Th-550 Roof Guard / Silicone modified Water-Borne matt coating, based on Elastomeric Acrylic Polyurethane emulsion and modified by silicone resin for roofs. All types of exterior mineral facades (Masonry, concrete, plaster, brick, asbestos, cement, galvanized, steel and metals). Forms a waterproof film with high water vapor permeability. It has 400-600% elongation value depending on the surface temperature. It is formulated with micro spheres to lower the energy costs in both hot and cold climates by reducing heating and cooling demands. Saves up to 50% energy with original NASA technology. Excellent anti-condensation property. Bonds well to a range of surfaces. High filling and smoothing capacity. Consumption: Metal surface:0,850-1000 g/m² Cement surface:1,000-1250 g/m² ( for 2 coats) Th- 525 Exterior Coating / Silicone modified Water-Borne matt paint, based on Silicone emulsion for exterior facades. All types of exterior mineral facades: Masonry, concrete, plaster, tile, brick, asbestos, cement etc. Not suitable for previously painted surfaces with elastic / flexible coatings systems. Forms a waterproof film with high water vapour permeability. Saves up to 30% energy with original NASA technology. Application:Stir well before use. Dilute it by 10% (by weight) of clean, potable water for brush, roller applications Apply minimum two coats. Consumption: 0,350 Kg/m2 Th-530 Interior Coating / Silicone modified High quality water born acrylic co-polymer based top coat for interior mineral substrates. It is formulated with nano ceramic micro spheres to lower the energy costs in both hot and cold climates by reducing heating and cooling demands. It has also very powerful anti-condensation and sound deadening property. By means of these extra ordinary properties, this product is an excellent solution in high humidity living areas or the wall faced to north. High filling and smoothining capacity. Saves up to 30% energy with original NASA technology.. Application:Stir well before use. Dilute it by 10% (by weight) of clean, potable water for brush, roller applications Apply minimum 2 coats. Consumption: 0,300 Kg/m2 Th-523 Flex Exterior Coating / Silicone modified Water-Borne matt paint, based on Elastomeric Acrylic emulsion for exterior facades. It has 400 % elongation value depending on the surface temperature. It is formulated with micro spheres to lower the energy costs in both hot and cold climates by reducing heating and cooling demands. Saves up to 30% energy with original NASA technology Application:Stir well before use. Dilute it by 10% (by weight) of clean, potable water for brush, roller applications Apply minimum one coat. Consumption: 0,700-0,850 Kg/m2
Th-520 Textured Exterior Coating / Silicone modified Exterior Texture Coating is applied as a high-build coating with a very special texture appearance together with an extra ordinary thermal barrier property. Saves up to 30% energy with original NASA technology. It is designed to apply on unsmooth mineral surfaces. It is also applied as a top coat of board insulation systems like eps or xps. Exterior Texture Coating can reflect the significant amount of solar and ultraviolet radiations by means of a special type of Nasa inspired coated ceramic microspheres and reduces conductive type of heat transfer by a Nana technology based ingredient, which has the lowest conductive value over the world. A special silicone additive supports its weathering property, which also enhance the thermal insulation property of product. It has also very powerful sound deadening properties by means of the formulation ingredients. Thermal Paints & Coatings are innovative type of products to lower the energy costs in both hot and cold climates by reducing heating and cooling demands. Application:Stir well before use. Dilute it by 5% (by weight) of clean, potable water for brush, roller applications. Consumption: 0,850-0,950 Kg/m2 Energy Systems Laboratuary Ist.Yeditepe University Save 44% Manchester Salford University Thermal Laboratory United Nations Camp Report 40% effectiveness λ= 0,028 W/mK Istanbul Teknik University Thermal Conductivity Th- 515 Thermal Primer High quality water born acrylic co-polymer based primer for sealing, bonding and thermally wall boards. Bonds well to a range of surfaces. High filling and smoothining and strengtining capacity. Consumption: 0,100 Kg/m2 Th- 513 