Infrared Receiver Modules SHEET CUSTOMER : DEICE NAME : CODE No. ITEM No. ISSUED : : ROMT538MS : [ CUSTOMER ] ACCEPT No. ACCEPT INSPECTER COMMENT ACCEPT ISSUE REIEW REIEW APPR D ISSUED DEPT. Tel : 82428632840 Fax : 82428610843 http://www.raytron.co.kr Rev 3.0
RECORD OF REISION ROMT538MS 2009... No. PAGE REISED CLAUSE REISION DETAILS Ma Ch AP 1046, MoonjiDong, YusungGu, Daejeon, KOREA TEL : +82428632840 FAX : +82428610843 TEL : +8675527447373 FAX : +8675527447235 RIS09092801
1 of 7 ROMT538MS 1. Description The ROMT5xx Series are miniaturized receiver for infrared remote control system. The Pin Photodiode and preamplifier are assembled on lead frame. The epoxy package is designed as IR filter. The module has excellent performance even in disturbed ambient light application and provides protection against uncontrolled output pulses. 2. Features 1) Transfer mold package. 2) Wide operating supply voltage 2.7 ~ 5.5 3) Supply current : 3.3(0.4mA), 5.0(0.42mA) 4) Band pass filter center frequency : 37.9Khz 5) Epoxy IR filter characteristic : 940nm 6) Maximum interference safety against optical and electrical disturbance. 7) Internal filter for a high frequency lighting fluorescent lamp. 8) Internal PullUp output. 9) Lead(Pb)free component. 3. Application 1) A instruments (DD, T, SR, Audio, CD player) 2) Home appliances (Air conditioner, Computer, Camera) 3) Remote control for wireless equipment. 4) Infrared remote control Toys. 4. Block Diagram Noise & Gain Ctrl. Pre Amp AGC Limit Amp Band Pass Filter Com. Integrator & Wave Shaping out PD Input Stage Fset Bias Circuit ATC GND 1046, MoonjiDong, YusungGu, Daejeon, KOREA TEL : +82428632840 FAX : +82428610843 TEL : +8675527447373 FAX : +8675527447235 RIS09092801
2 of 7 ROMT538MS 5. ElectroOptical Characteristics 1) Absolute Maximum Ratings (at 25 Unless otherwise note) Parameter Symbol Supply oltage Output Current Iout Operating Temperature Topr Storage Temperature Tstg Soldering Temperature (*1) Tsol (*1) For 10sec (at mounting on PCB with thickness of 1.6mm) Ratings 6.0 2.0 20 ~ +85 30 ~ +90 260, t<10sec Unit ma 2) Recommended Operating Conditions Parameter Symbol Ratings Unit Operating oltage 2.7 ~ 5.5 Input Frequency fin 30 ~ 60 khz 3) ElectroOptical Characteristics (Ta=25 ) Supply oltage Supply Current Peak Wavelength ( 1) B.P.F Center Frequency ( 2) High Level Output oltage ( 1) Low Level Output oltage ( 1) High Level Output Pulse Width ( 1) Low Level Output Pulse Width ( 1) Pullup Resistance Arrival Distance ( 1) Output Form Parameter Symbol Icc λp fo OH OL twh twl Rout D Conditions N/signal (3.0) N/signal (5.0) Burst Wave =600 μs Period = 1.2 ms 1. Distance between emitter and detector specifies maximum distance that output wave form satisfies the standard (fig.2, fig3) under the conditions below against the standard transmitter. ON/OFF pulse width is to be satisfied within 0.3m~ arrival distance length. 2. The following band pass frequencies are available (32.7 khz /36 khz /37.9 khz /40 khz /56.7 khz ) carrier frequencies are adjusted by zenerdiode fusing method. ±0 ±30 Min 2.7 0.3 0.35 0.5 400 400 Active Low Output Typ 0.4 0.42 940 37.9 0.2 94 15 13 Max 5.5 0.5 0.6 0.4 800 800 Unit ma manm khz μsμs kω m m 1046, MoonjiDong, YusungGu, Daejeon, KOREA TEL : +82428632840 FAX : +82428610843 TEL : +8675527447373 FAX : +8675527447235 RIS09092801
3 of 7 ROMT538MS 4) Measurement Conditions 1 Fig.1 Burst wave, Output wave t burst Transmitter output Carrier Frequency(fo), Duty 50% (Input pulse) t burst gap Minimum Burst Length (tburst ) : 12pulses Minimum Gap Time Between the burst (tburst gap) : 16pulses (Output pulse) t WL t WH Data word t data t pause Data word Minimum Gap Time between the data commands (tpause) : 23 ms 2 Fig.2 Application Circuit 47~470Ω Transmitter IRED (I F =>300 ma ) ROM Series out 47 μf μc GND GND Please add the RC filter, resistor(40~470ω) to line and, Condenser(47 μf ~470 μf ) between and GND, in order to reduce the noise from power supply line. In addition, infrared LED used in the transmitter is set to λpeak=940nm and current (IF= >300 ma ) 3 Fig.3 Test Condition of Arrival Distance out Transmitter GND OSC : Indicates horizontal and vertical directions Ambient light source : Detecting surface s illumination shall be 100Lux under ordinary white fluorescence lamp without high frequency lighting. 1046, MoonjiDong, YusungGu, Daejeon, KOREA TEL : +82428632840 FAX : +82428610843 TEL : +8675527447373 FAX : +8675527447235 RIS09092801
