Washing, filling and capping 3 in 1 machine Summary: Feature: MIC14-12-5 washing filling capping three in one machine is composed with washing bottle, filling, capping three functions. It is used for non-carbonated drink filling, like mineral water, pure water This equipment has the following characteristics: 1. It is washing, filling, capping three in one, cover a small area. 2. The parts contact with finished drink adopt SUS304. Internal and external surface polishing treatment, easy to cleaning and it is hygiene. Seal ring are imported silicone or epdm, it does meet with food hygiene and filling requirements. 3. The design of washing machine can be washing the bottle by sterile water, to ensure the bottle cleaning. 4. micro-negative pressure type filling form, make the filling speed is faster and liquid level control stability. 5. High-energy magnetic capping machine, the torque can be adjustable and setting. To ensure the bottle good capping quality. Part 2 Filling and packaging machine 9 Washing filling capping 3 in 1 machine MIC 14-12-5 3000-4000bph 1 17500 10 Changeovers For 0.35L, 0.5L,1L&1.5L / / 11 Conveyor system SC-1 / 230/m According to the layout 12 Light checker DJ / 1 100 100 13 Dry machine / 4000bph 1 2,200 2,200
Main parts of this three in one machine 1. Platen and rack 2. Transmission device 3. Conveyor system 4. Air circuit control system 5. Protective door and safety device 6. Electric control system 7. Washing machine 8. Filling machine 9. Capping machine platen and rack 1. The platen is used for sustain transmission device, conveyor system and so on, to ensure the transmission and conveying the bottle smooth, accurate. 2. This part including platen, stainless still panel, ground jack, connection loop, support flange, stainless still door, and so on. Transmission device 1. This device including a main motor with frequency control of the motor speed, vortex transmission box, cardan shaft, gear, rotatory bearing to make the machine continuous running. Conveyor system 1. This system including star wheel of inlet field spider and outlet field spider, guard board, bottleneck plate, to ensure the bottle smooth conveying from inlet bottle-- washing bottle-- filling-- capping-- outlet bottle. Air circuit control system 1. It is composed with air preparation control component, solenoid valve and so on, to supply air for capping machine. Electrical control system This system including electrical control box, control cabinet, frequency converter, PLC, low-voltage electric element and so on. PLC controller to make the machine
even running, good performance and ease of operation, maintenance, etc. Washing machine 1. Rotary bottle washing machine including 18pcs clamp, and fixed nozzle. 2. It fixed water dish to collect the washing water. Filling machine 1. Filling machine are composed with filling tank, center pipe, main turntable, filling valve, star wheel, elevator device, cam device and so on. 2. The filling rotation system is supported by a large rotatory bearing, even running. The filling tank, center pipe are fixed in the turntable, and the turntable fixed the elevator device, this make the equipment easy to change the different bottle. 3. the filling valve will be open when there is bottle, the finished drink fill into bottle, meanwhile, discharge the air of inside bottle to return material tank from another channel, and the air of inside bottle will not contact with the finished drink in the filling tank to ensure the finished drink very clean, when the bottle full, there is a little finished drink will be collected into the return material tank, then by pump working to filling tank. 4. Special design of filling valve, the filling speed is faster and liquid level control stability. Capping machine Capping machine including capping heads, cap feeding channel, take cap device, no bottle no cap, lock the bottle neck to make positioning, high-energy permanent magnetic capping and capping torque can be accurately adjust to ensure the quality of sealing bottle. Ⅲ. Main disposition of the machine 1. Main motor: made in China 2. Reduction gears: made in China 3. Liquid level sensor: Yifan, from France 4. Spray blunt pump: Made in China 5. Touch screen: made in Taiwan 6. PLC controller: Mitsubishi 7. Frequency changer: Omron
8. Proximity switch, photo switch: Omron 9. contactor, breaker: Snyder 10. Mainshaft bearing: made in China 11. Seal ring: Sealtech Company, American 12. Capping bearing: made in China 13. Valve, tank, pipe parts that contact with the beverage adopt SUS 304. Ⅳ. Technical specs: 1. Capacity: 6000bph (500ml) 2. Washing heads: 18 3. Filling heads: 18 4. Capping heads: 6 5. Filling temperature: normal temperature 6. Filling method: Micro negative pressure type 7. Compressed air: 0.5~0.6Mpa Ⅴ. Power of whole machine 1. Main motor: 3KW 2. Motor of hopper: 0.18KW 3. Vortex pump 0.75KW 4. Spray blunt pump: 0.37KW 5. Water consumption: 1.5T/h(without the product water) 6. Dimansion: 2400 1900 2400mm 7. Net weight: 3500Kg
3. Lamp checker Enclosed of light test box adopts SUS304. It can be used for inspecting the impurity in finished product with good intensity of illumination.
Terms & Conditions: Payment: T/T 30% in advance, balance paid before shipment. Delivery: 30days after receiving the deposit. Packing: wooden case Validity: 1 year Sales After Service: Guaranty: One Year One set of consumable accessories will be provided with the machine. Before delivery, we will adjust the machine to fit for your product. Any question, you can mail/call us at any time. And our most experienced engineers is assigned to give consulting service, and always available for dispatching abroad. All spare parts are always available for delivery. Manual is in English. Installation/ Training: The installation can be provided by the MIC company. It must be after shipment and machine has arrived and factory must be ready equipped with all necessary requirements before booking installation with MIC company. Our engineers will come to the site for the complete and final installation. During the installation session, a one day training course will be provided to the customer to the customer for operation and maintenance procedure. The purchase at US$80/person/day plus all local transportation, accommodation, air tickets (round trip). Day charges include travel days.