CTS/TITAN Injection Bore System

CTS/TITAN Injection Bore System Tie Back Anchors Soil Nails & Micropiles G IBO : Injection BOring G Dynamic pressure grouted, casing free single step installation G Suits all ground conditions G Rapid, effective ground and structural stabilisation CON-TECH SYSTEMS LTD HQ: 8150 RIVER ROAD DELTA BC, V4G 1B5 CANADA PH: (604) 946-5571 FAX: (604) 946-5548 WESTERN DIVISION: DELTA, BC, PH: (604) 946-5571, FAX: (604) 946-5548 DESCANSO CA, USA, PH: (619) 659-9931 FAX: (619)659-9932, E-MAIL: ctswest@contechsystems.com EASTERN DIVISION: ELIZABETHTOWN ON CANADA PH: (613) 342-0041, FAX: (613) 342-0609 RICHEY FL, USA, PH: (866) 848 6800 CHARLOTTE NC, USA, (704) 494-3989 E-MAIL: ctseast@contechsystems.com

CON-TECH SYSTEMS LTD CTS Parts-List Index 1 Technical Data 3 2 Drill Bit Selection Chart 5 3 R32/20 7 4 TITAN 30/11, TITAN 30/14 & TITAN 30/16 9 5 TITAN 40/16 & TITAN40/20 13 6 TITAN 52/26 17 7 TITAN 73/56, TITAN 73/53 TITAN 73/45 & TITAN 73/35 19 8 TITAN 103/78 & TITAN103/51 21 9 TITAN 130/60 23 Disclaimer: All products are subject to change at any time without notice. Con-Tech Systems will make the best effort to keep you informed about any changes. Please check our website (www.contechsystems.com) for updates. All photos are for illustrative purpose only; weights are approximate. Products must be used in conformity with safe practices and applicable codes. For best performance results, refere to CTS/TITAN/IBO installation procedures 2

CTS CON-TECH SYSTEMS LTD CTS/TITAN Technical Data Rod Size Area Load Capacity Outside Diameter Weight D Ø / INNER Ø Ultimate Yield Max. Test Design 1 Design 2 Effective Nominal G.U.T.S. Temp. Anch. 60% G.U.T.S. d Ø D Ø mm in 2 kips kips kips kips kips in in lbs./lf. mm 2 kn kn kn kn kn mm mm kg/m 30/16 0.59 49.5 40.5 39.6 34.6 29.7 1.02 1.18 1.8 L.H. THREAD 382 220 180 176 154 132 26 30 2.7 30/14 0.61 58.5 49.5 46.8 40.9 35.1 1.03 1.18 1.9 L.H. THREAD 395 260 220 208.0 182 156 26 30 2.9 32/20 0.60 65.4 54.9 52.3 45.8 39.3 1.10 1.26 2.2 L.H. THREAD 389 291 244 233 204 175 28 32 3.2 30/11 0.69 72.0 58.5 58 50.4 43.2 1.03 1.18 2.2 L.H. THREAD 446 320 260 256 224 192 26 30 3.3 40/20 1.13 121.2 96.7 95.6 84.8 72.7 1.42 1.57 3.8 L.H. THREAD 726 539 430 425 377 323 36 40 5.6 40/16 1.36 148.4 118.1 116.9 103.9 89.0 1.42 1.57 4.7 L.H. THREAD 879 660 525 520 462 396 36 40 7.0 52/26 2.07 208.9 164.2 160.1 146.2 125.3 1.92 2.05 6.7 L.H. THREAD 1337 929 730 712 650 557 49 52 10.0 73/56 2.19 268.5 176.5 174.3 173.2 161.1 2.76 2.87 7.5 R.H. THREAD 1414 1194 785 775 770 716 70 73 11.1 73/53 2.53 260.9 218.1 208.7 182.6 156.5 2.76 2.87 8.3 R.H. THREAD 1631 1160 970 928 812 696 70 73 12.3 73/45 3.50 366.5 265.3 263.1 256.6 219.9 2.76 2.87 12.0 R.H. THREAD 2260 1630 1180 1170 1141 978 70 73 17.8 73/35 4.20 445.2 304.7 302.5 301.3 267.1 2.76 2.87 14.2 R.H. THREAD 2710 1980 1355 1345 1340 1188 70 73 21.2 103/78 4.88 513.2 404.8 400.3 359.2 307.9 3.94 4.06 16.7 R.H. THREAD 3146 2282 1800 1780 1597 1369 100 103 24.9 103/51 8.53 778.1 618.4 616.1 544.6 466.8 3.94 4.06 29.2 R.H. THREAD 5501 3460 2750 2740 2422 2076 100 103 43.4 127/111* 4.65 539.7 407.0 404.8 377.8 323.8 3.94 4.06 15.8 R.H. THREAD 3000 2400 1810 1800 1680 1440 100 103 23.5 130/60 14.79 1785.5 1180.6 1173.8 1169.3 1071.3 4.92 5.12 50.4 R.H. THREAD 9540 7940 5250 5220 5200 4764 125 130 75.0 1 2 Temporary Anchors ; Permanent Anchors Imperial values converted from metric values; October 2006 Note: Subject to change without notice. Shear Force Allowable shear force is determined by the formula: Q allow = Yield *A 1.75* 3 A: (Steel) Area Certified to ISO 9001 TITAN 127/111: Allowable bending moment = 23.9 knm (737.5 lbsft) 3

