Aquatic Inventories Project: Methods for Stream Habitat Surveys. Conservation and Recovery Program Oregon Department of Fish and Wildlife

Aquatic Inventories Project: Methods for Stream Habitat Surveys Conservation and Recovery Program Oregon Department of Fish and Wildlife 2006

Methods for Stream Habitat Surveys Table of Contents Introduction 1 Reach 5 Unit 1 11 Unit 2 21 Wood 24 Riparian 26 Literature cited 30 Reach combination chart and checklist 33 Map detail example 34 Narrow and broad valley diagrams 35 Channel form diagrams 36 Equipment checklist 38 Examples of data forms and channel metrics schematic 39-53 Oregon Plan Appendix 1: Methods for Random Habitat Surveys 54 Oregon Plan Appendix 2: Fish Inventory Protocols 58 Oregon Plan Appendix 3: Amphibian Inventory Protocols 66 Fish Identification Guide 68

Methods for Stream Habitat Surveys Aquatic Inventories Project Conservation and Recovery Program: Oregon Department of Fish and Wildlife INTRODUCTION The Aquatic Inventories Project is designed to provide quantitative information on habitat condition for streams throughout Oregon. This information is used to provide basic information for biologists and land managers, to establish monitoring programs, and to direct or focus habitat restoration efforts. Development of an Aquatic Inventories Project began within the Oregon Department of Fish and Wildlife (ODFW) in 1989 with sponsorship by the Restoration and Enhancement Program. Drafting of stream survey methods and implementation of field work began in 1990. The conceptual background for this work came from the experience of project staff and from interactions with Oregon State University, forest industry, and USFS PNW research scientists (Bisson et al. 1982, Grant 1986, Everest et al. 1987, Hankin and Reeves 1988, Moore and Gregory 1989, and Gregory et al. 1991). Significant contributions and review of these methods were provided by ODFW research staff, and from consultation with ODFW and United States Forest Service (USFS) biologists working on similar programs. Members of the Umpqua Basin Fisheries Restoration Initiative and the Oregon Forest Industry Council have provided additional review and consultation. This methodology was designed to be compatible with other stream habitat inventories and classification systems (i.e., Rosgen 1985, Frissell et al. 1986, Cupp 1989, Ralph 1989, USFS Region 6 Level II Inventory 1992, and Hawkins et al. 1993). This compatibility is achieved by systematically identifying and quantifying valley and stream geomorphic features. The resulting matrix of measurements and spatial relationships can then be generalized into frequently occurring valley and channel types or translated into the nomenclature of a particular system. For example, information summarized at the reach level (valley width, channel type, slope, terrace height and width, sinuosity, width, depth, substrate, eroding banks, etc.) can be used to characterize the stream into one of the types described by Rosgen (1985) or to match the parameters collected in other quantitative (USFS) or historic (U.S. Bureau of Fisheries) surveys. Version 15.1, May 2006. Kelly Moore, Kim Jones, Jeff Dambacher, et al. Oregon Department of Fish and Wildlife, Aquatic Inventories Project, Conservation and Recovery Program, Corvallis, OR 97333. (541) 757-4263

2 The process of conducting a stream survey involves collection of general information from maps and other sources and the direct observation of stream characteristics in the field. This information is both collected and analyzed based on a hierarchical system of regions, basins, streams, reaches, and habitat units. Supervisors are responsible for collecting the general information on regions and basins and for directing the activities of the survey crews. Survey teams will collect field data based on stream, reach and channel unit characteristics. Region and basin data will primarily come from ODFW-EPA region and sub region classifications, and from map analysis. The following instructions and definitions provide the outline for these activities and a description of the tasks involved in conducting ODFW s stream habitat inventory. Each field crew is comprised of two people with each member responsible for specific tasks. The "Estimator" will focus on the identification of channel unit characteristics. The "Numerator" will focus on the counts and relative distribution of several unit attributes and will verify the length and width estimates for a subset of units. The "Estimator" and "Numerator" share the responsibility for describing reach characteristics, riparian conditions, identifying habitat unit types, and for quantifying the amount of large woody debris. Crew members may switch responsibility for estimator or numerator when they start a new stream. They will not, however, switch estimator and numerator jobs on the same stream. BASIN INFORMATION Basin information is gathered prior to and during the course of the survey. Some of this information (primarily map work and regional classification) must be collected in the office. Most of this information is not the responsibility of the field crews. However, relevant comments by the survey crews should be included in their Field Books and on the Data Sheets. These summaries are used to group and classify streams and to provide general information for the final stream reports. 1. Basin name. Use the name of the large river commonly used to describe a region. For example, use McKenzie R for Lookout CR, not Willamette or Columbia. 2. Stream name. Use a standardized system of the name followed by descriptors of forks etc. Examples: Alsea R, Drift CR, Lobster CR, E FK. Spell out descriptive or non-standard types such as Branch, Slough, or Swale. Spell out compass direction only for larger streams and when the usage is common, such as North Umpqua. Use the same name format on all data sheets. 3. Stream order, drainage area, and drainage density of the study stream. Determined from blue line tributaries (perennial and intermittent) shown on U.S.G.S. 7.5 minute topographic maps. 4. Elevation (m) at the confluence with the receiving channel and at the end of the survey (this can be obtained from the GPS unit when there is adequate satellite coverage). 5. ODFW-EPA Regions and Sub regions, geology, and soils of the basin.

6. Stream Flow. Identify the location of USGS or other gauging stations. The location and stage height at any gauging station, marked bridge, or staff gauge will also be recorded during the survey. 3 7. General community structure and size composition of riparian vegetation. Identified by separate census or sample in each basin. 8. Description of fish species and stocks present, management concerns, and linkage to other databases or research projects. 9. Flow Regulation: Description of existing or proposed dams and diversions influencing the basin and segment. 10. General description of land use and ownership in the basin (e.g. managed timber, rural residential, agricultural, livestock grazing). 11. Contacts. Names, addresses, and phone numbers of key people to contact with respect to survey. Include ODFW district biologists, interested private individuals, landowners contacted for access, etc. EQUIPMENT 1. Maps - 7.5 minute quad (1:24,000 scale) USGS topographic maps of the stream and basin. Road map coverage by county or fire district. Oregon Atlas and Gazetteer (Delorme Mapping). 2. Recording Materials - Waterproof field book, survey forms for each portion of the survey, waterproof paper, and pencils. 3. Clothes - Neoprene chest waders, wading shoes, and/or hip boots (non-slip soles of felt, studded corkers, outdoor carpet or similar material is advised), rainwear, snag and thorn proof clothing appropriate for the weather. 4. Two-meter-long staff (marked in meters and tenths), compass, 50 meter fiberglass measuring tape, day pack, polarized glasses, thermometers, clinometer, clipboard, vest, flagging, permanent markers, and digital camera, GPS unit. See equipment page in appendix for a more complete description of survey equipment.

4 MAP WORK Do not go into the field without a topographic map! Data that cannot be linked to the maps is essentially useless. Use the maps to orient to the stream and to identify the location of reach changes, named tributaries, roads, and bridge crossings. Mark all reach changes and important features on the map. Write the channel unit number on the map at the place that corresponds to the location of named tributary junctions, bridges, and other landmarks. Clearly mark where you start and end the survey. A good correspondence between landmarks on the map and the data collected is an essential part of our survey effort. Information from the surveys will be utilized and integrated with Geographic Information System (GIS) analysis. Well documented and accurate maps are required for this process. In addition to a well marked map, it is essential that the habitat survey follow the USGS named stream on the topo map, regardless of the amount of flow. An example of field entries on a topographic map is in the appendix (Page 32). If using a GPS unit, record the Easting and Northing UTM coordinates at the beginning of the survey, at all reach changes, at riparian transects, and at the end of all surveys. Also, make a note as to what coverage is obtained (2D or 3D). If 3D coverage is acquired, record the elevation in the notes. When reading the numbers from your GPS unit, the top number is the Easting coordinate and corresponds to small numbers along the top of your USGS quad map. The bottom number is the Northing coordinate and corresponds to similar numbers along the side of your USGS map. Your location should be where a vertical line from the Easting mark and a horizontal line from the Northing mark intersect. FIELD BOOK This is a very important piece data collection feature and should have daily entries. Maintain a succinct log of your activities in the field book. Each day, record the date and name of the stream where you worked. Enter the approximate distance covered and number of hours spent working on the stream. Keep track of your travel time separately. Record relevant details about access to the stream, contact people from cooperating industry or agency groups, and people you contact to gain permission to survey. Record the names and phone numbers of people you may contact as you complete the survey. Write a paragraph or so of general description for sections of each stream in the field book or on a separate stream report form. Pay particular attention to descriptions of the riparian zone, additional details concerning land use, or factors that influence the fish populations. This is the appropriate place to express your opinions. Other comments, sketches of complex features, suggestions, complaints, etc. are often useful.

5 PHOTOGRAPHS A good photographic record of the stream survey provides additional information and documentation. Take pictures that typify reach changes, riparian zones, and other stream characteristics as described in the following sections of these instructions. Be sure that the date-back feature of the camera is functioning correctly and to turn off the flash. For each picture, record the channel unit number, date, time, and a description of the subject on the Photo Record sheet. DATA SHEETS: REACH, UNIT-1, UNIT-2, WOOD, and RIPARIAN REACH FORM A reach is a length of stream defined by some functional characteristic. A reach may be simply the distance surveyed. More frequently, reaches are defined as: stream segments between named tributaries, changes in valley and channel form, major changes in vegetation type, or changes in land use or ownership. Enter a new line on the reach data sheet at any significant change in any one of the reach variables (valley type, channel form, adjacent landform, valley width index, vegetation, or land use) and/or at the confluence with tributaries named on 7.5 minute topographic maps. When a new reach is identified by a named tributary, write the name in the Reach Note column. Also describe a new reach if an unnamed tributary contributes significant flow (approx. 15-20% of the total). Do not invent names for unnamed tributaries, instead identify them as Trib. 1, Trib. 2, etc. and record them on the data sheet and the map. Changes in reach characteristics are used to verify survey location and to identify reach and stream segments within our basin classification system. Circle the variable that resulted in the new reach entry. Flagging is used to mark specific points during a survey. Hang a strip of plastic flagging at each reach change, named tributary junction, and at riparian transects. Mark the flagging with the unit number, unit type, date, and "ODFW-AQ.-INV.". These flags will be used to locate specific reaches and units for fish sampling and to link units and locations for repeat habitat surveys. Randomly selected stream segments will be selected for repeat surveys during the field season. Results will be compared to check on variability between crews and for habitat changes at different stream flow. The following sequence corresponds to the listing of variables on the data sheet: 1. Date. 2. Reach. The numbered sequence of reaches as they are encountered. Each reach is comprised of variable number of channel units. 3. Unit Number. Sequence number of the first unit recorded. 4. Channel Form. Determined by the morphology of the active channel, hill slopes, terraces, and flood plains. Identify the channel form and enter the appropriate two-letter code in this column.

