BTRACK SAFE LIGHT USER MANUAL v.1.3 1 FEATURES 2200 mah Rechargeable Li-ion Battery Ultra Bright LED s Call Alert for Anti-Theft Feature Built in GPS / GPRS Built-in watchdog CPU to avoid system crash 2 SPECIFICATIONS Dimensions: 110mm x 40mm x 50mm GPS: U-BLOX G6010-ST, 50 canali Antenna: Internal Frequency: L1 1575.42 Mhz Position Accuracy: <5m Sensitivity: Tracking: -161dBm Cold starts: -156dBm Cold <27s start: Warm <5s start: Hot start: 1s A-GPS: AssistNow Online e AssistNow Offline services OMA SUPL compliant GPRS: MTK 6260D Quad band: 850/900/1800/1900 Mhz GPRS Class 12
Internal antennal 3 PACKAGE CONTENT Inside the package content there are: 1) BTrack Safe Light device 2) Star screwdriver 3) Seat tube clamp for mounting and seal gasket 4) USB cable 5) This user manual 3 2 1 4 4 SIM CARD PRE-INSTALLATION a) GSM Sim Only b) SIM card should have its GPRS function enabled. c) SMS request will function only if Caller ID function is enabled. d) If SIM card is locked via PIN, please unlock SIM. 5 SIM CARD INSTALLATION 1 1. Remove the 2 screws on the side cover (1) of the Safe Light device using the screwdriver supplied. 2. Insert the SIM card into the slot with the contact side facing down and with the angle to the left (follow the signs of 'sticker placed over the slot). 3. Dial the telephone number of the SIM card installed in the device and see if you hear the ringing tone. If so the SIM card is installed correctly.
6 DEVICE INSTALLATION Fasten the device to the seat tube through the fixing collar (3). Tighten the collar using the star screwdriver supplied (2). * NOTE: It is not recommended install the device on the quick release seat tube. 7 LIGHT FUNCTIONS Through the multifunction button (3) at the bottom of the device, you can: 1. Turn on fixed LED light: press button 1 time 2. Turn on flashing LED light: press the button 2 times 3. Turn off the LED light: press the button 3 times 8 INDICATOR LIGHTS / CHARGING DEVICE 3 2 1 The device is equipped with three LED lights (1) that light up to indicate: a) Red LED: battery charging is in progress (to fully charge the necessary time is about 8 hours) b) Green LED: the search for the GSM signal is in progress c) Blue LED: the search for the GPS signal is in progress During normal operation, the green LED and the blue LED are off. If they remain on indicate a problem of lack of GSM and / or GPS signal reception. For charging the device connect the power cable between the USB socket at the bottom of the device (2) and a USB power source (computer, power supply etc.). Check that the red LED turn on that indicates charging is on. Disconnect the USB cable when the red light goes off indicating that charging is complete. 9 TRACKING AND STATISTICS All owners of the BTrack devices can access to the web platform for tracking and statistics at the following address: http://btrack.sartoribikes.com
After performing the registration process you will receive an email with the data for the connection. At this point you can make the login and access to the dashboard page. In case of loss of the password you can retrieve it using the appropriate function. Using the Actions menu of the Devices panel you can add / remove or edit a device. During the first connection the Devices panel will be empty. You can add the purchased device using the IMEI (present at the side of the package). The Global Statistics panel displays information about the selected device. Through the Track Search panel will be possible to search by date and time the track, view it on Google maps, download the GPX file for further processing, display Track Statistics.
