EV-604 Vehicle GPS Tracker

EV-604 Vehicle GPS Tracker EV-604 User Guide V2.0-1 -

1, Product Overview Thank you for using EV-604 Vehicle GPS Tracker. It s equiped with Quad Bands GSM/GPRS module, Hi-sensitivity U-blox GPS receiver, 8MB flash memory. The fuel detecting and anti-jamming function will bring u more options for security purpose. EV-604 supports both GPS tracking and GSM Network Station tracking, which brings you a idea solution with 7-24 position fix with no blind area for locating your mobile objects. It can work alone without any third party help, but also could integreate to a monitoring center base by SMS query or TCP connection query. What s New? Tracking by GPS satellite and GSM base station (Double-Positioning) GSM Anti-jamming Detection Two way voice communication Support fuel detection Support external power voltage detection GPS antenna cut alarm Built in 8MB flash memory GPRS blind area data re-upload to server. Firmware upgrade over the air. - 2 -

2, Getting Start, Please follow me! 2.1 Hardware and Accessories: EV-604 is supplied in a box which includes: EV604 with back-up battery GPS Antenna GSM Antenna 12pin cable Relay Microphone - 3 -

2.2 View GSM LED (Green) Dim for 5 times Flashing(every 3 seconds) Flashing(every 0.1 second) The unit is being initialized EV604 is connected to the GSM network EV604 is not connected to the GSM network GPS LED (Yellow) Dim for 5 times Flashing(every 3 seconds) No flashing The unit is being initialized EV604 has a GPS fix EV604 has no GPS fix - 4 -

2.3 Connection and Installation: Your GPS Tracking Device can be installed quickly and easily by a qualified Auto Electrician. 2.3.1 Ensure that your EV604 has a working SIM installed. Test before replacing all paneling. Check the SIM card has not run out of credit. please ensure pin number on SIM card is disabled. Install the SIM card. Press yellow button to eject the SIM card holder and put SIM card on SIM card holder. Insert the SIM card holder to the device correctly. 2.3.2 Connect GSM&GPS antenna. Connect the GSM antenna to EV604. The GSM antenna comes in two parts. They must be firmly screwed together to receive a strong signal. This antenna is not all weather but it can receive a signal through metal. A good position for this antenna is to run the wiring behind the corner post of the vehicle and locate the antenna in the hood lining behind the sun visor. Once again only screw wiring to device by hand as damage could be caused by the use of a spanner. Connect the GPS antenna to EV604. The GPS antenna is an all weather unit and is magnetized for easy attachment. The signal for the GPS cannot penetrate steel, only plastic so the GPS antenna must be located in an open position. The best location is under the plastic - 5 -

panel near the windscreen wipers or on the inner panel near the hinge of the hood. The lead from this antenna needs to go through the fire wall and screw to the device firmly by hand only (Do NOT use a spanner or similar device). 2.3.3 Inputs and outputs cable connections must be firm and reliable. The unused electrical wire should be probably insulated. 2.3.4 Connect the 12pin cable to EV604. Input power: 6-30VDC (With polarity protection The system won t be damaged by wrong polarity input but it won t work) 2.3.5 The device should be installed in a position where it cannot be detected. A suitable position is to mount the device around the steering column under the dashboard secured by two cable ties. Wherever you locate the device it should be kept dry, away from excess heat and subject to minimum vibration. 3 Usages 3.1 GPS information. The GPS INFO means: DATE: 08-09-26(YY/MM/DD); TIME: 15:33:26(HH/MM/SS); LAT: 22.21326446N; LOT: 113.45199584E; Speed: 000.0-6 -