Galvanized & Metal Sealer Water based Acrylic-Polyurethane sealer. Excellent adhesion, high corrosion and blister resistance in a broad range of coating applications. It is an excellent barrier coat for galvanized surfaces before painted. Consumption: 0,100 Kg/m2 Th- 515 Nano Coat Primer Water born acrylic co-polymer based thermal coating Primer for sealing. Prefer for better thermal insulatin. Bonds well to a range of surfaces. High filling and smoothining and strengtining capacity. Consumption: 0,150 Kg/m2 TH-505 Thermal Floor Primer Water born acrylic co-polymer based primer is developed by Nasa Technology specially coated Ceramic Micro spheres for reducing energy loss through out flooring materials like parquet, carpet, pvc, and ceramic tiles. It seals and bonds the applied surfaces besides of the thermal insulating property. It can also be applied onto concrete, brick, building blocks, wallboards, and ceilings for thermal insulation. Significant amount of energy are lost through out from floors. It affects human health due to the direct contact of human foot and body with flooring materials. Therefore the thermal insulation of floorings is very important. It does lower the energy costs by up to 30 % in both hot and cold climates by reducing heating, cooling demands by applying onto the floors, carpet, and parquet backings. Consumption: 0,150 Kg/m2
Heat Insulating Metal Coatings Marine, Lng Tanks, Trains, Solvent Tanks, Metal Plastic - GRP Containers, Metal Roofs Thermal Heat Insulating Metal Coatings can reflect/ dissipating the significant amount of solar radiation (IR) by means of a special type NASA inspired coated ceramic microspheres and reduces the conductive type of heat transfer by a Nano technology based ingredient, which has the lowest conductive value over the world. This unique technology is also very efficient to prevent the exchange of heat transfer by gas molecules, which is known as Knudsen effect. Product No: TH-715 TH-720 TH-723 TH-810 TH-815 TH-825 Products Thermal Hr - 150 Water Based Thermal Hr - 600 Solvent Based Thermal Hr 600 Solvent Based Thermal Epoxy Metal Primer 2k Solvent Based Undercoat Thermal Epoxy Coating 2k Solvent Free Thermal Acrylic Polyurethane Top Coat 2k Solvent Based Description Water-Borne Heat Insulating Metal coating, based on Acrylic emulsion for exterior and ınterior Metal surfaces use up to 150 C degree. Extra UV resistant. Extra ordinary thermal barrier property. - Apply direct to metal. Use tanks and pipes lines on chemical plants, Marine ındustry. Sound and wibration reducer. Anti condensation and stops humidity. Resistance for acid and alkali. Colours: White - Aluminum Black Grey Oxide red Silicone based 1 component solvent born metal coating up to 600C. Curing ;1 hour at 200 C Colours: Aluminum black grey Silicone based 1 component water based metal and wood coating up to 600 C. Curing ; Room temperature Colours: Alumunium black grey TH-810 has a good impact and abrasion resistance properties. It has also very good adhesion to St3 prepared steel substrates coated with an anticorrosive epoxy coating and compatible with most aged coatings. * TH-810 is used to reduce the heat gain and/or loss of metal objects such as metal containers, cabinets, storage tanks, boilers, extruders, metal pipes etc. ** It can be used alone where the gloss or colour is not a major importance. If exposed to sunlight for long terms like 3-5 years, some gloss reduction occurs which does not significantly reduce the thermal insulation property of coating. If these are the important properties beside of thermal insulation, it is recommended to be over coated with DERİN TH-825 Acrylic PU Top coat. TH-815 is a solvent free epoxy resin based final layer gloss coating. * Excellent Thermal efficiency. It is highly resistant to a lot of chemicals, oil and sea water and corrosion. ** It is used in plants and industrial sites which require chemical resistance (against thinned acids, petrol natural and mineral oils), in concrete, floors, tanks, containers, pipes and trains which require precautions against corrosion. *** it is recommended to be over coated with TH-825 Acrylic PU Top coat. TH-825 Heat Insulating Acrylic PU Topcoat has a very strong impact, abrasion, ultraviolet and weather resistance properties beside of having the best heat insulating coating technology. It has also very good adhesion to