APAS-114 INSTRUCTION MANUAL

DJ System With Bluetooth Wireless Technology Model Number APAS-114 INSTRUCTION MANUAL AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

Welcome Congratulations on choosing to buy a BAUHN product. All products brought to you by BAUHN are manufactured to the highest standards of performance and safety and, as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 1 Year Warranty. We hope you will enjoy using your purchase for many years to come. ii AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

Contents Welcome ii Warranty Details iv General Safety Instructions 1 Product Overview 3 Controls and Connections 4 Getting Started 6 Instructions 8 Other Useful Information 12 Repair and Refurbished Goods or Parts Notice 15 AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 iii

DJ System with Bluetooth Wireless Technology Warranty Details The product is guaranteed to be free from defects in workmanship and parts for a period of 12 months from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our discretion, solely at our option with no charge for parts and labour. The benefits conferred by this warranty are in addition to all rights and remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and to compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 iv

General Safety Instructions Read this manual thoroughly before first use and keep it in a safe place for future reference, along with the warranty card, purchase receipt and carton. The safety precautions enclosed herein reduce the risk of fire, electric shock and injury when correctly adhered to. Follow all instructions and take notice of all warnings to reduce the risk of fire or electric shock. Important Warnings and Cautions! Do not open: To prevent contact with high voltage components inside, do not attempt to open the equipment. There are no user-serviceable parts inside. Do not repair: If the unit requires service, call our after sales support line for advice. Do not attempt to repair the unit yourself; only have it serviced by qualified personnel. Electrical Safety and Cord Handling Power supply: This system can be powered three different ways: (a) by connection to the mains power supply with the supplied power cord, (b) via the rechargeable 12V 4.5Ah in-built battery, or (c) via a DC power supply (not included). If connecting to a DC power supply, make sure it provides a minimum of 50W. Voltage: Before connecting this equipment to the mains power supply, make sure your outlet voltage corresponds to the voltage stated on the appliance rating label (230V/50-60Hz). Mains power connection: When connecting this equipment to the mains power supply, only use the cord and plug supplied. Align the plug properly and insert it fully. Do not overload the power outlet. Protect from moisture: Do not expose this equipment, the power supply cord or the plug to rain or moisture. Do not use it anywhere near water or where water splashes or drips, such as in a wet basement or near a swimming pool. Do not touch the power plug with wet hands. Damaged cord: When the power cord is damaged, it must be replaced by the manufacturer or similarly qualified personnel in order to avoid a hazard. Protect the power cord: Do not let the cord hang over the edge of a table or counter, or touch any hot surface. Do not allow anything to rest on or roll over the power cord. Run any cords so no one steps on or trips over them. Do not run the cord near heatproducing appliances such as radiators or stoves. Disconnect: Switch OFF and unplug the unit when it is not going to be used for a while. Grasp the plug, not the cord, when disconnecting. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 1

General Safety Instructions (Cont.) Usage Environment Location: When using the equipment, make sure to place it: In a well ventilated area, keeping a clearance of at least 20cm to the wall or other equipment to ensure proper ventilation. Away from heat sources such as radiators, heat registers, stoves or other equipment (including amplifiers) that produce heat. Away from areas with high temperatures, high humidity or direct sunlight. Away from excess dirt and dust. Away from open windows and any place where water or metal objects may get into the equipment and damage it. Power connection: When using a power socket or appliance coupler as a power ON/ OFF device, please ensure that the power ON/OFF device can be easily accessed and operated. Usage Conditions and Restrictions Instructions: Follow the instructions in this manual when installing and adjusting this equipment. Only adjust those controls that are covered in this instruction manual, as improper adjustment of other controls may result in damage. If this happens, unplug the equipment and have it serviced by appropriately qualified personnel. Usage restriction: The equipment is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children: Young children should be supervised to ensure they do not play with the equipment. Close supervision is always necessary when an appliance is used by or near children. Ventilation: Openings on the cabinet are provided for ventilation and to protect the unit from overheating. To ensure proper operation, do not cover the openings with things such as newspapers, tablecloths, curtains etc. Protect the equipment: Prevent metal objects falling onto or into the equipment. Do not place heavy objects on top of the equipment or step on it. Do not place objects filled with water (such as vases), or naked flame sources (such as candles), on top of the equipment. If liquid or metal parts enter the system, unplug the power cable immediately and call our after sales support centre to arrange a service before further use. Cleaning: Unplug the equipment from the power outlet before cleaning. Clean the equipment only with a dry, clean cloth. Do not use liquid or aerosol cleaners or volatile solvents. Liability: We accept no liability for any damage or lost data caused by noncompliance with these instructions or mishandling of the equipment. 2 AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

Product Overview Front View A Telescopic Luggage Handle B Carry Handle C Speaker Unit D Sturdy Feet (2) E Wheels (2) A B C D E Top View: Control Panel See pages 4-5 for a description of all controls and connections. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 3

Controls and Connections Control Panel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 5 Band Equaliser: Adjust the music play back to your preference. 2 Repeat Button: Press to repeat the current track, press again to repeat all. 3 USB/SD Indicator Light: Indicates USB/SD card mode. 4 SD Card Slot: Insert an SD card. 5 USB Port: Insert a USB device. 6 Bluetooth Indicator Light: Indicates Bluetooth mode. 7 Pause/Play Button: Press to play music track, press again to pause track. 8 Next Track Button: Press to play the next track / channel on FM radio mode. 9 Source Button: Select mode from AUX (default) / USB/ SD / FM radio or Bluetooth mode. 10 Previous Track: Press to play the previous track / channel on FM radio mode. 11 Guitar Input Socket: Insert the guitar connector. 12 Guitar Volume Control: Adjust the guitar volume. 13 Microphone Echo Control: Adjust the microphone echo. 14 Microphone Volume Control: Adjust the microphone volume. 15 Karaoke Mode Button: While the speaker system is playing music: Press the button (down) for the karaoke function, with music. Release the button (up) for the microphone (voice only), without music. 16 Microphone Input Socket: Connect a wired microphone. 17 Power Indicator: Indicates that the power is ON. 18 Master Volume Control: Adjust the volume. 19 Battery Charging Indication Light: Indicates that the battery is charging. 4 AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

Controls and Connections (Cont.) Back Panel 20 21 22 25 23 24 26 20 3.5mm Signal Input Socket: Connect a computer, TV or portable music device. 21 RCA Input: Connect a TV, DVD or audio playback equipment. 22 RCA Output: Connect additional speakers if required. 23 DC input/battery Charge/AC Input Switch: Power source switch. 24 AC Power Switch: ON/OFF switch for AC power. 25 DC Power Supply Input: Connect to the DC power supply source. 26 AC Power Input: Connect the power cable. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 5

Getting Started Power Source This system can be powered in three different ways: (a) By connection to the mains power supply with the supplied power cord. (b) Via the rechargeable 12V 4.5Ah built-in battery. (c) Via an external DC power supply (not included). AC Mode (mains power supply) Connect the power cable to the AC power input, then insert the plug into an appropriate wall outlet. Set the AC POWER SWITCH to ON. Set the POWER SOURCE to AC mode. The system is now in operating mode and will be powered by ~230V/50-60Hz. DC Mode If the equipment is connected to the mains power supply, disconnect the power cable. Set the AC POWER SWITCH to OFF. Set the POWER SOURCE to DC INPUT. External DC power supply To power the unit via an external DC power supply, connect the external power supply's positive pole to the red terminal and the negative pole to the black terminal. The system will now be powered by the external DC power supply. NOTE: The external DC power supply must be DC 12V-15V with a minimum output power of 50W. Internal 12V 4.5Ah battery power supply If no external power supply is connected, the system will automatically be powered by the built-in 12V 4.5Ah battery when the power source is set to DC INPUT. AC Power Switch Set to ON to use the equipment in AC mode, or to charge the built-in battery. Set to OFF to use the equipment in DC mode. To switch the system OFF, set the POWER SOURCE to AC mode and the AC POWER SWITCH to OFF. 6 AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