3.2 To set the Authorized Number It is not mandatory for all three of the authorized numbers to be set, however a minimum of one must always be set. Set up the 3 authorized mobile phone numbers to track the device. 1 Command: Password +A +1 Example: 123456A1 (Default Password: 123456) Using your mobile phone, send the following text message to the SIM card phone number: The letter A in caps lock followed by 1 (1 is the code used to register the phone number of the SIM card used to send the SMS), with no spaces in the text, After sending SMS command to the device, it will reply you a message with following informations: 1 TEL. OK! +GPS INFO To delete this number from stored memory, you can send password+a+0 to the tracker. 2Command: Password +B+1 Note: B must be in capital form. Example: 123456B1 The device will reply you a message with following information: 2 TEL. OK! +GPS INFO To delete this number from stored memory, you can send password+b+0 to the tracker.. 3Command: Password +C+1 Note: C must be in capital form Example: 123456C1 The device will reply you a message with following information: 3 TEL. OK! +GPS INFO - 7 -

To delete this number from stored memory, you can send password+c+0 to the tracker. Only Number A can delete all the three numbers. Number B and C can delete themselves but cannot delete Number A. 3.3 Change password: Command: Old password + H + new password Example: 123456H666666 Note: H must be in capital form, send it to EV604 to change your password. The password now is changed to 666666 The pre-set password won t be erased by changing a new sim card. Be sure keep the new password in mind, otherwise you have to ask your distributor to restore the original setting in case of losing the new password. Make sure the new password is in 6 digits, or else the tracker can not recognize the password. 4. Modify the Time zone: Command: Password+L+ +00/-00 Note: the time must amounts be in 2 digits and at maximum 23 hours in value. + in the time zone portion of the text indicates east. The symbol - in the time zone indicates west. Example: 123456L+02, the system will add 2 hours based on the UTC time. 123456L-02, the system will minus 2 hours based on the UTC time. Default time of the tracker is UTC time. 5. Add user name in SMS content: Command: Password+U+1, user name - 8 -

Note: U must be in capital form, send it to EV604 to add user name in SMS content. Example: 123456U1,Mazad, the tracker will reply Mazad+GPS info!xxxxxxxx 6. Locate the car position: 6.1 Track on Demand- Reply with Latitude, Longitude. Command: Password +F Note: F must be in capital form, send it to EV604 to acquire GPS information. Example: 123456F The device will reply GPS Info! Date: xxxxxxx; Time: xxxxxxxxx; LAT: xxxxxxxxxx; LOT: xxxxxxxxxx; Speed: xxxxxx Put position latitude and longitude to Google earth or Google maps. Click on search button, then you will find the position fixed. - 9 -

6.2 Track on Demand- Reply with Coordinates and Web Link. Command: Password +FM Note: FM must be in capital form, send it to EV604 to acquire Location Link. Example: 123456FM The device will reply Date: xxxxxxx; Time: xxxxxxxxx; LAT: xxxxxxxxxx; LOT: xxxxxxxxxx; Speed: xxxxxxkm/h; http://maps.google.com/map?q=22.6487882,114.030380&hl=en&t=m&z=16 Click on the link then the location can be shown directly on Google Map on your mobile phone. - 10 -

6.3 Track on Demand- Reply with Coordinates and Real Address. Command: Password +ADD Notes: ADD must be in capital form, send it to EV604 to acquire real address. This Function needs GPRS function support! Example: 123456ADD The device will reply LAT: xxxxxxxxxx; LOT: xxxxxxxxxx; Add: Donghuan 1 st road, Bao an, Shenzhen,Guangdong,China; - 11 -

6. Track by GSM base station tower The unit can be tracked by GSM base station tower, If GPS signal is not available for example in room, underground etc, user are able to locate by GSM tower. However, as compared to GPS satellite, GSM accuracy is proven to be worse than that of GPS. GSM provider utilizes triangulation techniques to try to pinpoint the location of the device, and GSM base station is further affected by factors similar to GPS in the sense of the barriers affecting signal quality and the density of GSM towers to assist in the triangulation effort, with some regional areas having errors of 500M-2KM. Command: Password+GSM+1 Notes: GSM must be in capital form. Examples: 123456GSM1 The device will send GSM locate on! +GPS info to all preset numbers, once the external power cut off. To disable this function, please send Password+GSM+0 to the device. 7. Low battery alarm: Note: When the tracker s voltage is lower than 30%, it will send a SMS alarm BAT: LOW! + GPS INFO to all preset numbers. 8. Anti-Jamming function To be able to use anti-jamming, user needs to connect siren to output, When someone use GSM jammer near the device, the siren will start to scream till jammer go away. Command: Password+JDR+1 Notes: JDR must be in capital form. Examples: 123456JDR1 To disable this function, please send Password+JDR+0 to the device. 9. GEO-FENCE Alarm Command: Password +I+X,Y,Z,xxxM/KM Notes: I, M,KM must be in capital form. - 12 -

