FlexBar HRT/FlexBar 3431 Accessories Clamp rings Welding parts Blind plugs Reductions Flanges Adaptors O-rings Wall bracket Description This data sheet holds accessories such as welding parts, clamp rings etc. for FlexBar HRT and FlexBar 3431. Besides the fi xed connections a range of replaceable, hygienic connections is available to mount on the FlexBar HRT/3431 with a fl ush diaphragm and G1/2A male nipple. FlexBar HRT is a loop powered, confi gurable pressure transmitter with 4...20 ma output and HART communication. Please refer to data sheet 3400-1. FlexBar 3431 is a confi gurable pressure transmitter designed according to the Profi bus PA profi le ver. 3.0 and is fully confi gurable via Simatic PDM software.communication. FlexBar 3431 is used in food, chemical and petrochemical industries to measure absolute or relative pressure. The integrated display is optional. Please refer to data sheet 3431-1. The FlexView display is optional. Please refer to data sheet 9401-1. Page 1
Accessories for FlexBar HRT 81 26-930 Flange, DN25, DIN 2527 for 816x xxxx x6xx 81 26-939 Blind plug, 3A/DN76, hygienic O-ring, EPDM included ø50.5 78 81 26-931 Flange, DN40, DIN 2527 for 816x xxxx x6xx 81 26-932 Flange, DN50, DIN 2527 for 816x xxxx x6xx 81 26-933 Flange, DN80, DIN 2527 for 816x xxxx x6xx 81 26-901 Clamp ring, ISO 2852, DN38/PN64 81 26-902 Clamp ring, ISO 2852, DN51/PN10 81 26-903 Clamp ring, ISO 2852, DN51/PN64 81 26-904 Clamp ring for fl ange, DIN 2527, DN38/PN64 (incl. spec. nut) 81 26-925 Welding part, M44 x 1.25 81 26-926 Tefl on seal for M44 male nipple, ø34.5 x ø40.5 x 0.8 81 26-927 Blind plug, M44 x 1.25 81 69-G901 Adaptor DIN 11851 for ø43 connection, DN40 (incl. union) 81 69-G902 Adaptor DIN 11851 for ø43 connection, DN50 (incl. union) ø64 81 26-905 Clamp ring for fl ange, DIN 2527, DN76/PN64 (incl. spec. nut) 81 26-916 Welding part, 3A/DN38, hygienic 81 26-919 Welding part, 3A/DN76, hygienic 81 26-938 Blind plug, 3A/DN38, hygienic O-ring, EPDM included 32 32 ø55 ø120 ø50.5 81 69-G903 Flange for ø43 connection mounting on 81 69-G911 15 81 69-G911 Welding part for ø43 mm connection 81 26-920 Reduction DS 228-1/ ISO 16288 for 816x xxxx x1xx Female nut G1/2 to male nipple G1/2A 4 holes ø11.5 ø65 ø84 ø65 78 81 26-921 Reduction DS 228-1/ ISO 16288 for 816x xxxx x1xx Female nut G1/2 to male nipple G3/8A [mm] 81 26-922 Reduction DS 228-1/ ISO 16288 for 816x xxxx x1xx Female nut G1/2 to male nipple G1/4A Page 2
Accessories for FlexBar HRT 81 26-923 M4 damping screw for the reductions (81 26-920, 81 26-921, 81 26-922) 81 26-924 Reduction for 816x xxxx x1xx Female nut G1/2 to female nut 1/2 NPT 1324-000 Condensing tube for steam measuring G1/2 Rotating Female nut (Left turn) 56 277 50 G1/2 male nipple 81 26-971 O-Rings (5 pcs.), NBR, DN38, FDA approved 81 26-972 O-Rings (5 pcs.), EPDM, DN38, FDA and 3A approved 81 26-973 O-Rings (5 pcs.), FPM, DN38, FDA and 3A approved 81 26-976 O-Rings (5 pcs.), NBR, DN76, FDA approved 81 26-977 O-Rings (5 pcs.), EPDM, DN76, FDA and 3A approved 81 26-978 O-Rings (5 pcs.), FPM, DN76, FDA and 3A approved 81 69-G981 O-Rings (5 