High Precision 0 V IC Reference FEATURES Laser trimmed to high accuracy 0.000 V ±5 mv (L and U models) Trimmed temperature coefficient 5 ppm/ C maximum, 0 C to 70 C (L model) 0 ppm/ C maximum, 55 C to +5 C (U model) Excellent long-term stability 5 ppm/000 hrs (noncumulative) 0 V reference capability Low quiescent current:.0 ma maximum 0 ma current output capability 3-pin TO-5 package MIL-STD-883 compliant versions available GENERAL DESCRIPTION The is a 3-pin, temperature compensated, monolithic, band gap voltage reference that provides a precise 0.00 V output from an unregulated input level ranging from V to 30 V. Laser wafer trimming (LWT) is used to trim both the initial error at +5 C as well as the temperature coefficient, resulting in high precision performance previously available only in expensive hybrids or oven regulated modules. The 5 mv initial error tolerance and 5 ppm/ C guaranteed temperature coefficient of the L is available in a monolithic voltage reference. The band gap circuit design used in the offers several advantages over classical Zener breakdown diode techniques. Most important, no external components are required to achieve full accuracy and significant stability to low power systems. In addition, total supply current to the device, including the output buffer amplifier (which can supply up to 0 ma) is typically 750 μa. The long-term stability of the band gap design is equivalent to selected Zener reference diodes. The is recommended for use as a reference for 8-, 0- or -bit digital-to-analog converters (DACs) that require an external precision reference. The device is also ideal for all types of analog-to-digital converters (ADCs) up to 4-bit accuracy, either successive approximation or integrating designs, and can generally offer better performance than that provided by standard self-contained references. FUNCTIONAL BLOCK DIAGRAM TO-5 BOTTOM VIEW Figure. The J, K, and L are specified for operation from 0 C to 70 C; the S, T, and U are specified for the 55 C to +5 C range. All grades are packaged in a hermetically sealed 3-pin TO-5 metal can. PRODUCT HIGHLIGHTS. Laser trimming of both initial accuracy and temperature coefficient results in very low errors over temperature without the use of external components. The L has a maximum deviation from 0.000 V of ±7.5 mv from 0 C to 70 C, whereas the U guarantees ±5 mv maximum total error without external trims from 55 C to +5 C.. Because the laser trimming is done on the wafer prior to separation into individual chips, the is extremely valuable to hybrid designers for its ease of use, lack of required external trims, and inherent high performance. 3. The can also be operated in a -pin Zener mode to provide a precision 0 V reference with just one external resistor to the unregulated supply. The performance in this mode is nearly equal to that of the standard 3-pin configuration. 4. Advanced circuit design using the band gap concept allows the to give full performance with an unregulated input voltage down to 3 V. With an external resistor, the device operates with a supply as low as.4 V. 5. The is available in versions compliant with MILSTD-883. Refer to the military datasheet for detailed specifications. 0804-00 Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 906, Norwood, MA 006-906, U.S.A. Tel: 78.39.4700 www.analog.com Fax: 78.46.33 009 Analog Devices, Inc. All rights reserved.
* Product Page Quick Links Last Content Update: /0/06 Comparable Parts View a parametric search of comparable parts Documentation Application Notes AN-73: The Effect of Long-Term Drift on Voltage References Data Sheet : High Precision 0V IC Reference Data Sheet : Military Data Sheet Tools and Simulations SPICE Macro-Model Design Resources Material Declaration PCN-PDN Information Quality And Reliability Symbols and Footprints Discussions View all EngineerZone Discussions Sample and Buy Visit the product page to see pricing options Technical Support Submit a technical question or find your regional support number * This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet. Note: Dynamic changes to the content on this page does not constitute a change to the revision number of the product data sheet. This content may be frequently modified.
