SAUDI YANBU PETROCHEMICAL COMPANY FINAL ADVERTISEMENT TEXT 2015 NON-SAUDI RECRUITMENT FOR VARIOUS POSITIONS Inspection & Corrosion / (2) Inspection Engineer B.S Degree in Material or Mechanical Engineering. A minimum of 8 years extensive experience in inspection and corrosion monitoring & control activities of static equipment in petrochemical processes. Candidates should be certified on API 510, API570 or API 653. Level II in NDT, AWS, RBI, Coating, and any other certificates related to Inspection are preferred. Anf Good spoken and written English, and Reporting skills, Good communication skills. Saudi Yanbu Petrochemical Company (YANPET) seeks an experienced Senior Inspection engineer. The engineer will be part of the Asset Integrity Management Department responsible Performs Inspection and Testing services covering Corrosion Monitoring and Protection activities to assure safe and efficient operation at all stationary equipment. Rotating Equipment / (2) Extruders System and Gear Box Engineer University Degree in Engineer, Minimum of (8) years experience in Plant Maintenance, Operations, Support Services or Engineering. Speaks English very good. Minimum (8) years experience in Petrochemical plant s Maintenance/ Engineering/ and technical support. Operational & Reliability management experience are preferred. Provide technical support services in area of Rotating Equipment related to Extruders and Gear Boxes in Yanpet. Electrical Support / (1) Sr. Engineer L/H Voltage Switchgear & Transformer Bachelor of Science in Electrical Engineer, Minimum of ten (8) years (Last three years of experience on L/H Voltage Switchgear &Transformer). Good knowledge in English, SAP Knowledge. The L/H Voltage Switchgear & Transformer Engineer primary role is to develop and implement an asset integrity assurance and verification, by establishing and developing equipment strategies / assessment for L/H Voltage Switchgear & Transformer equipment. The L/H Voltage Switchgear Engineer will also provide a high-level technical support to resolve unstructured complex failures in all type of electrical equipment and systems.
Electrical Engineer / (1) Sr. Engineer System Protection Bachelor of Science in Electrical Engineer, Minimum of ten (8) years (Last three years of experience on protection System). Good knowledge in English, SAP Knowledge. The System Protection Engineer primary role is to develop and implement an asset integrity assurance and verification, by establishing and developing equipment strategies / assessment for Protection System and equipment. The System Protection Engineer will also provide a high-level technical support to resolve unstructured complex failures in all type of electrical equipment and systems. Instrument Support / (1) : Sr. Engineer SIS Bachelor of Science in Electrical Engineer Technology, Good knowledge in English, SAP Knowledge. Minimum experience (8) years. With experience in ESD System and Field Instrument. Also TUV functional safety certified or equivalent, and PHA certified and Meridium knowledge. With PC skills, leadership skills, communication skills. To conduct SIL study, assessment, validation and verification for instrument loops Senior Process Engineer U&O B.S. in Chemical Engineering with minimum twelve (12) years in Petrochemical or Refinery Operations as technical process engineer at utilities and offsite field. Ability to communicate in English and capable of writing English clearly. Knowledge of cooling water/ seawater plate & frame exchangers operation and performance. Specific operational knowledge and experience in Air separation and Boilers Plants. Knowledge of wastewater treatments different facilities and technologies. Ability to identify and follows up and lead on short/long-term projects such as plant debottlenecking projects and plant expansion studies. Preferred to have knowledge and experience in commissioning and start up activities. He should have strong technical background and ability to perform engineering calculation and dealing with process simulation tools using PROII & INPLANT with familiarity of design Methods and different technologies and Practices. He should be familiar with Process Controls & Protective System Design
