B.T...H./E Humidity, Temperature & ew Point Transmitter with Replaceable Humi-chip Module H line and H line The H and H transmitters determine measurements by means of a highly accurate condensation resistant capacitive sensor integrated in a silicon microchip. This technology provides accurate process measurements, reliability and excellent long-term stability. Accurate ew Point calculation is obtained by the integrated humidity and temperature sensors. The sensor must not be used in presence of chemical contaminants or aggressive compounds. The Humi-chip module that incorporates the sensor can be easily replaced without the need for recalibration; Humi-chip environmental limits: -...+9 C; Stability: Long-term drift <. RH% per year; Two isolated analogue outputs: selectable for Relative Humidity (RH), Temperature (T), ew Point (P), Temperature and ew Point Temperature difference ( T); Alarm: Relay outptut programmable for UR, T, P, T; Real Time Clock (RTC): to trace events and correctly store data; Serial communications: RS8 Modbus RTU for digital retransmission and PC configuration; Enclosure rating: IP66. E Ascon Tecnologic srl via Indipendenza 6, 79 Vigevano (PV) Tel.: +9-8 69 87, Fax: +9-8 69 87 Web site: www.ascontecnologic.com E-mail: vendite@ascontecnologic.com
Not only Humidity Hardware and functions H and H transmitters can be either wall or duct mounted or remote sensor mounted. The painted aluminum housing with connectors or terminal connections is IP66 rated for industrial applications and field installation. The standard H model measures humidity and temperature on a digital display. Two analogue outputs and serial communications are optional. The standard H model calculates the dew point and the difference between the temperature and the ew Point temperature ( T). Options include alarms, event tracing and data logging. Busses, Interfaces and Gateways H and H transmitters have standard Modbus Protocol RS8 Serial Communications. The serial port enables the operator to connect supervisory software, via PC, to accurately monitor the measurements, alarm status and stored data. For fieldbus connection, Ascon offers two Gateway Manager modules: - X to connect Profibus or evicenet - Y to connect CANopen and Ethernet with ModbusTCP protocol and possible integrated Webserver. Fully software configurable. but also ew Point, T, Ser line LC to display: measured values, alarms and service messages Humi-chip pre-calibrated an Stainless steel wire mesh filter (quickly replaceable) Polycarbonate probe sheath (duct version) Artificial snow making Humiwith capac stable and Supervisor Air conditioning and ventilation in pharmaceutical industries RS8 ModBus to configure, set parameters and supervision ModBus TCP or CANopen Y Module
and Temperature, ial Communications and p Module d easily replaceable Wire mesh filter protection Enclosure rating: IP66. Connections: screw terminals with M6 conduit or pole M connectors Stainless steel sintered filter Teflon filter Event storing and ata logging The H model stores event details and ata Logging. Alarm event details including measured values, date, time and duration are stored using the internal Real Time Clock (RTC). Measured ata Logging values are stored on an operator determined cycle. The FIFO memory writes data to an EEPROM that cannot be modified by the operator. The Alarms The H model allows the operator to configure up to alarms which can be combined with any of the system measurements: Humidity, Temperature, P, T and Humi-chip break. Each alarm can be configured as minimum or maximum, absolute, deviation or band threshold, istantaneous or delayed, inhibit at activation (Blocking) or acknowledge (Latching). Alarms can be addressed to a relay output. Aligning Transmitters are factory calibrated and no further calibrations are required even after replacing the Humi-chip sensor. Humidity and/or Temperature measurements can be aligned by using measurements taken from a reference transmitter. The alignment is made on or points and minimizes measurement errors in real working conditions. The easy sensor calibration requires no accessories. chip Module itive sensor, accurate, moisture resistant Storerooms to ripen and preserve fruit and vegetables... Configuration X Module Storerooms for seasoning meat and cheese... PROFIBUS or evicenet or Modbus Includes process measurements alarms
Characteristics at C ambient temperature Note: ata highlighted in blue apply only to the H line. Relative Humidity (RH) Temperature (T) ew Point (P) T between Tand P Analogue outputs and Serial communications LC isplay Alarms Process auditing Power supply General characteristics Range..% RH Resolution bit Sampling time /s Temperature limits -... +9 C (figure ) Accuracy (figure ).8% between... 9% RH, non-linearity, hysteresis and repeatability included Typical long-term drift <. RH% per year -. +7. C (-... +8 F) -. +. C (-... +86 F) Available. +. C (... F) ranges. +. C (... F) Other ranges on request in range -... +8. C (-... +6. F) Resolution bit Accuracy (figure ) <. C between + C (... F) RT output - alternative (PT IEC 7) to ma or V output Tolerance: Class A (/ IN) - wire connection (figure ) -. +7. C (-... +8 F) Available ranges. +. C (... F) Other ranges on request in C or F Accuracy (figure ) < C between... % RH and -... +9 C (-... +6 F) Range.... C (... F) ma; Ω max. Output V; ma max. type V; ma max.... ma/... V can be set through the serial port (H only) Isolation Galvanic isolation of each output: Vdc/ min Retransmitted Typically analogue output transmits RH, analogue measurement output transmits T (H can transmit also P or T) Type Isolated wires RS8, with protocol Modbus RTU Slave Baud Rate Selectable up to 9, Baud Type lines of 6 characters Line height.6 mm Usage Configuration and display messages Humidity RH:....