TABLE OF CONTENTS Features... Functional Block Diagram... General Description... Product Highlights... Revision History... Specifications... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Applying the... 6 Voltage Variation vs. Temperature... 6 Output Current Characteristics...7 Dynamic Performance...7 Precision High Current Supply...8 Connection for Reduced Primary Supply...8 The as a Current Limiter...9 Negative 0 V Reference...9 0 V Reference with Multiplying CMOS DACs or ADCs...9 Precision -Bit DAC Reference...9 Outline Dimensions... Ordering Guide... REVISION HISTORY 4/09 Rev. B to Rev. C Updated Format... Universal Changes to Table... 3 Changes to Figure... 6 Changes to Figure... 8 Changes to 0 V Reference with Multiplying CMOS DACs or ADCs Section... 9 Changes to Precision -Bit DAC Reference Section... 9 Changes to Figure 3... 9 Changes to Figure 5 and Figure 6... 0 Updated Outline Dimensions... Changes to Ordering Guide... Rev. C Page of
SPECIFICATIONS @ VIN = +5 V and TA = +5 C. Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All minimum and maximum specifications are guaranteed, although only those shown in boldface are tested on all production units. Table. J K L Model Min Typ Max Min Typ Max Min Typ Max Units OUTPUT VOLTAGE TOLERANCE (Error from Nominal 0,000 V Output) ±30 ±0 ±5 mv OUTPUT VOLTAGE CHANGE Maximum Deviation from +5 C ±3.5 ±6.75 ±.5 mv Value, TMIN to TMAX Temperature Coefficient 30 5 5 ppm/ C LINE REGULATION 5 V VIN 30 V 3.0 3.0 3.0 mv (0.00) (0.00) (0.00) %/V 3 V VIN 5 V.0.0.0 mv (0.005) (0.005) (0.005) %/V LOAD REGULATION 0 IOUT 5 ma 00 500 00 500 00 500 μv/ma QUIESCENT CURRENT 0.75.0 0.75.0 0.75.0 ma TURN-ON SETTLING TIME TO 0.% 00 00 00 μs NOISE (0. Hz TO 0 Hz) 40 40 40 μv (p-p) LONG-TERM STABILITY 5 5 5 ppm/000 hr SHORT-CIRCUIT CURRENT 30 30 30 ma OUTPUT CURRENT Source @ +5 C 0 0 0 ma Source TMIN to TMAX 5 5 5 ma Sink TMIN to TMAX 5 5 5 μa TEMPERATURE RANGE Specified 0 70 0 70 0 70 C Operating 65 +50 65 +50 65 +50 C PACKAGE OPTION TO-5 (H-03B) JH KH LH See Figure 7. H indicates the hermetic metal can. Rev. C Page 3 of
Table. Model S T U Min Typ Max Min Typ Max Min Typ Max OUTPUT VOLTAGE TOLERANCE (Error from Nominal 0,000 V Output) ±30 ±0 ±5 mv OUTPUT VOLTAGE CHANGE Maximum Deviation from +5 C ±30 ±5 ±0 mv Value, TMIN to TMAX Temperature Coefficient 30 5 0 ppm/ C LINE REGULATION 5 V VIN 30 V 3.0 3.0 3.0 mv (0.00) (0.00) (0.00) %/V 3 V VIN 5 V.0.0.0 mv Units (0.005) (0.005) (0.005) %/V LOAD REGULATION 0 IOUT 5 ma 00 500 00 500 00 500 μv/ma QUIESCENT CURRENT 0.75.0 0.75.0 0.75.0 ma TURN-ON SETTLING TIME TO 0.% 00 00 00 μs NOISE (0. Hz TO 0 Hz) 40 40 40 μv (p-p) LONG-TERM STABILITY 5 5 5 ppm/000 hr SHORT-CIRCUIT CURRENT 30 30 30 ma OUTPUT CURRENT Source @ +5 C 0 0 0 ma Source TMIN to TMAX 5 5 5 ma Sink TMIN to TMAX 00 00 00 μa Sink 55 C to +85 C 5 5 5 ma TEMPERATURE RANGE Specified 55 +5 55 +5 55 +5 C Operating 65 +50 65 +50 65 +50 C PACKAGE OPTION TO-5 (H-03B) SH TH UH See Figure 7. H indicates hermetic metal can. Rev. C Page 4 of
ABSOLUTE MAXIMUM RATINGS Table 3. Parameter Input Voltage Power Dissipation @ +5 C Operating Junction Temperature Range Lead Temperature (Soldering 0 sec) Thermal Resistance Junction-to-Ambient Rating 40 V 600 mw 55 C to +50 C +300 C 50 C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. C Page 5 of