X=No. Of Geofence (1~3), user can set 3 Geofences Y=0 means to turn off the function Y=1 means to turn on the functions Z=1 means to set alarm when the tracker enters the preset area Z=0 means to set alarm when the tracker breaches the district xxx is the preset distance to the tracker s original place, must be three digitals. M means meters KM means kilometers Example: 123456I1,1,1,100M The device will send the message to the authorized numbers as Geo Alarm!+GEO info when it enter the area you set. (User must set this function when tracker already fixed GPS signal) To turn off this function, please send Password+I+1,0,0 to the device. 10. Over Speed alarm Command: 123456+J+1, xxx Note: J must be English in capital. J0 means turn off the over speed alert function; J1 means turn on the speeding alert function. xxx should be<250 and must 3 numbers, e.g. 080= 080 km/h. Example: 123456J1,080-13 -

When the object moves exceeds 80 km/h, the unit will send SMS as Over speed! +GPS info to the authorized numbers. Send 123456J0,080 to tracker means turn off the speeding alert function. 11. GPS signal lost and recovery alert (Coordinate saving) Command: Password+K+1 Note: K must be in capital form. Example: 123456K1 The device will automatically send the latest available GPS information to the preset numbers when it enters into the area without GPS signal. If user goes into an area that does not have a GPS signal, such as a tunnel, cave, parking garage, etc. the device will know where user was 10 minutes before they went into such an area. The device will send Before +GPS info to the preset numbers. This is critical! If a motorcycle/car goes missing you ll be able to know the closest possible location before the GPS signal was lost. With any SMS sent during the period without GPS signal, the device will reply GPS information to preset numbers soonest as the GPS signal is covered. To turn off this function, please send Password+K+0 to the device. 12. Auto Tracking Command: Password+M+1, xxx(m) Notes: M must be in capital form. The numbers where xxx are situated displays the time interval in which the position message will be replayed. The letter M means minute, The setting must be in 3 digits and at maximum 999 in value, which means 001~999 Example: 123456M1,002 The tracker will in turn reply with one position message at 2 minutes. To turn off this function, please send 123456M0 to the device. 13. Movement Alert Command: Password+R+1, xxxm/km - 14 -

Notes: R must be in capital form. xxx is the preset distance to the tracker s original place, must be 3 digitals. M means meters, KM means kilometers Example: 123456R1, 100M When the tracker moves out of 100meters, it will send SMS alarm to the preset numbers. To turn off this function, please send 123456R0 to the device. 14. External power lost Alarm: Command: Password+N+1 Notes: N must be in capital form. Examples: 123456N1 The device will send external power lost +Geo-info to all preset numbers, once the external power cut off. To turn off this function, please send Password+N+0 to the device. 15. Listen-in (Voice wiretapping): Command: Password+P+1 Note: P must be in capital form. Example: 123456P1 The device will reply Monitor OK+ GPS INFO. Authorizes a phone number to make a silence call to the tracker, the track answers the call automatically and allows the caller to listen to what happens around the tracker. There is no voice indication that the call is in progress. To turn off this function, please send 123456P0 to the device. 16. GPS antenna cut alarm Device will send alarm to all authorized numbers and tracking website when GPS antenna is disconnected or cut. - 15 -

17. Two way voice communication Device will auto answer incoming call and two way voice conversation start. 18. Connect with Input/output ports: 1 Power (+) Analog Input 1 2 Input 1-3 Input 2-4 Analog Input 2 5 Output 1 6 Output 2 12 GND(-) 11 GND(-) 10 GND(-) 9 Analog Input 3 8 Input 4 + 7 Input 3 + - 16 -