Refer to Valley and Channel Classification in the appendix for definitions, allowable combinations, and examples. 6 First look at the ratio of the active channel width to the valley width to determine the Valley Width Index (see pg. 7, # 6). This ratio determines if you are in a broad or narrow valley floor type. If the VWI is 2.5 or less you have a narrow valley type and if the VWI is greater than 2.5 you have a broad valley type. Next, look at the types of land forms adjacent to the stream channel to characterize and complete your classification. The channel is constrained when adjacent landforms restrict the lateral movement of the channel. In constrained channels, stream flows associated with all but the largest flood events are confined to the existing channel configuration. Narrow Valley Floor Types (VWI 2.5)---Always constrained, defined by the characteristics of the constraining feature. CB CH CF Constrained by Bedrock (bedrock dominated gorge) Constrained by Hill slope Constrained by alluvial Fan Broad Valley Floor Types (VWI > 2.5)---The valley is several times wider than the active channel. The channel, however, may be either unconstrained or constrained depending on the height and configuration of the adjacent landforms. 1. Unconstrained Channel (terrace height is less than the flood prone height* and the floodprone width* is > than 2.5X active channel width). Low terraces, overflow channels, and flood plains adjacent to the active channel. US UA UB Unconstrained-predominantly Single channel. Unconstrained-Anastomosing (several complex, interconnecting channels) Unconstrained-Braided channel (numerous, small channels often flowing over alluvial deposits) 2. Constrained Channel (terrace height is greater than the flood prone height*). Adjacent landforms (terraces, hillslopes) are not part of the active flood plain. CT CA CL Constraining Terraces. (terrace height > floodprone height and floodprone width < 2.5 X active channel width). Constrained by Alternating terraces and hill slopes. Same rule for terrace height but the channel may meander across the valley floor. The stream channel is confined by contact with hill slopes and high terraces. Constrained by Land use (road, dike, landfill) * See page 20 for floodprone height and width definitions.

5. Valley Form. General description of the valley cross section with emphasis on the configuration of the valley floor. Divided into types with a narrow valley floor (valley floor width (VWI) 2.5 times stream active channel width (ACW) and types with a broad valley floor (VWI > 2.5 times ACW). 7 Narrow Valley Floor (VWI < or = 2.5) see page 33 for examples: SV Steep V-Shaped valley or bedrock gorge (side slopes >60 o ). MV Moderate V-Shaped valley (side slopes > 30 o, <60 o ). OV Open V-Shaped valley (side slopes <30 o ). On rare occasions where you might encounter a different classification on each side of the stream, record only one on the reach sheet and make a note of the other in the note column. Broad Valley Floor (VWI > 2.5) see page 33 for examples: CT MT WF Constraining Terraces. Terraces typically high and close to the active channel. Terrace surface is unlikely to receive flood flows and lacks water dependent (hydrophilic) vegetation. Multiple Terraces. Surfaces with varying height and distance from the channel. High terraces may be present but they are a sufficient distance from the channel that they have little impact. Wide-Active Flood plain. Significant portion of valley floor influenced by annual floods, and has water dependent vegetation (mesic meadow). Any terraces present do not impinge on the lateral movement and expansion of the channel. Valley Form and Channel Form are related and can only occur in certain combinations. Possible combinations are shown on page 31, Table 1. 6. Valley Width Index. Ratio of the width of the active stream channel to the width of the valley floor. The Valley Width Index (VWI) is estimated for the reach by dividing the average active channel width into the average valley floor width (see diagram on page 20). In practice, the number of active channels that could fit across the valley floor. Also entered on UNIT 1 sheet at verified units. Do not start a new reach for minor changes in valley width index. However, always start a new reach when the channel changes from VWI < 2.5 to VWI > 2.5; or VWI > 5. When the valley width changes repeatedly within a short distance, select an average value for the VWI. For example, when the valley floor gradually widens from a hillslope constrained reach to a broad valley reach, make one reach change, not new reach designations every few channel units. It is possible to have an unconstrained channel but a VWI of 1. This may occur in some meadow reaches and other

