Anti Vibration Pads Alternate High/Low Ribbed Construction. Easy to Cut Pads can be cut to be slightly larger than the size of the leg or machine, using shears or knife. Easy Field Installation Multiple layers of Ribbed Mounting Pad can be used to increase deflection. EFRMP381818 EFRMP381212 EFRMP380808 EFRMP380606 EFRMP380404 EFRMP380303 3/8" x 18" x 18" 3/8" x 12" x 12" 3/8" x 8" x 8" 3/8" x 6" x 6" 3/8" x 4" x 4" 3/8" x 3" x 3" 12960 5760 2560 1440 640 360 5878 2612 1161 653 290 163 Ribbed Mounting Pads Cork sandwich Pads are laminated pads having 1/2" thick close grained cork securely bonded between two layers of 1/4" alternate low high ribbed Neoprene rubber pads. Offers highest level of sound attenuation and vibration isolation. No need for bolting. EFCSP781818 EFCSP781212 EFCSP780808 EFCSP780606 EFCSP780404 EFCSP780303 7/8" x 18" x 18" 7/8" x 12" x 12" 7/8" x 8" x 8" 7/8" x 6" x 6" 7/8" x 4" x 4" 7/8" x 3" x 3" 16200 7200 3200 1000 860 450 7348 3265 1451 454 390 204 Cork Sandwich Pads Metal Sandwich Pads are constructed of a steel plate bonded between Ribbed Anti Vibration Pads. Designed for very high load capacity. EFMSP011818 EFMSP011212 EFMSP010808 EFMSP340606 EFMSP340404 EFMSP340303 1" x 18" x 18" 1" x 12" x 12" 1" x 8" x 8" 3/4" x 6" x 6" 3/4" x 4" x 4" 3/4" x 3" x 3" 32400 14400 6400 3600 1600 900 14696 6531 2902 1632 725 408 Metal Sandwich Pads Due to policy of continual improvement, the specifications are subject to change without prior notice. Measurements are subject to 5% tolerance. To achieve good sound suppression do not over load fitting.
Rubber Pads Selection Procedure : Compute the total load in kg. to be supported by Easyflex Pads. This includes machine weight and work load it carries and also concrete or steel base or inertia block if used. Determine unit loading to suit type of machine and supporting ground structure 23 kg. per square inch is practical and effective loading and is recommended for most type of machines and equipment for isolation of sustained vibration. Divide the static weight by unit load to get total area of Easyflex Pad that is required. Arrange the total area of into adequate number of pads that are necessary to give stable support and to avoid base distortion. The area of each pad should be in proportion to the load carried by it so that the unit loading or stress on all pads will be approximately the same. The pads should be placed in such way that uniform deflection is obtained. Uniform load distribution prevents over loading and possible premature failure of some of the mountings, prevents sagging and enables the machine to maintain the normal horizontal position and make maximum isolation possible. Features : Scientifically designed resilient material that isolates shock and all the six modes of Vibration and reduce acoustic noise. They give more deflection than any other material i.e. cork, felt etc. They are cheaper than metal springs and have greater sound insulation ability. They are highly resistant to oil, cleaning compounds, dirt, water, strength, heat aging and fatigue. These are mostly used for machine tools, production equipments, heating and ventilation equipments, pumps, generators, compressors, air handling units, fans, under heavy concrete bases, electronics or sensitive laboratory apparatus, business machines, computers and data processor etc. Due to policy of continual improvement, the specifications are subject to change without prior notice. Measurements are subject to 5% tolerance.
Technical Specifications LOAD DEFLECTION CHART LOAD DEFLECTION CHART Part /Hardness EFRP101/50 EFRP102/70 EFRP103/50 EFRP104/70 LOADING CHART OF EASYFLEX PADS Thickness of Rubber Pad Max. unit 2 Load (kg/cm ) of 8 mm of 8 mm of 12 mm of 12 mm 3.5 7 14 21 (mm) 75 X 75 100 X 100 150 X 150 225 X 225 450 X 450 197 394 788 1181 350 700 1400 2100 787 1575 3150 4725 1772 3544 7088 10631 7087 14175 28350 42525 Other VI Pad sizes which are not our standard sizes (as mentioned above) would be specially manufactured as per client requirement. The Shore hardness A can be altered as per customer requirement to suit duty condition. Due to policy of continual improvement, the specifications are subject to change without prior notice. Measurements are subject to 5% tolerance.
Technical Specifications 0 0.02 0.04 0.06 DEFLECTION IN INCHES EFRP-101-A EFRP-102-B EFRP-103-C EFRP-104-D
Waffle Pad Standard size 18 x 18 x 3/4 (450 x 450 x19mm) consists of 81-2 (50mm) modules. The 2 (50mm) squares are separated by a thin web that is easily cut to provide evenly dimensioned pads such as 2 x 2 (50 x50mm), 2 x 4 (50 x 100mm), 4 x 4 (100 x100mm), 6 x 8 (150 x 200 mm), etc. EFWP is one of the thickest, most versatile and efficient pads in the market. s : Natural Rubber for maximum resilience and vibration isolation. Contains anti-oxidants and antiozonants to improve aging. Standard Neoprene for longer life and moderate oil resistance. Pads can be used to reduce noise, high frequency vibration and impact from typical machines as follows: Chillers HVAC Units Pumps Transformers Punch Presses Saws Drill Presses Compressors Vent Sets Motor Generators Diesel Generators Lathes Power Presses Load Rating Per Square Durometer Standard Load per 2 x 2 Square (lbs.) 80 120 180 240 360 15% Deflection Load per 50 x 50mm Square (kgs.) 35 53 80 105 158 CALCULATION EFWP Pads should be used in full squares. Select the minimum number of squares required and design pad to the most convenient square or rectangle. The use of additional squares results in more conservative loading. British Units Example Load is 980 lbs. 50 Duro capacity is 180 lbs. 980/180 = 5.44 squares (Use 6 square modules). Pad may be 2 modules x 3 modules (4 x 6 ) or 1 module x 6 modules (2 x 12 ) Metric Units Example Load is 5000 kgs. 50 Duro capacity is 80 kgs. 5000/80 = 62.5 squares (minimum). Pad may be 8 modules x 8 modules (400 x 400mm)or 7 modules x 10 modules (350 x 500mm) or 6 modules x 11 modules (300 x 550mm) etc. Due to policy of continual improvement, the specifications are subject to change without prior notice. Measurements are subject to 5% tolerance. To achieve good sound suppression do not over load fitting.