Sliding Door Instruction Manual Consumer Guarantee - Please make sure the purchaser/end user completes and returns the Guarantee card which is enclosed with this product. Failure to validate the Guarantee will mean only the 1 Year Statutory Guarantee will apply. Component Check List: Supplied No: Description Quantity 1 Wall Profiles 2 2 Sliding Door 1 3 Top & Bottom Rails 2 4 Fixed Panel 1 5 Magnet Profile 1 6 Door Magnet 1 7 Door Flipper Seal 1 8 Panel Seal 1 Fixing Kit: Component Check List IMPORTANT This is an important document as it holds the Consumer Guarantee which needs to be returned, please ensure it is retained by the end user. Please read these instructions carefully prior to attempting installation. Unpack and handle the product with care to avoid damage to the product finish. Check for hidden electrical cables and water pipes prior to commencing any drilling work. Do not plasterboard over the rim of the Tray. Ensure the walls where the Enclosure is to be fitted are vertical. (If the walls are not completely vertical there is 20mm of adjustment in each Wall Profile.) Note: It is recommended that the walls are tiled after the Tray is fitted and grouted before fitting the Enclosure. This will provide maximum adjustment and will aid sealing. No attempt should be made to rework toughened safety glass. Pictures used are for illustration purposes only, product designs may alter slightly as a result of continuing product development. Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according to our guidelines. It is important to note, that the glass must not be mounted or pinched in such a way that would cause a stress point to develop in the glass. In addition, it must not be subjected to any sharp impact or severe temperature fluctuation which may also cause a stress point to develop in the glass. Toughened glass is physically and thermally significantly stronger than standard glass. During our toughening process the stresses contained within any glass are balanced so if in the unlikely situation any of the above occurs and the glass breaks, the glass will shatter safely into small thumbnail sized blunt fragments. Please note that some natural misting may occur when you remove this product from its packaging, due to the addition of the glass protection pre-coating. If this does occur this can easily be removed with a soft, dry cloth. No: Description Quantity 9 Wall Plugs 6 10 35mm Screws (Wall Profiles) 6 11 Handle 1 12 12mm Screws 6 13 Screw Cover Caps 12 14 Top Caps 2 15 30mm Screws 8 16 Bearing Assemblies 2 17 Bottom Clip Assemblies 2 Equipment Check List: Not Supplied 4.5mm Drill Bit 8mm Masonry Drill Bit 3.2mm Drill Bit Mains or Battery Drill Spirit Level Pozi/Flathead Screw Driver Bathroom Sealant Gun Bathroom Sealant Tube Tape Measure Pencil Pliers Additional fixings if going into plasterboard Before Assembly and Installation of the Sliding Door * Check the product for defects. Installation queries on damaged parts can not be resolved once the installation has been completed. * The Tray must be completely sealed along tiled walls, fitted level (check with a Spirit Level) and should have no leaks. Notes: It is recommended that the Wall Profiles are fitted directly onto tiles or a similar sealed surface. If walls or tray or a combination of both are out of level you will not achieve full adjustment of maximum width. If you have any problems with your Shower Enclosure once installed, please refer back to this Instruction Manual to ensure you have completed every stage correctly. If you still experience any difficulties or have any queries please contact us on +44 (0) 1325 328033 for Technical Assistance or +44 (0) 1325 328034 for Sales. H2S Aug 12
Stage 1 - Check and Seal the Tray Check the tray is level on all sides. Check the tray has been completely sealed between the tiled wall and tray. Note: Ensure the tray is installed as per the manufacturers instructions. Stage 2- Drill the wall profiles and mark the drill hole locations. Drill 3; 4.5mm holes into both wall profiles through the lip see diagram. Locate both profiles 10-15mm from the front of the tray. (The lip of the wall profile should face in towards the enclosure). Using a pencil mark the locations for the drill holes remember the wall profiles will be fixed to the wall through the lip. Make sure the all profiles are completely level. 10-15 MM Profile Lip. Remember if fitting with side panel - locate the wall profiles as shown. Stage 3 - Drilling the Wall Drill the holes using 8mm masonry drill bit. Push the wall plugs into the drilled holes.
Stage 4 - Screw-fixing the 1st Wall Profile Apply a bead of silicone the width of the wall profile at the bottom where it will meet the tray and tiled wall. Screw fix the wall profile to the wall using the 35mm screws. Apply a bead of silicone to the inside of the wall profile at the bottom where it meets the tray top. Width of the Wall Profile Inside the Wall Profile (If fitting with a side panel, fix both wall profiles here.) Stage 5 - Assemble the Top & Bottom Rails to the Fixed Panel Before assembling the top and bottom rails to the fixed panel, ensure that both transit blocks are removed from the top and bottom of the fixed panel Take the seals out of the top and bottom rails and position them over the top and bottom of the fixed panels as shown. Please note: The top rail shown in the image is for illustration purposes only. Assemble the top and bottom rails to the fixed panels using the supplied 35mm screws. Fit the fixed panel seals onto the leading edge of the fixed panels; ensure the flipper is facing in towards the showering area.