pcs.), NBR, 81 69-G982 O-Rings (5 pcs.), EPDM, 81 69-G983 O-Rings (5 pcs.), FPM, 81 26-962 Wall bracket for FlexBar HRT/FlexBar 3431 M44/ø43, FDA approved M44/ø43, FDA and 3A approved M44/ø43, FDA and 3A approved 1324-002 Condensing tube for steam measuring 180 G1/2 male nipple 200 G1/2 rotating female nut (Left turn) 155 9701-0001 The FlexProgrammer 9701 is a dedicated tool to confi gure all Baumer confi gurable products. Type No. 9701-0001 complies: FlexProgrammer interface unit CD with the FlexProgram software and product drivers (DTM) USB cable Cable with 2 alligator clips 80 64 81 43-112 Cover ø86 for ø80 mm housing Stainless steel (AISI 304) with gasket of Nitril (NBR) 65 shore. 97 81 26-950 Factory assembly of accessories 81 26-960 Calibration certifi cate 81 26-998 Material certifi cate 3.1.b (EN 10204) - for wetted parts [mm] Page 3
CombiConnect Hygienic Replaceable s Description CombiConnect is a series of hygienic, replaceable connections in acid-proof stainless steel. The concept fi ts the G1/2A male nipple vers ions of FlexBar HRT/FlexBar 3431 pressure transmitter and the CombiTemp Pt100 sensor. The products comply with the strict demands from the food industry, represented by organisations such as 3A, FDA and EHEDG. It takes less than 2 minutes to mount the pressure transmitter or Pt100 sensor on the CombiConnect connection. CombiConnect is an entirely new concept offering high fl exibility and a low stock. The connection system is the ideal choice for customers measuring temperature and pressure in environments with several different connections. variants DS 722: DIN 11851: SMS 1145: BS 4825 (RJT): ISO 2853 (IDF) and ISO 2852 (Clamp): Varivent and Tri-Clover : Dansk Standard Deutsches Institut für Normung Sveriges Mekanförbunds Standardcentral British Standard International Standardisation Organisation Company Standards CombiConnect Technical Data Design Acid-proof stainless steel, (W1.4404/AISI 316L). Complies with the national standards DS 722, DIN 11851, SMS 1145, BS 4825, ISO 2852 and ISO 2853. Manufactured according to the relevant standards and guidelines from 3A, FDA, EHEDG and EN1672-2 Pressure range -1...25 bar Vibrations Lloyds Register, test 2 Disposal of product and packing According to national laws or by returning to Baumer Hygienic Installations Measures to be taken at hygienic mounting according to "European Hygienic Engineering Design Group" 1. Avoid blind pockets when connecting two pipe ends. 2. The gasket between male nipple and female nut must be levelled with the surface. 3. All parts must be centered in respect to each other. 4. Avoid blind pockets where media and cleaning materials can be accumulated. Page 4
