The right colour, for every room.
A simple and complete guide. Simple and complete: these are the pillars of the Fassa Bortolo Colour System. For this reason we have developed this guide as an extra tool for paint professionals, who can find all the information they need in order to use the various systems correctly. For every System we provide the application cycles for the products that they are comprised of, the main characteristics and the technical specifications of each product. Key Paintable with ColorLife Tinting System European Technical Approval (ETA) The European Technical Approvals ETA 07/0280 and ETA 09/0282 which represent the positive technical evaluation of suitability for use of the products, based on the compliance and observance of all requirements set forth by the ETAG 004 Guideline. VOC Standard All of the products in the Fassa Bortolo Colour System comply with the parameters set forth by European Union standards, designed to limit the emissions of organic compounds; they comply particularly with Italian Legislative Decree No. 161 of 27/03/2006 (Implementation of Directive 2004/42/EC) which identifies the maximum Volatile Organic Compound content (VOCs) in paints and finish coat plasters in paste form. Table of contents Our view of the world is in the colour. p. 4 The simplest choice is the most effective. p. 6 We consider research an essential element. p. 8 Fassa Bortolo ColorLife Tinting System. p. 10 2
The Systems SILICONE RESIN p. 12 ACRYLIC DECORLIME p. 50 FS 412 Primer for silicone resin coating cycles p. 14 F 482I Filling undercoat with fine plaster appearance p. 14 PS 403 Highly breathable finish p. 15 SKIN 432 Protective siloxane finish p. 15 RSR 421 Silicone resin finish coat plaster with rustic effect p. 15 Application cycles p. 16 ACRYLIC-SILOXANE p. 20 FX 526 Universal pigmented primer undercoat p. 22 PX 505 Acrylic-siloxane filling finish p. 22 RX 561 Rustic acrylic-siloxane finish coat plaster p. 23 Application cycles p. 24 ACRYLIC p. 26 FA 249 Primer for acrylic systems p. 28 F 263A Filling undercoat with fine plaster appearance for exteriors and interiors p. 28 LV 207 Scrub resistant water-based paint with velvet finish p. 29 Gypsopaint Water-based paint for plasterboard p. 29 PL 215 Wash-resistant water-based paint p. 29 PT 213 Water-based paint with excellent coverage p. 30 PI 209 Universal water-based paint p. 30 PM 298 Professional breathable water-based paint p. 30 P 200 Water-based paint for walls p. 31 PB 260 HYGIENE Water-based paint with increased mould resistance p. 31 AM 270 Renovation solution for interiors p. 31 PG 288 PROTECT Smooth scrub resistant matt finish p. 32 C 285 BETON Protective finish for concrete p. 32 PA 202 ACTIVE Protective filling finish p. 32 MR 287 Water-based paint for exteriors with high filling properties p. 33 OM 306 Homogeniser for mineral finish coat plasters p. 33 RTA 549 Acrylic finish coat plaster for thermal insulated walls p. 34 RAR 256 Rustic acrylic finish coat plaster p. 34 Application cycles p. 36 SILICATE p. 44 FASSIL F 328 Silicate primer p. 46 FASSIL F 357S Filling undercoat with fine plaster appearance for exteriors and interiors p. 46 FASSIL P 313 Smooth silicate water-based paint p. 47 FASSIL R 336 Silicate finish coat plaster with rustic effect p. 47 Application cycles p. 48 PC 144 Decorative mineral lime-based finish p. 52 I 133 Mineral fine-grained lime-based plaster for decorative products p. 52 LS 122 Mineral-based smoothing with satin finish p. 52 RC 155 Decorative smoothing for interiors p. 53 SD 111 Decorative gloss mineral putty for interiors p. 53 ELASTOMER p. 54 FOND-ELAST 223 Elastomer evening undercoat with fine mortar appearance p. 56 PE 224 ELAST Elastomer filling finish p. 56 RI-ELAST 225 Elastomer finish coat plaster with rustic appearance p. 57 Application cycles p. 58 COMPLEMENTARY PRODUCTS p. 60 SOL-FIX 211 Solvent-based acrylic primer p. 62 IS 510 Siloxane water repellent p. 62 FAST 299 Filling paste p. 62 AM 270 Renovation solution for interiors p. 63 AC 241 Synthetic resin-based adhesion promoter p. 63 3
4 COLOUR System
Our view of the world is in the colour. Colours help us live better. They express our personality, they define our spaces. They can be warm, soft, pastel, bright, relaxing. If we use them in the spaces we live in, it is essential that they be natural. They let walls breathe, providing dry, healthy and comfortable living spaces. Fassa colours fully satisfy all of these requirements, because they are made from select materials. To let us, the buildings that house us and even the environment we live in, to live better. 5
6 COLOUR System
The simplest choice is the most effective. Whatever your need, the Fassa Bortolo Colour System is always the right choice. Because it includes technical solutions, and decorative solutions, for interiors and exteriors. And it is also the simplest choice, because everything is easier with Fassa Bortolo Colour System. Choose the right finishing product, immediately identify the intended use, know what binding agent it contains. It's all there in black and white, on every package. The colour of every package defines the intended use: undercoats, finish coat paints for interiors and exteriors finish coat plasters, decorative finishes, while binding systems are identified with letters of the alphabet. This saves you time, by choosing the right product for every need, for exteriors as well as interiors. With the same quality guaranteed by all Fassa Bortolo products. The letter identifies the type of binding agent The colour corresponds to the intended use undercoat Finish coat paint for interiors Finish coat paint for exteriors finish coat plaster decorative finish SILICONE RESIN ACRYLIC-SILOXANE ACRYLIC SILICATE DECORLIME ELASTOMER 7
Spresiano (TV): paint factory 8
We consider research an essential element. We do research, to produce quality. We find the most technologically innovative solutions, thanks to the constant commitment of our Research Centre, to broaden the horizons of our production. Investing in research is essential for any company that wants to constantly improve its results. That is why we created our own Research Centre, an advanced laboratory with a wide range of appliances and equipment. To analyse the material at a microscopic level and to evaluate the physico-chemical characteristics, in order to select formulations that guarantee the quality of products and predict, through specific tests, the behaviour in the most diverse environmental conditions. Our daily focus on research has also led us to achieve an important recognition, ISO 9001:2008 certification. Providing us with additional proof of the superior quality that we offer the building industry in this field as well. Not to mention the fully automated paint factory, where all of our energies are focused on constantly increasing the quality of our products and guaranteeing scheduled delivery times. To guarantee the best, always. X-Ray difractometer Spresiano (TV): Research Centre 9
10 COLOUR System
Fassa Bortolo ColorLife Tinting System The experience we have gained in the paint industry (fifteen years ago the first professional Fassa Bortolo tinting system was set up) has allowed us to build a new, evolved tinting system. Today, with the new ColorLife Tinting System, with the addition of 6 new organic colouring pastes for interiors, customers can choose the precise shade of colour, from among 1950 reproducible hues. ColorLife is based on NCS (Natural Color System ), the most widespread and commonly-used colour model in the world by material manufacturing companies, architects, designers, which codes colours according to how they are perceived by the human eye. A total of 1950 colour cards which, summed with 228 Fassa colour swatches, make the Colour System the most complete solution for every type of project. An assortment of 228 high quality hues. Modern, classic and pastel hues. 11
Very high protection Water-repellent Breathable IMPROVED mouldresistance For external thermal insulation systems For rising damp wall renovation systems 12
SILICONE RESIN The top of the line. Superior performance: high water-repellent properties, vapour permeability, excellent, long-lasting protection. The combination of these features makes Silicone Resin System products particularly suitable for decorating renovation base coat plasters on FASSATHERM external thermal insulation composite systems and wherever long-lasting protection is required. FS 412 Primer for silicone resin coating cycles p. 14 F 482I Filling undercoat with fine plaster appearance p. 14 PS 403 Highly breathable finish p. 15 SKIN 432 Protective siloxane finish p. 15 RSR 421 Silicone resin finish coat plaster with rustic effect p. 15 13
SILICONE RESIN UNDERCOAT FS 412 FS 412 Primer for silicone resin coating cycles FS 412 is a water-based primer used as an insulating agent, a primer or stabiliser of the wall before applying Silicone resin system finishing products, without altering the breathability of the wall. Specific for silicone resin cycles Water-repellent primer Specific weight: 1.00 kg/l approx. Dilution in weight: 1 part FS 412 with 1 part water Yield: approx. 7-9 m 2 /l Package: 16 litres Colour: transparent F 482I F 482I Filling undercoat with fine plaster appearance F 482I is a white filling undercoat, particularly suited to even out minor imperfections, providing a fine plaster appearance. The nature of the raw materials it contains makes the product suitable whenever there is a need for high breathability, low water absorption and high final yield. Evening structural base Fine grading: 0.5 mm Easy application Specific weight: 1.67 kg/l approx. Dilution, in weight, with water: 5-7% Yield: 4-6 m 2 /l approx. per coat Package: 14 litres Colour: white 14
UNDERCOAT FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER finish coat paints for exteriors PS 403 PS 403 Highly breathable finish PS 403 is a finish for exteriors that provides breathability, waterrepellency and excellent resistance to the outdoors, all at the same time. It also contains special molecules with improved resistance to mould and algae. It is suitable for application on any type of plaster, especially ones with dehumidifying properties, where it is necessary to offer high breathability and low water absorption at the same time. Very high breathability High water-repellent effect Improved resistance to mould and algae Specific weight: 1.58 kg/l approx. Dilution, in weight, with water: first coat up to 30%, second coat up to 20% for brush application Yield: 4-5 m 2 /l approx. (2 coats) Package: 14 litres Colours: choose from Fassa's 228 colour swatches SKIN 432 SKIN 432 Protective siloxane finish SKIN 432 is a finish for exteriors offering excellent water-repellency and high breathability, characteristics that provide a versatile application of the product, from acting as a finish on new or existing plaster, to treating facades that are insulated with the FASSATHERM External Thermal Insulation Composite System. Thanks to its special formula, facades that are treated with SKIN 432 also tend to stay cleaner than traditional finishes for exteriors. Maximum protection and cleanliness of the facade Excellent water-repellency Treatment for insulated surfaces Improved resistance to mould and algae Specific weight: 1.55 kg/l approx. Dilution, in weight, with water: first coat and any intermediate coats, 15%. Finish coat must be diluted to 5-10% in weight, based on the selected colour Yield: 4-5 m 2 /l approx. (2 coats) Package: 14 litres Colours: choose from Fassa's 228 colour swatches finish coat plaster RSR 421 For the proper use of products, consult the technical data sheets. RSR 421 Silicone resin finish coat plaster with rustic effect RSR 421 is a water-based finish coat plaster in paste form that provides breathability, water-repellency and excellent resistance to the outdoors, all at the same time. It also contains special molecules that improve its resistance to mould and algae. RSR 421 is suitable for application on any type of plaster, especially ones with dehumidifying properties, or on surfaces that are insulated with the FASSATHERM External Thermal Insulation Composite System. Compliant with standard EN 15824. Water-repellent and breathable Suitable for the FASSATHERM External Thermal Insulation Composite System and Renovation System Improved resistance to mould and algae Specific weight: 1.85 kg/l approx. Ready for use. Available in the following gradings: 0.6-1-1.5-2-3 mm. Consumption: 0.6 mm: approx. 2.5-3.2 kg/m 2; for two layers; 1 mm: approx. 2-2.5 kg/m 2; 1.5 mm: approx. 2.3-2.7 kg/m 2; 2 mm: approx. 2.6-3.4 kg/m 2; 3 mm: approx. 3.8-4.2 kg/m 2; Package: 25 kg Colours: choose from Fassa's 228 colour swatches 15
SILICONE RESIN Application cycles protective cycles for exteriors High protection cycles for exteriors distinguished by the products in the high breathability and water-repellency Silicone resin System. Once FS 412 water-based primer has been applied, it is possible to finish off with RSR 421 thicklayer coating or SKIN 432 finish. On slightly irregular walls we recommend applying F 482I filling undercoat before the SKIN 432 finish. neutral undercoat FS 412 Primer for silicone resin cycles for slightly uneven substrates finish coat plaster RSR 421 Silicone resin finish coat plaster with rustic effect finish coat paint for exteriors SKIN 432 Protective siloxane finish filling undercoat F 482I Smoothing coat in paste form with fine plaster appearance finish coat paint for exteriors SKIN 432 Protective siloxane finish 16 For the proper use of products, consult the technical data sheets.
UNDERCOAT FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER cycles for the renovation of damp walls The products in the Silicone Resin System provide high breathability and low water absorption at the same time, and are excellent for the finishing cycles in the renovation of damp walls. Once FS 412 water-based primer has been applied, it is possible to proceed with the highly breathable finish PS 403 or, for a rustic effect, RSR 421 finish coat plaster. neutral undercoat FS 412 Primer for silicone resin cycles finish coat paint for exteriors PS 403 Highly breathable finish Finish coat plaster RSR 421 Silicone resin finish coat plaster with rustic effect For the proper use of products, consult the technical data sheets. 17
SILICONE RESIN Application cycles cycle for the fassatherm external thermal insulation composite system To protect and complete the state of the art installation of the Fassatherm External Thermal Insulation Composite System, we recommend applying FS 412 neutral primer or FX 526 pigmented primer, followed by RSR 421 finish coat plaster, to obtain a film of paint with improved resistance to mould and algae. Additional protection is provided by applying SKIN 432 finish, which helps keep the surface even cleaner. neutral undercoat FS 412 Primer for silicone resin cycles pigmented undercoat FX 526 Pigmented anchoring undercoat Finish coat plaster RSR 421 Silicone resin finish coat plaster with rustic effect Additional protection finish coat paint for exteriors SKIN 432 Protective siloxane finish 18 The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated.
UNDERCOAT FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER 19
Wide range of colours HIGHLY PROFESSIONAL products Excellent performance Improved resistance to mould and algae 20
ACRYLIC-SILOXANE An innovative solution that combines the reliability of traditional acrylic formulas with the exclusive advantages of silicone resin. Ideal for those who have already experienced the efficiency of the Acrylic System first hand, Acrylic-Siloxane is an opportunity to obtain even higher performance and longerlasting results. FX 526 Universal pigmented primer undercoat p. 22 PX 505 Acrylic-siloxane filling finish p. 22 RX 561 Rustic acrylic-siloxane coating p. 23 21
ACRYLIC-SILOXANE UNDERCOAT FX 526 FX 526 Universal pigmented primer undercoat FX 526 is a pigmented primer used as an anchoring filling undercoat for thick layer finish coat plasters in water dispersion, whether synthetic, mineral, silicate or siloxane. While its hiding power creates a coloured and uniform surface, its fine aggregate content also improves the grip of the finish, in both FASSATHERM External Thermal Insulation Composite Systems and painted masonry walls. White or pigmented filling undercoat For thick layer coatings Pigmented primer for FASSATHERM External Thermal Insulation Composite Systems Specific weight: 1.61 kg/l approx. Dilution: with approx. 5% water Yield: 6-8 m 2 /l approx. Package: 14 litres Colours: choose from Fassa's 228 colour swatches finish coat paint for exteriors PX 505 PX 505 Acrylic-siloxane filling finish PX 505 is a decorative, white or coloured, water-based paint for exteriors, for use on new and old finish coat plasters based on lime-cement, concrete, etc.. PX 505 offers excellent protection from atmospheric agents thanks to its breathability and water-repellent properties. Excellent protection Good breathability Excellent water-repellency Improved resistance to mould and algae Specific weight: 1.57 kg/l approx. Dilution, in weight, with water: first coat up to 30%, second coat up to 20% Yield: 4-5 m 2 /l approx. (2 coats). Package: 5 and 14 litres Colours: choose from Fassa's 228 colour swatches 22
UNDERCOAT FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER Finish coat plaster RX 561 RX 561 Rustic acryl-siloxane coating RX 561 is a finish coat plaster in paste form composed of acrylic copolymers and special polysiloxanes and specific additives to make the product more resistant to mould and algae. The nature of the raw materials being used provides a finish with a rustic effect. RX 561 is used as a protective and decorative coat for exteriors on lime/cement base coat plasters and on walls that are insulated with FASSATHERM External Thermal Insulation Composite System. Also available in the winter version. Compliant with standard EN 15824. Excellent water-repellency Good breathability Excellent protection Improved resistance to mould and algae Specific weight: 1.85 kg/l approx. Dilution, in weight, with water: up to 2%, if necessary Available in the following gradings: 1-1.5-2 mm Consumption: 1 mm: approx. 2-2.5 kg/m 2; 1.5 mm: approx. 2.3-2.7 kg/m 2; 2 mm: approx. 2.6-3.4 kg/m 2; Package: 25 kg Colours: choose from Fassa's 228 colour swatches For the proper use of products, consult the technical data sheets. 23
ACRYLIC-SILOXANE Application cycles finishing cycles The cycle for exteriors using Acrylic-Siloxane products is comprised of FX 526 pigmented universal base followed by, depending on the case, PX 505 acrylic-siloxane finish or RX 561 coating. Both solutions provide the treated walls with improved resistance to mould and algae. neutral undercoat FX 526 Universal pigmented anchoring undercoat finish coat paint for exteriors PX 505 Acrylic-siloxane filling finish Finish coat plaster RX 561 Rustic acrylic-siloxane coating 24 The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated.
UNDERCOAT FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER 25
Versatile use Wide range of colours Improved resistance to mould and algae Solutions for interiors 26
ACRYLIC Maximum versatility of application on various types of surfaces, easy installation and resistance to atmospheric agents. Very broad selection, up to 1950 NCS shades for every need. FA 249 Primer for acrylic systems p. 28 F 263A Filling undercoat with fine plaster appearance for exteriors and interiors p. 28 LV 207 Scrub resistant water-based paint with velvet finish p. 29 Gypsopaint Water-based paint for plasterboard p. 29 PL 215 Wash-resistant water-based paint p. 29 PT 213 Water-based paint with excellent hiding power p. 30 PI 209 Universal water-based paint p. 30 PM 298 Professional breathable water-based paint p. 30 P 200 Water-based paint for walls p. 31 PB 260 HYGIENE Water-based paint with increased mould resistance p. 31 AM 270 Renovation solution for interiors p. 31 PG 288 PROTECT Smooth scrub resistant matt finish p. 32 C 285 BETON Protective finish for concrete p. 32 PA 202 ACTIVE Protective filling finish p. 32 MR 287 Water-based paint for exteriors with high filling properties p. 33 OM 306 Homogeniser for mineral wall finish coat plasters p. 33 RTA 549 Acrylic finish coat plaster for thermal insulated walls p. 34 RAR 256 Rustic acrylic finish coat plaster p. 34 27
ACRYLIC UNDERCOAT FA 249 FA 249 Primer for acrylic systems FS 249 is a water-based primer base used as an insulating agent, a primer or stabiliser for the base before applying any Acrylic System finishing products, on exteriors or interiors. Water-based product It evens out and reduces absorption High yield Specific weight: 1.00 kg/l approx. Dilution in weight: 1 part FA 249 with 6-8 parts water Yield: 25 m 2 /l approx. Package: Boxes of 12 pcs 1-5-16-litre containers Colour: transparent F 263A F 263A Filling undercoat with fine plaster appearance for exteriors and interiors F 263A is a white paste skim coat, particularly suited to even out minor imperfections, providing an appearance that is aesthetically similar to two-coat plaster. On smooth surfaces such as plasterboard, it provides a perfect base to roughen up the surface, for the application of finishing products. Structural base with hiding power Fine grading: 0.5 mm Easy application Specific weight: 1.70 kg/l approx. Dilution, in weight, with water: 5-7% Yield: 4-6 m 2 /l approx. per coat Package: 14 litres Colour: white 28 For the proper use of products, consult the technical data sheet.
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER FINISH COAT PAINTS FOR INTERIORS LV 207 LV 207 Scrub-resistant water-based paint with velvet finish LV 207 is a white or coloured water-based paint with finish effect for interiors, suitable for lime, lime-cement, gypsum plasters and plasterboard. It makes walls scrub-resistant and provides them with a velvety appearance. Smooth and matt effect Broad range of colours Exceptional yield Excellent scrub resistance Specific weight: approx. 1.41-1.50 kg/l Dilution, in weight, with water: 30-35% for brush or airless application, 25% for roller application Yield: approx. 7-8 m 2 /l (2 coats) Package: 4 and 14 litres Colours: choose from Fassa's 228 colour swatches + NCS colour selection gypsopaint GYPsopaint Water-based paint for plasterboard Gypsopaint is a finish for interiors with excellent hiding power and high flatness, characteristics that make it particularly suitable for applications on Gypsotech plasterboards. Its exceptional hiding power makes it perfect for other wall substrates as well. High hiding power Specific for plasterboard Excellent whiteness Wash-resistant Specific weight: 1.48 kg/l approx. Dilution: in weight, with water: 10-15% approx. Yield: 4-5 m 2 /l approx. (2 coats) Package: 5 and 14 litres Colour: NCS colour selection PL 215 PL 215 Wash-resistant water-based paint PL 215 is a wash-resistant finish for interiors with an acrylic binding agent, in an aqueous emulsion with good breathability. It contains additives that make it easy to apply, easy to clean, and provide it with good expansion. The high titanium dioxide content also provides excellent hiding power. Wash-resistant High yield Good expansion Specific weight: 1.64 kg/l approx. Dilution, in weight, with water: first coat up to 35%, second coat up to 25% Yield: approx. 5-6 m 2 /l (2 coats) Package: 5 and 14 litres Colours: choose from Fassa's 228 colour swatches + NCS colour selection For the proper use of products, consult the technical data sheets. 29
ACRYLIC PT 213 PT 213 Water-based paint with high hiding power PT 213 is a finish for interiors with excellent breathability. It contains additives that make it easy to apply and provide it with good expansion. Its formula provides excellent hiding power even with a single coat. It is suitable for any type of masonry work with fine mortar and provides the walls with a uniform and pleasant aesthetic appearance. High hiding power Breathable Exclusive finish Specific weight: 1.66 kg/l approx. Dilution, in weight, with water: first coat up to 35%, second coat up to 25% Yield: approx. 4.5-6 m 2 /l (2 coats) Package: 5 and 14 litres Colours: choose from Fassa's 228 colour swatches PI 209 PI 209 Universal water-based paint PI 209 is a finish for interiors, with excellent breathability, and its formula provides high hiding power. It is suitable for any type of masonry work with fine mortar and provides the walls with a uniform, solid and pleasant aesthetic appearance. Very high breathability High hiding power Excellent yield Specific weight: 1.70 kg/l approx. Dilution, in weight, with water: first coat up to 40%, second coat up to 30% Yield: 4-5 m 2 /l approx. (2 coats) Package: 5 and 14 litres Colours: choose from Fassa's 228 colour swatches PM 298 PM 298 Professional breathable water-based paint PM 298 is a finish for interiors with very high breathability. It is used as a matt water-based paint and is suitable for any type of masonry wall with fine mortar. It gives walls a uniform and velvety appearance. It is particularly suitable for professional applications on large surfaces. For large surfaces High hiding power Excellent whiteness Specific weight: 1.72 kg/l approx. Dilution, in weight, with water: first coat up to 40%, second coat up to 30% Yield: 4-5 m 2 /l approx. (2 coats) Package: 5 and 14 litres Colour: white 30
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER P 200 P 200 Water-based paint for walls P 200, water-based paint for interiors, contains additives that make it easy to apply, provide it with good expansion and excellent hiding power. It is particularly suitable for professional applications on large surfaces. High breathability High hiding power Easy application Specific weight: 1.72 kg/l approx. Dilution, in weight, with water: first coat up to 40%, second coat up to 30% Yield: 4-5 m 2 /l approx. Package: 5 and 14 litres Colour: white specific products with improved resistance to mould PB 260 HYGIENE PB 260 HYGIENE Water-based paint with increased mould resistance PB 260 Hygiene is a water-based paint added with special molecules that make the paint film even more mould-resistant. It also has the same characteristics of a matt finish for interiors: easy to apply, good expansion, high hiding power and breathability. Improved mould-resistance Excellent hiding power Matt breathable paint Specific weight: 1.65 kg/l approx. Dilution, in weight, with water: first coat up to 35%, second coat up to 25% Yield: approx. 4.5-6 m 2 /l (2 coats) Package: 5 and 14 litres Colours: choose from Fassa's 228 colour swatches AM 270 AM 270 Renovation solution for interiors AM 270 is an aqueous solution for interiors which contains special broad-spectrum molecules that help prevent the formation of mould on the applied paint. The solution is also suitable for use on surfaces that are already affected by these types of phenomena and need to be restored with a new cycle of paint treatment. For sanitising cycles for interiors Specific weight: 1.00 kg/l approx. Yield: approx. 8-12 m 2 /l depending on the absorption of the absorption Package: boxes of 12 1-litre bottles For the proper use of products, consult the technical data sheets. 31
ACRYLIC finish coat paints for exteriors PG 288 PROTECT PG 288 PROTECT Smooth scrub resistant matt finish PG 288 PROTECT is particularly suitable for decorating and protecting finish coat plasters, both new and coloured, and for providing superior performance in terms of water-repellency and the resistance to the formation of algae mould. PG 288 PROTECT is also used for its function as a CO 2 barrier on any building or exterior concrete surface. Long-lasting Smooth scrub resistant finish with silk effect Anti-carbonation barrier effect Improved resistance to mould and algae Specific weight: 1.31 kg/l approx. Dilution, in weight, with water: between 5 and 8% with brush/airless application; undiluted with roller application Yield: 5-7 m 2 /l approx. (2 coats) Package: 14 litres Colours: choose from Fassa's 228 colour swatches C 285 BETON C 285 BETON Protective finish for concrete C 285 BETON is used as a coloured protective and decorative finish on concrete and reinforced cement structures located on the exterior. It protects the treated building from carbonation, it provides a waterproofing action that reduces wear due to freeze-thaw cycles and gives it a uniform colour even if the casting is not homogeneous, all the while maintaining the appearance of facing cement. High anti-carbonation protection Excellent water-repellency Improved resistance to mould and algae Specific weight: 1.28 kg/l approx. Dilution, in weight, with water: first coat up to 15%, second coat up to 10% Yield: 5-6 m 2 /l approx. (2 coats) Package: 14 litres Colours: choose from Fassa's 228 colour swatches PA 202 ACTIVE PA 202 active Protective filling finish PA 202 ACTIVE provides excellent water-repellency and alkaliresistance; also, the presence of specific broad-spectrum additives makes the paint film even more resistant to mould and algae. For these reasons it is suitable for application on the exterior of any lime/cementbased finish coat plaster. Scrub resistant water-based paint with filling properties Excellent protection against atmospheric agents Improved resistance to mould and algae Specific weight: 1.55 kg/l approx. Dilution, in weight, with water: first coat up to 30%, second coat up to 20% for brush application Yield: 4-5 m 2 /l approx. (2 coats) Package: 14 litres Colours: choose from Fassa's 228 colour swatches 32
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER MR 287 MR 287 Water-based paint for exteriors with high filling properties MR 287 is a fine micro-coating with excellent water-repellency and alkali-resistance. It is suitable for application on any exterior or even interior lime/cement-based plaster, when it is necessary to provide a slightly rough, uniform finish. Fine scrub-resistant micro-coating Excellent hiding power Excellent protection Specific weight: 1.73 kg/l approx. Dilution, in weight, with water: up to 10% for brush application, undiluted or 5% at most for roller application Yield with brush application: 4-5 m 2 /l approx. (2 coats) Yield with roller application 3-4 m 2 /l approx. (2 coats) Package: 5-14 litres Colours: choose from Fassa's 228 colour swatches OM 306 OM 306 Homogeniser for mineral finish coat plasters OM 306 is used to protect coloured mineral finish coat plasters and make them homogeneous and uniform. It eliminates the possible formation of more or less intense spots that become more obvious in critical conditions. The nature of the raw materials being used allows the masonry to breathe perfectly. Provides a homogeneous and uniform effect Protective Breathable Specific weight: 1.30 kg/l approx. Dilution, in weight, with water: 15-20% max Yield: 3.7-5 m 2 /l approx. (2 coats) Package: 14 litres Colours: choose from the Folder Mineral Coatings For the proper use of products, consult the technical data sheets. 33
ACRYLIC finish coat plasters RTA 549 RTA 549 Acrylic finish coat plaster for thermal insulated walls RTA 549 is a finish coat plaster in paste form that is used mainly as a special protective and decorative coating for exteriors and with FASSATHERM External Thermal Insulation Composite Systems; its special formula creates a film with good resistance against the proliferation of mould and algae. Compliant with standard EN 15824. Excellent exterior protection Improved resistance to mould and algae Rustic effect Specific weight: 1.85 kg/l approx. Dilution, in weight, with water: up to 2%, if necessary Available in the following gradings: 1-1.5-2-3 mm. Consumption: 1 mm: approx. 2-2.5 kg/m 2; 1.5 mm: approx. 2.3-2.7 kg/m 2; 2 mm: approx. 2.6-3.4 kg/m 2; 3 mm: approx. 3.8-4.2 kg/m 2; Package: 25 kg Colours: choose from Fassa's 228 colour swatches RAR 256 RAR 256 Rustic acrylic finish coat plaster RAR 256 is a finish coat plaster in paste form for exteriors composed of special high water-repellent acrylic binding agents. The nature of the raw materials being used provides good breathability of the masonry work and a rustic-effect finish. Compliant with standard EN 15824. Excellent exterior protection High water-repellency Rustic effect Specific weight: 1.85 kg/l approx. Ready for use. Available in the following gradings: 0.6-1-1.5-2-3 mm. Consumption: 0.6 mm: approx. 2.5-3.2 kg/m 2; for two layers; 1 mm: approx. 2-2.5 kg/m 2; 1.5 mm: approx. 2.3-2.7 kg/m 2; 2 mm: approx. 2.6-3.4 kg/m 2; 3 mm: approx. 3.8-4.2 kg/m 2; Package: 25 kg Colours: choose from Fassa's 228 colour swatches 34
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER For the proper use of products, consult the technical data sheets. 35
ACRYLIC Application cycles cycle for the fassatherm external insulation composite system Finishing cycle for the Fassatherm External Thermal Insulation Composite System, involving the application of FA 249 undercoat followed by RTA 549 finish coat plaster. FA 249 primer can be replaced by FX 526 pigmented universal anchoring undercoat which, thanks to its excellent hiding power, creates a coloured and homogeneous surface for the subsequent application of the coloured finish coat plaster. neutral undercoat FA 249 Primer for acrylic systems pigmented undercoat FX 526 Universal pigmented anchoring undercoat Finish coat plaster RTA 549 Acrylic finish coat plaster for thermal insulated walls 36 The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated.
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER finishing cycle for exteriors Three finishing cycles for exteriors. The application of FA 249 undercoat is the first step towards the subsequent application of the finish coat paint, which can be either PA 202 ACTIVE, Protective filling finish, PG 288 PROTECT, scrub-resistant matt finish, or MR 287 with high filling properties. When using colours with poor hiding power it is advisable to apply FX 526 undercoat beforehand; otherwise use F 263A smoothing plaster for slightly uneven substrates. neutral undercoat FA 249 Primer for acrylic systems for colours with poor hiding power standard cycle for slightly uneven substrates pigmented undercoat FX 526 Universal pigmented anchoring undercoat filling undercoat F 263A Smoothing coat with fine plaster appearance for exteriors and interiors PA 202 active Protective filling finish finish coat paints for exteriors PG 288 PROTECT Smooth scrub resistant matt finish MR 287 Water-based paint with high filling properties for exteriors The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated. 37
ACRYLIC Application cycles finishing cycle for concrete For concrete finishes, depending on the choice of colour, it is possible to apply C 285 BETON, which offers a selection of grey colours, or PG 288 PROTECT which offers a vast selection of colours. For the base you will need to consider the use of SOL-FIX 211 solvent-based primer as an alternative to FA 249 water-based primer. neutral undercoat FA 249 Primer for acrylic systems OR SOLVENT-BASED UNDERCOAT SOL-FIX 211 Solvent-based acrylic primer SELECTION OF GREY COLOURS finish coat paints for exteriors VAST SELECTION OF COLOURS C 285 BETON Protective finish for concrete PG 288 PROTECT Smooth scrub resistant matt finish 38 The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated.
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER breathable cycle for interiors To finish indoor surfaces, depending on the case, it is possible to apply PT 213, PI 209 or PM 298, having previously applied FA 249 transparent primer; with slightly uneven substrates, however, apply F 263A filling undercoat, which is particularly suited to even out minor imperfections. neutral undercoat FA 249 Primer for acrylic systems for slightly uneven substrates filling undercoat F 263A Smoothing coat with fine plaster appearance for exteriors and interiors finish coat paints for interiors PT 213 Water-based paint with high hiding power PI 209 Universal water-based paint PM 298 Professional breathable water-based paint The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated. 39
ACRYLIC Application cycles wash resistant cycle for interiors When an indoor surface needs to be wash resistant, it is possible to choose LV 207 or PL 215. LV 207 in particular provides the walls with a smooth and matt effect. Both finishes boast a vast selection of NCS colours. neutral undercoat FA 249 Primer for acrylic systems for slightly uneven substrates filling undercoat F 263A Smoothing coat with fine plaster appearance for exteriors and interiors LV 207 Scrub resistant water-based paint with velvet finish finish coat paints for interiors PL 215 Wash resistant water-based paint 40 The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated.
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER SANITISING cycle for interiors To sanitise interiors, once the surfaces have been suitably prepared with a specific treatment, it is essential to restore the surfaces with AM 270 which helps prevent the formation of mould on the applied paint. After the FA 249 primer, it is possible to apply PB 260 HYGIENE finish, which is even more resistant to the formation of mould. substrate preparation phase wall renovation phase complementary AM 270 Renovation solution for interiors neutral undercoat FA 249 Primer for acrylic systems finish coat paint for interiors PB 260 HYGIENE Water-based paint with increased mould resistance The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated. 41
ACRYLIC Application cycles cycle on plasterboard Gypsopaint and LV 207 are two finishes for interiors with high hiding power, a feature that makes them an excellent choice for applications on plasterboard surfaces. FA 249 primer must be applied preventively, followed by F 263A filling undercoat, on the smooth surface of plasterboard. This solution is required to roughen up the surface and provide a final appearance similar to fine mortar. neutral undercoat FA 249 Primer for acrylic systems for a fine mortar finish filling undercoat F 263A Smoothing coat with fine plaster appearance for exteriors and interiors LV 207 Scrub resistant waterbased paint with velvet finish finish coat paints for interiors GYPsopaint Water-based paint for plasterboard 42 The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated.
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER 43
MATT appearance MINERAL products Breathable products For HISTORIC AND ARTISTIC BUILDINGS AND HISTORIC CENTRES 44
SILICATE Mineral finishes particularly suited for the decoration of historic centres, to achieve exclusive effects. Silicate-based products leave the vapour permeability properties of the substrate unchanged. FASSIL F 328 Silicate primer p. 46 FASSIL F 357S Filling undercoat with fine plaster appearance for exteriors and interiors p. 46 FASSIL P 313 Smooth silicate water-based paint p. 47 FASSIL R 336 Silicate finish coat plaster with rustic effect p. 47 45
SILICATE UNDERCOATS fassil f 328 FASSIL F 328 Silicate primer FASSIL F 328 is a water potassium silicate-based primer base used as an insulating agent, a primer or stabiliser for the mineral surface before applying any Silicate System finishing products, on exteriors or interiors. Mineral primer Very high breathability Specific weight: 1.00 kg/l approx. Dilution in weight: 1 part FASSIL F 328 with 1 part water Yield: approx. 7-9 m 2 /l Package: 16 litres Colour: transparent fassil f 357s fassil f 357s Filling undercoat with fine plaster appearance for exteriors and interiors FASSIL F 357S is a potassium-silicate-based filling undercoat in paste form, particularly suited to even out minor imperfections, providing an appearance that is aesthetically similar to fine mortar. It also creates an adhesive bridge between surfaces treated with organic-based paints and the subsequent silicate-based finish, keeping the essential capillary network open so that water vapour can pass through. Mineral connection undercoat Filling and uniforming Fine grading: 0.5 mm Specific weight: 1.74 kg/l approx. Dilution, in weight, with water: 5-7% approx. Yield: 3.3-4.2 m 2 /l approx. Package: 14 litres Colour: white 46
UNDERCOAT FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER finish coat paint for exteriors FASSIL P 313 Fassil p 313 Smooth silicate water-based paint FASSIL P 313 is a potassium silicate water-based paint with very high breathability. It has a mineral aspect and complies with standard DIN 18363. The nature of the raw materials being used maintains the breathability of the masonry. Potassium silicate finish Smooth effect with hiding power High breathability Specific weight: 1.47 kg/l approx. Dilution, in weight, with water: first coat up to 30%, second coat up to 20% for brush application; Yield: 3.5-4.5 m 2 /l approx. (2 coats) Package: 5-14 litres Colours: choose from Fassa's 228 colour swatches finish coat plaster fassil r 336 Fassil r 336 Silicate finish coat plaster with rustic effect FASSIL R 336 is a stabilised potassium-silicate paste finish coat plaster for exteriors and interiors, with very high breathability, compliant with DIN 18363. FASSIL R 336 is therefore particularly suited for cases requiring very high breathability, such as renovation cycles, and on historic buildings. Compliant with standard EN 15824. High breathability Mineral appearance Ideal for historic buildings Specific weight: 1.85 kg/l approx. Ready for use. Available in the following gradings: 0.6-1-1.5-2-3 mm. Consumption: 0.6 mm: approx. 2.5-3.2 kg/m 2; for two layers; 1 mm: approx. 2-2.9 kg/m 2; 1.5 mm: approx. 2.3-2.9 kg/m 2; 2 mm: approx. 3.0-3.7 kg/m 2; 3 mm: approx. 3.8-4.2 kg/m 2; Package: 25 kg Colours: choose from Fassa's 228 colour swatches For the proper use of products, consult the technical data sheets. 47
SILICATE Application cycles cycles for exteriors Cycles for exteriors, distinguished by products from the Silicate System with very high breathability. Once FASSIL F 328 water-based primer has been applied, it is possible to finish off with FASSIL R 336 finish coat plaster or FASSIL P 313 finish coat paint. On slightly uneven substrates we recommend applying FASSIL F 357S filling undercoat before the FASSIL P 313 finish coat paint. undercoat FASSIL F 328 Silicate primer for slightly uneven substrates Finish coat plaster Fassil r 336 Rustic silicate coating finish coat paint for exteriors Fassil p 313 Smooth silicate water-based paint filling undercoat fassil f 357s Smoothing coat with fine plaster appearance for exteriors and interiors finish coat paint for exteriors Fassil p 313 Smooth silicate water-based paint 48 The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated.
UNDERCOAT FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER 49
Decorative MINERAL Exclusive effects NATURAL LIME MAXIMUM BREATHABILITY 50
DECORLIME Exclusive mineral products with special aesthetic effect and high breathability made with pure lime putty, ideal for the restoration of old buildings and to enhance the appearance of new buildings. Its natural composition provides excellent qualitative properties, reproposing antiqued finishes with modern products that are easy to apply. PC 144 Decorative mineral lime-based finish p. 52 I 133 Mineral fine-grained lime-based plaster for decorative products p. 52 LS 122 Mineral-based smoothing with satin finish p. 52 RC 155 Decorative smoothing for interiors p. 53 SD 111 Decorative gloss mineral lime putty for interiors p. 53 51
DECORLIME decorlime PC 144 PC 144 Decorative mineral lime-based finish PC 144 is a lime-putty-based mineral finish, with excellent brightness, good expansion, high hiding power and low tendency to crumble. It can be used to overpaint and decorate the exterior walls of historic buildings coated with lime-based finish plasters, providing them with antiqued effects and breathability. Lime-based mineral paint Very high breathability Matt mineral effect Natural sanitiser Specific weight: 1.31 kg/l approx. Grading: < 0.1 mm Yield: 3.5-4 m 2 /l approx. (2 coats) Package: 5-14 litres Colours: choose from Fassa's 228 colour swatches I 133 I 133 Mineral fine-grained lime-based plaster for decorative products I 133 is a fine-grained decorative plaster used both for finishing and for preparing the surface; based on lime putty, with high breathability and good surface filling properties. Decorative fine-grained plaster Lime-based mineral content Very high breathability Fine-grained plaster effect Specific weight: 1.60 kg/l approx. Grading: < 0.6 mm Yield: approx. 0.33-0.40 m 2 /kg (2 coats) Package: 25 kg Colours: choose from Fassa's 228 colour swatches LS 122 LS 122 Mineral-based smooth coat with satin finish LS 122 is a mineral smoothing based on lime putty and marble powder. LS 122 provides a smooth and compact finish ("marble" effect) for the interior and exterior decoration of buildings, providing very high breathability at the same time. Accordingly, it is used especially for historically and artistically relevant buildings. Marble effect Lime-based mineral decorative application High vapour permeability Specific weight: 1.50 kg/l approx. Grading: < 0.5 mm Yield: approx. 0.50-0.55 m 2 /kg (refined) Package: 25 kg Colours: choose from Fassa's 228 colour swatches 52
decorative finish RC 155 RC 155 Decorative smoothing for interiors RC 155 is a highly natural mineral putty containing lime and select aggregates, with high breathability, designed specifically to obtain a glossy finish with a "salt and pepper" effect on bases previously prepared with fine-grained plaster I 133. Mineral smoothing "Salt & Pepper" finish Very high breathability Specific weight: 1.55 kg/l approx. Grading: < 0.1 mm Yield: approx. 2 m 2 /kg (refined) Package: 25 kg Colours: choose from Fassa's 228 colour swatches SD 111 SD 111 Decorative gloss mineral lime putty for interiors SD 111 is a mineral putty made from lime paste and very fine limestone aggregates. SD 111 is primarily suited for decorating building interiors to enhance their aesthetic qualities, providing very high breathability at the same time. It is possible to obtain smooth and glossy surfaces by applying the product with a metal trowel in several cycles, for marble-like tones and shaded effects, particularly suited for exclusive architecture. Glossy effect Decorative mineral putty High vapour permeability Specific weight: 1.52 kg/l approx. Grading: < 0.1 mm Yield: approx. 1 m 2 /kg (refined) Package: 25 kg Colours: choose from Fassa's 228 colour swatches For the proper use of products, consult the technical data sheets. 53
Excellent elasticity For maintenance and restoration Wide range of colours To minimise the formation of any microcracks Improved resistance to mould and algae 54
ELASTOMER The products from the Elastomer System are particularly suited for the restoration and maintenance of exterior facades. Thanks to their elastic structure, they are the most suitable solution to minimise the first signs of microcracking, protect the facade and provide greater resistance to mould and algae. FOND-ELAST 223 Elastomer evening undercoat with fine mortar appearance p. 56 PE 224 ELAST Elastomer filling finish p. 56 RI-ELAST 225 Elastomer finish coat plaster with rustic appearance p. 57 55
ELASTOMER UNDERCOAT fond-elast 223 Fond-elast 223 Elastomer evening undercoat with fine mortar appearance FOND-ELAST 223 is an evening and filling undercoat with fine mortar appearance, high elasticity and water-repellency; it is suitable for application on any finish coat plaster with the aim of minimising the formation of superficial microcracks over time, either as a preventive method or as a solution to an existing problem, prior to the finishing cycles. High elasticity Intermediate for elastomer cycles Excellent filler Suitable for microcracks Specific weight: 1.53 kg/l approx. Dilution with water: up to 10% in volume depending on the tool used for application. Yield: 4-5 m 2 /l approx. per coat. Package: 14 litres Colour: white finish coat paint for exteriors Pe 224 elast PE 224 elast Elastomer filling finish PE 224 ELAST is a protective and decorative water-based paint with high elasticity and water-repellency, suitable to minimise the formation of microcracks over time. It can be applied either as a preventive method or as a solution to an existing problem. Its special formula also provides a film achieving good resistance against the proliferation of mould and algae. Suitable for microcracks Excellent elasticity Excellent protection Improved resistance to mould and algae Specific weight: 1.45 kg/l approx. Dilution, in weight, with water: first coat up to 15%, second coat up to 5% for brush application; up to 10-15% for roller application Yield: 5-6 m 2 /l approx. (2 coats) Package: 14 litres Colours: choose from Fassa's 228 colour swatches 56
UNDERCOAT FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER Finish coat plaster Ri-elast 225 RI-elast 225 Elastomer finish coat plaster with rustic appearance RI-ELAST 225 is a protective and decorative finish coat plaster in paste form for exteriors with high elasticity, which minimises the signs of superficial microcracks over time. It can be applied preventively or as a solution to an existing problem. Its special formula also provides a film achieving good resistance against the proliferation of mould and algae. Compliant with standard EN 15824. High elasticity With microfibres Excellent protection Improved resistance to mould and algae Specific weight: 1.85 kg/l approx. Dilution, in weight, with water: up to 2%, if necessary Available in the following gradings: 1-1.5-2 mm Consumption: 1 mm: approx. 2-2.5 kg/m 2; 1.5 mm: approx. 2.3-2.7 kg/m 2; 2 mm: approx. 2.6-3.4 kg/m 2; Package: 25 kg Colours: choose from Fassa's 228 colour swatches For the proper use of products, consult the technical data sheets. 57
ELASTOMER Application cycles finishing cycle for exteriors In cases of microcracking, the recommended cycle for exteriors involves applying FA 249 primer followed by the RI-ELAST 225 finish coat plaster. When using PE 224 ELAST finish coat paint, FOND-ELAST 223, an evening and filling undercoat with fine mortar appearance, must be applied beforehand. For dated walls it is necessary to assess the preventive use of SOL-FIX 211 solvent-based primer in place of FA 249 primer. neutral undercoat FA 249 Primer for acrylic systems filling undercoat Fond-elast 223 Elastomer evening undercoat with fine mortar appearance Finish coat plaster RI-elast 225 Elastomer finish coat plaster with rustic appearance finish coat paint for exteriors PE 224 elast Elastomer filling finish 58 The cycles must be evaluated based on the substrate they will be applied to. Crumbling and unstable substrates will need to be consolidated.
UNDERCOAT FINISH COAT PAINT FOR interiors FINISH COAT PAINT FOR EXTERIORS FINISH COAT PLASTER 59
60 COLOUR System
COMPLEMENTARY PRODUCTS Products that should be used in special cases to complete the Colour System range. SOL-FIX 211 Solvent-based acrylic primer p. 62 IS 510 Siloxane water repellent p. 62 FAST 299 Filling paste p. 62 AM 270 Renovation solution for interiors p. 63 AC 241 Synthetic resin-based adhesion promoter p. 63 61
COMPLEMENTARY PRODUCTS SOL-fix 211 SOL-FIX 211 Solvent-based acrylic primer SOL-FIX 211, thanks to its high penetrating power, is used as an insulating agent, a primer and a stabiliser of masonry work, prior to the application of paints from the Acrylic, Elastomer and Acrylic-Siloxane Systems. High penetrating power Substrate preparation Specific weight: 0.82 kg/l approx. Yield: 5-6 m 2 /l approx. (per layer) The values refer to the application of the product on smooth surfaces with medium absorbency; it is good practice to carry out a preliminary test on the specific wall Package: 20 litres Colour: transparent is 510 IS 510 Siloxane water repellent IS 510 provides greater water repellent properties for the treatment of substrates such as facing brick, concrete and stone materials in general. For marble surfaces it is advisable to perform a preliminary test on a small area in order to check compatibility. It is also used as a protection for lime-based finishes, such as LS 122, or for mineral wall coatings such as RF 100, RM 200, RG 300. IS 510 does not alter the breathability of the wall it is applied to, it penetrates the treated surface without changing its appearance. Maximum protection It does not alter the breathability of the substrate Water-repellent Specific weight: 0.80 kg/l approx. Yield: varies based on the degree of absorption of the treated material Package: 16 litres Colour: transparent FAST 299 FAST 299 Filling paste FAST 299 is a paste product, for interiors, ready for use, with high filling properties. It is used indoors as a filling and smoothing material for plaster and concrete surfaces before applying Acrylic System finishes. Ready for use Easy to use High filling properties Specific weight: 1.70 kg/l approx. Grading: < 0.1 mm Yield: varies based on need (approx. 4-5 m 2 /kg per layer of product) Package: 20 kg Colour: white 62 For the proper use of products, consult the technical data sheets.
COMPLEMENTARY PRODUCTS AM 270 AM 270 Renovation solution for interiors AM 270 is an aqueous solution for interiors which contains special broad-spectrum molecules that help prevent the formation of mould on the applied paint. The solution is also suitable for use on surfaces that are already affected by these types of phenomena and need to be restored with a new cycle of paint treatment. Specific weight: 1.00 kg/l approx. Yield: approx. 8-12 m 2 /l depending on the substrate absorption Package: boxes of 12 1-litre bottles For sanitising cycles for interiors AC 241 AC 241 Adhesion promoter based on synthetic resins AC 241 is an adhesion promoter made from synthetic resins and graded sand which is used to improve the adhesion of gypsum and limegypsum based plasters on concrete surfaces. Adhesion promoter For smooth surfaces Specific weight: 1.50 kg/l approx. Grading: < 0.6 mm Yield: approx. 0.20-3.4 kg/m 2 Package: boxes of 12 1-litre bottles Decoration System The Fassa Bortolo Decoration System developed from 15 years of experience in the paint industry, a select and high quality range of brushes, radiators, fixtures, rollers, trowels and accessories to fulfil the needs of the professionals. Tools produced with select materials designed for easy use, that are easy to handle and long-lasting. For additional information download the brochure from our website www. fassabortolo.com For more information on the complete Fassa Bortolo product range, visit our website www.fassabortolo.com 63
FASSA S.r.l. Via Lazzaris, 3-31027 Spresiano (Treviso) tel. +39 0422 7222 - fax +39 0422 887509 www.fassabortolo.com - fassa@fassabortolo.com DEP102IN 10/2014 PRODUCTION FACILITIES Italy Spresiano (Treviso) - tel. +39 0422 521945 - fax +39 0422 725478 Artena (Rome) - tel. +39 06 951912145 - fax +39 06 9516627 Bagnasco (Cuneo) - tel. +39 0174 716618 - fax +39 0422 723041 Bitonto (Bari) - tel. +39 080 5853345 - fax +39 0422 723031 Calliano (Asti) - tel. +39 0141 915145 - fax +39 0422 723055 Mazzano (Brescia) - tel. +39 030 2629361 - fax +39 0422 723065 Molazzana (Lucca) - tel. +39 0583 641687 - fax +39 0422 723045 Moncalvo (Asti) - tel. +39 0141 911434 - fax +39 0422 723050 Montichiari (Brescia) - tel. +39 030 9961953 - fax +39 0422 723061 Popoli (Pescara) - tel. +39 085 9875027 - fax +39 0422 723014 Ravenna - tel. +39 0544 688445 - fax +39 0422 723020 Sala al Barro (Lecco) - tel. +39 0341 242245 - fax +39 0422 723070 FASSALUSA Lda - Portugal São Mamede (Batalha) - tel. +351 244 709 200 - fax +351 244 704 020 SALES BRANCHES Italy Altopascio (Lucca) - tel. +39 0583 216669 - fax +39 0422 723048 Bolzano - tel. +39 0471 203360 - fax +39 0422 723008 Sassuolo (Modena) - tel. +39 0536 810961 - fax +39 0422 723022 FASSA SA - Switzerland Mezzovico (Lugano) - tel. +41 (0) 91 9359070 - fax +41 (0) 91 9359079 Aclens - tel. +41 (0) 21 6363670 - fax +41 (0) 21 6363672 Dietikon (Zurich) - tel. +41 (0) 43 3178588 - fax +41 (0) 43 3211712 FASSA FRANCE - France Lyon - tel. 0800 300338 - fax 0800 300390 FASSA HISPANIA SL - Spain Madrid - tel. +34 606 734 628 FASSA UK Ltd - United Kingdom Slough - tel. +44 (0) 1753573078