% RH Indication Temperature T: -... +. C (-... + F) (menu ew Point P: -... +. C (-... + F) (H only) selectable) T = T - P:.. C (... F) (H only) Number, combinable with each measure (RH, T, P, T) or Humi-chip break Type Min./max., delayed and/or stored Output type Relay SPST, max. A at Vdc or at Vac, directly activated by each alarm or with AN/OR logic FIFO buffer in non volatile memory (, records). Recording ata cannot be altered. method Record format: event type, RH, T, P, T and date/time. recording methods available Event logging When an alarm occurs, the system starts storing the event records at a rate different from the data logging rate ata logging The measured values are cyclically recorded. Recording timing:... 9 min 8... 7Vac or... Vdc Power consumption W max. Housing material Polycarbonate (RAL 78) Protection: IP66 Probe material Polycarbonate Safety Compliance to EN 6-, double isolation, pollution class, installation class II Electromagnetic compatibility Compliance to CE standards EN 8-, EN 8- Housing environmental -... +7 C (-... +8 F) without display temperature -... +6 C (-... + F) with display Electrical connections Standard: spring terminal strip, AWG8-6 wire Overall dimensions See page Working limits of Humi-chip module %RH 8 6 Normal conditions Limit conditions Figure - 6 8 C The measured reading accuracy is guaranteed through the Normal working conditions. A long-time period, at Limit conditions may generate a permanent drift up to +% RH. Humidity accuracy %UR ± ± ± ± ±. Temperature accuracy C ±. C ± ± ± ± ± ± - 6 8 Current/Voltage Output PT irect Output 6 8 ew Point calculation accuracy 6 8 Figure %RH Figure Figure Available functions H H Humidity + Temperature S S ew Point and T calculations S Analogue output O O Analogue output O O LC display O O Serial port (RS8 Modbus) + Alarms + Events + ata logging O S = Standard; O = option C %RH
Electrical wiring imensions Accessories and spares Version with internal removable spring terminal strip + - + - 6 7 8 9 + (~) - (~) C NO B b A - + 6 C nd Analogue output st Analogue output Power supply... Vdc (8... 7 Vac) Alarm output PT Temperature output RS8 Serial communications Mounting Wall mounting uct mounting / 8. Ø 6 Humi-Chip module Easy and fast replacement (no calibration needed) Model: AH-HUMICHIP Wire mesh stainless steel filter with threaded filter protection Porosity: µm Response time: s (...6%) Suitable for clean environments (no dust and moderate wind conditions) Model: AH-FRI Stainless steel sintered filter with threaded connection Porosity: µm Response time: s (...6%) Suitable for dusty environments; not moisture resistant Remote sensor mounting Model: AH-FSI 6 Ø 6/6/6 Teflon filter with threaded connection Porosity: µm Response time: s (...6%) Suitable for aggressive chemical environments, not suitable with high grade humidity Model: AH-FT Output Conduit M6 Wall mounting bracket for remote sensor Material: SS IN. x Ø screws holes max. CH 9 Model: AH-SMP = = 6 Mounting holes 6 8 6 Adjustable flange Ø self-locking for Ø probe Material: anodized aluminum No. holes Ø, distance between centers Ø7 mounting holes Ø. Model: AH-FLA
Ordering codes Model: Line Mounting - imensions Mounting Wall uct Remote H - A B - E F G - M I Probe dimensions Ø x L Ø x L Ø x L Ø x L6, cable m Ø x L6, cable m Ø x L6, cable m Stainless steel wire mesh Sintered stainless steel Teflon st Analogue Output - Humidity... ma /... % RH... V /... % RH... V /... % RH A B P C C R R S T E nd Analogue Output - Temperature... ma... V... V PT - Compliance with IEC7 Temperature Range ( F on request) (if F = or F = P) -... +7 C -... + C... C... C Internal LC isplay nd Analogue Output (option) st Analogue Output (option) F P G I Ascon Tecnologic srl via Indipendenza 6, 79 Vigevano (PV) Tel.: +9-8 69 87, Fax: +9-8 69 87 Web site: www.ascontecnologic.com E-mail: vendite@ascontecnologic.com Example: H-CR--M Model: H - A B - E F G - M I L Line Mounting - imensions Serial port (option) nd Analogue Output (option) st Analogue Output (option) Mounting Wall uct Remote Probe dimensions Ø x L Ø x L Ø x L Ø x L6, cable m Ø x L6, cable m Ø x L6, cable m Stainless steel wire mesh Sintered stainless steel Teflon st Analogue Output - Humidity [] - []... ma /... % RH... V /... % RH... V /... % RH A B P C C R R S T Example: H-RR--M Notes: [] On request, the st analogue output can be used for T, P o T. [] Other output ranges available (selectable using the serial communications). [] Temperature ranges suggested: P: -...+7 C or... C T:... C. E nd Analogue Output - Temperature []... ma Temperature... V T... V PT - IEC7 compliant... ma ew Point... V P... V T T - P... ma... V... V Temperature Range [] ( F on request) (if F = or F = P) -... +7 C -... + C... C... C Internal LC isplay Serial Communications + Special Functions RS8 Modbus + Alarms + Events + ata logging 6 F P 6 7 8 9 G I L