Ordering Details - CombiConnect Type Complete connection, incl. special O-ring (NBR) and gasket. Incl. union ring if relevant. Welding part, incl. gasket and union ring if relevant. Tuchenhagen GEA, Varivent, DN40/DN50, Note {4} DS 722 DN40 Rotating female nut DS 722 DN40 Male nipple DS 722 DN50 Rotating female nut DS 722 DN50 Male nipple DIN 11851 DN25 Rotating female nut DIN 11851 DN25 Male nipple DIN 11851 DN40 Rotating female nut DIN 11851 DN40 Male nipple DIN 11851 DN50 Rotating female nut DIN 11851 DN50 Male nipple SMS 1145 DN38 Rotating female nut SMS 1145 DN38 Male nipple SMS 1145 DN51 Rotating female nut SMS 1145 DN51 Male nipple BS 4825 DN38 Rotating female nut BS 4825 DN38 Male nipple BS 4825 DN51 Rotating female nut BS 4825 DN51 Male nipple ISO 2853 DN38 Rotating female nut ISO 2853 DN38 Male nipple ISO 2853 DN51 Rotating female nut ISO 2853 DN51 Male nipple ISO 2852 DN38 Clamp ISO 2852 DN51 Clamp TriClover 3 Clamp 6 digit 8120 9xxx 1 2 01 12 13 14 15 20 21 22 23 24 25 32 33 34 35 42 43 44 45 52 53 54 55 6B 6C 7U CombiConnect Accessories 81 26-955 Mounting tool for O-ring DIN 11851, DN25 81 26-956 Mounting tool for O-ring DIN 11851, DN40/50 BS 4825, DN38/51 81 26-957 Mounting tool for O-ring ISO 2853 and clamp, DN38/51 SMS 1145, DN38/51 CombiConnect O-Rings Type no. 0-ring Range Notes 81 26-965 (5 pcs.) Nitrile (NBR) -30...100 C {1}, {2} 81 26-966 (5 pcs.) Etylene-propylene (EPDM) -30...150 C {1}, {3} 81 26-967 (5 pcs.) Fluorocarbon (FPM) -20...200 C {1}, {3} Notes {1} Complies with the demands from FDA {2} Change recommended after 50 CIP cleanings at 130 C {3} 3A approval {4} Tuchenhagen GEA welding part is not available. Page 5
CombiConnect Variants DS 722, Type no. 8120 911x BS 4825 (RJT), Type no. 8120 914x DN40: ø54 DN50: ø68 DN38: ø54 DN51: ø66.7 DIN 11851, DN40: ø58 DN50: ø72 Type no.8120 912x DN38: ø58.2 DN51: ø72.5 ISO 2853 (IDF), Type no. 8120 915x DN25: ø44 DN40: ø56 DN50: ø68.5 DN38: ø47 DN51: ø60.5 SMS 1145, DN25: ø52 DN40: ø65 DN50: ø78 Type no. 8120 913x DN38: ø50.5 DN51: ø64 Clamp, Type no. 8120 91xx AF 32 DN38: ø55 DN51: ø65 Clamp ISO 2852 DN38: ø50.5 Type no. 8120 916B Clamp ISO 2852 DN51: ø64 Type no. 8120 916C Tri-Clover 3" ø90.9 Type no. 8120 917U Note: All CombiConnect connections except the Clamp connection have two ø4.5 holes fi tting a standard AMF 44511 key (40 mm). DN38: ø60 DN51: ø70 GEA Tuchenhagen Varivent, Type no. 8120 9101 DN40/50: ø84 [mm] Page 6
CombiConnect - Mounting Instructions + = CombiConnect connection (+) Type number 816x xx1x x1xx Mounting tool for CombiConnect FlexBar HRT with Male nipple G1/2A for CombiConnect CombiConnect 1 1) Mount the O-ring in CombiConnect. 2) The sensor tube must be screwed into the CombiConnect until there is a 2... 5 mm gap between the O-ring and the bottom. 3) Press CombiConnect against the mounting tool to prevent the O-ring from sliding out. Tighten the sensor tube up at 20 Nm. 4) Tighten the safety-screw up at 2 Nm. 2 3 4 2 mm 50...100 N 2...5 mm 2 Nm 20 Nm Page 7
FlexBar HRT Accessories - Application Examples FlexBar HRT on the bracket for wall mounting FlexBar HRT with ø43 mm hygienic connection FlexBar HRT with M44 hygienic connection mounted with welding part Adaptor DIN 11851 for ø43 connection, DN40 (incl. nut) Adaptor DIN 11851 for ø43 connection, DN50 (incl. nut) UK/2007-03-21 This data sheet may only be reproduced in full. FlexBar HRT with DN38 clamp diaphragm seal Flange for ø43 connection mounting on a welding part Welding part, ø65 mm for ø43 mm connection Page 8