Car parks Mechanical arms, belts and sheets DETAIL ARM CAR PARK (mm) 5000 Platen 100x5mm Iron sheets 4mm 5000 485 2100 Belts type C 120x50x2 mm 4915 5400 Hot dipped galvanized UNE-EN ISO 1461 or black (without galvanized)
Boards and special profiles Sheets DIMENSIONS FLUTED SHEETS IN BOARDS 2000x1000mm Designation Black Weight (Kgs/M2) Galv. Weight (Kgs/M2) Sheet 3/5 mm 28.00 30.25 Sheet 4/6 mm 36.00 38.90 DIMENSIONS TEARDROP SHAPE SHEETS IN BOARDS 2000x1000mm Designation Black Weight (Kgs/M2) Galv. Weight (Kgs/M2) Sheets 3/5 mm 27.80 29.30 DIMENSIONS SMOOTH PRE-GALVANIZED SHEETS IN BOARDS OF 2000x1000mm Designation Galv. Weight (Kgs./m2) Sheets 0.8 mm 6.30 Sheets 1 mm 7.85 Sheets 1.2 mm 9.45 Sheets 1.5 mm 10.45 Sheets 2 mm 15.70
Boards and special profiles Sheets DIMENSIONS SMOOTH GALVANIZED SHEETS IN BOARDS OF 2000x1000mm Designation Black Weight (Kgs/M2) Galv. Weight (Kgs/M2) Sheet 1.5 mm 11.80 13.00 Sheet 2 mm 15.70 17.30 Sheet 3 mm 23.55 25.44 Sheet 4 mm 31.40 33.92 Sheet 5 mm 39.25 42.40 DIMENSIONS SKIRTING BOARD PROFILE SHEET Designation PB-530 1mm Black Weight (Kgs/M2) 4.67 Galv. Weight (Kgs/M2) 5.15 DIMENSIONS SLIDING GUIDE PROFILE TO EMBED Designation 44x64mm Thickness Material Galv. Weight (Kgs/M2) 3 mm 2.8 Black, pre-galvanized or hot dipped galvanized UNE-EN ISO 1461. Other measures, by request.
Hot dipped galvanized profiles Round and Simple T Designation Black Weight Galv. Weight (Kgs/M.l.) (Kgs/M.l.) Ø 8mm 0.40 0.43 Ø 10mm 0.62 0.67 Ø 12mm 0.89 0.95 Ø 14mm 1.21 1.30 Ø 16mm 1.58 1.67 Ø 18mm 2.00 2.05 Ø 20mm 2.47 2.60 Simple T 30mm 1.80 1.90 Simple T 35mm 2.33 2.50 Simple T 40mm 2.96 3.20 Simple T 45mm 3.67 4.00 Simple T 50mm 4.44 4.90 Simple T 60mm 6.23 6.60 Simple T 70mm 8.32 8.91 Simple T 80mm 10.70 11.45 Hot dipped galvanize UNE-EN ISO 1461 Other measures, by request.
Hot dipped galvanized profiles Platen Designation Black Weight (Kgs/M.l.) Galv. Weight. (Kgs/M.l.) Platen 16x3mm 0.38 0.45 Platen 20x3mm 0.48 0.59 Platen 25x3mm 0.60 0.65 Platen 25x4mm 0.80 0.90 Platen 30x3mm 0.71 0.89 Platen 30x4mm 0.94 1.05 Platen 35x4mm 1.10 1.20 Platen 40x4mm 1.26 1.40 Platen 40x6mm 1.89 2.05 Platen 40x8mm 2.51 2.70 Platen 50x4mm 1.57 1.70 Platen 50x6mm 2.36 2.53 Platen 50x8mm 3.14 3.40 Platen 60x6mm 2.85 3.05 Platen 60x8mm 3.77 4.04 Platen 80x8mm 5.03 5.39 Platen 100x8mm 6.28 6.70 Hot dipped galvanized UNE-EN ISO 1461. Other measures, by request.