APPLYING THE The is easy to use in virtually all precision reference applications. The three pins are simply: primary supply, ground, and output, with the case grounded. No external components are required even for high precision applications; the degree of desired absolute accuracy is achieved simply by selecting the required device grade. The requires less than ma quiescent current from an operating supply range of 3 V to 30 V. Q0 R40 C5 C5 Q6 R4 Q0 Q Q Q4 Q8 Q5 Q7 R4 R34 V+ 0V 3V TO 30V Q6 Q3 Q5 R37 C50 R33 R3 R35 0V Q3 Q4 Q Q Figure. Pin Configuration (Bottom View) An external fine trim may be desired to set the output level to exactly 0.000 V within less than a millivolt (calibrated to a main system reference). System calibration may also require a reference slightly different from 0.00 V. In either case, the optional trim circuit shown in Figure 3 can offset the output by up to ±30 mv (with the Ω resistor), if needed, with minimal effect on other device characteristics. R TRIM RANGE MAX Δ TCR Ω ±30mV 3.5ppm/ C Ω ±0mV.0ppm/ C 3.9Ω ±5mV 0.6ppm/ C 6.8kΩ 0kΩ +5V 0804-00 R +0V R39 R30 Figure 4. Simplified Schematic R3 VOLTAGE VARIATION vs. TEMPERATURE Some confusion exists in the area of defining and specifying reference voltage error over temperature. Historically, references have been characterized using a maximum deviation per degree Celsius; that is, 0 ppm/ C. However, because of nonlinearities in temperature characteristics, which originated in standard Zener references (such as S-type characteristics) manufacturers opt for the maximum limit error band approach to specify devices. This technique involves measurement of the output at three, five, or more different temperatures to guarantee that the output voltage falls within the given error band. The temperature characteristic of the consistently follows the S-curve shown in Figure 5. Three-point measurement of each device guarantees the error band over the specified temperature range. 0.005 R36 V 0804-004 5V 4.3kΩ Figure 3. Optional Fine Trim Configuration 0804-003 (V) 0.000 9.995 55 50 40 30 0 0 0 0 0 30 40 50 60 70 80 90 00 0 0 5 TEMPERATURE ( C) Figure 5. Typical Temperature Characteristic 0804-005 Rev. C Page 6 of
The error band which is guaranteed with the is the maximum deviation from the initial value at +5 C; this error band is of more use to a designer than one which simply guarantees the maximum total change over the entire range (that is, in the latter definition, all of the changes could occur in the positive direction). Thus, with a given grade of the, the designer can easily determine the maximum total error from initial tolerance plus temperature variation (for example, for the T, the initial tolerance is ±0 mv, the temperature error band is ±5 mv, thus the unit is guaranteed to be 0.000 V ±5 mv from 55 C to +5 C). OUTPUT CURRENT CHARACTERISTICS INPUT OUTPUT V V 0V 0V 0V 0V 0 50 00 50 00 50 SETTLING TIME (µs) Figure 7. Output Settling Characteristic 0.03V 0.0V 0.0V 0.00V 0804-007 OUTPUT The has the capability to either source or sink current and provide good load regulation in either direction, although it has better characteristics in the source mode (positive current into the load). The circuit is protected for shorts to either positive supply or ground. The output voltage vs. output current characteristics of the device are shown in Figure 6. Source current is displayed as negative current in the figure; sink current is positive. Note that the short-circuit current (that is, 0 V output) is about 8 ma; when shorted to +5 V, the sink current goes to about 0 ma. 000 00 0 NOISE SPECTRAL DENSITY (nv/ Hz) TOTAL NOISE (µv rms) UP TO SPECIFIED FREQUENCY OUTPUT VOLTAGE (V) 4 0 8 6 4 0 = 5V T A = 5 C 0 5 0 5 0 5 0 5 0 SOURCE SINK OUTPUT CURRENT (ma) Figure 6. Output Voltage vs. Sink and Source Current DYNAMIC PERFORMANCE Many low power instrument manufacturers have been increasingly concerned with the turn-on characteristics of the components used in their systems. Fast turn-on components often enable the end user to keep power off when not needed, and yet respond quickly when the power is turned on for operation. Figure 7 displays the turn-on characteristic of the. This characteristic is generated from a cold start operation and represents the true turn-on waveform after an extended period with the supplies off. The figure shows both the coarse and fine transient characteristics of the device; the total settling time to within ±0 mv is about 80 μs, and there is no long thermal tail appearing after the point. 