situations where the multiple channels and the floodplain spread across the entire valley floor. 8 Observations of valley floor surfaces and characteristics can be done as part of the riparian vegetation survey. Getting out of the stream channel will help you to accurately estimate VWI, identify floodplain and terrace surfaces, and to classify reach types. 7. Streamside Vegetation (Veg Class). A two-letter code based on the composition of riparian zone vegetation. Definitions of the riparian zone differ. Generally, we consider the vegetation observed in the area within one active channel width of either side of the channel to represent the riparian zone. The first letter identifies the plant community. The second part of the code will refer to the size of trees within identified dbh classes. Do not enter a size or age class for shrubs, brush, or grasses. Example: riparian zone with 15-30 cm diameter alder = D15. Separate entries are made for the dominant and subdominant plant communities as estimated from crown density. (Note: In some instances grass can be the dominant plant taxa). Example: C30 (dominant) and G (subdominant) in ponderosa pine/grass communities. Vegetation Type: N B G P S D M C No Vegetation (bare soil, rock) SageBrush (sagebrush, greasewood, rabbit brush, etc.) Annual Grasses, herbs, and forbs. Perennial grasses, sedges, rushes, and ferns Shrubs (willow, salmonberry, some alder) Deciduous Dominated (canopy more than 70% alder, cottonwood, big leaf maple, or other deciduous spp.) Mixed conifer/deciduous (approx. a 50:50 distribution) Coniferous Dominated (canopy more than 70% conifer) Size Class. Use groupings for the estimated diameter at breast height (dbh) expressed in centimeters of the dominant trees. Estimate diameter of young conifers below the first whorl of branches. Enter just the first number(s) of any choice. 1-3 Seedlings and new plantings. 3-15 Young established trees or saplings. 15-30 Typical sizes for second growth stands. West side communities may have fully closed canopy at this stage. 30-50 Large trees in established stands. 50-90 Mature timber. Developing understory of trees and shrubs. 90+ Old growth. Very large trees, nearly always conifers. Plant community likely to include a combination of big trees, snags, down woody debris, and a multi-layered canopy. These size classes correspond to dbh estimated in inches of: <1, 1-5, 6-11, 12-20, 21-35, and 36+ respectively.

8. Land Use. Determined from observations of terraces and hill slopes beyond the riparian zone. Code subdominant land use where appropriate. Separate entries for the dominant and subdominant land uses (i.e. PT (dominant) and HG (subdominant) = Partial cut Timber and Heavy Grazing). If a code listed below does not adequately describe a land use, use the most appropriate and make a note. DO NOT make up new codes. 9 AG TH YT ST LT MT OG PT FF BK LG HG EX GN UR RR IN DW CR GF MI WL NU WA AGricultural crop or dairy land. Timber Harvest. Active timber management including tree felling, logging, etc. Not yet replanted. Young Forest Trees. Can range from recently planted harvest units to stands with trees up to 15 cm dbh. Second growth Timber. Trees 15-30 cm dbh in generally dense, rapidly growing, uniform stands. Large Timber (30-50 cm dbh) Mature Timber (50-90 cm dbh) Old Growth Forest. Many trees with 90+ cm dbh and plant community with old growth characteristics. Partial cut Timber. Selection cut or shelterwood cut with partial removal of large trees. Combination of stumps and standing timber. If only a few live trees or snags in the unit, describe in note column. Forest Fire. Evidence of recent charring and tree mortality. Bug Kill. Eastside forests with > 60% mortality from pests and diseases. Enter bug kill as a comment on the unit sheet when it is observed in small patches. Light Grazing Pressure. Grasses, forbs and shrubs present, banks not broken down, animal presence obvious only at limited points such as water crossings. Cow pies evident. Heavy Grazing Pressure. Broken banks, well established cow paths. Primarily bare earth or early successional stages of grasses and forbs present. EXclosure. Fenced area that excludes cattle from a portion of rangeland GreeN way. Designated Green Way areas, Parks (city, county, state). URban Rural Residential Industrial Domestic Water supply watershed. Conservation area or wildlife Refuge. GolF course. MIning WetLand. No Use identified. Designated Wilderness Area 9. Water Temperature. Stream temperature recorded at each reach change or a minimum of once per page of data. Record the time as well. Note if the temperature is measured in o C or o F. At named tributaries, record the stream temperature of the tributary and in the mainstem stream upstream from the confluence of the tributary. Identify and record each temperature in the appropriate line of the Unit 1 Note column.

10 10. Stream Flow. Description of observed discharge condition. Best observed in riffles. If a gauging station is present, be sure to record the stage height. DR PD LF MF HF BF FF DRy Puddled. Series of isolated pools connected by surface trickle or subsurface flow. Low Flow. Surface water flowing across 50 to 75 percent of the active channel surface. Consider general indications of low flow conditions. Moderate Flow. Surface water flowing across 75 to 90 percent of the active channel surface. High Flow. Stream flowing completely across active channel surface but not at bankfull. Bankfull Flow. Stream flowing at the upper level of the active channel bank. Flood Flow. Stream flowing over banks onto low terraces or flood plain. 11. Location. Township, range, section and quarter at the start of the reach. Use the following example as the format: T10S-R5W-S22SE. 12. Photo Number and Time. Take a photograph that shows the stream and riparian zone at each reach change. Record the exposure number and the time shown on the camera on the reach sheet and the photo record sheet. 13. Reach Note. Additional space for comments, names of tributaries, land ownership, and reach start location. Abbreviate by ownership code or use names of forest, timber companies, ranches, etc. when known. P M C T GN FW BL SF NF US WA Private Municipal County Tribal GreeNway Oregon Department of Fish and Wildlife Bureau of Land Management State Forest National Forest US Fish and Wildlife Service Wilderness Area 14. Sketch. Make a sketch of the channel and valley cross section for each reach in one of the boxes provided on the reach form. Identify the reach number in the box. Label and give approximate measurements and dimensions for important features. 15. Record GPS UTM coordinates. Note the coverage (2D or 3D) and the elevation.