St3 prepared steel substrates coated with. * TH-825 is used to reduce the heat gain and/or loss of metal objects such as metal containers, cabinets, storage tanks, same plastics and GRP surface, boilers, extruders, metal pipes, metal military objects and etc. The heat insulating performance difference of this coating can vary between 1 C to 10 C due to the weather or medium temperature faced. An other particular advantage of this coating system is its extremely high anti-condensation property which increase the coating durability performance by reducing water surface condensation which increase of solar power of sun by magnification. ** Best Thermal efficiency use TH 815 Epoxy Coating as a undercoat
Aplication Tables Product Decorative Coats Consumption No: Products Kg/m2 Thermal Textured or Flex TH- 510 Thermal Nano Coat 1 0,150 TH- 520 Thermal Textured or Flex 1-2 0,900 Thermal Exterior TH- 510 Thermal Nano Coat 1 0,150 TH- 525 Thermal Exterior - Slikon 2 0,350 Thermal İnterior TH- 515 Thermal Primer 1 0,100 TH- 530 Thermal Interior 2 0,300 Roof / Cement TH- 515 Thermal Nano Coat 1 0,150 TH- 550 Thermal Roof 2 0,900 Roof / Galvanized & Metal TH- 513 Galvanized & Metal Sealer 1 0,100 TH- 550 Thermal Roof 2 0,800 The Diffrence of Thermal Paints - Low labour cost, easy and fast application. - Do-it-yourself coating system. - Also has positive effect on sound insulation. - Fire retardant up to 1800 C. - Water based decorative paints lets the walls Breathe. - Increases the surface tension and reduces the moisture. - You can apply to all Silicone and Acrylic paints after appyling Thermal Primer. Aside being a good paint it also works as a insulator.
What is ROBYN S Thermal Coatings? Thermal is a revolutionary paint and coating group that cuts energy costs up to 30-50 % by reducing heating and cooling demands. This technology is found by NASA Technology Exchange Programme, independently tested and scientifically proven by Manchester / Salford Thermal Measurement Laboratories. Nasa actually developed this technology for their spaceships. NASA used big ceramic blocks on the spaceship surface to protect the spaceships between -250 F to 3000 F ( -80 C to + 1000 C) heat on the space. These ceramic blocks size is reduced to micro size for the paint systems. And we call them Nano Ceramic Micro Spheres. The most efficient way of reducing energy loss and saving your money is to have a good insulating paint and coating that will provide you an excellent thermal performance, which also protects your home against moisture by not preventing infiltration. Reflects about %95 solar lights Reflects about %80 of UV lights Global Warming Friendly; These coatings perform by reflection of heat and sun, this is the reason it is beneficial in hotter climates. Such as Middle East, Africa and other tropical climates. Because of this sun reflected activated paints, energy is saved 30% to 50%. In Summer ; During the cooling season, heat flows from outdoors to the house interior. To maintain climatical comfort, the heat lost in winter must be replaced by your heating system and the heat gained in summer must be removed by your air conditioner. Insulating ceilings, walls, roof and floors decreases this heat flow by providing an effective resistance to the flow of heat. Unfortunately the environment rarely provides the ideal that we seek in our homes, hence the advent of central heating systems and air conditioning systems. Until recently, apart from just accepting the loss of heat in the winter through our walls and roofs and in hot countries the flow of heat into the home there was little we could do, apart from spending large sums in trying to create a comfortable living environment. All the materials that are used in the construction of your home, bussines buildings absorb and transfer heat. 80% - 95% of this heat is transferred! In winter ; Heat flow moves directly from all heated living spaces to adjacent unheated attics, garages, and basements, or to the outdoors; or indirectly through interior ceilings, walls, and floors wherever there is a difference in temperature. These problems leaves us with energy problems. We have to use more energy to keep our living areas warmer. Local Distributor Derin Boya ve Denizcilik San.Tic.Ltd. Şti Tel: 009216 304 10 30 www.derinboya.com 7 Bedford St. London WC2E 9HA Tel: +44 (207) 8366443 / info@robynspaint.com