CDPS-U4H4HSA 4 by 4 HDMI with Audio Matrix Fast Switch Operation Manual
DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document. Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual, or otherwise without express written permission and consent from Cypress Technology. Copyright 2014 by Cypress Technology. All Rights Reserved. Version 1.0 May 2014 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. Never spill liquid of any kind on or into this product. Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. REVISION HISTORY VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE RDV1 21/05/14 Preliminary Release
CONTENTS 1. Introduction... 1 2. Applications... 1 3. Package Contents... 1 4. System Requirements... 1 5. Features... 2 6. Operation Controls and Functions... 3 6.1 Front Panel...3 6.2 Rear Panel...5 6.3 OSD Menu...5 6.4 Remote Control...11 6.5 RS-232 Protocols...13 6.6 RS-232 Commands...14 6.7 Web GUI Control...17 7. Connection Diagram... 19 8. Specifications... 20 9. Acronyms... 22
1. INTRODUCTION The 4 by 4 HDMI matrix with audio which allows HDMI signal from any of its four sources to be routed to and displayed on any of its four connected HDMI displays simultaneously plus an additional audio selection and extension allows users to utilise both vidoeo and audio more efficiency. With fast switching technology the device can greatly eliminate the time required by swapping or turning ON/OFF the connected displays. It supports 4Kx2K, 3D, 36-bit Deep Color, Hi- Def lossless audio and other features defined by HDMI specifications. The management of source/sink scenarios can be operated easily through on-panel buttons, IR remote control, RS-232 or Ethernet protocol. 2. APPLICATIONS Home Theater/Entertainment Lecture Room/Hall Presentation Show Room/Demo Room Public Commercial Display Information Board 3. PACKAGE CONTENTS 4 by 4 HDMI 4Kx2K Matrix with Audio Remote Control with Battery Left & Right Rack Ears 12V/3A DC Power Adaptor IR Receiver Cable Operation Manual 4. SYSTEM REQUIREMENTS Input source equipments such as Blu-ray/DVD/PS3 player or Set- Top-Box and output HDMI TV/Display and or audio amplifier with connection cables. 1
5. FEATURES HDMI with 3D & 4Kx2K supported, HDCP and DVI compliant Supports four HDMI inputs and four HDMI outputs Supports external audio inputs and outputs for HDMI outputs selection and additional audio extension up to 300M Displays any of four High-Definition sources on four HDTV displays simultaneously with fast switch 3DTV Pass-Through Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30 & 50/60 Y420 4096x2160@24 & 50/60Hz Y420) Supports data rate from 300Mbps to 3Gbps and Deep Color up to 1080p 36-bit Supports individual EDID or common EDID Supports LPCM 2/5.1/7.1CH, Dolby Digital 2~5.1CH, DTS 2~5.1CH (Pass through), Dolby TrueHD and DTS-HD Master Audio Input port HDCP support Standard and Apple mode. The Apple mode selection to guarantees the use of Apple devices 2
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel 4 6 8 1012 14151718 3 POWER 4X4 HDMI WITH AUDIO MATRIX FAST SWITCH OUT A OUT B OUT C OUT D VIDEO DIGITAL IN 1 IN 2 IN 3 IN 4 AUDIO HDMI MUTE DOWNMIX 1 2 3 5 7 9 11 131516 19 CANCEL TAKE MENU ENTER + - ALL PRESET LOCK 4K UHD + AUDIO 1 POWER: Press this button to turn ON the device and the LED will illuminated. 2 IR Window: This IR Receiver receives the remote control signal from the package include remote control only. 3 IN 1~4: Press these IN buttons to select an input from the 4 input sources. 4 OUT A/D: Press these buttons once a time along with an IN buttons to select an input source for an output display. i.e. OUT A IN1 TAKE or OUT B IN4 TAKE. 5 AUDIO: Press this button to display audio only for outputs. 6 VIDEO: Press this button to perform video only for output displays. 7 HDMI: Press this button to display video only for outputs. 8 DIGITAL: Press this button to select an input source audio. 9 DOWNMIX: Press this button to downmix the audio. 10 MUTE: Press this button to mute all the audio output sound. To unmute, press it again. 11 TAKE: Press this button to confirm the selection of an IN and an OUT button. 12 CANCEL: Press this button to cancel the IN/OUT selection. 13 ENTER: Press to confirm the selection. 14 MENU: Press to enter into the menu. 15 +/-: Press these buttons to move up/down under menu selection. 16 PRESET: Press PRESET, the OLED menu will show Preset then select IN 1~4. Preset 1~4 after the selection, press TAKE to confirm the selection or press CANCEL to cancel the selection.