CON-TECH SYSTEMS LTD CTS/TITAN Technical Data CTS NOTES: THE TITAN THREAD MEETS AND EXCEEDS ASTM REQUIREMENTS FOR RE-BAR DEFORMATIONS (ASTM-A-615). GROUT CRACK WIDTH = O.1mm AT 1.25 OF DESIGN LOAD. NO ADDITIONAL CORROSION PROTECTION IS REQUIRED IBO/TITAN BARS ARE ROLLED OUT OF HIGH QUALITY STEEL TUB- ING FOR SOIL NAILS, ROCK AND SOIL ANCHORS AND MINI / MICRO PILES. THEIR UNIQUE INSTALLATION METHOD, I.E. DYNAMIC (TREMI)- GROUTING DURING DRILLING ASSURES CONTINUOUS GROUT COVER FOR GOOD CORROSION PROTECTION AND SUPERIOR SKIN FRICTION AND BOND. FOR ADDITIONAL CORROSION PROTECTION, BARS AND HARD- WARE CAN ALSO BE EPOXY COATED, acc. to ASTM A-934, ASTM A-775 or AASHTO M284 ZINC METALLIZED, acc. to ASTM A-153 or AASHTO M232 HOT DIP GALVANIZED, acc. to ASTM A-153 or AASHTO M232 OR BE SUPPLIED IN (INOX) STAINLESS STEEL. INSTEAD OF EXTRA CORROSION PROTECTION, THE SACRIFICIAL- STEEL METHOD, CHOOSING THE BAR LARGER THAN REQUIRED, CAN BE USED. THIS METHOD IS VERY COMMON IN EUROPE AND FOR REINFORCED EARTH SYSTEMS. STOCKED TITAN BARS: 30/16, R32/20, 30/11, 30/14, 40/20, 40/16, 52/26, 73/53, 103/78, 103/51. 4