0804-006 0 00 k 0k 00k M FREQUENCY (Hz) Figure 8. Spectral Noise Density and Total rms Noise vs. Frequency 000 900 SUPPLY CURRENT (µa).5µa/ C 800 700 600 500 55 50 40 30 0 0 0 0 0 30 40 50 60 70 80 90 00 0 0 5 TEMPERATURE ( C) Figure 9. Quiescent Current vs. Temperature 0804-008 0804-009 Rev. C Page 7 of
PRECISION HIGH CURRENT SUPPLY The can be easily connected with power pnp or power Darlington pnp devices to provide much greater output current capability. The circuit shown in Figure 0 delivers a precision 0 V output with up to 4 A supplied to the load. The 0. μf capacitor is required only if the load has a significant capacitive component. If the load is purely resistive, improved high frequency supply rejection results from removing the capacitor. V IN 5V 470Ω CONNECTION FOR REDUCED PRIMARY SUPPLY Whereas line regulation is specified down to 3 V, the typical works as specified V. The current sink capability allows even lower supply voltage capability such as operation from V ±5% as shown in Figure. The 560 Ω resistor reduces the current supplied by the to a manageable level at a full 5 ma load. Note that the other band gap references, without current sink capability, may be damaged by use in this circuit configuration. V ±5% 560Ω 5% 0.µF N6040 0V @ 0mA TO 5mA Figure. V Supply Connection 0804-0 0V @ 4A Figure 0. High Current Precision Supply 0804-00 Rev. C Page 8 of
THE AS A CURRENT LIMITER The represents an alternative to current limiter diodes that require factory selection to achieve a desired current. This approach often results in temperature coefficients of %/ C. The approach is not limited to a defined set current limit; it can be programmed from 0.75 ma to 5 ma with the insertion of a single external resistor. Of course, the minimum voltage required to drive the connection is 3 V. The AD580, which is a.5 V reference, can be used in this type of circuit with compliance voltage down to 4.5 V. 0.µF 5V.kΩ 5% Figure 3. -Pin 0 V Reference ANALOG V REF 0V 0804-03 0V = R LOAD i ~ 0V = + 0.75mA R BOTTOM VIEW OF 0V PRECISION REFERENCE CIRCUIT IN TO-5 CASE Figure. A Two-Component Precision Current Limiter NEGATIVE 0 V REFERENCE The can also be used in a -pin Zener mode to provide a precision 0.00 V reference. As shown in Figure 3, the +VS and VOUT pins are connected together to the high supply (in this case, ground). The ground pin is connected through a resistor to the negative supply. Thus, the output is taken from the ground pin instead of VOUT. With ma flowing through the in this mode, a typical unit shows a mv increase in output level over that produced in the 3-pin mode. Note also that the effective output impedance in this connection increases from 0. Ω typical to Ω. It is essential to arrange the output load and the supply resistor, RS, so that the net current through the is always between ma and 5 ma. For operation to +5 C, the net current should be between ma and 5 ma. The temperature characteristics and long-term stability of the device are essentially the same as that of a unit used in the standard 3-pin mode. The can also be used in a -pin mode to develop a positive reference. +VS and VOUT are tied together and to the positive supply through an appropriate supply resistor. The performance characteristics are similar to those of the negative -pin connection. The only advantage of this connection over the standard 3-pin connection is that a lower primary supply can be used, as low as 0.5 V. This type of operation requires considerable attention to load and primary supply regulation to maintain the within its regulating range of ma to 5 ma ( ma to 5 ma for operation beyond +85 C). 