UNIT-1 FORM 11 The Estimator member of the field crew completes this data sheet. Crews work upstream, identifying and characterizing the sequence of habitat units. At tributary junctions: Tributary channel junctions (confluence with a tributary) are identified and surveyed, regardless of flow. Note with comment code on the Unit 2 sheet; record the active channel width and temperature of the tributary in the note column. Refer to the topo map and indicate the trib referencing the unit number into which the tributary flows. At each channel junction, estimate the percent of total flow in each channel. Proceed up the named stream on the USGS topographic map regardless of flow. If neither channel is named, proceed up that with the greatest flow. Survey the portion of tributaries that flow across the active channel up to the bank full level. Tributary channel units will be numbered and sequenced from the point where the tributary enters the main channel. Be sure to use the proper channel type code. Survey and record a minimum of one unit for each tributary and additional units (if applicable) that would become part of the main channel at bankfull flow. A tributary differs from a spring seep because it will have a defined channel. Spring seeps are not surveyed, yet are noted in the notes column. In braided channels: Continue upstream, always taking the channel with the greatest flow, until reaching the unit where the stream again forms a single channel. Backtrack, and then survey the sequence of units in the secondary channel, then the sequence of units in the tertiary channel, etc. For particularly complex areas, make a simple sketch in the field book showing the sequence and locations of channel units (type and number). 1. Reach. The number of the reach; links unit data to reach data. 2. Unit. The sequential number describing the order of channel habitat units. A reach is comprised of many channel units. 3. Unit Type. The concept of a channel habitat unit is the basic level of notation for our survey methodology. We subdivide the stream into two general classes of unit types: channel geomorphic units and special case units. Channel geomorphic units are relatively homogeneous lengths of the stream that are classified by channel bed form, flow characteristics, and water surface slope. With some exceptions, channel geomorphic units are defined to be at least as long as the active channel is wide. Individual units are formed by the interaction of discharge and sediment load with the channel resistance (roughness characteristics such as bedrock, boulders, and large woody debris). Channel units are defined (in priority order) based on characteristics of (1) bedform, (2) gradient, and (3) substrate.

12 Special case units describe situations where, because of stream flow level or a road crossing, the usual channel geomorphic unit types do not occur. Special case units include dry or partly dry channels, and culverts. GEOMORPHIC CHANNEL UNITS Characteristic water surface slopes are given for each group of habitat unit types. However, channel bed form and flow characteristics are the primary determinant of unit classification. Use the unit s slope to help make determinations when the other characteristics are ambiguous. POOLS (water surface slope always zero) PP SP LP TP DP BP Plunge Pool: Formed by scour below a complete or nearly complete channel obstruction (logs, boulders, or bedrock). Substrate is highly variable. Frequently, but not always, shorter than the active channel width. Straight scour Pool: Formed by mid-channel scour. Generally with a broad scour hole and symmetrical cross section. Lateral scour Pool: Formed by flow impinging against one stream bank or partial obstruction (logs, root wad, or bedrock). Asymmetrical cross section. Includes corner pools in meandering lowland or valley bottom streams. Trench Pool: Slow flow with U or V-shaped cross section typically flanked by bedrock walls. Often very long and narrow with at least half of the substrate comprised of bedrock. Dammed Pool: Water impounded upstream of channel blockage (debris jams, rock landslides). Beaver dam Pool: Dammed pool formed by beaver activity. In most cases this will be preceded by a SD (step over beaver dam). SUBUNIT POOLS Alcoves, backwaters, and isolated pools are types of habitat subunits; generally not as long as the full channel width. They are, however, generally easy to identify and are important habitat types. Alcoves, backwaters, and isolated pools are formed by eddy scour flow near lateral obstructions. AL ALcove: Most protected type of subunit pool. Alcoves are laterally displaced from the general bounds of the active channel. Substrate is typically sand and organic matter. Formed during extreme flow events or by beaver activity; not scoured during typical high flows.

13 BW Backwater Pool: Found along channel margins; created by eddies around obstructions such as boulders, root wads, or woody debris. Part of active channel at most flows; scoured at high flow. Substrate typically sand, gravel, and cobble. IP Isolated Pool: Pools formed outside the primary wetted channel, but within the active channel. Isolated pools are usually associated with gravel bars and may dry up or be dependent on inter-gravel flow during late summer. Substrate is highly variable. Isolated pool subunits do not include pools of ponded or perched water found in bedrock depressions. GLIDES GL GLide: An area with generally uniform depth and flow with no surface turbulence. Low gradient; 0-1 % slope. Glides may have some small scour areas but are distinguished from pools by their overall homogeneity and lack of structure. Generally deeper than riffles with few major flow obstructions and low habitat complexity. There is a general lack of consensus regarding the definition of glides (Hawkins et al. 1993). RIFFLES RI RP RIffle: Fast, turbulent, shallow flow over submerged or partially submerged gravel and cobble substrates. Generally broad, uniform cross section. Low gradient; usually 0.5-2.0% slope, rarely up to 6%. Riffle with Pockets: Same flow and gradient as Riffle but with numerous sub-unit sized pools or pocket water created by scour associated with small boulders, wood, or stream bed dunes and ridges. Sub-unit sized pools comprise 20% or more of the total unit area. RAPIDS RB RR Rapid with protruding Boulders: Swift, turbulent flow including chutes and some hydraulic jumps swirling around boulders. Exposed substrate composed of individual boulders, boulder clusters, and partial bars. Moderate gradient; usually 2.0-4.0% slope, occasionally 7.0-8.0%. Rapid over BedRock: Swift, turbulent, "sheeting" flow over smooth bedrock. Sometimes called chutes. Little or no exposed substrate. Moderate to steep gradient; 2.0-30.0% slope. Low gradient bedrock, similar to a riffle, is considered RR.