CTS CON-TECH SYSTEMS LTD Drill Bit Selection Chart TITAN 30/11(left) TITAN 40/16 (left) for weathered soft rock and gravel hardness < 70 MPa Button Type Button Type hardness HV 700 hardness HV 700 42 mm Ø / 46 mm Ø / 51 mm Ø / 55 mm Ø 70 mm Ø for hard rock, granite, dolomite, standstone, hardness 70-150 MPa Carbide Offset Cross Cut Carbide Offset Cross Cut hardness HV 1800 hardness HV 1800 46 mm Ø 70 mm Ø Micro Piles DIN 4128 / Soil Nails / Anchors DIN 4125 for mixed soil with obstacles > 50 S.P.T. TITAN TITAN TITAN TITAN TITAN TITAN 30/11(left) 40/16 (left) 52/26 73/53 (right) 103/78 (right) 103/51 (right) Cross Cut Cross Cut Cross Cut Cross Cut Cross Cut Cross Cut Drill Bit Drill Bit Drill Bit Drill Bit Drill Bit Drill Bit hardness HV 375 hardness HV 375 hardness HV 375 hardness HV 375 hardness HV 375 hardness HV 375 90 mm Ø 90 mm Ø 115 mm Ø 130 mm Ø 175 mm Ø 175 mm Ø 115 mm Ø 130 mm Ø 175 mm Ø for clay, soft soil and sand/gravel < 50 S.P.T. Clay Bit Clay Bit Clay Bit Clay Bit Clay Bit Clay Bit hardness HV 270 hardness HV 270 hardness HV 270 hardness HV 270 hardness HV 270 hardness HV 270 75 mm Ø 110 mm Ø 130 mm Ø 200 mm Ø 280 mm Ø 280 mm Ø 95 mm Ø 150 mm Ø for hard or high quarzite rock, reinforced concrete B25 at the beginning > 70 MPa Button Type Button Type Button Type Button Type Button Type carbide tipped carbide tipped carbide tipped carbide tipped carbide tipped hardness HV 1800 hardness HV1800 hardness HV 1800 hardness HV 1800 hardness HV 1800 90 mm Ø 115 mm Ø 130 mm Ø 175 mm Ø 175 mm Ø for directional stability of + 2 % of the total length Carbide Cross Carbide Cross Cut 3-step Cut 3-step carbide tipped carbide tipped hardness HV 1800 hardness HV 1800 (75 mm Ø) 90 mm Ø explanation to different - Hardness to Mohs e.g.diamant 10, carbide 9,5, correspond to HV 1800 (Hardness to Vickers),quarzite 7, slate 2,5 declarations of hardness - HRC 60 (Hardness to Rockwell C) correspond to HV 700 (Hardness to Vickers), HRC 38 correspond to HV 375 and rock hardness: - 70 MPa (soft soil and loose sand/gravel) - 70 150 MPa (for hard rock, like dolomit, granite, sandstone) AV8/B1-6 - S.P.T. value (Standard Penetration Test) 5

CON-TECH SYSTEMS LTD CTS/TITAN CTS Page left blank intentionally 6

CTS CON-TECH SYSTEMS LTD CTS/TITAN R32/20 CTS Injection Bore Hollow Bar System R32/20 TITAN Injection Hollow Bar, 32/20 mm, design load (60% GUTS) 175 kn, left hand threaded in lengths of 3 m black part.no. R32-0127 3.20 kg/m pc Spherical Collar Nut black, part.no. R32-0126 0.35 kg pc. stock Coupling black, part.no. R32-0124 0.43 kg pc. stock CTS Drill Bit - Carbide 2, (51mm Ø), carbide tipped, part.no. R32-0117 0.37 kg pc. stock CTS Drill Bit - Carbide 2.5, (63.5mm Ø), carbide tipped, part.no. R32-0119 0.37 kg pc. stock TITAN Drill Bit - Soil Bit Y-Cut 3, (76 mm Ø), part.no. R32-0115 0.69 kg pc. stock TITAN Drill Bit - Clay bit 75 mm Ø for soft soil and loose sand/gravel, induction hardened part.no. R32-0116 0.44 kg pc. stock Flushing Head 32/20 available for R 32* (1-1/4"), R 38* (1-1/2"), T 38*, T 45*, for left hand rotary/percussion drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 3/4 ) male for grout hose, with lubrication nipple, to be used in connection with holder only, incl. transport box, length 265 mm, part.no. P32-001/.002/R32-0113/P32-003 14.00 kg pc. st. T38 complete set of spare seals for R 32 - T 45 flushing heads (2 seals 63 x 78 x 11.4 mm plus 2 guide rings 63 x 68 x 6.3 mm) part.no. T30-0369 set stock Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*, to be fixed on to the mast of the drill rig, fixing position: hammer fully extended and spring released part.no. T30-0370 5.90 kg pc. stock CTS Grout Swivel - T38m/T38m for left hand rotary/percussion drilling and for flushing with water, grout or air 1 NPT male for grout hose connection part.no. TAC-003 6.75 kg pc. stock CTS Adaptor Couplers - T38/R32 part.no. MIC-0032 3.2 kg pc. stock * please specify when ordering Drill Connectors or flushing heads for other drill threads on request 7