Note: The connections of these ports are restricted to these alarms/alerts. Pin Number Color Description 1 (Power,AD1) Red DC In (power source). Input voltage: 6V~36V. It can detect external power voltage automatically. 2 (IN1-) Grey Digital input 1 (negative triggering). Defaulted as SOS 3 (IN2-) Purple Digital input 2 (negative triggering). for detecting vehicle door status 4 (AD Input 2) Blue 12 Bits Resolution Analog Inputs. Default to connect with fuel sensor. 5 (OUT1) Yellow Output 1, Default to connect with relay for remote immobilization. 6 (OUT2) Orange Output 2, it can be used to connect with horn, vehicle door control etc. 7 (IN3+) Pink Digital input 3 (positive triggering) 8 (IN4+) Green Digital Input 4(positive triggering), Default to connect with ACC detection. 9 (AD Input3) White 12 Bits Resolution Analog Inputs. It can be used to connect with temperature, fuel sensor etc. 10 (GND-) Black Ground 11 (GND-) Black Ground, Connecting to input 1 to be SOS button. 12 (GND-) Black Ground, connecting to vehicle power for external power supply. - 17 -

18.1 Power Connection Device is able to detect the external power voltage automatically if you connect power cable to power supply, the voltage can be read from SMS and tracking website. 18.2 Output Control 18.2.1 Cut off engine/oil. (Output 1,Pin5) Command: Password +D Notes: D must be in capital form, send it to EV604 Phone number to cut off the engine/oil to immobilize the car. There is another yellow wire but it s unnecessary for us. We just need connect the thin yellow wire with the wire which is from RELAY port on the device. Example: 123456D The device will reply "Relay Cut! +GPS INFO" to confirm the command has been successfully processed. - 18 -

Cancel the engine/oil control. Command: Password +E Note: E must be in capital form, send it to EV604 to cancel the engine/oil control. Example: 123456E The device will reply "Cut Canceled! +GPS INFO" to confirm the command has been successfully processed. 18.2.2 Output 2 control Orange wire: This is an output +12V. We don t fix this output, It can be used to connect with horn, vehicle door etc. Command: Password+X+1 Note: X must be in capital form, send it to EV604 Phone number to control the Door or Siren etc. Example: 123456X1 The device will reply "On! +GPS INFO" to confirm the command has been successfully processed. Turn off the output control: Command: Password+X+0 Note: X must be in capital form, send it to EV604 Phone number to control the Door or Siren etc. Example: 123456X0 The device will reply "Off! +GPS INFO" to confirm the command has been successfully processed. 18.3 Input control 18.3.1 SOS emergency Alarm Connect Gray (Pin2 Input 1 - ) & Black (Pin11 GND-) wires to SOS button: Once the SOS button is pressed for more than 3 seconds, an SOS Alarm will be sent to the preauthorized phone number and website. SOS button can be also used for restart the device, push SOS button for 30 seconds without stopping in the middle, device will restart by itself. - 19 -

18.3.2 Detecting vehicle door opened/closed When the door is opened, there will be negative triggering to Input 2 -, and then a detection alarm Door opened! will be sent to the server via GPRS The alert will be sent to WEB only. 18.3.3 Input 3 (positive) connects with car alarm siren. (Example) Pink wire: this is an input 3+. We don t fix this input, It can be used to connects with car alarm siren, Once the siren was triggered and screamed for more than 4 seconds, the device will send message Siren Alarm! to the preauthorized phone number and Website. - 20 -

18.3.4 ACC Detection Connect green wire (Pin8 input 4 +) with car ACC(Ignition). Once the ACC is on, a detection alarm ACC On! will be sent to the server via GPRS. This alert will be sent to WEB only. 18.4 Analog inputs (PIN4) Fuel Detection (percentage of fuel) - 21 -