Getting Started (Cont.) Charging the Battery This DJ System is equipped with a built-in 12V 4.5Ah rechargeable battery. Before the first three times that you are going to use the system, this battery should be charged for a minimum of 12 hours. To charge, proceed as follows: Set the AC POWER SWITCH to ON. Set the POWER SOURCE to BATTERY CHARGE. The built-in battery will now be charged from the mains power supply. A full charge takes about 12-14 hours at this stage. When the battery is fully charged, set the AC POWER SWITCH to OFF and disconnect the power supply. Important Notes Concerning the Battery When the battery is low or has run out, it is important to extend the recharging time to 24 hours. Recharging it for a shorter time may reduce the battery life, damage the battery and cause the battery to never be fully charged, which will result in a shorter time of operation. Do not open the cover to the battery housing. Only professional technicians should open this system if the battery needs to be replaced. In such a case, contact our after sales support centre for advice. Only a battery with the same specifications may be used to power this equipment. An unsuitable battery may damage the system or cause malfunction. Do not use this battery in other equipment. If you are not going to use this system for a long period of time, please recharge the battery at least once every 3 months to avoid letting your battery sit dormant for a long period of time and risk battery failure. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 7

Instructions Streaming Audio via Bluetooth Wireless Technology Pairing With a New Bluetooth Enabled Device Press the Source Button repeatedly until Bluetooth mode is selected. A beep will sound and the Bluetooth indicator light will start flashing fast. The DJ System is now ready for pairing. Turn on the Bluetooth function of your device and scan available Bluetooth enabled devices nearby. Select APAS-114 from the device list to pair. Enter 0000 if your Bluetooth enabled device prompts you for a passcode. If pairing is successful, the Bluetooth indication light will stop flashing. If you play a song, the Bluetooth indication light will flash slowly. If you cannot pair the DJ System with your Bluetooth enabled device, turn both the DJ System and your Bluetooth enabled device OFF and ON and then try again. NOTE: If your Bluetooth enabled device does not support A2DP, you might not be able to pair with the DJ system. Connecting to Bluetooth Devices Stored in Memory Turn on the DJ System and press the SOURCE button to select Bluetooth mode. The DJ System will start searching for the previously paired devices. If an available device is found, the system will connect to the Bluetooth device automatically. Playing Audio Via Bluetooth Wireless Technology After successful connection you can play music from your Bluetooth enabled device wirelessly on the DJ System. Press the button to play or pause music. Press the or button to skip to the previous or next track. NOTES: Refer to the manual of your Bluetooth enabled device for more information about the Bluetooth function on the device. If your Bluetooth enabled device does not support A2DP profile, it can be paired and connected but will not play audio through the DJ System. When you pair and connect your computer to the DJ System, you may need to change the sound setting on your computer. 8 AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

Instructions (Cont.) Audio Input Operation This unit is equipped with 2 input sockets for audio playback from external devices: a 3.5mm input socket and a stereo RCA socket. If your audio device has a 3.5mm audio output socket (line-out or headphones), use the included 3.5mm audio cable to connect the DJ System to your device. If your audio device has RCA output sockets, use RCA cables to connect the DJ System to your device. Turn on both the DJ System and the external audio device. Adjust the volume according to the source you are using. USB and SD Card Operation This unit has a USB port and SD Card slot on the control panel at the top of the DJ System. The ports accept standard USB drives and SD cards for playback of MP3 and WMA files stored on them. Press the SOURCE button repeatedly until USB or SD Card mode is selected. Insert your USB device into the USB port (or the SD card into the card slot) and the unit will start playing automatically. Press the or button to select the previous or next track. Press the button to temporarily pause the track. Press the REPEAT button to repeat the current track, press it again to repeat all tracks. NOTE: When you insert a USB device or SD card, the DJ System will automatically select the appropriate mode and start playing. When you have both a USB device and an SD card inserted, you will have to press the SOURCE button repeatedly until the appropriate source is selected. FM radio In order to use FM radio press SOURCE repeatedly until you hear FM radio. Press the button to activate auto search. Your Portable Entertainment System will search for radio stations and save them on available channels. Use the or button to navigate through saved channels. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 9

Instructions (Cont.) Wireless Microphone This DJ System comes with a wireless microphone for announcements or karaoke entertainment. Before first use, you will have to install two AA batteries (not included). Battery Installation Open the cover to the battery compartment at the back of microphone (Fig. 1). Fig. 1 Insert 2 AA size batteries, making sure to match the polarity markings (+ / -) on the batteries with those inside the compartment. Close the battery compartment. Battery Precautions CAUTION: Danger of explosion! Ensure to insert batteries according to the polarity markings inside the battery compartment. Replace all batteries at the same time with fresh batteries of the same size and type. Do not mix old and new batteries, different types of battery (alkaline, carbon-zinc or rechargeable), or rechargeable batteries of different capacities. Mixing different types of battery could cause battery leaks or ruptures. Note that there are rechargeable and non-rechargeable batteries. Do not attempt to charge non-rechargeable batteries. Remove the batteries when the microphone is not in use for a long time to avoid leakage. Batteries can leak chemicals that can damage electronic parts. Dispose of batteries promptly and properly, observing any local hazardous waste regulations. Do not burn or bury them. Keep batteries away from children. If you suspect a battery may have been swallowed, seek immediate medical assistance. 10 AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

