PHOENIX7 INSTALLATION INSTRUCTIONS AND REPAIR PARTS LIST FOR GENERAL USE WEATHER-TIGHT FIXTURES REGULAR ROUGH SERVICE, PORTABLE ROUGH SERVICE & MARINE/ROUGH SERVICE FIXTURES STURDILITE 7 ModelsWT-120/500, WT-120/56/500, WT-120/500P, WT-120/56/500P, WT-12/56/300P, WT-12/56/300P-14 MOUNTING (For Stationary Models Only) Fasten fixture with four 3/8 inch (9.5mm) bolts through holes provided in mounting base. Do not mount on unsupported cap or house roof. Attach near corner supports or use adequate subbase. Avoid mounting on light-weight cross members of booms or derricks which will vibrate or flex excessively. In addition to normal (base down) mounting, fixture may be attached in a pendant or cantilever manner. Lamping is accomplished through the hinged cover glass assembly. For fixtures with PAR 56 lamps, loosen two (2) screws on lamp support ring and rotate lamp retaining ring free from screws. Bring lamp partially out of fixture and detach socket. To install new lamp, just reverse the steps for lamp removal. When pushing socket onto lamp prongs of PAR 56 lamps, do not use excessive force. If socket goes on hard, try aligning contacts inside with slots in porcelain body by means of knife blade. LAMPING When re-lamping, it is recommended that the cover glass be cleaned to maintain fixture efficiency. (See CLEANING, Page 4.) WARNING TURN OFF FIXTURE AND ALLOW IT TO COOL BEFORE ATTEMPTING TO RE-LAMP. WT-120/500P & WT-120/56/500P PLUG INTO A GFCI PROTECTED RECEPTACLE ONLY. LAMP SUGGESTIONS for AWT@ Series Fixtures Fixture Model Volts Watts Description INC= Incandescent HL=Halogen Cycle Type of Lamp Type of Base Approx. Initial Lumens Beam Spread in Degrees Average Max. CP Central Cone Lamp -ANSI- PHOENIX Catalog 500W HL/Medium Flood HL/Wide Flood HL/Narrow Spot PAR 56 End Prong 8.000 20 x 42 34 x 66 15 x 32 49.000 18.000 90.000 Q500 PAR 56/MFL Q500 PAR 56/WFL Q500 PAR 56/NSP 4202400 4202500 4202600 300W INC/Medium Flood INC/Wide Flood INC/Narrow Spot PAR 56 End Prong 3.840 20 x 35 30 x 60 15 x 20 24.000 10.000 70.000 300 PAR 56/MFL 300 PAR 56/WFL 300 PAR 56/NSP 4200400 4200300 4200600 300W 500W INC/Medium Flood INC/Medium Flood R-40 Screw Base 3.650 6.500 115 115 2.200 4.700 300/3FL/MS 500R/3FL/MS 4200500 4201200 12/300 INC/Wide Flood PAR 56 Screw Term 6.000 60 x 40 12.700 25A PAR 56/WFL 4202200 N5485100F-1
WARNING When using outdoor use portable lamps, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and personal injury, including the following: a) Use only three-wire outdoor extension cords that have three-prong grounding plugs and grounding receptacles that accept the appliance's plug. b) Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for wet location portable lamp. Receptacles are available having built-in GFCI protection and are able to be used for this measure of safety. c) Use only with an extension cord for outdoor use, such as an extension cord of cord type SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, or SJTOW, SJTOW-A RISK OF ELECTRICAL SHOCK! Do not use with extension cord near water or where water may accumulate. Keep lamp at least 16 feet from pools and spas. Keep plugs and receptacles dry. READ ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS N 5485100F-2 81996 C PHOENIX PRODUCTS COMPANY, INC.
REPAIR PARTS LIST ITEM NO. DESCRIPTION PART NO. ITEM NO. DESCRIPTION PART NO. 1 Phoenix Mounting Base Assembly 1800100 13 Shell Mounting Hardware 1073100 2 Aluminum Base 7513600 14 Shell Mounting Hardware 1073200 3 Base Assembly MS 120/500 4 Shell Assembly 1817100 1072400 1072500 1072600 16 Harp Mounting Hardware 17 Harp Mounting Hardware 1053300 1073500 1072700 1072800 1072900 19 Cord Grip 4032800 5 Harp for AWT@ Series 2401801 4033100 6 7 Door for AWT@ Series 2662402 Cord Assembly 4114701 4114400 20 Watertight Plug Cap 4044300 21 Rubber Foot w/hardware 1073600 22 Lamp Support Kit 2022500 4114500 4115100 4117600 23 Lamp Retainer Kit P 1090180 1090210 8 Screw Lamp Socket 9 -End-Prong Lamp Socket 1090190 4502200 4500100 1090220 24 Handle Kit P 1090230 25 Lens Retainer Kit 1090240 10 Cover Glass 4602900 11 Gasket 5003800 12 Latch Fastener with Screws For AWT@ Series 1160120 N5485100F-3
REPAIR PARTS ILLUSTRATION N 5485100F-4 81996 C PHOENIX PRODUCTS COMPANY, INC.
WIRING: Models, These fixtures are prewired with a 4 foot (1.22m) three conductor electrical cord Apigtail@ for wiring to suitable power source. The green conductor is grounded to the fixture and must be connected to a positive ground. DO NOT CONNECT GREEN WIRE TO POWER SOURCE. Models and These fixtures are prewired with a stub three conductor electrical cord with attached watertight male twist-lock connector for connection to suitable power source with a mating watertight female twist-lock connector. Models and These fixtures are prewired with a 10 foot (3.05m) and a 14 foot (4.27m) (respectively) two conductor electrical cord for wiring to suitable power source. All wiring should be done by licensed electricians in accordance with State & Local codes plus NEC (National Electric Code Standards). Improper installation or use may result in serious injury. CLEANING: If the interior surface of the cover glass becomes dirty it is recommended that it be cleaned to maintain maximum light output. The glass may be cleaned with any non-abrasive conventional glass cleaner. To prevent the cover glass gasket from sticking at sealing surfaces it is recommended that a liquid silicone release agent be used. Best results are achieved when one application on the gasket is wiped dry (to clean the surface) and then a second application allowed to remain wet when cover glass assembly is replaced during relamping. One Year Products Warranty C (Limited Type) Phoenix Products Company warrants its product against defects in material and workmanship. Without charge, Phoenix Products Company will either repair or replace (Phoenix Products Company reserves the right to decide between repair or replacement) any properly installed Phoenix Products Company manufactured product which fails under normal operating conditions within one year from date of installation, provided it is returned to the factory (after authorization), transportation prepaid, and our inspection determines it to be defective under terms of this warranty. The warranty covers only equipment manufactured by Phoenix Products Company and does not extend to transportation, installation or replacement charges at buyer=s facility; nor does it apply to any other equipment of another manufacturer used in conjunction with Phoenix Products Company equipment. No other warranty, expressed or implied, exists beyond that included in this statement. PHOENIX PRODUCTS COMPANY, INC. 8711 West Port Avenue! Milwaukee, WI 53224 U.S.A. Phone: 414/973-3300 FAX: 414/973-3210 www.phoenixproducts.com N5485100F-5