Note: Fuel level sensors supplied by our company are resistance type sensors with output resistance: 0 200Ω (ohm). For the circuit shown on above figure, if VCC is 12V, R should be 200Ω (ohm) and if VCC is 24V then R should be 600Ω (ohm) to make the input range to AD1 or AD2 is 0 6V. Below formula is for calculating the fuel percentage left for this fuel level sensor: Fuel detection can also be realized without connect fuel level sensor, it can be detect by connecting fuel meter: 19 Real time tracking on website: www.smart-tracking.com 19.1 GPRS Settings: In order to use the GPRS function, the user needs to setup the APN by sending SMS command. --What is APN? Access point name (APN) is the name used to identify a general packet radio service (GPRS) bearer service in the GSM mobile network. The APN defines the type of service that is provided in the packet data connection. - 22 -

Make sure that the SIM card in the tracker supports the GPRS function. The APN can be acquired from your local GSM operators. Command: 123456S1, APN, user name, password Notes: All letters in this formula are case sensitive. Some access point name without user name and password, so please just leave it blank. Example: 123456S1, CMNET CMNET is the APN for China Mobile; therefore the user must set their particular APN for their own country which the unit resides. After sending the command, the device will reply GPRS On!+GPS INFO! 19.2 Check SIM card s APN & VPN or IP Command: Password+G+1 Note: G must be in Capital form. Example: 123456G1 The device will reply GPRS info: APN:cmnet; Name:xxx; Password:xxxx; Port:5050; VPN or IP:www.smart-tracking.com 20 Disable GPRS tracking: Command: Password+S+0 Note: S must be in Capital form. Example: 123456S0 The device will reply GPRS OFF+GPS INFO!, and in the mean time the tracker will back to SMS mode. 21 Read IMEI&Version number Command: Password+V Example: 123456V - 23 -

22. Built-in Memory The device built in 8MB flash memory inside. It will store the GPS information when do not have GSM network coverage (i.e., very low population density areas, some mountainous terrain, underground areas etc). The device will transmit GPS locations to the WEB server automatically when the GSM network is recovered. 23. Initialization: Command: RESET! Note: All letters must be in capital form. This is to make all settings back to the factory default. How to add trackers to the website: 1, Send SMS command 123456A1 to the tracker. 2, Send 123456V to get the tracker's IMEI. 3, Visit web site www.smart-tracking.com and login with your account. 4, on the left side, click "Manage". Then click "Tracker Info", and click "Add new tracker" on the left top of opened window. 5, Line 1 - Name: give the tracker a name. Line 2 - Tracker Type: any one will be OK. Line 3 - Hardware Version: Please choose EV03 here. Line 4 - IMEI: enter the IMEI that you have received by SMS command 123456V. Line 5 - User ID: This is to choose an account to manage this tracker, you can use your own account. the rest information are not necessary. Click "Add". 6, Send SMS command 123456S1,APN to the tracker. Note: APN means Access Point Name, which provided by your Mobile Service provider. If this mobile service provider requires user name and password, then the SMS command should be 123456S1,APN,USERNAME,PASSWORD If no user name and password, should be 123456S1,APN 7, Now back to the website left options. Click "Real time tracking" and click the tracker's name. You will see it online soon. - 24 -

Cautions: Please comply with the instructions to extend the unit life: 1. Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circuitry. 2. Don t use & store the unit in dusty places. 3. Don t put the unit in overheated or overcooled places. 4. Clear the unit with a piece of dry cloth. Don t clean in chemicals, detergent. 5. Don t disassemble or refit the unit. 6. Using other batteries will cause unwanted situation. 7. Don t dismount the antenna randomly, or use other antennas. This may interfere the transmission, and increase the radiation as well. Hardware Specification: Content Mainframe Dimension Specs. 106mm X 22mm X 63mm Weight GSM Frequencies 200g 850/900/1800/1900Mhz GPS chip U-blox 6 GPS sensitivity Cold start: -148dBm Hot start: -157dBm GPS accuracy 5-10m Time to First Fix Cold start 26s,Warm start 26s, Hot start 1s Working Voltage Battery 6-30V DC Chargeable 3.7V 1000mAh Static Current Storage Temperature Operation Temperature Humidity 50mAh -40 C to +85 C -20 C to +80 C 5%-95% non-condensing - 25 -