14 CASCADES CB CR Cascade over Boulders: Much of the exposed substrate composed of boulders organized into clusters, partial bars, or step-pool sequences. Fast, turbulent, flow; many hydraulic jumps, strong chutes, and eddies; 30-80% white water. High gradient; usually 3.5-10.0% slope, sometimes greater. Cascade over BedRock: Same flow characteristics as Cascade over Boulders but structure is derived from sequence of bedrock steps. Slope 3.5% or greater. STEPS Steps are abrupt, discrete breaks in channel gradient. Steps are usually much shorter than the channel width. However, they are important, discrete breaks in channel gradient with gradients. Steps can separate sequential units of the same type. For example, small steps (<0.3m high) that separate pools may be important features in very low gradient reaches and should be recorded as individual habitat units. Low steps (<0.3m high) in moderate to high gradient reaches formed by gravel and small cobbles on the face of transverse bars can usually be included in the next fast water unit upstream. Steps are classified by the type of structure forming the step. SR SB SC SL SS SD Step over BedRock (include hardpan and clay steps) Step over Boulders Step over face of Cobble bar Step over Log(s), branches Step created by Structure (culvert, weir, artificial dams) Step created by Beaver Dam Record the estimated height of the step in the note column and take a picture of any steps that are potential barriers to fish passage. (Note: always record a step height in the note column for the SS unit type regardless if a passage problem cannot be determined).

15 SPECIAL CASE UNIT TYPES DU PD DC Dry Unit: Dry section of stream separating wetted channel units. Typical examples are riffles with subsurface flow or portions of side channels separated by large isolated pools. Record the length, active channel width (acw), and unit data. Count boulders w/in acw. PuDdled: Nearly dry channel but with sequence of small isolated pools less than one channel width in length or width. Record all unit data. Record the average wetted width and modal depth. Note the acw and any deep pockets in the NOTE field. Dry Channel. Section of the main channel or side channel that is completely dry at time of survey. Record all unit data, use active channel width for width. Count boulders w/in acw. Depth = zero. Note: For all three special case unit types, break out dry or puddled step unit types that are potential barriers to upstream migration as individual units. Record the height and type as it would appear if wetted (see STEP section above). CC Culvert Crossing. Stream flowing through a culvert. Record all data for metal bottom culverts. However, record the substrate of the surrounding fill material when estimating the composition of substrate material. Record the height from the culvert lip to the stream surface (drop), diameter, material, and shape of culvert in the note column. Take a picture of any culvert that is a potential fish barrier. If possible, have a depth staff or person in the photo to reference the step height. All Culvert Crossing unit types should have a Step Structure unit type immediately preceding it unless there is absolutely no drop to the water below. If a drop exists, record a step height in the note column regardless of the height. Write no drop in the note column if a drop does not exist.

16 4. Channel Type. Channel ordering code based on channel by size and location. Orders the sequence of single, multiple, and side channels. 00 No Multiple Channels (all flow in one channel) 01 Primary Channel (of multiple channel reach or in the unit where a tributary enters the channel) 02 Secondary Channel (of multiple channel reach) 03 Tertiary Channel (of multiple channel reach) Continue pattern for 04, 05, 06 level channels. 10 Isolated Pools, Alcoves, or Backwater Pools. 11 Primary channel of valley floor tributary. If the tributary has a name, write it in the note column. 12 Secondary channel of valley floor tributary. UNIT NUMBER UNIT TYPE CHANNEL TYPE % FLOW 1 RI 00 100 2 LP 00 100 3 RB 01 90 4 RI 11 10 5 PP 11 10 6 RI 01 90 7 CB 01 80 8 RB 01 80 9 RI 01 90 10 LP 01 90 11 RI 02 10 12 LP 02 10 13 RB 02 10 14 RI 03 10 15 RP 03 10 16 RI 04 5 17 IP 10 0 18 CB 00 100