Hot-dipped galvanized profiles Angular and belts Designation Black Weight (Kgs/M.l.) Galv. Weight (Kgs/M.l.) Angular 20mm 0.88 1.10 Angular 25mm 1.12 1.30 Angular 30mm 1.36 1.55 Angular 35mm 2.15 2.37 Angular 40mm 2.45 2.66 Angular 45mm 3.48 3.70 Angular 50mm 3.80 4.25 Angular 60mm 5.51 5.80 Angular 70mm 7.50 8.20 Angular 80mm 9.82 10.10 Angular 90mm 12.40 12.50 Angular 100mm 15.35 15.70 Designation Belts Black Weight (Kgs/M.l.) 120x50x2mm Galv. Weight (Kgs/M.l.) 3.70 3.96 Hot dipped galvanized UNE-EN ISO 1461. Other measures, by request.
Hot dipped galvanized profiles UPN and IPN Designation Black Weight (Kgs/M.l.) Galv. Weight (Kgs/M.l.) UPN 40mm 3.00 3.20 UPN 50mm 4.00 4.40 UPN 60mm 5.50 5.70 UPN 80mm 8.90 9.30 UPN 100mm 10.85 11.24 UPN 120mm 13.70 14.00 UPN 140mm 16.30 16.65 UPN 160mm 19.11 20.00 UPN 180mm 22.40 23.20 UPN 200mm 25.70 26.80 IPN 80mm 6.10 6.70 IPN 100mm 8.50 8.90 IPN 120mm 11.30 11.90 IPN 140mm 14.60 15.20 IPN 160mm 18.20 18.90 IPN 180mm 22.30 23.20 IPN 200mm 26.80 27.70 Hot dipped Galvanized UNE-EN ISO 1461. Other measures, by request.
Hot dipper galvanized Light pipe. Rectangular tube Black Weight Galv. Weight (Kgs/M.l.) (Kgs/M.l.) 20x10x1.5mm 0.76 0.83 30x10x1.5mm 0.88 0.97 30x20x1.5mm 1.12 1.25 40x10x1.5mm 1.12 1.25 40x20x1.5mm 1.28 1.40 40x30x1.5mm 1.65 1.82 50x10x1.5mm 1.36 1.62 50x20x1.5mm 1.60 1.75 50x30x1.5mm 1.84 2.00 50x40x1.5mm 2.10 2.30 60x10x1.5mm 1.60 1.75 60x20x1.5mm 1.84 2.20 60x30x1.5mm 2.80 2.30 60x40x1.5mm 2.18 2.40 80x40x1.5mm 2.80 3.10 100x40x2.0mm 4.35 4.70 100x50x2.0mm 4.67 5.10 Designation y x E o x y A Hot dipped Galvanized UNE-EN ISO 1461. Other measures, by request. B
Hot dipped galvanized Light pipe. Square tube Designation Black Weight Galv. Weight (Kgs/M.l.) (Kgs/M.l.) 16x16x1.5mm 0.69 0.75 20x20x1.5mm 0.88 0.95 25x25x1.5mm 1.12 1.25 30x30x1.5mm 1.36 1.50 35x35x1.5mm 1.60 1.75 40x40x1.5mm 1.84 2.00 45x45x1.5mm 2.05 2.25 50x50x1.5mm 2.80 3.10 70x70x2.0mm 4.35 4.70 80x80x2.0mm 4.83 5.20 100x100x3.0mm 9.00 9.60 7.18 7.70 x E Hot dipped galvanized UNE-EN ISO 1461. L o Other measures, by request. x
Sheets and slatted Smooth mesh gates TECHINICAL CHARACTERISTICS Frame made of square tube 1,5 mm and large fender profile. Sidelines pillar for anchorages of doors composed of square tube 100-120 from 3 to 5 mm thick (according to measure). Closure of frame with electro-soldered slatted 60x120 25x3 mm electro soldered mesh 50x150x5 mm or with matching fence material. The sealing system consists of a handle gate with lock.? APPLICATIONS Gate designed to be placed in any metallic enclosure composed of framed panels or without frame. Hot dipped galvanized UNE-EN ISO 1461 or painted polyester galvanized.