4 of 7 ROMT538MS 5) Graph of Electrical/Optical Characteristics [ Fig.1 ] Supply Current vs. oltage [ Fig.2 ] Sensitivity vs. Supply oltage 2.5 100 Supply Current( ma ) 2.0 1.5 1.0 0.5 Relative Sensitivity(%) 80 60 40 20 0.0 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 2.7 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Supply oltage( ) Supply oltage( ) 800 [ Fig.3 ] Output Pulse Width vs. Distance [ Fig.4 ] Relative Sensitivity vs. Direction 0 20 Output Pulse Width( μs ) 700 600 500 400 Relative Radiant( ) 100 90 H 40 60 80 300 0 4 8 12 16 20 24 80 60 40 20 0 Transmission Distance(m) Relative Sensitivity(%) 6) Standard Inspection All output products shall be inspected based on following items. 1 Detecting distance. 2 Current consumption. 3 High level output voltage. 4 Low level output voltage. 5 Output Pulse width. 7) Others In case any trouble or question arise, both parties agree to make full discussion covering the said problem. 1046, MoonjiDong, YusungGu, Daejeon, KOREA TEL : +82428632840 FAX : +82428610843 TEL : +8675527447373 FAX : +8675527447235 RIS09092801
5 of 7 ROMT538MS 6. Reliability Test Item and Standard. 1) All output products shall satisfy below Reliability test items. 2) Related sampling quantity and acceptance/failure judgment standard accordance with MIL standard MILSTD883 is as listed below. 1 Confidence level : 90% 2 LTPD : 10% / 20% No. 1 2 3 4 5 6 7 8 9 10 11 High Temp. Operating ( 1, 2) Low Temp. Operating ( 1, 2) High Temp./ High Hum. Bias ( 1, 2) Temperature Cycle ( 2, 3) P.C.T ( 2) ariable frequency ibration ( 2) Falling ( 4) Test Item High Temp. Storage ( 2) Low Temp. Storage ( 2) Solder Heat ( 2) Solderability ( 5) t=500hr Ta=20, =5.0 t=500hr Test Conditions Ta=+90, t=500hr Ta=30, t=500hr Ta=+85, =5.0 Ta=+85, 85%RH CC=5.0, t=500hr Ta=20 (0.5h) to +85 (0.5h) 20cycle Ta=+121 100%RH, P=1atm, t=4hr Ta=+350±5, 3s Frequency range : 10 to 55Hz/sweep 1min Overall amplitude : 1.5mm X,Y,Z/2h each Height=75cm, 3 times Soldering Temp.: +260±5, 10s Pb free solder : Sn/3.0Ag/0.5Cu Judgment Standard OH (=5.0) High level output voltage OH > 4.5 OL (=5.0) Low level output voltage OL < 0.4 ICC (=5.0) Consumption current ICC < 1.0mA D (=5.0) Arrival Distance D > 10m Leads shall be covered By solder more than 95% Fail(c) / Samples(n) C=0 / n=11 C=0 / n=11 C=0 / n=11 C=0 / n=11 1. Supply voltage of load test is 5.(Standard Jig of Raytron) 2. Electrooptical characteristics shall be satisfied after leaving 2 hours in the normal condition. 3. Temperature cycle test shall repeat above condition 20 times under no load. 4. The test devices shall be dropped three time on the hard wooden board from a height of 75 cm. 5. Reflow Soldering. In cased any trouble or question arises related to above test items, both parties agree to make full discussion and covering the said matters. 1046, MoonjiDong, YusungGu, Daejeon, KOREA TEL : +82428632840 FAX : +82428610843 TEL : +8675527447373 FAX : +8675527447235 RIS09092801
6 of 7 ROMT538MS 7. Packing Specifications 1) Label Specification (Bar Code Sticker) Item Device Lot No. Q ty S / N Remark Label Dimensions Label Type L W (Unit : mm) Remark Label #1 65 40 2) Box Specifications & Packing Method (Unit : mm) Packing Type Materials L x W x H Quantity Shielding Bag Polyethylene 120 x 160 x 0.15 200 pcs Box (#1) Corrugated Cardboard 140 x 217 x 73 1,000 pcs Box (#2) Corrugated Cardboard 395 x 300 x 245 10,000 pcs Box (#4) Corrugated Cardboard 620 x 410 x 520 40,000 pcs 1. Put 200pcs of products in a Shielding Bag. 2. Put 5pcs of Shielding Bag. 4. Put 4pcs of #2 packing boxes in a #4 packing box. 3. Put them(10pcs of #1) in a #2 packing box. 1046, MoonjiDong, YusungGu, Daejeon, KOREA TEL : +82428632840 FAX : +82428610843 TEL : +8675527447373 FAX : +8675527447235 RIS09092801
7 of 7 ROMT538MS 8. Appearance & Dimensions (mm) 1. Pin Config. 1out 2GND 3 2. G.T : ±0.5 1046, MoonjiDong, YusungGu, Daejeon, KOREA TEL : +82428632840 FAX : +82428610843 TEL : +8675527447373 FAX : +8675527447235 RIS09092801