Instructions (Cont.) Microphone Operation The microphone has one switch at the front, as illustrated in Fig.2. Fig. 2 Push the switch up to the top to switch ON the microphone. For best reception, do not move the wireless microphone further than 15 meters away from the DJ System. Push the switch to the middle position to mute the sound temporarily; the indicator light will blink once. Push the switch down to switch OFF the microphone. Important Notes While using the microphone, avoid being close to metal surfaces or walls, as they may affect the wireless transmission. To get the best singing performance, keep the microphone within 5-15cm of the mouth and at a 45 degree angle. When using the microphone, always pay attention to the battery. If the battery is low, the indicator light will come on and the performance will progressively become poor. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 11

Other Useful Information Cleaning and Maintenance CAUTION! To prevent a fire or shock hazard, always switch OFF and disconnect the DJ System from the AC power supply before cleaning. Never allow any water or other liquid to get inside the DJ System while cleaning. The speaker cabinet may be cleaned with a soft, dry dust cloth. DO NOT use any of the following substances for cleaning the speaker cabinets or tripods: NO wax or polish sprays. NO abrasive cloths or polishes. NO chemical cleaning agents. DO NOT remove the cover or the back of this equipment. There are no userserviceable parts inside. DO NOT attempt to repair or service the equipment yourself. All servicing should be referred to qualified service personnel. Contact our after sales support centre for advice on repair or service. 12 AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

Other Useful Information (Cont.) Technical Specifications Output Power Frequency Response 50W 20Hz~22kHz Distortion <0.15% S/N Ration Speaker Drivers Power Supply >85dB Woofer 8" x 1 Tweeter 2" x 1 Rechargeable 12V 4.5Ah battery External DC power supply 12-15V (power >50W) Built-in transformer ~230/50-60Hz, 50W Product Size 293 x 263 x 460 mm (L x W x H) Bluetooth USB and SD Card Version 2.1, supports A2DP profile Support MP3 and WMA format files Responsible disposal At the end of its working life, do not throw this device out with your household rubbish. Electrical and electronic products contain substances that can have a detrimental effect on the environment and human health if disposed of inappropriately. Observe any local regulations regarding the disposal of electrical consumer goods and dispose of it appropriately for recycling. Contact your local authorities for advice on recycling facilities in your area. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 13

This page has been left blank intentionally. 14 AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015

DJ System with Bluetooth Wireless Technology Repair and Refurbished Goods or Parts Notice Unfortunately, from time to time, faulty products are manufactured which need to be returned to the supplier for repair. Please be aware that if your product is capable of retaining user-generated data (such as files stored on a computer hard drive, telephone numbers stored on a mobile telephone, songs stored on a portable media player, games saved on a games console or files stored on a USB memory stick) during the process of repair, some or all of your stored data may be lost. We recommend you save this data elsewhere prior to sending the product for repair. You should also be aware that rather than repairing goods, we may replace them with refurbished goods of the same type or use refurbished parts in the repair process. Please be assured though, refurbished parts or replacements are only used where they meet ALDI s stringent quality specifications. If at any time you feel your repair is being handled unsatisfactorily, you may escalate your complaint. Please telephone us on 1300 886 649 or write to us at: Tempo (Aust) Pty Ltd ABN 70 106 100 252 PO BOX 6056 Frenchs Forest, Sydney, Australia NSW 2086 Tempo Help Desk: 1300 886 649 (Aust) (Operating Hours: Mon-Fri 08:30AM to 06:00PM EST) Email: info@tempo.org AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015 15

Warranty returns Should you for any reason need to return this product for a warranty claim, make sure to include all accessories with the product. Product does not work? If you encounter problems with this product, or if it fails to perform to your expectations, make sure to contact our After Sales Support Centre on 1300 886 649 before returning it to the store for a refund. AUS 1300 886 649 Model: APAS-114 Product Code: 47396 10/2015