Sheets and slatted Smooth mesh gates DIMENSIONS Nominal Panels of gates Opening 1x1.50 m 1 right/left 0,99 m 1,54 m 1x1.80 m 1 right/left 0,99 m 1.83 m 1x2.00 m 1 right/left 0,99 m 2,03 m 2x2.00 m 2 Inside 2,00 m 2,03 m 3x1.80 m 2 Inside 3,00 m 1,83 m 3x2.00 m 2 Inside 3,00 m 2,03 m 4x1.80 m 2 Inside 4,04 m 1,83 m 4x2.00 m 2 Inside 4.04 m 2,03 m 5x2.00 m 2 Inside 5.04 m 2,03 m 6x2.00 m 2 Inside 6.08 m 2,03 m Full width Real height H A B
Modular enclosures Slatted Fences TECHNICAL CHARACTERISTICS It made of ELECTRO-SOLDERED slatted: Mesh 60x120mm Nominal 62x 132mm to axes peaning strength platen 25x2 mm. and smooth round Ø 5 mm diameter Mesh 60x60 mm Nominal 62x66 mm to axes peaning strength platen 25x2 mm. and smooth round Ø 5 mm diameter Set up of platen 40x6mm Post tube 60x60x1,5 mm with metallic stoppers Joins with bolts made of stainless steel Available in three heights 1 mt., 1,5 mts and 2 mts Hot dipped galvanized UNE-EN ISO 1461 or galvanized + painted polyester
Modular enclosures Slatted Fences DETAILS SLATTED FENCE (mm) 2000 1500 1000 2050 DETAILS BOLT SYSTEM (mm) Body-post.
Modular enclosures Mobile fence TECHNICAL CHARACTERISTICS It is made of wire Ø 3 mm., mesh of 150x125 mm. with four reinforcing longitudinal folds of 50x50 mm., to get greater rigidity. Defensive knives located on the top. Side supports of round steel tube Ø 40x1.5 mm. Availability in heights of 1.9 mts. Fixing accessories with quick installation through bolts with nuts M8x20. Base made of reinforced concrete provided with six holes to install any angle. It is strengthened with rib 6 mm to avoid breakages. Weighing about 34 Kilograms. Hot dipped galvanized UNE-EN ISO 1461 or galvanized + painted polyester.
Modular enclosures Mobile fence height panel 1720mm Clamp Electro-soldered mesh 150x100x4mm Post Ø40mm height post 1850mm DETAILS MOBILE FENCE (mm) Concrete base Length panel 3500mm Elevation Folded 1900 3500 Section
Modular enclosures Cerramientos Modulares Folded Grating TECHNICAL CHARACTERISTICS It is made of wire Ø 4.8 mm., mesh of 200x55 mm. with folds to strengthen 50x50 mm. Defensive knives located on the top. Post tube 60x40x1,5 mm. with plastic stoppers on the top. Clamp with plastic stopper is the closure system to hide the bolts. Available in three types of heights, 1, 1.2, 1.5 y 2 mts. Hot dipped galvanized by immersion UNE-EN ISO 1461. Hot dipped galvanized by immersion UNE-EN ISO 1461 + painted polyester. Pre-galvanized. Pre-galvanized + plasticized with polyester. (White RAL 9010 ó Green RAL 6005). Other colours, by request.