17 All: Press this button to select all outputs to display with an input source. 18 LOCK: Press this button to lock all button functions on the panel. Press 3 seconds to relieve the lock function. 19 LCM: Displaying Input and Outputs selection and menu selection. 6.2 Rear Panel HDMI IN 1 2 3 4 HDMI OUT A B C D S/PDIF IN 1 2 A S/PDIF OUT B AUDIO-CAT 3C 4D SERVICE CONTROL RS232 IR IN DC 12V 1 2 3 4 5 6 7 8 9 10 1 HDMI IN: Connect from source equipments such as Blu-ray/DVD/ PS3 players, Set-Top-Box or any HDMI equipped source device for input signal sending. 2 HDMI OUT: Connect to HDMI TV/display or HD Amplifier for output image and or audio display. 3 S/PDIF IN: Connect from source equipment such as DVD, Blu-ray, PS3 or etc. with audio singal. 4 S/PIDF OUT: Connect to active speaker or audio amplifier for audio distribution. 5 AUDIO-CAT: Connect this port to the AUDIO-CAT input of the Receiver unit using CAT5e/6/7 cable. 6 SERVICE: This slot is reserved for firmware update use only. 7 CONTROL: Connect from PC/Laptop with active internet service for Web GUI control with RJ-45 terminated cable. 8 RS232: Connect from PC/Laptop for RS-232 command sending to control the device. 9 IR IN: Connect the IR Receiver included in the package for IR signal receive from the included remote control. 10 DC 12V: Connect the adaptor with power cord included in the package and connect to AC wall outlet for power supply. 4
6.3 OSD Menu Main Menu Sub Menu Description Default EDID Mode All All Input port is using same EDID. In menu EDID All, can select suitable EDID. Appoint Exit Each Input port can select individual EDID. In menu EDID IN1~4 select suitable EDID. All 5
EDID All Sink A Copy Output A display EDID Sink B Sink C Sink D 8/2D/ PCM/720p 8/2D/PCM/ AC3/720p 8/2D/ PCM/1080p 8/2D/PCM/ AC3/1080p Copy Output B display EDID Copy Output C display EDID Copy Output D display EDID Standard EDID, Content: deep color/2d3d/audio/ native resolution Standard EDID, Content: deep color/2d3d/audio/ native resolution Standard EDID, Content: deep color/2d3d/audio/ native resolution Standard EDID, Content: deep color/2d3d/audio/ native resolution 8/2D/ PCM/4K2K 8/2D/PCM/ AC3/4K2K Exit Standard EDID, Content: deep color/2d3d/audio/ native resolution Standard EDID, Content: deep color/2d3d/audio/ native resolution 8/2D/ PCM/1080p 6
EDID IN1 Same EDID All Select Input 1 s EDID EDID IN2 Same EDID All Select Input 2 s EDID EDID IN3 Same EDID All Select Input 3 s EDID EDID IN4 Same EDID All Select Input 4 s EDID Same EDID All Same EDID All Same EDID All Same EDID All Matrix Preset Preset 1 IN/OUT default No.1 A=1, B=2, C=3, D=4 HDCP Input Preset 2 No.2 A=1, B=2, C=3, D=4 Preset 3 No.3 A=1, B=2, C=3, D=4 Preset 4 No.4 A=1, B=2, C=3, D=4 Exit IN1 Standard/ Apple IN2 Standard / Apple IN3 Standard / Apple Set IN1 in Apple/ Standard mode Set IN2 in Apple/ Standard mode Set IN3 in Apple/ Standard mode Standard Standard Standard IN4 Standard / Apple Exit Set IN4 in Apple/ Standard mode Standard 7
Network Setup IP Mode DHCP, Static Static IP Setup Static IP 192.168.5.83 Mask Gate Do Re-Link Exit Setup Static Netmask Setup Static Gateway Re-Link. After setup Network, the system need to relink Network Status Link Network status DHCP,Static or Not Linked Source Detection 255.255.255.0 192.168.5.254 --- --- IP Get IP --- Mask Get Netmask --- Gate Get Gateway --- MAC Exit IN1 On/Off, IN2 On/Off IN3 On/Off, IN4 On/Off Exit System MAC Address IN1, IN2 detect source with/without the signal & HDCP IN3, IN4 detect source with/without the signal & HDCP --- --- 8