*NOTE: To view tracks must be enabled tracking function on the device 10 BTRACK APP The BTrack tracker is controlled remotely via SMS commands. For all smartphones ios and Android * * there is a free downloadable application from the app-store that allows easy and intuitive to query the device. *NOTE: For owners of other types of phones, see the chapter SMS COMMANDS NOTE: The screens are relative to the Android version. 10.1 Locate Allows you to display on Google map the location of the tracking 10.2 Statistics Open the internet browser of your smartphone at http://btrack.sartoribikes.com com for research and display of paths and statistics 10.3 Anthiteft Enable or disable the anti-theft mode (activated if the lock image turns green) 10.4 Tracking Enables or disables the tracking of routes (enabled if the satellite image turns green) 10.5 Settings Allows the registration of the following data in the BTrack device: a) APN b) Master Phone number c) BTrack Phone number d) Password
e) Sensitivity 10.6 Help Show the help guide with the description of the commands listed above 11 SMS COMMANDS Below are specified sms commands to establish a communication between the device and any mobile phone. To the owners of Android or IOS smartphones we recommend to downloading the dedicated application (BTRACK APP). 11.1 COMMAND LIST Function SMS Description Tracking Service Registration APN Registration Master phone number Registration *setip*95*170*88*81*5002* *apn*axxx*bxxx*cxxx* allow the data transfer from device to the server where Axxx is the name of APN, Bxxx the username and Cxxx the password *master*123456*+11xxxxxxxxxxxx* where master phone number is +1XXXXXXXXXXXX (+11 refers to the country code XXXXXXXXXXXX is the cell phone number). Please make sure country code is included and digit 0 is not needed before cell phone number Sensitivity settings Anti-theft on/off Tracking on/off Device location *sensitive*1-5* 1 most sensitive, 5 least sensitive. Default 1. *callalert* Call alert will call master number 2 times when motion is detected after 3 minutes non movement. *alertoff* End call alert function *routetrack*99* *routetrackoff* *locatemap* Turn on route track function End route track function Google Map link with current location
11.2 TRACKING SERVICE REGISTRATION This command must be done first (to allow the data transfer from device to the server) SMS to send: *setip*95*170*88*81*5002* SMS reply: Notice: IP is set to 95.170.88.81,5002 11.3 APN REGISTRATION SMS to send: *apn*axxx*bxxx*cxxx* (where Axxx is the name of APN, Bxxx the username and Cxxx the password) If there is no user name and password required, send as: SMS to send: *apn*axxx* Contact your service provider to know the name of APN. In response you will receive the following SMS : SMS reply: Notice: APN is set to xxx. User name: xxx. Password: xxx 11.4 MASTER PHONE NUMBER REGISTRATION The device will respond to instructions coming only from the phone number master. SMS to send: *master*123456*+11xxxxxxxxxxxx* (+11 refers to the country code XXXXXXXXXXXX is the cell phone number). Please make sure country code is included and digit 0 is not needed before cell phone number. SMS reply: Notice: Cell Phone # xxxxxxxxxx is set to master controller, the password is xxxxxx. (where xxxxxx is the default password of device). 11.5 PASSWORD CHANGE SMS to send: *password*xxxxxx* (where xxxxxx refers to new password) SMS reply: Notice: The password change is successful for +1XXXXXXXXXX. The new password is 654321. 11.6 TRACKING ON / OFF The device allows tracking. To enable tracking use the command: SMS to send: *routetrack*99* SMS reply: Notice: Routetrack function is set to always on. To disable tracking send the following command: SMS to send: *routetrackoff* SMS reply: Notice: System has ended routetrack function. 11.7 SENSITIVITY SETTINGS The device is equipped with a sensitive Vibration detection system. The unit comes from the factory preset to #1, on a scale of 1-5, with 1 being the most sensitive. If you notice you are getting excessive false
movement alerts, you can simply send the following SMS to the unit, and reset the variable: SMS to send: *sensitive*1-5* (where X = 1-5, 1 being the most sensitive, 5 the least) 1 = 3 seconds continued vibrating 5 = 15 seconds continued vibrating Default setting is 1 (per the explanation above) SMS reply: Notice: Vibration sensitivity is set to 1-5 11.8 DEVICE LOCATION You can track the location of the device using the following command SMS to send: *locatemap* SMS reply: You will receive back a text message with a google map link, click the link in order to view the location through cellphone browser. It is suitable for smart phone user only. * Note: Device will start positioning once it is powered on, location data will be saved and retained in memory every minute automatically. If GPS positioning fails, the nearest GSM cell tower data will be saved instead. 11.9 ANTHI-THEFT ON / OFF The device with anti-theft mode activated call master controller 2 times when motion is detected after 3 minutes of non-movement. To enable anti-theft use the command: SMS to send: *callalert* SMS reply: Notice: System has entered SMS alert function. To disable anti-theft send the following command:: SMS to send: *alertoff* SMS reply: Notice: System has ended alert function. 11.10 LOW BATTERY ALERT The device is equipped with an automatic "Low Battery" detection and alert when the battery drops to 20% of it s capacity. An alert SMS will be sent to master number, and tracking function will be turned off for power saving. As a reminder, the LED light will stop flashing and remains on as a constant during low battery period. SMS reply: Notice: Low battery alert Sartori Bikes Via Paolo Giovio 30-20144 Milano (MI) Tel/Fax. +39 024989276 Mail. info@sartoribikes.com - www.sartoribikes.com Unauthorized reproduction of all or part of this guide is prohibited