Modular enclosures Folded Grating POST 60x40x1.5 mm Total Height CLAMP Nominal Height Number of Posts 1.400 1,000 2 1.500 1,200 2 1.900 1,500 3 2.400 2,000 4 Distance between axes 2515 mm Distance between axes 2515mm 60 panel height 1000 panel height 1200 panel height 1485 panel height 1975 length panel 2500 40 length panel 2500 length panel 2500 panel stoppers length panel 2500 dimensions en mm bolts clamp panel nuts stoppers
Cerramientos Modulares Industrial mesh grating TECHNICAL CHARACTERISTICS It is made of electro-soldered mesh 150 x 50 and wires de Ø 5 mm. Frame made of PDS-26 40 x 44 x 30 X 1,5 mm e. Rectangular tube pilasters 60 x 40 x 1,5 mm. with plastic stoppers on the top. Joins with stainless steel bolts. Available in two heights, 1.5 y 2 mts. Hot dipped galvanized UNE-EN ISO 1461 or galvanized + plasticized with polyester.
Industrial mesh grating DETAIL INDUSTRIAL GRATING (mm) 1620 2070 2820 DETAIL BOLTS SYSTEM (mm) Body-post
Simple torsion enclosure Swing Gates TECHNICAL CHARACTERISTICS Frame made of fender profile PDS 26 40x44x30x1.5 mm. and reinforcing interlayer with rectangular tube # 40X30X1,5 mm. (this reinforcing only exists if the gate has two panels or if it is 2 meters width). Sidelines pillars for gate anchorages composed of square posts # 50, 80 y 100mm, It depends on the sizes of the gates. It has a plastic stopper on the top. Sidelines pillars for gate anchorage composed of square posts # 50, 80 y 100mm, According to the sizes of the gates. They have a metallic stopper on the to. Turning system will have hinges in the gate if this has 4 meters width. The hinges will be adjustable if the gate has more than 4 meters width 4 mts. of width. Closure of frame with electro-soldered mesh 150/50/5 mm. TECHNICAL CHARACTERISTICS The closure system is of type swing. It can be closed not only from inside but also from outside. The pillars will be made of tube # 50x1.5 mm. If the gates has 1 meter wide maximum, # 80x3 mm. If the gate has 4 meters maximum y de # 100x3 mm. If the gate has more than 4 meters width.. The pillars will be made of tube # 50x1.5 mm.. if the gates has 1 meter wide maximum, # 80x3 mm. if the gate has 4 meters maximum y de # 100x3 mm. if the gate has more than 4 meters width.. Hot dipped galvanized UNE-EN ISO 1461.
Enclosures Simple torsion mesh TECHNICAL CHARACTERISTICS It is made of wire Ø 2,20 mm according to UNE 36 738. Mesh size 50 mm. Standard rolls 25 mts., compacted or normal. Heights of 1, 1,5, 1,75 y 2 mts. Outer plastic caps. Three times galvanized 260 grs. Zn/m2. Wire quality G-3B UNE 37-506-83. Packing in loose rolls by units.? APPLICATIONS All types of metallic enclosures. DETAIL SIMPLE TORSION MESH (BASIC) Tensile wire Strut Post Platen Skirting board Skirting board ALIGNMENT POST Skirting board CORNER POST PRINCIPLE POST
Spiral Staircases TECHNICAL CHARACTERISTICS Steps made of plate 3 mm thick. It can be smooth in order for supports of wooden steps, flare drilling 7x20 mm. outdoor, or smooth with rubber pad which can be used not only for outside but also for inside. The steps can be provided with the tube cap of 4" and 100 mm. soldered to join or with notch to solder the tube of 4 and 100 mm. The railings of steps are made of tube 1,5 mm and they can have rails or they can be round without rails. Also forging details can be coupled. The rails and the tops of the railing are made or P.V.C The lengths of the three types of steps are 600, 700 u 800 mm. Hot dipped galvanized UNE-EN ISO 1461, or black (without galvanized).
