LOT NUMBER: DATE PURCHASED: / / Roast Hazelnut Room Divider with 8 Storage Bins Item # 666691 ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES AS RECEIVED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 001-877-494-2536 (Service valid only in USA) Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday Or visit our website www.baysidefurnishings.com Or e-mail your request to parts@baysidefurnishings.com THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Bayside Furnishings Page 1 Factory No. 33-10944
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Bayside Furnishings CATALOG: Roast Hazelnut Room Divider with 8 Storage Bins (RHRD) DATE OF MANUFACTURE: March 2014 MADE IN CHINA MAXIMUM LOAD 100 lb. (45.3 kg) MAXIMUM LOAD 200 lb. (90.7 kg) MAXIMUM LOAD 20 lb. (9 kg) THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY. CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1. Screw Cam Bolt into the threaded insert on panel. 2. Insert Cam Lock into pre-drilled hole on panel. 3. Make sure Cam Lock pointed arrow is pointed towards the entry of Cam Bolt. 4. Connect both panels together; making sure Cam Bolt goes into pre-drilled hole on the end of panel with Cam Lock. 5. Once Cam Bolt is connected inside Cam Lock, take a Phillips screwdriver and tighten Cam Lock clockwise. You are now ready to assemble the KD unit. Bayside Furnishings Page 2 Factory No. 33-10944
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top/Bottom Panel (2) B- Side Panel (2) C- Large Divider Panel (2) D- Center Divider (1) (With Cam lock holes) E- Small Divider Panel (4) F- Storage Basket (8) G- Basket Flooring (8) (1) 2-1/4 Bolt (8+1 extra) (2) Lock Washer (8+1 extra) (3) Flat Washer (8+1 extra) (4) Cam Lock (4+1 extra) (5) Cam Bolt (4+1 extra) (6) Large Wood Dowel (12+1 extra) (7) Small Wood Dowel (8) Cam Lock Cover (9) Wood Plug (40+1 extra) (4+1 extra) (8+1 extra) (10) Plastic Cap (8+1 extra) Allen Wrench (2) Tipping Restraint Hardware Kit (2) (Inside Plastic Bag) Tools required: Allen Wrench (provided), Phillips screwdriver and Mallet (not provided). Bayside Furnishings Page 3 Factory No. 33-10944
Assembly Instructions 1. Unpack the unit and confirm that you have all hardware and parts required. 2. Lay the Side Panels (B) on a level and protected surface with the pre-drilled holes facing up. Screw 2 Cam Bolts (5) into the plastic bushings included on the center of each Side Panel. Fully tighten with a Phillips screwdriver. 3. Insert 4 Small Wood Dowels (7) half way into the pre-drilled holes on the Large Divider Panel (C) by tapping lightly with a rubber mallet, if necessary. Position 2 Small Divider Panels (E) onto the inserted Wood Dowels and press them together. Bayside Furnishings Page 4 Factory No. 33-10944
Assembly Instructions 4. Attach the Center Divider (D) and one Small Divider Panel (E) to the assembled Small Divider Panel (E) using 4 Small Wood Dowels (7). 5. Repeat the last step to install the remaining Large Divider Panel (C) and Small Divider Panel (E) to the last assembly. Make certain they are located on the other end of Center Divider (D). 6. Insert 20 Small Wood Dowels (7) into the end holes of Large Divider Panels (C) and Center Divider (D). DO NOT put dowels into the Cam Bolt holes. 7. Insert 4 Cam Locks (4) into the side holes of the Center Divider (D) making sure the arrow on the face of Cam Lock points out and towards the entry of Cam Bolt. 8. Position the Side Panels (B) onto the inserted Small Wood Dowels (7). Press them together and secure in place by connecting the Cam Locks (4) (Refer to page 2 on Cam lock system operation supplement). Once locked in place, insert the Cam Lock Covers (8) to conceal the Cam Locks. Bayside Furnishings Page 5 Factory No. 33-10944