Sink A Info Type, Manuf. Detect and Analysis Output A display s EDID Content: type(hdmi/ DVI/VGA), Manufactory/ Model number Sink B Info Sink C Info Sink D Info Native Video Format Audio Format Exit Same Sink A Info Same Sink A Info Same Sink A Info Content: native resolution Content: deep color, 2D or 3D, 4K2K Content:PCM, BitStream, HBR Detect and Analysis Output B display s EDID Detect and Analysis Output C display's EDID Detect and Analysis Output D display's EDID Firmware FW Version Display the model number and FW version Update Exit FW Update Factory Reset Do Reset Do system Reset --- Exit Exit --- --- --- --- --- 9
6.4 Remote Control 1 POWER: Press this button to switch the system ON/OFF. 2 OUT A/D: Press these buttons onc a time along with an IN buttons to select an input source for an output display. 3 MENU: Press to enter into the menu. 4 ENTER: Press to confirm the selection. 5 IN1~4: Press the IN buttons to select an input from the 4 input sources. 6 ALL: Press this button to select all outputs to display with an input source. 7 TAKE: Press this button to confirm the selection of an IN and an OUT button. ENTER - 8 CANCEL: Press this button to cancel the IN/OUT selection. 9 PRESET: Press PRESET, the OLED menu will showing Preset and select IN 1~4. After preset 1~4, press TAKE to confirm the selection or press CANCEL to cancel the selection. 10 LOCK: Press this button to lock all button functions on the panel. Press 3 seconds to relieve the lock function. 11 +/-: Press these buttons to move up/down under menu selection. 1 2 3 4 OUT A OUT B OUT C ALL IN 1 TAKE IN 2 CANCEL IN 3 OUT D PRESET IN 4 MENU LOCK + CR-138 MODE 5 6 7 8 9 10 11 10
6.5 RS-232 Protocols CDPS-U4H4HSA Remote Control PIN Assignment PIN Assignment 1 NC 1 NC 2 Tx 2 Rx 3 Rx 3 Tx 4 NC 4 NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC Baud Rate: 115200bps Data bit: 8 bits Parity: None Flow Control: None Stop Bit: 1 11
6.6 RS-232 Commands Command Name Description Description of parameter P0 POWER OFF NONE P1 POWER ON NONE IPCONFIG SIPADDR XXX.XXX. XXX.XXX SNETMASK XXX. XXX.XXX.XXX SGATEWAY XXX. XXX.XXX.XXX DISPLAY THE CURRENT IPCONFIG SET ETHERNET IP AD- DRESS SET ETHERNET NETMASK SET ETHERNET GATEWAY NONE XXX=0~255 XXX=0~255 XXX=0~255 HTTPPORT N SET ETHERNET PORT N=0~65535 NUMBER RSTIP IP CONFIGURATION NONE RESET TO <DHCP> A N SET OUTPUT A SOURCE N=1-4 B N SET OUTPUT B SOURCE N=1-4 C N SET OUTPUT C SOURCE N=1-4 D N SET OUTPUT D SOURCE N=1-4 I N SET ALL OUTPUTS SOURCE N=1-4 EDIDMODE N SHOW EDID MODE N=(1)All (0)Appoint EDIDALL EDIDALL N EDIDIN EDIDIN N1 SHOW EDID MODE SOURCE FOR ALL SET EDID CONTENT FOR ALL SHOW ALL INPUT EDID SOURCE SHOW INPUT N1 EDID SOURCE NONE N=0-9 NONE N1=1-4 12
EDIDIN N1 N2 HDCPIN HDCPIN N1 HDCPIN N1 N2 PRESET PRESET N1 PRESET N1 N2 SOURCEDET SOURCEDET N1 SINKINFO SINKINFO N1 INNAME SET INPUT N1 EDID SOURCE SHOW ALL INPUT HDCP STATUS SHOW INPUT N1 HDCP STATUS SET INPUT N1 HDCP ON/OFF SHOW ALL PRESET CONFIG SHOW PRESET N1 CONFIG SET PRESET N1 CONFIGURE SHOW ALL INPUT SIGNAL SHOW INPUT N1 SIGNAL SHOW ALL OUTPUT INFORMATION SHOW OUTPUT N1 INFORMATION N1=1-4 N2=0-9 NONE N1=1-4 N1=1-4 N2=(0)OFF (ON) NONE N1=1-4 N1=1-4 N2=AXBX (X=1-6,M) NONE N1=1-4 NONE N1=A-B SHOW ALL INPUT NAME NONE INNAME N1 SHOW INPUT N1 NAME N1=1-4 INNAME N1 N2 SET INPUT N1 NAME N1=1-4 N2=ABCDEFGH OUTNAME SHOW ALL OUTPUT NAME NONE OUTNAME N1 SHOW OUTPUT N1 NAME N1=A-B OUTNAME N1 N2 SET OUTPUT N1 NAME N1=A-B N2=ABCDEFGH 13
MATRIXMODE SHOW MATRIX CURRENT MODE NONE MATRIXMODE N1 SET MATRIX MODE N1=0-1 VER SHOW DESCRIPT OF UNIT NONE REBOOT SYSTEM REBOOT NONE HELP SHOW COMMAND LIST NONE HELP N SHOW DESCRIPT OF COMMAND N : command name Note: All the RS-232 command will be not executed unless followed with a carriage return. All commands are case-sensitive. 6.7 Web GUI Control On a PC/Laptop that is connected to an active network system, open a web browser and type device s IP address (available from LCM monitor or OSD menu) on the web address entry bar. The browser will display the device s Status, IO Status, Matrix Control, Settings and Network Configuration control pages for users to control. Click on IO Status for input and output selection. 14
Click on Matrix Control for outputs and EIDID selections. Click on Settings to set each input s HDCP Control and Preset Configuration. 15
Click on Network Configuration to set the device s IP configuration. Once the changes is saved the system will reset the IP address on the device automatically and user will need to re-enter the IP address to continue the Web GUI function. 16
OUT A OUT B OUT C IN 3 OUT D PRESET IN 4 MENU ENTER - ALL IN 1 TAKE IN 2 CANCEL LOCK + CR-138 MODE 7. CONNECTION DIAGRAM Blu-ray/DVD/ PS3 Players Blu-ray/DVD/ PS3 Players Blu-ray/DVD/ PS3 Players HDMI IN 1 2 3 4 Blu-ray/DVD/ PS3 Players HD TV/ Display HDMI OUT A B C D HD TV/ Display HD TV/ Display S/PDIF IN 1 2 HD TV/ Display A S/PDIF OUT B AUDIO-CAT 3C 4D SERVICE CONTROL PC/Laptop RS232 IR IN DC 12V 3m 60 Blu-ray's Remote 17
8. SPECIFICATIONS Frequency Bandwidth Input Ports Output ports Resolution Output Level THD+N Frequency Response SNR Crosstalk IR Frequency Power Supply ESD Protection Dimensions Weight Chassis Material Silkscreen Color Operating Temperature Storage Temperature Relative Humidity 340Mbps to 3Gbps 4 x HDMI, 2 x S/PDIF 1 x USB (Service only) 1 x Control 1 x RS-232 1 x IR 4 x HDMI, 2 x S/PDIF, 2 x AUDIO-CAT 480i~1080p@50/60, 1080p@24, 4K x 2K (3840x2160/4096x2160@24/50/60Hz Y420) VGA~WUXGA 30~50kHz 12VDC/3A (US/EU standards, CE/FCC/UL certified) Human body model: ±8kV (air-gap discharge) ±4kV (contact discharge) 438mm (W) x 269mm (D) x 44mm (H) /Jacks Excluded 482mm (W) x 278mm (D) x 50mm (H) /Jacks & Rack Ears Included 2936 g Metal Black Power Consumption (W) 4.7 0 C~40 C / 32 F ~ 104 F -20 C~60 C / -4 F ~ 140 F 20~90% RH (no condensation) 18
DVI and HDMI Supported Resolutions Input Output 640x480@60 V V 640x480@72 V V 640x480@75 V V 720x480@60 V V 720x576p@50 V V 800x600@60 V V 800x600@72 V V 800x600@75 V V 1024x768@60 V V 1024x768@70 V V 1024x768@75 V V 1280x720@50 V V 1280x720@60 V V 1280x720p@60 V V 1280x768@60 V V 1280x800@60 V V 1280x1024@60 V V 1360x768@60 V V 1600x1200@60 V V 1920x1080i@50 V V 1920x1080i@60 V V 1920x1080p@24 V V 1920x1080p@25 V V 1920x1080p@30 V V 1920x1080p@50 V V 1920x1080p@60 V V 1920x1200@60(RB) V V 3840x2160@24/25/30 V V 4096x2160@24 V V 19
Audio Sampling Rate Up to 192 khz HDMI input (Up to 192kHz) HDMI output LPCM 2CH V LPCM 5.1CH V LPCM 7.1CH Dolby Digital 2~5.1CH/ DTS 2~5.1CH Dolby TrueHD/ DTS-HD Master Audio Audio Format HDMI input LPCM 2CH LPCM 5.1CH LPCM 7.1CH LPCM 2/5.1/7.1CH,Dolby Digital 2~5.1CH, DTS 2~5.1CH (Pass through), Dolby TrueHD and DTS-HD Master Audio Dolby Digital 2~5.1CH/ DTS 2~5.1CH Dolby TrueHD/ DTS-HD Master Audio 9. ACRONYMS ACRONYM CEC DVI HDCP HDMI 4Kx2K COMPLETE TERM Consumer Electronic Control Digital Visual Interface V V V HDMI output High-bandwidth Digital Content Protection High Definition Multimedia Interface 3840x2160/ 4096x2160 V V V V V 20
CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.tw MPM-CDPSU4H4HSA