Plate Steps Rectangular TECHNICAL CHARACTERISTICS It is made of plate 2 mm. Embossed of 14 x 14. The measures of the steps are 600, 800, y 1000 mm. The stair tread measures 250 mm. TECHNICAL CHARACTERISTICS They are made of perforated plate of 2 y 2.5 mm. flare drilling with 15 mm diameter. The measures of the steps are 600, 800 and 1000 mm. The stair tread measures 250 mm. TECHNICAL CHARACTERISTICS They are made of electro-soldered slatted. Mesh 30x30 mm., nominal 34x38 mm. to axes, round. 5 mm diameter and platen of 25x2 mm or 30x3 mm. with non-skid front DIMENSIONS ELECTRO-SOLDERED MESH (mm) 800(direction the platen) x 270 (direction the round) platen 25x2 mm. 900(direction the platen) x 270 (direction the round) platen 30x2 mm. 1.000(direction the platen) x 270 (direction the round) platen 30x2 mm. Hot dipped galvanized UNE-EN ISO 1461, or black (without galvanized).
Plate and slatted Manholes TECHNICAL CHARACTERISTICS PLATE MANHOLES. It is made of plate 2 mm. thickness. Lug for padlock. Hook to catch in work site. Hook to catch in work site Lug for padlock Hot dipped galvanized UNE-EN ISO 1461. TECHNICAL CHARACTERISTICS SLATTED MANHOLES. It is made of slatted mesh 34x38 mm. platen 50x3 mm. and round braided wire 5 mm. or slatted with fluted plate 3,5 mm. Frame support sheet 60x40x3 mm. Dimensions: 500x500 mm. Nominal size Outside Size Inside Size 300x300mm 304x304mm 246x246mm 400x400mm 404x404mm 346x346mm 500x500mm 504x504mm 446x446mm 600x600mm 602x602mm 544x54mm 700x700mm 704x704mm 644x644mm 800x800mm 803x803mm 744x744mm 900x900mm 903x903mm 844x844mm 1000x1000mm 1004x1004mm 947x947mm
Electro-soldered slatted Pieces in stock Mesh Braided Wire Bearing Platen 25x2 mm 30x30 mm. (34X38) 2.000x1.000 mm Ø 5mm 190x1.000 mm Steps 800x270 mm. to support with non-skid front. Mesh Braided Wire Bearing Platen 30x2 mm 3.000x1.000 mm 2.000x1.000 mm 2.000x1.000 mm* 1.000x1.000 mm 30x30 mm. (34X38) 800x1.000 mm Ø 5mm 600x1.000 mm 500x1.000 mm 250x1.000 mm *With security mesh 8x8mm. Steps 900x270 mm. to support with slip front. Mesh Braided Wire Bearing Platens 30x3 mm 30x30 mm. (34X38) Ø 5mm 2.000x1.000 mm Steps 1.000x270 mm to support with non-skid front.
Electro-soldered slatted Horizontal panels DIMENSIONS FOR HORIZONTAL USE (Industrial) (mm) Mesh dimensions 30x30mm (34x38) 30x30mm (34x38) Thick Rib Platen (mm) 5mm Aprox. Weight Aprox. Weight Kgs/m² S/Galv. Kgs/m² Galva. 25x2 13.50 15 25x3 19 21.50 30x2 15.80 17.50 30x3 24 26.70 35x3 26 29 40x3 29 32 50x3 38.20 41.30 60x4 61.50 66.50 30x2 21.80 24.40 30x3 30 33.60 5mm WITH SECURITY MESH Panel 6.100mm Length ; Panel 1.000 mm Width DIMENSIONS FOR VERTICAL USE ( Decorative) mm Mesh Dimensions Thick Rib Platen (mm) 6.100 Aprox. Weight Aprox. Weight Kgs/m² S/Galv. Kgs/m² Galva. 1.000 60x120mm (62x132) 25x2 7.60 8.60 25x2 8.70 9.85 5mm 60x60mm (62x66) Panel 6.072mm Length; Panel 1.862 mm Width Hot dipped galvanized UNE-EN ISO 1461 or black (without galvanized) APPLIANCES Pieces to support slatted mesh 34 mm. (hot-dipped galvanized)
