Tecnical seet pro-balcony pro-balcony G Finising profile for balconies and terraces Te pro-balcony G finising profile is a balcony profile for capping tiles. It protects te free areas in te edges from inclement weater and wear, and ensures a clean finis. Te system includes inside and outside corners. Features Resistant color UV and weater-resistant It protects free areas on te edges Possibility of installing gutters Substrates/uses Te pro-balcony G profile can be installed on balconies and terraces, bot on lamitec n type waterproofing seets and on sylastic type waterproofing mortar. Instructions for use Ceck tat te floor perimeter to be covered wit te pro-balcony profile is suitable for installing ceramics wit tin layer. In te case of unstable or crumbling substrates, carry out te necessary corrections. Apply te outdoor flooring waterproofing system. Extend it up to te outer limit of te floor perimeter. Apply a layer of type C2 as per EN 12004 cement-based adesive wit a notced trowel, on te substrate area tat will be covered by te pro-balcony profile s fixing flange. Apply a continuous seam of p-404 polyuretane putty on te substrate waterproofing, between te cement-based adesive layer and te outer perimeter of te flooring. Arrange te pro-balcony profile on te bonding material and elastic putty witin te adesive s open time. Press te profile flange on te adesive and ceck tat it is covered by te bonding material. In order to avoid stress between materials, leave a joint of at least 1 mm between eac profile. Apply a new layer of cement-based adesive tat is suitable for installing te cosen ceramic flooring. Lay te tile wit te tin-bed metod, wit adesive and a notced trowel. Arrange te ceramic tiles wit a placement joint of at least 5 mm. Level te profile wit te tile. Do not leave te profile above te tile level. Leave a placement joint between te ceramics and te profile of at least 2 mm. Seal wit a continuous seam of p-404 polyuretane putty. Never let te grouting material arden on te profile. Never use metallic tools or abrasive elements wic can scratc te profile surface. Cut te profile wit a and saw or wit a circular saw wit a suitable disc.
Cleaning and maintenance Tese profiles do not need cleaning and maintenance different from te tiles in wic tey are installed. Use neutral cleaning products. Do not use products containing ydrocloric or ydrofluoric acid. In any case, we recommend you perform a previous test before use. Do not use abrasive or metallic elements wic can scratc te profile surface. Tecnical data Profile lengt: Wall covering tickness: Cladding eigt (a): Profile tickness: Fixing flange: Material: Color: 90 outer corner pro-balcony G Closing profile: -Heigt -Outer measures 2.5 m 10.5 mm 55.1 mm 1.5 mm 88.7 mm aluminum medium gray 10.5 mm 240 x 240 mm pro-balcony G a
pro-balcony P Finising profile for balconies and terraces Te pro-balcony P finising profile is a balcony profile for capping tiles. It protects te free areas in te edges from inclement weater and wear, and ensures a clean finis. Te system includes outside corners. Features It includes drip edge. Resistant color. UV and weater-resistant. It protects free areas on te edges. Substrates/uses Te pro-balcony P profile can be installed on balconies and terraces, bot on lamitec n type waterproofing seets and on sylastic type waterproofing mortar. Instructions for use Ceck tat te floor perimeter to be covered wit te pro-balcony profile is suitable for installing ceramics wit tin layer. In te case of unstable or crumbling substrates, carry out te necessary corrections. Apply te outdoor flooring waterproofing system. Extend it up to te outer limit of te floor perimeter. Apply a layer of type C2 as per EN 12004 cement-based adesive wit a notced trowel, on te substrate area tat will be covered by te pro-balcony profile s fixing flange. Apply a continuous seam of p-404 polyuretane putty on te substrate waterproofing, between te cement-based adesive layer and te outer perimeter of te flooring. Arrange te pro-balcony profile on te bonding material and elastic putty witin te adesive s open time. Press te profile flange on te adesive and ceck tat it is covered by te bonding material. In order to avoid stress between materials, leave a joint of at least 1 mm between eac profile. Apply a new layer of cement-based adesive tat is suitable for installing te cosen ceramic flooring. Lay te tile wit te tin-bed metod, wit adesive and a notced trowel. Arrange te ceramic tiles wit a placement joint of at least 5 mm. Level te profile wit te tile. Do not leave te profile above te tile level. Leave a placement joint between te ceramics and te profile of at least 2 mm. Seal wit a continuous seam of p-404 polyuretane putty. Never let te grouting material arden on te profile. Never use metallic tools or abrasive elements wic can scratc te profile surface. Cut te profile wit a and saw or wit a circular saw wit a suitable disc.
Cleaning and maintenance Tese profiles do not need cleaning and maintenance different from te tiles in wic tey are installed. Use neutral cleaning products. Do not use products containing ydrocloric or ydrofluoric acid. In any case, we recommend you perform a previous test before use. Do not use abrasive or metallic elements wic can scratc te profile surface. Tecnical data Profile lengt: Wall covering tickness: Cladding eigt (a): Profile tickness: Fixing flange: Material: Color: 3 m 11 mm 20 mm 1.25 mm 60.5 mm aluminum medium gray pro-balcony P a
pro-balcony R Finising profile for balconies and terraces Te pro-balcony R finising profile is a balcony profile for capping tiles. It protects te free areas in te edges from inclement weater and wear, and ensures a clean finis. Te profile includes outside corners. Features It includes drip edge Resistant color UV and weater-resistant It protects free areas on te edges Substrates/uses Te pro-balcony R profile can be installed on balconies and terraces, bot on lamitec n type waterproofing seets and on sylastic type waterproofing mortar. Instructions for use Ceck tat te floor perimeter to be covered wit te pro-balcony profile is suitable for installing ceramics wit tin layer. In te case of unstable or crumbling substrates, carry out te necessary corrections. Apply te outdoor flooring waterproofing system. Extend it up to te outer limit of te floor perimeter. Apply a layer of type C2 as per EN 12004 cement-based adesive wit a notced trowel, on te substrate area tat will be covered by te pro-balcony profile s fixing flange. Apply a continuous seam of p-404 polyuretane putty on te substrate waterproofing, between te cement-based adesive layer and te outer perimeter of te flooring. Arrange te pro-balcony profile on te bonding material and elastic putty witin te adesive s open time. Press te profile flange on te adesive and ceck tat it is covered by te bonding material. In order to avoid stress between materials, leave a joint of at least 1 mm between eac profile. Apply a new layer of cement-based adesive tat is suitable for installing te cosen ceramic flooring. Lay te tile wit te tin-bed metod, wit adesive and a notced trowel. Arrange te ceramic tiles wit a placement joint of at least 5 mm. Level te profile wit te tile. Do not leave te profile above te tile level. Leave a placement joint between te ceramics and te profile of at least 2 mm. Seal wit a continuous seam of p-404 polyuretane putty. Never let te grouting material arden on te profile. Never use metallic tools or abrasive elements wic can scratc te profile surface. Cut te profile wit a and saw or wit a circular saw wit a suitable disc.
Cleaning and maintenance Tese profiles do not need cleaning and maintenance different from te tiles in wic tey are installed. Use neutral cleaning products. Do not use products containing ydrocloric or ydrofluoric acid. In any case, we recommend you perform a previous test before use. Do not use abrasive or metallic elements wic can scratc te profile surface. Tecnical data Profile lengt: Wall covering tickness: Cladding eigt (a): Profile tickness: Fixing flange: Material: Color: 2.5 m 12.25 mm 79 mm 2 mm 89 mm aluminum medium gray pro-balcony R a
Tecnical Seet Conditions Tis is not a finised product tecnical seet. It belongs to a product wic, togeter wit oters, is te base of a ceramic tile laying system wit wic professionals perform teir job. Instructions in tis tecnical seet ave been written based on our experience and tecnical expertise, but tey ave to be considered as general recommendations, wic togeter wit tose for te rest of te products in te system, elp te professionals in teir job. As it is not possible to know all te features and conditions of a building job, professionals must consider it and, if deemed appropriate, perform a previous test to confirm weter te product is suitable for te job. Specially recommended in applications wic imply mecanical stresses or cemical reactions not described in tis tecnical seet. Te tecnical seet cannot reflect all te applications and conditions entailed in te use of a material, so, in situations not described in tis seet, we recommend to perform a previous test and refer to our tecnical department. Tis seet as been updated in Marc, 2015.
pro-balcony G pro-balcony P pro-balcony R pro-balcony G pro-balcony P pro-balcony R
pro-balcony G Anodized aluminum KEA SAP (mm) B79241145 100159110 Profile 10.5 B79241148 100159111 Corner 10.5 pro-balcony P Anodized aluminum KEA SAP (mm) B79241146 100159112 Profile 11 B79241153 100159114 Outer vertical corner 11 B79241152 100159116 Inside vertical corner 11 B79241151 100159113 Outer orizontal corner 11 B79241147 100159115 Inside orizontal corner 11 Outer vertical corner Inside vertical corner pro-balcony R Outer orizontal corner Inside orizontal corner Anodized aluminum KEA SAP (mm) B79241150 100159117 Profile 12,5 B79241149 100159119 90º Corner 12.5 B79241154 100159118 135º Corner 12.5 butec building tecnology, S.A. Carretera Villarreal - Puebla de Arenoso (cv-20) km 2.5-12540 Villarreal - Castellón - Spain Apartado de correos: 297 - Telepone (+ 34) 964 53 62 00 - Fax (+ 34) 964 53 00 34 - butec@butec.es - ttp://www.butec.es