CON-TECH SYSTEMS LTD CTS Page left blank intentionally 8

CTS CON-TECH SYSTEMS LTD CTS/TITAN 30/16 & 30/11 CTS/TITAN Injection Bore Hollow Bar System 30 / 16 TITAN Injection Hollow Bar, 30/16 mm, design load (60% GUTS) 132 kn. left hand threaded, suitable for all 30/11 accessories, in 3m lengths. black part.no. T30-0341 2.87 kg/m pc. stock CTS/TITAN Injection Bore Hollow Bar System 30 / 14 TITAN Injection Hollow Bar, 30/14 mm, design load (60% GUTS) 156 kn, left hand threaded, in 3m lengths black part.no. T30-0004 3.29 kg/m pc. stock CTS/TITAN Injection Bore Hollow Bar System 30 / 11 TITAN Injection Hollow Bar, 30/11 mm, design load (60% GUTS) 192 kn, left hand threaded, in 3m lengths black part.no. T30-0351 3.42 kg/m pc. stock INOX, stainless steel, material no. 1.4462, with approval Z-30.3-6 in 3 m lengths. part.no. T30-0373 3.42 kg/m pc. stock CTS/TITAN 30/16 and 30/11 Injection Anchors are also available in other lengths. Please ask us for pricing. Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors and are also available. Please ask us for pricing. Spherical Collar Nut SW 46 x 35 mm. inclination ± 7.5 black, part.no. T30-0362 0.34 kg pc. stock INOX Sperical Collar Nut, stainless steel, material no. 1.4468, part.no. T30-0358 0.42 kg pc. stock Coupling 38 Ø x 105 mm. with center-stop. black, part.no. T30-0355 0.42 kg pc. stock INOX Coupling, stainless steel, material no. 1.4468, part.no. T30-0357 0.40 kg pc. stock Bearing Plate, 200 x 200 x 8 mm, for shotcrete, black, part.no. T30-0372 2.43 kg pc. stock Bearing Plate INOX, 200 x 200 x 12 mm, stainless steel, hole Ø 38 mm, material no. 1.4301 part.no. T30-0359 3.85 kg pc. stock Steel ball 80 mm Ø, hole Ø 32 mm, max. inclination ± 36, black part.no. P30-001 1.87 kg pc. Plate for Steel Ball, 300 x 200 x 23 mm (without steel ball) to be used on four double U-300 walers, spaced max. 150 mm black part.no. PAC-002 13.00 kg pc. Geotextile Fixing Plate, 285 mm Ø for CTS/TITAN 30/11 and 40/16 galv. part.no. P30-003 6.00 kg pc. 9