Process Control Engineer B.S. in Chemical Engineering with five years experience as Process Control Engineer. Preferable experience on Polymers (HDPE/PP) or Ethylene Glycol plant. At least two years experience as Process/Operation Engineer. Should have a very good experience in dealing with Honeywell DCS system (TPS system with Experian HMI/Servers). Should have a good knowledge and ability to perform basic controllers tuning (on Honeywell System), do plant troubleshooting, and develop DCS applications to provide reporting/alarming and sequential control. Ability to use Process Control assistive tools, such as Alarm Management Systems, Controller Performance Management, OSI PI system etc. Preferable experience in APC systems: Pavilion, AspenTech DMC and Honeywell APC. Good PC skills, MS office as minimum Process Safety Senior Engineer B.S. in Chemical Engineering with 15 to 20 years experience in Process, operation and process design in petrochemical or Refinery plant. Minimum of 4 years experience in operation, 5 years in Process Engineering and 2 years in process design Possess experience in safety engineering technologies including: *Risk Assessment and Management *Process Hazard Analysis*Capital Project Safety Reviews *Pressure Relief Systems / Flare Design *Building Blast Evaluations *Pre-Start-up Safety Reviews *Human Factor Analysis *Fire Protection Technology *Safety Critical Devices (Safety Instrumented Systems) *Dispersion Modeling Analysis and tools such as PHAST *Safety Critical Procedures such as energy isolation, opening process equipment, and inert entry Incident Investigation *Root Cause Analysis *Safety-related government and industry standards. *Strong technical background and ability to identify the Hazards & credible scenario and perform engineering calculation as well as dealing with process simulation tools such as PHAST.*Good
leading & English skills. Polymer Reaction Senior Engineer PE/PP B.S. in Chemical Engineering with Eight-Ten years experience in HD Polyethylene and/or Polypropylene in Polymer Synthesis (Reaction) area. Minimum of 4 years experience in Process Engineering. Should have a very good experience in big scale Polymer Reactor, 20 t/h and plus. Should have excellent knowledge and know how of polymerization (Unipol Gas Phase Technology) and understanding of PE/PP properties and characteristic. Strong technical background and ability to perform engineering calculation and dealing with process information system tools such as PI. Good PC skills, MS office as minimum. Polymer Extrusion Senior Engineer PE/PP B.S. in Mechanical Engineering with Eight-Ten years experience in HD Polyethylene and/or Polypropylene in Polymer Extrusion ( Finishing ) area. Minimum of 4 years experience in Process Engineering. Should have very good experience in big scale Polymer Extruder, 20 t/h and plus. Should have excellent knowledge and know how of HD Polyethylene and/or Polypropylene blending, compounding & pelletizing,. Excellent experience in Extruders machines KOBE and/or Coperion WP Extruders. Strong technical background and ability to perform engineering calculation and dealing with process information system tools such as PI. Good PC skills, MS office as minimum.
Project Development Engineer BS. Degree in Mechanical, or Electrical or Chemical Engineering; Minimum of 7-8 years of experience in Project Management in the oil & gas or petrochemical industry. Coordinates engineering work from the conceptual deign to the final commissioning and handover to the user. Includes developing and obtaining approvals of design drawings and material requisitions, coordinating the procurement and inspection of equipment and material, overseeing construction activities and following through to commissioning and handover to the user. Manage assigned projects scope, cost, schedule, quality, procurement, communications, risk, and integration. Process Design Engineer (Glycol & Polymer) BS. Degree in chemical engineering; Minimum of seven - years of experience in Process Engineering in the oil & gas or petrochemical industry. Leads the process of project ideas initiation and screening in the Derivatives Process Plants (Glycol & Polymer). Develops process design packages for the selected ideas of modifications in the Plants/equipments, of new facilities inside battery limits (ISBL), or outside battery limits (OSBL). Provides technical support to project & MOC development throughout different phases. Participates in process studies for proposal related to plant improvements. Lead PPHA and participate in the assigned Process Hazardous Analysis studies. Ability to perform engineering calculation. Dealing with process simulation and tools. Basic knowledge of safety rules and process safety best practices. Familiar with International (API, NFPA, ASME etc.) Engineering Codes & Standards.