It is very important that the primary channel be identified with the proper code. This information is used in a critical step of the data analysis to calculate channel length and sinuosity. The inventory considers the stream as the system of all channels that transport water down the drainage. The intention is to survey and quantify all aquatic habitats located within the valley floor. All active channels and unit types will be classified with a channel code and an estimate of the percent of total flow carried in each channel. 17 5. Percent Flow. Visual estimate of the relative amount of flow in the channel, in each channel where multiple channels occur, or the contribution to total flow from a tributary. Record 0% for alcove, backwater, and isolated pool unit types. For dry unit types don t try to estimate what the percentages would be if water were present record 100% in the 00 or 01 channel unit(s) and 0% for the 02 channel unit(s). This is difficult to measure accurately. In the past, crews have tended to overestimate the contribution from tributaries. Don't be concerned about balancing your totals for flow to 100 percent. The information is used only to identify the relative contribution or distribution of flow. Record the active channel width (ACW) of the tributary in the note column as well. 6. Unit Length. Length of each unit in meters. The length is estimated every unit; it is estimated and verified every 10th unit. To estimate the length of very long units, subdivide into lengths you are comfortable estimating and add them together. Do not pace the length of the unit. Except in very rare cases, no unit should be more than 100 to 150 meters long (with Oregon Plan surveys the maximum length of a unit will be 25m. for the 500 meter sites and 50m. for the 1000 meter sites). Long units can usually be divided at points where the stream changes direction. When long units turn corners of the stream, create a new unit before the upstream member of the crew disappears from view. Back-to-back units of the same type are acceptable when following this "line of sight" rule. Use gradient changes to identify breaks in unit lengths. Use equal effort to make good estimates on all units. Use the same technique on all units. Do not try to estimate more carefully on units you know will be verified. 7. Unit Width. Width of wetted channel (estimated every unit; estimated and verified every 10th unit). Measure the average width of the entire unit. On multiple wetted channel units, such as steps over bedrock where there are several wetted slots carved into the rock, record the sum of the wetted widths.

Slope. Gradient of water surface in the unit. Expressed as the percent change in elevation over the length of the unit. Estimated with a clinometer using the scale on the right side in the viewfinder. 18 8. Channel Shade. (Shade Left and Shade Right on data sheet). Measured with the clinometer as the degrees (left side in the viewfinder) above horizontal to the top of riparian vegetation or land forms (<90 o ). Measured perpendicular to the channel unit on the left and right banks (see diagram below and on page 30). This variable requires integration of topographic shading and canopy closure.

10. Active Channel Height. Vertical distance from the streambed to the top of the active channel. Determined by averaging the cross-section measurements of the water depth of fast water units or at pool tail crest of pools and adding it to the distance from water surface to the top of the active channel. Measure the height at every 10th unit and at change in reach type. 11. Active Channel Width. Distance across channel at "bank full" flow. Bankfull flow is the level the stream flow attains every 1.5 years on average. The boundary of the active channel can be difficult to determine; use changes in vegetation, slope breaks, or high water marks as clues. Sum the width of all active channels in multichannel situations. Measure the active channel width every 10th unit when verifying estimates and at start of new reaches. 19 The key indicator of bankfull stage (active channel) is the floodplain: a flat depositional surface adjacent to the channel and at the top of point bars. 12. Floodprone Height. The floodprone height is determined by doubling the active channel height. The floodprone height is the maximum depth in the channel during a flood event occurring approximately every 50 years. Record twice the active channel height as the floodprone height to the nearest 0.1 meter. Measure the floodprone height every 10th unit when verifying estimates and at start of new reaches. 13. Floodprone Width. Distance across the stream channel and/or unconstraining terraces at floodprone height. The floodprone width is the width of the valley floor inundated during a flood event occurring approximately every 50 years. Measure the floodprone width every 10th unit when verifying estimates and at start of new reaches. If the floodprone width is greater than 4 times the active channel width at that location, simply estimate the floodprone width. The ratio of floodprone width to active channel width is necessary to determine the reach type and entrenchment ratio. 14. Terrace Height. The height from the streambed to the top of the high terrace. A high terrace is defined as the first terrace you encounter above the floodprone height. Measure every 10th unit and at reach changes. 15. Terrace Width. This is the inter-terrace distance measured from the first high terrace lip, across the stream channel, to the corresponding terrace lip on other side of the stream (TW in diagram below) or to the hillslope if a matching terrace lip does not exist. Measure a terrace width and height if the following two conditions exist: 1) The terrace height is greater than the floodprone height AND 2) The terrace width is less than 4 times the active channel width. In multichannel situations, sum the inter-terrace width of all channels. Measure at every 10th unit (except for Oregon Plan surveys see Appendix 1) and at start of new reaches.

20 16. VWI Valley Width Index. Same method as on the reach sheet (page 7). Additional estimates improve accuracy of average value. Draw a cross section of the transect above the measurements on the data sheet (see example sheets in the appendix). Indicate the valley width and VWI estimate on the drawing. Refer to diagrams below and in the appendix for illustrations of active channel, floodprone, and terrace measurements. 17. Note. Any pertinent additional information or items of interest (fish or wildlife observed, evidence of pollution or illegal dumping, description of channel structure, names of roads or tributaries, etc.).

