FortiGate/FortiWiFi 70D/90D Performance Consolidation Protection
February 19, 2014 01-500-199105-20140219 Copyright 2014 Fortinet, Inc. All rights reserved. Fortinet, FortiGate, and FortiGuard, are registered trademarks of Fortinet, Inc., and other Fortinet names herein may also be trademarks of Fortinet. All other product or company names may be trademarks of their respective owners. Performance metrics contained herein were attained in internal lab tests under ideal conditions, and performance may vary. Network variables, different network environments and other conditions may affect performance results. Nothing herein represents any binding commitment by Fortinet, and Fortinet disclaims all warranties, whether express or implied, except to the extent Fortinet enters a binding written contract, signed by Fortinet s General Counsel, with a purchaser that to performance in the same ideal conditions as in Fortinet s internal lab tests. Fortinet disclaims in full any guarantees. Fortinet reserves the right to change, modify, transfer, or otherwise revise this publication without notice, and the most current version of the publication shall be applicable.
Register for Support Register your Fortinet product to receive: Technical Support New product features Protection from new threats Debe registrar el producto para recibir: Apoyo técnico Nuevas funcionalidades del producto Protección contra ataques Vous devez enregistrer le produit pour recevoir: Support technique Nouvelles fonctionnalitées du produit Protection contre de nouvelles menaces La reistrazione ti permette di usufruire di: Supporto Tecnico Nuove funzionalita Proteezione dalle ultime minaccce FortiGate/FortiWiFi 70D/90D QuickStart Guide http://forti.net/support Toll free: 1 866 648 4638 Phone: 1 408 486 7899 Fax: 1 408 235 7737 Email: register@fortinet.com
Box Includes Before You Begin Performance Consolidation Protection W AN 1 1 3 5 7 9 11 13 W AN 2 2 4 6 8 10 12 14 Write down details that you may need from your network administrator or ISP. CONSOLE POWER STATUS ALARM HA WIFI FortiGate/FortiWiFi 70D/90D USB Cable DSL PPPoE Cable Modem DHCP Username It is normal to not require a hostname but your ISP may require it. Password Hostname Ethernet Cable T1/E1, Static broadband, Cable, or DSL with a static IP Power Cable 2 Wireless Antennae (Wireless models only) 4 Power Adapter (Ground lug on PoE models only) IP Address Subnet Mask Default Gateway Primary/Secondary DNS QuickStart Guide Video http://forti.net/vqsg 5
1 WAN1 Internet A LAN port 1 Power Connection Ground Screw Basic Connections https:// 1. Connect your device to a power outlet and an Internet connection. This is usually a modem, but could also be another device on your network. 2. PoE models only: connect the ground lug to the device ground screw. 2 FortiGate Setup Options Web Browser with Ethernet cable A Web Browser B OS X Web-based Manager 6 C Setup Wizard (p.7) Terminal Emulation (p.10-11) D With FortiExplorer (pp.8-9) (pp.12-13) 1. Connect the Ethernet cable. 2. Visit 192.168.1.99 in your web browser. 3. Login using username admin and no password. 4. Click Wizard in the top right corner. 5. and save your settings. 6. Register your device from the dashboard page. 7
B USB MGMT Windows/OS X with USB 1. Download FortiExplorer from http://forti.net/fexp. Microsoft Windows Install Mac OS X Install FortiExplorer Setup Wizard 8 2. Connect the USB cable and launch FortiExplorer if it does not appear automatically. 2. Double-Click the and drag the FortiExplorer icon to the Applications folder. 3. Connect the USB cable. 4. Click the FortiExplorer icon to launch the application. 1. Follow prompts or click Register to register your device with FortiCare. 2. Click Setup Wizard. 3. Login using username admin and no password. 4. Follow Setup Wizard steps. 5. Click to complete the setup of your device. 9
C Terminal Emulation with Console Cable To Connect to the CLI (Console Models Only) 1. Connect the FortiGate unit console port to the management computer using a standard console cable (not provided). 2. Start a terminal emulation program on the management computer. Select the COM port and use the following settings: Baud Rate: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow Control: None 3. Press Enter on your keyboard to connect to the CLI. 4. Login using username admin and no password. You can now proceed with A list of commands can be found at http://forti.net/cli. Get started by typing? for a list of available commands. Begin typing a command and type? for a list of available ways to complete. For example A comprehensive reference guide with all commands can be found at http://forti.net/cli. 10 11
D USB Port iphone/ipad/ipod Touch with Apple to USB cable FortiExplorer App http://forti.net/fexp-ios 12 1. Download the ios FortiExplorer App to your device from http://forti.net/fexp-ios. 2. Use your Apple USB cable to connect to the USB port. 3. Launch the FortiExplorer App and select the device model. 4. Login using username admin and no password. 13
Alarm Red: Major Amber: Minor Off: None Status Flashing green: Booting up Green: Normal PWR Green: On Off Wireless models only HA Green: Operating Off: Disabled WiFi (Wireless models only) Green: Connected Off: No connection USB MGMT (USB mini-b) USB (USB A) Device Guide FortiGate/FortiWiFi 70D/90D Non-PoE Models Only LAN Ports 1-14 (RJ-45) Gigabit Ethernet 14-port switch connection for the internal network 13 11 9 7 5 3 1 WAN1 W AN 1 1 3 5 7 9 11 13 USB CONSOLE POWER STATUS ALARM HA WIFI W AN 2 2 4 6 8 10 12 14 DC+12V USB MG MT 14 12 10 8 6 4 2 WAN2 Console (Console models only) Optional connection to the management computer. Provides access to the CLI WAN 1 & 2, LAN Ports 1-14 Green: Connected at 1Gbps Flashing green: Transmitting & receiving data at 1Gbps Amber: Connected at 10/100Mbps Flashing amber: Transmitting & receiving data at 10/100Mbps Off: No link established Power Connection 12V DC, 2.5A 100-240V AC, 50-60Hz adapter WAN 1 & 2 (RJ-45) Internet 14 15