Assembly Instructions 9. Insert the Small Wood Dowels (7) into the end holes of both Small Divider Panels (E) and insert 3 Large Wood Dowels (6) into each end of the Side Panels (B). 10. Using the Wood Dowels as a guide, attach Top and Bottom Panels (A) to both Side Panels (B) by screwing the 2-1/4 Bolts (1) with Washers (2 and 3) into the countersunk holes on Top/Bottom Panel. Tighten the bolts with the provided Allen Wrench. Cover the countersunk holes by inserting the Wood Plugs (9) or Plastic Caps (10) provided. Gently tap the Wood Plugs or Plastic Caps with a rubber mallet to ensure they are fully seated. 11. Ask for assistance to stand the unit upright and position at the desired location in your room. 12. Unfold the Storage Baskets (F) and then place the Basket Flooring (G) inside the open basket to ensure it remains square. Position the Storage Baskets onto the compartments, as shown. 13. You can combine 2 or more units to create an attractive storage wall for your home. Bayside Furnishings Page 6 Factory No. 33-10944
TIPPING RESTRAINT HARDWARE NOTE: We have included two sets of Tipping Restraint Hardware for this unit. You must install this hardware to prevent accidents or injuries from falling unit. When properly installed, this restraint can provide protection against the unexpected tipping of the unit due to small tremors, bumps or climbing. We strongly recommend mounting this hardware to a wall stud and your unit. Please carefully read the instructions printed on the plastic bag containing tipping restraint hardware to attach the tipping restraints to the unit and the wall. NOTE: Young children can be seriously injured by tipping furniture. You must install the Tipping Restraint Hardware with the unit to prevent the unit from tipping, causing any accidents or damage. The tipping restraint is intended only as a deterrent, they are not a substitute for proper adult supervision. The tipping restraint is not an earthquake restraint. If you wish to add the extra security of earthquake restraints, they must be purchased and installed separately. Tools required: Phillips screwdriver, Mallet, Power Drill, and 3/8 Drill Bit. Bayside Furnishings Page 7 Factory No. 33-10944
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture s finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing. Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish. Stains or marks from crayons or ink markers will be difficult to remove. In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture. Further advice about wood furniture care It is best to keep your furniture in a climate controlled environment. Extreme temperature and humidity changes can cause warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as may damage the finish. Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages. We hope you enjoy your purchase for many years. Thank you for choosing Bayside Furnishings! QUALITY GUARANTEE We are confident that you will be delighted with your Bayside Furnishings purchase. Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Bayside Furnishings product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture. This warranty gives you specific legal rights and you may also have other rights which vary from State to State. Customer Service: 001-877-494-2536 (Service valid only in USA) 8:30 a.m. - 4:30 p.m., PST, Monday to Friday www.baysidefurnishings.com Retailer: Costco Wholesale U.K. Ltd, UK Home Office, Hartspring Lane, Watford, Herts WD25 8JS United Kingdom 01923 213113 Model: RHRD Bayside Furnishings Page 8 Factory No. 33-10944
IF YOU NEED TO ORDER REPLACEMENT PARTS, PLEASE USE THE LIST BELOW Roast Hazelnut Room Divider with 8 Storage Bins (RHRD) *RHRD-1-SP Side Panel *RHRD-11-WP Wood Plug *RHRD-2-TBP Top/Bottom Panel *RHRD-12-CL Cam Lock *RHRD-3-LDP Large Divider Panel *RHRD-13-CB Cam Bolt *RHRD-4-CD Center Divider *RHRD-14-CLC Cam Lock Cover *RHRD-5-SDP Small Divider Panel *RHRD-15-LWD Large Wood Dowel *RHRD-6-SB Storage Basket *RHRD-16-SWD Small Wood Dowel *RHRD-7-BF Basket Flooring *RHRD-18-AW Allen Wrench *RHRD-8-2 1/4B 2-1/4" Bolt *RHRD-19-TRHK Tipping Restraint Hardware Kit *RHRD-9-LW Lock Washer *RHRD-20-PC Plastic Cap *RHRD-10-FW Flat Washer *RHRD-CH Complete Hardware