speed scanning (all inputs at 1s) 394 Circular chart recorders Up to 6 input channels Annotation Maths functions Totalisers THIRD PARTY EQUIPMENT Any third party equipment supporting Modbus Ethernet or Serial can be connected to 5000 Series and viewed remotely. Process data can be recorded on the 5000 and values monitored or changed either from the 5000 display or remotely using the Bridge software. Maths functions Data storage to PC memory card
CENTRALISED HMI MADE EASY Master communications on the 5000 Series can be used to simply bring information back to a centralised point for ease of operator use. The 5000 provides a Screen Builder facility to enable the user to customise screens to best suit their application from representations of control faceplates to plant mimics. Using the Bridge software these views can be replicated on any PC on the network or, for the ultimate in remote, mobile monitoring, on a PDA device. PDA Remote, live monitoring Remote, full operation and configuration Wireless communication 5180V Customised screens, tailored to meet application needs 12.1 SVGA, touch screen display BRIDGE Full, remote viewing, operation and configuration. 2408i 5000B 5000B 5000B 5000B 5000B 5000B 5000B 3504/3508 Advanced process control Setpoint programming Maths & logic functions Open communications User interface customisation Modular expandable I/O
CONNECTIONS MADE EASY PRODUCT ETHERNET SERIAL MODBUS MASTER MODBUS SLAVE 5180V 5100V 5000B 5100e 2500 2216e 2208e 2204e 3216 2416 2408 2404 3504 3508 2604 2704 2408i T630 T640 4181G 4250G 4103C 4103M 4181M 4250M 4250C 394 Master Product Slave devices Max. input Cyclic write On demand Serial Comms Ethernet Display comms channels outputs write outputs 5180V 16 96 48 48 RS232 / RS485 10BaseT 12.1" SVGA 5100V 16 48 48 48 RS232 / RS485 10BaseT 5.5" _ VGA 5000B 16 96 48 48 RS232 / RS485 10BaseT No Master Product Read / write points Serial Comms Display 2704 100 RS232 / RS422 / RS485 Dot matrix 120-160 pixels 2604 25 RS232 / RS422 / RS485 Dual 5 digit & 2 line LCD EUROTHERM LIMITED http://www.eurotherm.co.uk UK SALES OFFICE US OFFICE Eurotherm Ltd Eurotherm Faraday Close Durrington Worthing 741-F Miller Drive BN13 3PL United Kingdom Leesburg VA 20175-8993 Tel. +44 (0)1903 695888 Fax +44 (0)1903 203767 Tel. 1-703-443-0000 Fax 1-703-669-1300 Email info@eurotherm.co.uk Web www.eurotherm.com Email info@eurotherm.com Copyright Eurotherm Limited 2002 All rights are strictly reserved. No part of this document may be reproduced, modified, or transmitted in any form by any means, nor may it be stored in a retrieval system other than for the purpose to act as an aid in operating the equipment to which the document relates, without the prior written permission of Eurotherm limited. Eurotherm Limited pursues a policy of continuous development and product improvement. The specifications in this document may therefore be changed without notice. The information in this document is given in good faith, but is intended for guidance only. Eurotherm Limited will accept no responsibility for any losses arising from errors in this document. Part No. HA028136 Issue 1 Printed in England 04.03