Exam #1 Name Instructions. This exam is worth 100 points. The points allocated to each section are indicated at the beginning of the section. Some sections allow a choice as to which questions are answered. For these sections, do not answer more parts than requested. If all parts are answered, consecutive questions will be graded beginning with the first part. In calculations, be sure to report your answer with the correct number of significant figures. velocity of light in a vacuum: 3.00x10 8 m/sec Planck's constant: 6.626x10-34 Joule-sec electron charge: 1.602x10-19 Coulomb 1 Joule = 1 Volt-Coulomb Avogadro's constant: 6.022x10 23 atoms/mole 1 nm = 10-9 m 1 cm = 10-2 m 1 mm = 10-3 m 1 µm = 10-6 m s = [3(y i -yg) 2 /(n-1)] ½ yg = 3y i /n confidence interval = ts/n ½ s r = [3(y i -y^i) 2 /(n-2)] ½ y^i = mx i + b λν = c νg = 1/λ E = hν T = P/P 0 A = -log 10 (T) A = εbc A LOD = b + 3s r C LOD = 3s r /m C LOQ = 10s r /m n q = c / v q (q = medium) sin r = nλ/d - sin i sin i / sin r = n 2 / n 1 Physical Constants and Conversion Factors Equations
1. (40 points) Circle the correct answer for ten of the following: a. The precision of an analytical measurement (1) is described by calculating percent relative error. (2) is related to the width of the population distribution of the measurement. (3) is guaranteed to be high if the measurement also has high accuracy. b. The term "wavenumber" (1) refers to the number of waveform cycles traveled by a photon in a fixed time. (2) refers to a quantity often expressed in cm -1. (3) refers to the product of frequency and Planck's constant. (4) refers to the distance corresponding to one cycle of a waveform. c. An instrument used to measure transmittance (1) must have a monochromator. (2) must have a detector for measuring light intensity. (3) must have the ability to ratio the light intensities measured with and without the sample. (4) all of the above. d. The Beer-Lambert Law (1) states that transmittance is linearly related to concentration. (2) requires that the product of absorptivity and pathlength be known before absorbance can be related to concentration. (3) requires that absorptivity be independent of wavelength. (4) cannot be used if more than one absorbing species is present in a sample. e. A D 2 arc lamp (1) provides a continuous output in the infrared spectral region. (2) is based on the flow of current through a tungsten filament. (3) uses iodine to prevent the darkening of the lamp envelope. (4) is based on ultraviolet light emission from excited D 2 species.
f. A least-squares analysis using the model y^ = mx + b (1) is based on the calculation of m and b such that the sum of squared errors is a maximum. (2) seeks values of m and b that will produce the smallest value of the standard error of estimate. (3) cannot be used with absorbance vs. concentration data due to limitations in the Beer-Lambert Law. g. A photon with a frequency of 6 10 14 cycles/sec is (1) an ultraviolet photon. (2) a visible photon. (3) an infrared photon. h. For an analysis in which the measurement signal is in Volts and the analyte is determined in units of mg/l, the limit of detection (1) is expressed in units of Volts (2) is expressed in units of mg/l (3) is expressed in units of L/mg (4) is expressed in units of Volt-L/mg i. Which of the following statements is false regarding the absorption of photons by molecules? (1) absorption of a photon results in a change in the energy state of the molecule. (2) there is a correspondence between the energy of the photon and the difference in energy between the initial and final energy states (i.e., the states before and after the absorption) of the molecule. (3) the energy associated with electronic transitions is greater than the energy corresponding to a vibrational transition. j. Infrared photons (1) can only be absorbed by molecules with a bond dipole. (2) can only be absorbed when the photon frequency matches a vibrational frequency of the molecule. (3) can only be absorbed when their energy matches the difference in energy between two vibrational states. (4) all of the above.
k. A globar (1) is a rod of SiC that is resistively heated to produce infrared light through emission of blackbody radiation (2) is based on the production of an electrical arc within a rod of crystalline SiC. (3) is a type of ultraviolet light source commonly used in spectroscopy. (4) employs a halogen gas to prolong its lifetime. 2. (40 points) Answer five of the following: a. Name three regions of the electromagnetic spectrum. b. A photon has an energy of 5.68 10-19 Joules. What is its wavelength in nm? c. Differentiate between single-beam and double-beam spectrometers.
d. Differentiate between the terms sensitivity and selectivity. e. A 1.0x10-4 M solution is placed in a 1.00 cm pathlength cell and the absorbance is measured as 0.113 at 400 nm and 0.166 at 450 nm. Given that the concentration and pathlength are identical, why does the absorbance change? f. Describe the mechanism by which infrared photons are absorbed.
3. (10 points) Compound X has an absorptivity of 703 g -1 cm -1 L. The transmittance of a solution of X is measured in a 1.00 cm pathlength cell and found to be 20.6%. Compute the concentration of the solution of compound X in g/l.
4. (10 points) A determination of Mg (AW=24.3) concentration (C, mg/l) in water based on an absorbance (A) measurement produced the following calibration model: A = 0.0191C + 0.0113 A 0.1145 g mineral sample was digested and diluted to 100.00 ml. A 7.00 ml aliquot of this sample was diluted to 100.00 ml and the absorbance of this solution was determined to be 0.203. Compute the weight percent of Mg in the original steel sample.