UNIT-2 FORM 21 Information recorded by the "Numerator" member of each field crew. 1. Unit Number. Corresponds to number on "Estimator" sheet. 2. Unit Type: Corresponds to same type on "Estimator" sheet. 3. Depth. Maximum depth in pools, modal or typical depth in glides and fast water units. Measure to the nearest 0.05 meter as accurately as possible in pools. Probe the bottom with the depth staff to find the deepest point. Small differences in pool depth are significant. 4. Depth at Pool Tail Crest: Measure the maximum depth to the nearest 0.01 meter at the pool tail crest (PTC) for every pool habitat unit. For subunit pools (BW, AL, IP), a PTC does not need to be measured or recorded. The PTC location is where the water surface slope breaks into the downstream habitat unit. Measure the deepest point along the hydraulic control feature that forms the pools. For beaver ponds unit type (BP) that have no water flowing over the top of the dam yet there is subsurface flow through the sticks and logs of the dam, record the PTC depth as 0.01 meter. 5. Verified Length and Width. The measured length and width of the habitat unit. Taken at every 10th unit and called "verified units" because the actual measurements are used to calibrate the estimates made on each unit. Where a particular unit type is rare, additional measurements may be necessary; simply write in the values over the shaded part of the data sheet. Remember to hang a flag at every third verified unit. 6. Substrate. Percent distribution by streambed area of substrate material in six size classes: silt and fine organic matter, sand, gravel (pea to baseball; 2-64mm), cobble (baseball to bowling ball; 64-256mm), boulders, and bedrock. Estimate distribution relative to the total area of the habitat unit (wetted area). Round off each class to nearest 5 percent Do not worry about totaling your estimates to 100 percent; this will be done during analysis. Be sensitive to the difference between surface flocculants and other fine sediment. Fine sediment that covers and embeds gravel and cobble should be part of your estimate. A thin layer of low density fine material over bedrock or boulders should not be included. Hardpan clay or conglomerate substrate has bedrock characteristics and is therefore classified as bedrock when estimating percent composition. Estimate the distribution of the surrounding and/or supporting substrate to the best of your ability at SL (step over log) and CC (culvert crossing) units. For open bottom culverts, estimate the substrate as you would a normal habitat unit. 7. Boulder Count. Count of boulders greater than 0.5 m in average diameter. Within this size class, include only the boulders that have any portion protruding above the water surface and those at the margin of the wetted channel. In dry units and dry channels, estimate the boulder count within the active channel.

8. Percent Actively Eroding Bank. Estimate the percent of the lineal distance of both sides of the habitat unit that is actively eroding at the active channel height. Active erosion is defined as actively, recently eroding, or collapsing banks and may have the following characteristics: exposed soils and inorganic material, evidence of tension cracks, active sloughing, or superficial vegetation that does not contribute to bank stability. 9. Percent Undercut Bank. An estimate of the percent of the perimeter of the habitat unit composed of undercut banks. Estimate at the margins of the wetted channel as an index of cover habitat. Look for areas that provide good hiding cover for fish. Typically, if the undercut portion extends along the bank for a meter or more, include it in your estimate. Include areas undercut beneath root wads. 10. Comment Codes. Comments identifying important features. Enter as many codes as appropriate. Separate items that apply to the left bank (looking upstream) from those for the right bank using a slash (/). If a code does not exist for an observation, do not invent a code. Write a description in the note column if necessary. 22 BC BD BK BV CC CE CS DJ FC GS HS MI PA PN Bridge Crossing. Record road name or number in note. Beaver Dam. Helps to identify steps created by beavers. Bug Kill. Patches of insect or disease tree mortality. BeaVer Activity (beaver den, cut trees, etc.) Culvert Crossing. Same as Bridge Crossing except the stream passes through a culvert. Record road name or number. Culvert Entry. Tributary entering through culvert. Record diameter, length, slope, and height of drop. Channelized Streambanks. Rip-rap or other artificial bank stabilization and stream control. Debris Jam. Accumulation of large woody debris that fills the majority of the stream channel and traps additional debris and sediment. These features tend to have potential to alter channel morphology. Fence Crossing. Gauging Station. Artificial Habitat Structure. Describe type: gabion, log weir, cabled wood, interlocking log jams, etc. in note. If a habitat structure spans across several habitat units record it only once. Put the comment code in the unit that is most affected by the habitat structure. MIning Potential Artificial Barrier. Potential artificial or human created barrier to upstream or downstream migration of fish. Document height, take photos and notes. Potential Natural Barrier. Potential natural barrier to upstream or downstream migration of fish. Document height, take photos and notes. (Note: Barriers are relative to stream size and fish species encountering them. Consider these variables when using this comment code).

23 Comment Codes (continued) RF Road Ford. Road that crosses within the active channel of the stream (no bridge). SD Screened Diversion (pump or canal). Give some indication of size or capacity. SS Spring or Seep. Usually small amounts of flow (<5% of total flow) directly entering from hillslope. For large springs, estimate the contribution to flow. Springs do not have defined channels. TJ Tributary Junction with named and unnamed tributaries. Use the TJ class only for tributaries with clearly developed channels. Survey even if the trib is dry. Locate and record unit number on the topo map. Indicate which side of the stream the trib is located. Record a temperature and the estimated Active Channel Width. UD Unscreened Diversion (pump or canal). Give some indication of size or capacity. WL WildLife use of stream or riparian zone (note species) This code refers to anything except fish species. Record fish observations only in the note column. Identify species if possible. Mass Movement: Use a two-part code. The first letter identifies the type of mass movement failure. The second letter evaluates the apparent activity of the failure. (Example: AI = inactive debris avalanche.) Type: E L A Earthflow: general movement and encroachment of hill slope upon the channel. These can be identified by groups of unusually leaning trees on a hillslope Landslide: failure of locally adjacent hill slope. Usually steep, broad, often shaped like a half oval, with exposed soils. Avalanche: failure of small, high gradient, tributary. Often appear spoon shaped looking upslope. Water may flow in these intermittent or ephemeral channels that contribute alluvial soils and debris. Condition: A I S Active: contributing material now. Inactive: evidence of contribution of material during previous winter or high flows. Stabilized: vegetated scars, no evidence of recent activity. 11. Note. Additional information that describes the habitat unit, comment code, riparian vegetation, fish species present, measurements of steps, culverts, barriers, etc.