Electro-soldered slatted Electro-soldered mesh Mesh Dimensions 100x50mm Thick Rib 4mm Kg/m² Grey 2.80 Kg/m² Pre-Galv. Kg/m² Hot-Dip 2.88 3.20 Panel 2.600mm Length; Panel 1.500 mm Height 2.000 mm Mesh Dimensions 150x50mm Thick Rib 5mm Kg/m² Grey 3.96 Kg/m² Pre-Galv. Kg/m² 4.06 4.55 Panel 2.600mm Length; Panel 1.500 mm Height 1.950 mm Mesh Dimensions 50x50mm Thick Rib 4-5mm Kg/m² Grey Kg/m² Pre-Galv. Kg/m² Hot-Dip 4.06 4.14 4.67 5.48 5.60 6.00 Panel 2.600mm Length; Panel 1.500 mm Height 2.000 mm
Electro-soldered slatted. Finished pieces in stock Gutters TECHNICAL CHARACTERISTICS It is made of electro-soldered slatted mesh 30x30 mm. nominal 34x38 mm. to axes, round braided wire Ø 5mm. and platen bearing platen 25x2. Frame to support 30 mm. in angular with hook to catch in work site.? APPLICATIONS It is designed to collect water and for the traffic car. The grille 30x30 25x2 is situated in sections of 1.000 mm. (direction the round) X 190 (direction the platen). The grille 30x30 30x2 in sections of 250 (direction the platen) x 1.000 mm.. Bearing frame in L-30 mm situated in sections of 2015 and 1000 mm length x 205 mm width. Hot dipped galvanized UNE-EN ISO 1461.
Hot dipped Galvanized Sliding gates TECHNICAL CHARACTERISTICS Frame made of square tubes of 2 and 3 mm width and skirting board with corrugated sheet. It allows the gate automation. Closure of frame with electro-soldered slatted 60x120 25x3 mm., electro-soldered mesh 50x150x5 mm. or with matching fence material. Clamping bridges are made or square tube of 80x2 or 3 mm (according to measure). The rolling guide is made of IPN profile and round Ø 18 mm. Silent sliding by means of nylon bearing in the bridges. All components of the gates, the rolling guide included, are hot dip galvanized.? APPLICATIONS This gate is designed to be situated in any metallic enclosure formed with framed panels or without frame.
Hot dipped Galvanized Sliding gates Hot dipped galvanized UNE-EN ISO 1461 or Galvanized + Painted Polyester. DIMENSIONS (m) Nominal Width Step (A) Height 4x2.20 m 4.02 m 2.20 m 4.55 m 5x2.20 m 5.04 m 2.20 m 5.55 m 6x2.20 m 6.05 m 2.20 m 6.65 m 8x2.20 m 8.08 m 2.20 m 8.65 m 10x2.20 m 10.12 m 2.20 m 11.15 m 12x2.20 m 12.15 m 2.20 m 13.20 m Space Opening Gate 2200 A
Senzimir galvanized Sliding gates TECHNICAL CHARACTERISTICS Frame made of senzimir galvanized tube 60x40x1.5 mm. and skirting board with galvanized sheet 2 mm. with boreholes of 30x30 mm. Closure of frame with electro-soldered galvanized mesh in wire Ø 5 mm. de 200x50x5 mm., with four reinforcement folds 50x50 mm. Clamping bridges are made of senzimir galvanized tube 60x40x1.5 mm. Rolling guide is made of profile to embed 40x64x3 mm. thickness. Silent sliding by means of nylon bearing in the bridges.? APLICATIONS This gate is designed to be situated in any metallic closure formed with framed panels or without frame. Senzimir galvanized or galvanized + painted polyester.
Sheets and slatted Smooth slatted gate DIMENSIONS (m) Nominal Width Step (A) Height Space Openin Gate 4x2.00 m 4.04 m 2.10 m 4.55 m 5x2.00 m 5.04 m 2.10 m 5.55 m 6x2.00 m 6.08 m 2.10 m 6.60 m 7x2.00 m 7.08 m 2.10 m 7.70 m Senzimir galvanized or galvanized + painted polyester.