HA Green: Operating Off: Disabled Status Flashing green: Booting up Green: Normal PWR Green: On Off Wireless models only WiFi (Wireless models only) Green: Connected Off: No connection PoE Status Green: Power delivered Flashing green: Error/fault Off: No power delivered Power Connection 48V DC, 2.5A 100-240V AC, 50-60Hz adapter Attention: The power adapter ground lug must be connected to the device ground screw. USB MGMT (USB mini-b) Device Guide FortiGate/FortiWiFi 90D PoE Models Only Internet CONSOLE W AN 1 1 3 5 7 9 A C A C USB (USB A) WAN 1 & 2 (RJ-45) POWER STATUS ALARM HA WIFI W AN 2 2 4 6 8 10 B D B PoE D C A 9 7 5 3 1 WAN1 USB Console (Console models only) Optional connection to the management computer. Provides access to the CLI. Alarm Red: Major Amber: Minor Off: None WAN 1 & 2, LAN Ports 1-10 & A - D Green: Connected at 1Gbps Flashing green: Transmitting & receiving data at 1Gbps Amber: Connected at 10/100Mbps Flashing amber: Transmitting & receiving data at 10/100Mbps Off: No link established 16 17 DC+48V USB MGMT D PoE B 10 8 LAN Ports 1-10 (RJ-45) Gigabit Ethernet 14-port switch connection for the internal network LAN Ports A - D (RJ-45) Gigabit Ethernet ports with Power over Ethernet (PoE) up to a maximum 15.4W for each port 6 4 2 WAN2
More Information FortiGate Cookbook Advanced installing and setup, networking, security policies Training Services Cours CLI Reference li FortiOS Handbook 18
Cautions and Warnings Operating Temperature Température ambiante élevée 0 à 40 C (32 à 104 F) Si cet appareil est installé dans un cabinet fermé, la température ambiante du cabinet peut être supérieure à Storage temperature -35 to 70 C (-31 to 158 F) 35 à 70 C (-31 à 158 F) Humidity 20 to 95% non-condensing Humidité 20 à 95% sans condensation Operating altitude < 2250 m (7380 ft) Altitude opérationnelle <2250 m (7380 pi) Ventilation refroidissement adéquat. Circuit overloading might have on current protection and supply wiring. For redundant power sources, connect each to an IEC/UL Listed power source whose output rating is greater than or equal to the equipment. Surtension Reliable earthing Make sure all rack-mounted equipment is grounded. This includes supply connections (e.g. power strips), not only direct connections to the branch circuit. Mise à la terre des connexions directes au circuit de dérivation. Interference If possible, use Shielded Twisted Pair (STP) Ethernet cables instead of Unshielded Twisted Pair (UTP). Interférence Safety Mechanical loading To avoid personal injury or damage to the appliance, Fortinet recommends that 2 or more people together install the appliance into the rack. Balance the equipment to avoid uneven mechanical loading and tipping. Do not place heavy objects on the appliance. Installation To avoid risk of damage to your equipment, personal injury, or death, disconnect cables while servicing. Do not connect or disconnect cables during lightning. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Do not install this equipment in a home or public area accessible to the general population. When installed in schools, this equipment must be installed in a location where access is restricted to trained personnel. Battery your local regulations. IMPORTANT: Switzerland: Annex 4.10 of SR814.013 applies to batteries. Batterie IMPORTANT: Grounding To prevent damage to your equipment, connections that enter from outside the building should pass through a lightning / surge protector, and be properly grounded. Use an electrostatic discharge workstation (ESD) and/or wear an anti-static wrist strap while you work. In addition to the grounding terminal of the plug, on the back panel, there is another, separate terminal for earthing. Mise à la terre / parasurtenseur et sont correctement mis à la terre. Utilisez un poste de travail de décharge électrostatique (ESD) et / ou portez un bracelet anti-statique lorsque vous For products with power over Ethernet (PoE): Power over Ethernet (PoE) Do not connect this device to PoE networks with routing to the outside plant. Use this equipment in a Network Environment 0 per IECTR 62101. Do not use PoE injectors that are not IEEE 802.3af compliant. They may damage your device. Alimentation par Ethernet Ce matériel doit être utilisé dans un Environnement Réseau 0 par IECTR 62101. Ce matériel est uniquement connecté aux réseaux PoE Regulatory Compliance Federal Communication Commission (FCC) USA This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. WARNING: equipment Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For FWF product model: Caution: Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Industry Canada Equipment Standard for Digital Equipment (ICES) Canada CAN ICES-3 (B) / NMB-3 (B) This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. un minimum de 20 cm de distance entre la source de rayonnement et votre corps. For FWF product model: Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Avertissement: brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars causer du brouillage et/ ou des dommages aux dispositifs LAN-EL. This device has been designed to operate with an antenna having a maximum gain of 2dBi for 2.4GHz and 3dBi for 5GHz. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de 2dBi pour 2,4 GHz et 3dBi pour 5GHz. Une antenne à gain plus élevé est satisfaisante. European Conformity (CE) - EU This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. For FG product models: For FWF product model: National Communications Commission (NCC) Taiwan For FWF product model: