LCD Screen for Wireless/Wired CCTV Kits CA2 Installation and Operating Instructions These instructions should be retained in a safe place for future reference.
CONTENTS 1 INTRODUCTION 3 2 KIT CONTENTS 5 3 FEATURES 5 4 INSTALLATION 6 4.1 Wireless Camera(s) Setup 6 4.2 Screen Installation and Setup 6 5 OPERATION 8 5.1 Wired/Wireless Source Function 9 5.2 Wireless Camera(s) Function 9 5.2.1 Manual Function 9 5.2.2 Auto Function 9 5.2.3 Scan Function 9 5.2.4 Cam 1 to 3 Function 9 5.3 Volume Adjustment for A/V Input Source(s) 10 5.4 General Screen Settings 10 6 MAINTENANCE 11 7 TROUBLESHOOTING 11 8 ACCESSORIES IN THE RANGE 12 9 TECHNICAL SPECIFICATION 13 10 APPENDIX 14 Screen Mounting Guide 14 11 DISPOSAL RECYCLING INSTRUCTIONS 15 12 GUARANTEE AND CUSTOMER HELPLINE 16 Please read before you start: Always use discretion when installing CCTV surveillance equipment especially when there is perceived policy. Enquire regarding local regulations applicable to the lawful installation of video recording/surveillance. Third party consent may be required. 2
INTRODUCTION Section 1 The Response Colour LCD Screen allows surveillance of any vulnerable places or areas you wish to monitor. It allows you to connect both wired and wireless cameras (operating on the 2.4GHz transmission frequency). You can connect up to 2 wired cameras and up to 3 wireless cameras for surveillance. LCD Screen 2.4GHz Up to 3 Wireless Cameras 2.4GHz transmission frequency + 2 Wired Cameras 5 Cameras can be used with the LCD Screen The screen can also be used to view video and hear audio output from devices such as DVD players, camcorders, etc, using any of the the 2 wired inputs via the supplied adaptors. IMPORTANT: Other devices transmitting on the 2.4GHz frequency may be picked up by this monitor on any wireless channel. If this is experienced investigate the cause of interference. Typical examples of devices operating on this frequency around the home can include wireless routers or cordless phones. Avoid placing the LCD screen near to any potential source of RF interference, a microwave oven or a metal radiator. For best transmission, avoid installations where there are very thick walls or major obstructions between the wireless camera and LCD screen. 3
SAFETY AND INSTALLATION TIPS: The screen is intended for internal use only. The Remote Control is supplied fitted with a CR2025 Lithium coin cell battery. If it is removed, do not place in your mouth as this could impair your health. Keep these cells out of reach from young children as they are a choking hazard. The battery should not be exposed to excessive heat as this could reduce the battery s life. Damage to the unit may occur if the battery is replaced incorrectly according to the polarity of the battery terminals in the Remote. Replace only with the same or equivalent type. Do not attempt to open the unit with the power adaptor plug connected to avoid any risk of personal injury. When installing any wired/wireless CCTV camera(s), always follow the manufacturer s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. Before drilling holes through walls check for hidden electricity cables and water pipes. The use of a cable/pipe detector is advisable. When installing the camera(s), it is advisable to use cable conduit to protect any video/power extension cables from being exposed externally and to prevent/reduce the chances of the cables being tampered. After drilling any hole though an external wall for a cable, ensure the hole is sealed up around the cable using a sealant to prevent drafts. There are no user serviceable parts inside. Refer servicing to qualified service personnel. 4
KIT CONTENTS Section 2 1 x 7 Colour LCD Screen 1 x Remote Control (supplied fitted with a 3V CR2025 battery) 2 x Wired cameras adaptor leads 1 x Power supply adaptor 1 x Monitor fixing kit wall plugs and screws 1 x Installation and operating manual Tools Required: (only for wall/ceiling mounting the screen) Electric drill 6mm drill bit (use a masonry bit if mounting on concrete walls/ceilings) FEATURES Section 3 2.4GHz wireless technology to receive up to 3 wireless cameras 2 x wired inputs for viewing the output from wired cameras and other devices such as DVD players, camcorders, VCR s, etc. 7.0 inch LCD for good quality picture display Remote control Manual switching between wired and wireless cameras Selectable screen ratio of 4:3 (standard), 16:9 (DVD movie) and extended 4:3 Up/down reverse function when the screen is installed upside down Can be wall, table or ceiling mounted Dwelling function for automatically viewing each wireless camera at a time (Note: this function is not available for wired cameras) 5
INSTALLATION Section 4 4.1 Wireless Camera(s) Setup This screen is compatible with wireless cameras operating on the 2.4GHz frequency. Do not set multiple cameras on the same channel or interference will appear on the screen. It is possible to link up to 3 wireless cameras; however you may need to adjust the orientation of the screen depending on the reception of the viewing channel. If interference is experience by any of the camera and the source of inference cannot be located, then set this camera to any of the unused channels. Note: the channel 4 setting on any wireless camera must not be selected as this screen only operates with wireless cameras set to channels 1 to 3. Refer to the installation and operating manual of your wireless camera for setting the channel. 4.2 Screen Installation and Setup LCD SCREEN CAM 1 CAM 2 CAM 3 SCAN AUTO MANUAL Earphone Jack LCD Screen Power Supply Adaptor DC IN 9V Power Jack (on back of base) CAM 1 CAM 2 CAM 3 Scan Auto Manual Infra-Red Receiver for Remote Control 1. The screen can be placed on the table (flat horizontal surface), wall or upside down mounted. If wall mounting, use the mounting guide in the Appendix section of this instruction manual. Mark and drill two holes using a 6mm drill bit. Use the fixing screws and plugs provided. 6
2. To connect wired cameras or other devices such as a DVD player to this screen, use the supplied wired cameras adaptor lead. Up to two units can be connected to this monitor at the same time using the two adaptors supplied. 2.1 Plug the jack plug end(s) of the adaptor(s) into the AV IN ports. REAR OF LCD SCREEN A/V IN 1 A/V IN 1 A/V IN 2 A/V IN 2 A/V OUT A/V OUT DC IN 9V Power Jack 2.2 Connect the RCA male plug end of the wired camera into the yellow plug of the adaptor to view video only. If other devices such as a DVD player are connected then use both the yellow and white plugs for video and audio output. 3. The screen s DIP switch is located on the bottom panel. These should be adjusted to reflect the number of wireless camera channel(s) in use. By default it will be supplied set to 1 meaning only one wireless camera will link to it when powered up. 1 2 3 1 2 3 1 2 3 Camera 1 in Use Cameras 1 and 2 in Use Cameras 1, 2 and 3 in Use 4. To use any earphones with this unit, plug the earphones into the socket provided on the side. 7
Menu OPERATION Section 5 5. The output from the screen can be viewed on a larger screen using the optional A/V OUT port. Use any of the supplied two adaptors leads with this kit. You will need to source a suitable AV output adaptor with male type RCA plugs to connect to the adaptors supplied. LCD SCREEN - FRONT CAM 1 CAM 2 CAM 3 SCAN AUTO MANUAL Mirror Mute CAM 1 CAM 1 CAM 2 CAM 3 Scan Auto Manual LCD SCREEN - TOP Menu Manual Auto Mute Manual Auto Mirror CAM1 CAM2 Up/Down CAM3 Source CAM 2 CAM 3 Source Power Source Menu - Volume + Scan Scan CAM 3 Power Source Menu Volume/Adjust REMOTE CONTROL LCD Screen Control Functions 1. Turn ON any wireless cameras if setup. Turn ON any wired camera(s) or devices connected to the screen. 2. Plug the LCD screen s power supply adaptor into the power jack on the rear of the LCD base. 3. Remove the battery isolation tab located on the battery cover on the Remote Control unit. 4. Turn on the LCD screen by pressing the POWER button at the top of the monitor. By default, the monitor will automatically search for any active wireless cameras, depending on the numbers of channels setup on the screen. It will display each wireless camera at a time (4 seconds default) and repeat the cycle. The screen can be set to operate in one of three modes: Scan, Auto or Manual. The desired operating mode can be selected using the buttons on the front panel or by using the supplied Remote Control. 8
5.1 Wired/Wireless Source Function Each time the SOURCE button is pressed, the screen will change from wireless to wired. If any wired cameras or devices are connected using the wired adaptors, then press this button to view the required source. 5.2 Wireless Camera(s) Functions 5.2.1 Manual Function To view a specific wireless camera, press the MANUAL button until the required camera is viewed. The screen will switch to a different camera each time the Manual button is pressed. 5.2.2 Auto Function When the AUTO button is pressed, the screen will return to cycle or dwell mode and display each active wireless camera that has been set on the channel DIP switch located on the screen. In this mode, there is also an optional built-in function for wireless cameras with a built-in PIR motion detector. When the PIR detector senses motion, the screen s beeper will sound and display the image from that camera for a few seconds. The preset display time for each camera is 4 seconds but is adjustable between 2-30 seconds. To change this dwell time, press and hold both the Auto and Manual buttons simultaneously. The screen will beep depending on how long the buttons are pressed for. After releasing them, the screen will beep and the green LED on the AUTO button will flash with each beep. The total number of beeps and flashes indicate the new dwell time. 5.2.3 Scan Function (Optional function for PIR activated wireless cameras only) When the SCAN button is pressed, the whole system is placed in standby and the screen will appear blank. However the screen continues to scan through each active PIR wireless camera. If a camera senses motion, the screen s alarm will sound and the image from this camera will be displayed. After a further 4 minutes, the system will return to standby again and continue scanning. 5.3.4 Cam 1 to 3 Function By pressing any of the 3 CAM buttons corresponding to a PIR wireless camera, the PIR function of a camera can be enabled or disabled. The LED on the button pressed will turn green to indicate enabled. If pressed again, it will turn off to indicate it is disabled. 9
5.3 Volume Adjustment for A/V Input Source(s) The sound level of the audio from the screen can be adjusted by pressing the + or - button on the Volume/Adjust button. 5.4 General Screen Settings Press the Menu button to cycle through the following settings: Alarm volume Contrast Brightness Colour Tint Updown Mirror - adjust by pressing the + or - button on the Volume/Adjust button. - adjust by pressing the + or - button on the Volume/Adjust button. - adjust by pressing the + or - button on the Volume/Adjust button. - adjust by pressing the + or - button on the Volume/Adjust button. - adjust by pressing the + or - button on the Volume/Adjust button. - if the screen is mounted upside down, this function must be enabled to view the picture correctly in this mounted position. - this function is used for vehicle reversing Cameras. The screen will act as a rear view mirror when this function is enabled. 10
MAINTENANCE Section 6 Clean the LCD screen using a soft damp cloth. Replace the battery in the remote control once every 2 years. CR2025 type coin cell battery or any equivalent type. Only use a Lithium 3V TROUBLE SHOOTING Section 7 PROBLEM No camera picture on the screen SOLUTION Check all connections are made correctly. Ensure the camera(s) and monitor are plugged in and switched ON. Ensure the wireless camera(s) and screen are set to the correct channel(s). Interference on the camera picture Ensure each wireless camera is within the 100m range, and that no large obstructions are blocking the signal. Try repositioning the camera, screen or both to improve the reception quality. If necessary locate closer to each other. Reposition other nearby equipment transmitting on the 2.4 GHz frequency. Ensure no more than one wireless camera is set on the same camera channel. Audio problems when using the A/V ports Check all audio connections to the screen. Ensure the volume is turned up sufficiently on the screen. 11
ACCESSORIES IN THE RANGE Section 8 There are a range of accessories available in the Response CCTV product range to expand your system: CWK1 CA1 CWFK1 CA3 CA5 CA6 CA7 CA8 CA9 CA10 CA11 CA4 CA12 Wired Colour Camera CCTV Kit 2 Channel Digital Video Image Recorder Wireless Colour Camera CCTV Kit Wireless Colour Accessory Camera (requires CWFK1 CCTV KIT to operate) Professional Heavy Duty Camera CCTV Kit Dummy Professional Heavy Duty Camera 4 Channel DVR Recorder Kit Wired Internal Colour Dome Camera CCTV Kit Dummy Internal Dome Camera Heavy Duty Colour Camera CCTV Kit Dummy Heavy Duty Camera 10m Extension Cable Kit 20m Extension Cable Kit Note: The maximum extension cable length for any wired camera with this system is 30m without reducing the picture quality of the video. 12
TECHNICAL SPECIFICATION Section 9 ITEM TV system Frequency range Screen size Resolution Power supply PROFESSIONAL HEAVY DUTY CAMERA PAL or NTSC standard 2.41 to 2.47GHz 7.0 inch 1440 x 234 dots 480 horizontal lines minimum DC 9V, 2.0 A Brightness 300cd/m 2 Contrast rate 150 : 1 Colour configuration Channels Built-in speakers RGB stripe, full colour 3 x wireless A/V input 2 x wired input 2 x wired A/V output 2 x 0.5W (stereo) Operating temperature - 10 C to 40 C IP rating IP40 (dry internal use only) Power supply Screen 9VDC power supply adaptor Remote Control 1 x CR2025 3V Lithium cell Dimensions (H x W x D) 116.8 x 180.3 x 33mm 13
APPENDIX Section 10 Screen Mounting Guide: 118.8mm 14
DISPOSAL RECYCLING INSTRUCTIONS Section 11 Directive (2002/96/EC) This product is classified by the Waste Electrical or Electronic Equipment (WEEE) Directive. It should not be disposed of with other household or commercial waste. At the end of its useful life the packaging and product should be disposed of via a suitable recycling centre. For information on available facilities, please contact your local authority or the retailer from where the product was purchased. Batteries and waste electrical products should not be disposed of with household waste. Please recycle where these facilities exist. Check with your local authority or retailer for recycling advice. 15
GUARANTEE Section 12 Novar ED&S undertakes to replace or repair at its discretion goods (excluding non rechargeable batteries) should they become defective within 1 year solely as a result of faulty materials and workmanship. If the product has not been installed, operated or maintained in accordance with the instructions, has not been used appropriately or if any attempt has been made to rectify, dismantle or alter the product in any way the guarantee will be invalidated. The guarantee states Novar ED&S entire liability. It does not extend to cover consequential loss or damage or installation costs arising from the defective product. This guarantee does not in any way affect the statutory or other rights of a consumer and applies to products installed within UK and Eire only. If an item develops a fault, the product must be returned to the point of sale with: 1. Proof of purchase. 2. A full description of the fault. 3. All relevant batteries (disconnected). Response is a trademark of Novar ED&S. CUSTOMER HELPLINE Most issues can be solved over the phone in a few minutes. Please contact our Helpline Team on the number below for any installation and general advice regarding our products: 0844 736 9149 Lines open 9.00am to 5.00pm, Monday to Friday. Calls charged at service providers national rate. Novar Electrical Devices and Systems Limited. (A Honeywell Company) The Arnold Centre, Paycocke Road, Basildon, Essex SS14 3EA. UK www.friedland.co.uk Novar Electrical Devices and Systems Limited. 2009 50043922 Rev.B