0804-0 0 V REFERENCE WITH MULTIPLYING CMOS DACs OR ADCs The is ideal for application with the entire AD7533 series of 0- and -bit multiplying CMOS DACs, especially for low power applications. It is equally suitable for the AD7574 8-bit ADC. In the standard hook-up, as shown in Figure 5, the +0 V reference is inverted by the amplifier/dac configuration to produce a 0 V to 0 V range. If an OP77 amplifier is used, total quiescent supply current is typically ma. If a 0 V to +0 V full-scale range is desired, the can be connected to the CMOS DAC in its 0 V Zener mode, as shown in Figure 3 (the 0 VREF output is connected directly to the VREF IN of the CMOS DAC). The is normally used in the 0 V mode with the AD7574 to give a 0 V to +0 V ADC range. This is shown in Figure 5. Bipolar output applications and other operating details can be found in the data sheets for the CMOS products. DIGITAL INPUT BIT 0 (LSB) +0V +5V V REF IN BIT (MSB) 5 4 R FEEDBACK 4 6 5 I OUT 3 3 I OUT +5V 5V Figure 4. Low Power 0-Bit CMOS DAC Application 0V TO 0V PRECISION -BIT DAC REFERENCE AD565A, like most DACs, is designed to operate with a +0 V reference element. In the AD565A, this 0 V reference voltage is converted into a reference current of approximately 0.5 ma via the internal 9.95 kω resistor (in series with the external 00 Ω trimmer). The gain temperature coefficient of the AD565A is primarily governed by the temperature tracking of the 9.95 kω resistor and the 5 kω to0 kω span resistors; gain TC is guaranteed to 3 ppm/ C. Thus, using the L (at 5 ppm/ C) as the 0804-04 Rev. C Page 9 of
0 V reference guarantees a maximum full-scale temperature coefficient of 8 ppm/ C over the commercial range. The 0 V reference also supplies the normal ma bipolar offset current through the 9.95 kω bipolar offset resistor. Consequently, the bipolar offset TC depends only on TC matching of the bipolar offset resistor to the input reference resistor and is guaranteed to 3 ppm/ C. 0.µF 5V R3.kΩ 5% GAIN TRIM R kω ANALOG SUPPLY RETURN +5V 0V REF R kω 0% SIGNAL INPUT 0V TO +0V AD7574 8 (TOP VIEW) 3 4 5 GROUND INTERTIE ANALOG GROUND R AND R CAN BE OMITTED IF GAIN TRIM IS NOT REQUIRED. Figure 5. as 0 V Reference for CMOS ADC DIGITAL SUPPLY RETURN 0804-05 5V +5V/+5V +5V 0.µF CONTROL AMP SUMMING JUNCTION GAIN ADJ. 0V 00Ω, 5T R A 0.µF 4 5 3 6 9.95kΩ 0.5mA CONTROL AMP A BIT (MSB) 4 BIT 3 BIT 3 BIT 4 BIT 5 0 BIT 6 9 BIT 7 PNP LOGIC SWITCHES AND LEVEL SHIFTERS 5V 8 BIT 8 7 BIT 9 6 BIT 0 5 BIT 4 3 BIT (LSB) 5kΩ (8kΩ) 5kΩ (8kΩ) OP77 AD565A R3 +5V 8 3.0MΩ 9.950kΩ (5.95k) 0 9 7 3 5V R4 0kΩ, 5T UNIPOLAR OFFSET ADJ. OP AMP OUTPUT R 00Ω, 5T BIPOLAR OFFSET ADJ. Figure 6. Precision -Bit DAC A = ANALOG GROUND 0804-06 Rev. C Page 0 of
OUTLINE DIMENSIONS 0.85 (4.70) 0.65 (4.9) 0.500 (.70) MIN 0.00 (.54) TYP 0.370 (9.40) 0.335 (8.5) 0.335 (8.5) 0.305 (7.75) 0.030 (0.76) MAX 0.09 (0.48) 0.06 (0.4) 0.00 (5.08) TYP 3 45 0.045 (.4) 0.09 (0.74) 0.034 (0.86) 0.08 (0.7) BASE & SEATING PLANE CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 030309-A Figure 7. 3-Pin Metal Header Package [TO-5] (H-03B) Dimensions shown in inches and (millimeters) ORDERING GUIDE Model Temperature Range Package Description Package Option JH 0 C to +70 C 3-Pin Metal Header Package (TO-5) H-03B KH 0 C to +70 C 3-Pin Metal Header Package (TO-5) H-03B LH 0 C to +70 C 3-Pin Metal Header Package (TO-5) H-03B SH 55 C to +5 C 3-Pin Metal Header Package (TO-5) H-03B TH 55 C to +5 C 3-Pin Metal Header Package (TO-5) H-03B UH 55 C to +5 C 3-Pin Metal Header Package (TO-5) H-03B RoHS compliant model as of Date Code 073. Rev. C Page of
NOTES 009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D0804-0-4/09(C) Rev. C Page of