Stage 6 - Assemble the Magnet Seal Profile to the Fixed Panel Assemble the magnet profile to the top and bottom rails that are attached to the fixed panel using the supplied 30mm screws. Stage 7 - Locate the 2nd Wall Profile Locate the 2nd wall profile into the aluminium profile of the assembled fixed panel Magnet Profile Stage 8 - Lift the assembled Fixed Panel onto the Tray & Fix the 2nd Wall Profile - If fitting with a side panel perform stage 2 only - then refer to your side panel instructions Prior to lifting the assembled fixed panel onto the tray, apply a bead of bathroom sealant the width of the wall profile, where the 2nd wall profile will meet the tray and tiled wall at the bottom. Lift the assembled fixed panel onto the tray and locate it onto the 1st wall profile. Adjust the 2nd wall profile so it locates against the wall and the holes in the profile lip line up with the drilled holes in the wall. Using a screwdriver screw fix the wall profile to the wall using the 35mm screws. Width of the Wall Profile Inside the Wall Profile
Stage 9 - Securing the Enclosure to the Wall Profiles Ensure the enclosure is completely level and centered between the wall profiles (see diagram). Drill holes through the wall profiles and into the profiles of the enclosure using a 3.2mm drill bit. The holes should be drilled 50mm from the top, 50mm from the bottom and in the centre. Stage 10 - Screw Fixing the Enclosure. Using the 12mm screws secure the enclosure to the wall profiles Fit the fixed panel seal onto the leading edge of the fixed panel. Fit the screw cover caps to conceal the 12mm screw heads.
Stage 11 - Assemble the Wheels and Bottom Door Clips to the Door Position the wheels through the glass (A1). Place the back plate on the inside of the glass and screw together (A2). Slide the cover cap up over the back plate (A3 and A4). Position the bottom door guides over the bottom of the door (B1). Secure the bottom door guide by using the screws supplied (B2). Slide the cover cap down over the bottom door guide (B3 & B4). Fit the door handles to the sliding doors. Fit the door seals to the sliding doors. Fit the door magnets to the handle side. Please note: Ensure the seals are fitted on the doors correctly. A1 A2 A3 A4 B1 B2 B3 B4 Spacers Fit the Plastic Spacer s between the Glass & Handle Door Magnet Sliding Door Handle Door Seal
Stage 12 - Fitting the Door Lift the door inside the frame, Position the wheels at the top of the door into the top rail. At the bottom of the door push down on the spring loaded door guides until they clip under the bottom rail When the door is closed, make sure the magnets of the door and frame locate onto each other along the full length. Make sure the doors clips are located under the bottom rail securly. If necessary the doors can be adjusted to achieve this, adjusting the doors can also help the running action - follow the adjustment instructions below. * Adjust the doors by rotating the adjustment screw on the top bearing. Stage 13 - Sealing the Enclosure and fit the top caps Seal both sides of the wall profiles vertically inside and outside where they meet the tiled walls. Fully seal the base of the enclosure to the tray top from the outside only. Please allow 24 hrs for the sealant to cure prior to using the enclosure. Fit the top caps to the profiles of the door (the caps have a snap-off function to allow a good fit). Important: Failure to follow the sealing procedures correctly may result in serious water damage and will not be covered under the terms of the guarantee.
Cleaning your product: Shower Enclosures are designed for luxury showering and with care and attention you can keep them looking new for longer. Simply clean your Shower Enclosure regularly using a soft cloth and warm soapy water and If you live in a hard water area, occasionally clean your Shower Enclosure using a 50/50 solution of white vinegar and water. The solution should be left on the product for approximately 5 mins and then rinsed off using warm water. This method of cleaning should remove lime scale residue. It is also a good idea to wipe all water droplets and residue from the glass surfaces of your Enclosure after use - a window "squeegee" is ideal for this task. This is particularly important in hard-water areas where lime scale build up is likely if water is left on the smooth glass surface for extended periods of time. The use of any other cleaning products is not recommended Proprietary cleaning products frequently change formula without notification and cannot be endorsed for this reason. A List of don ts: Don t use acidic based products. Don t use abrasive cleaners and/or cleaners containing bleach or solvents. Don t use scouring pads, powder or any sharp instruments.