CON-TECH SYSTEMS LTD CTS/TITAN 30/16 & 30/11 CTS Wedge Disc 30/11, 12, allows 3 x 12 angle, black, weldable part.no. T30-0361 0.91 kg pc. Adaptor for Injection Hollow Bar 30/11 on drill bit 40/16 part.no. T30-0334 0.21 kg pc. Drill Bits TITAN Drill Bit - Button Type 42, (42 mm Ø), hardness HRC 54, for hand-held rotary percussion drills, for soft rock and concrete part.no. P30-004 0.28 kg pc. TITAN Drill Bit - Button Type 46, (46 mm Ø), hardness HRC 54, with top and radial flushing holes, suitable for airtrack drilling machines for harder rock and concrete part.no. T30-0344 0.32 kg pc. stock TITAN Drill Bit - Button Type 51, (51 mm Ø), hardness HRC 54, with top and radial flushing holes, suitable for airtrack drilling machines for harder rock and concrete. part.no. P30-005 0.34 kg pc. TITAN Drill Bit - Button Type 55, (55 mm Ø), for weathered soft rock and gravel part.no. T30-0345 0.38 kg pc. stock TITAN Drill Bit - Carbide Offset Cross Cut 46, (46 mm Ø) carbide tipped, part.no. T30-0346 0.37 kg pc. stock CTS/TITAN Drill Bit - Carbide 2 (51 mm) carbide tipped, part.no. T30-0349 0.63 kg pc. stock CTS/TITAN Drill Bit - Carbide 2.5 (63 mm) carbide tipped, part.no. T30-0350 1.46 kg pc. stock CTS/TITAN Drill Bit - Carbide 3 (76 mm) carbide tipped, part.no. T30-0375 1.7 kg pc. stock TITAN Drill Bit - Carbide Cross Cut 2-Step 75, (75 mm Ø) drill bit for directional stability, cuts through several hard layers of soil/rock part.no. T30-0347 0.84 kg pc. TITAN Drill Bit - 3 Cut 76, (76 mm Ø) with recess center buttons hardened to 57 Rc part.no. P30-006 0.69 kg pc. TITAN Drill Bit - Cross Cut 90 mixed Ground, (90 mm Ø) part.no. T30-0007 1.27 kg pc. stock TITAN Drill Bit - Clay bit 75 mm Ø for soft soil and loose sand/gravel. induction hardened part.no. T30-0348 0.44 kg pc. stock TITAN Drill Bit - Clay bit 95 mm Ø for soft soil and loose sand/gravel. induction hardened part.no. T30-0003 0.55 kg pc. stock Piling Cone 75, (75 mm Ø), with backwards pointing injection hole part.no. T30-0364 0.68 kg pc. Centralizer TITAN 30, 70 mm Ø, for 20 mm grout cover, cast iron black part.no. T30-0335 0.23 kg pc. stock 10 Centralizer TITAN 30, 88 mm Ø, cast iron to seal bore holes of 33 mm up to 56 mm Ø black part.no. P30-007 0.27 kg pc.

CTS CON-TECH SYSTEMS LTD CTS/TITAN 30/16 & 30/11 Bore Hole Stopper screws on to the anchor, material PE, to seal bore holes of 33 mm up to 56 mm Ø part.no. T30-0365 0.10 kg pc. Eye bolt, 35 mm eye diam., SWL 30 kn galvanized part.no. P30-008 0.50 kg pc. Eyebolt, inside Ø, 40/30 mm, for shackles max. M 30, SWL 150 kn galvanized part.no. T30-0010 1.90 kg pc. stock Load Indicator for 30/11, to indicate loads of 70, 160 and 180 kn, retracts by a total of 30 mm, LOBA approved galvanized part.no. T30-0367 0.42 kg pc. stock Expansion Shell for 30/11 and 30/16 anchors for drill hole Ø 46 up to 56 mm part.no. T30-0368 0.77 kg pc. Self contained Flushing Head S 22 for 30/11, for left-hand hand-held hammers (no holder required) part.no. T30-0386 5.96 kg pc. stock Flushing Head 30/11, for hexagon S 22 (7/8"), for left hand rotary/percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 1/2") male for grout hose, length 323 mm, to be used in connection with holder only incl. transport box part.no. T30-0336 5.40 kg pc. Complete set of spare seals for S 22 flushing head (2 pieces, 40 x 50 x 7 mm) part.no. TAC-0018 set Holder, spring action, for flushing head 30/11-S 22, bolts on to the mast of the drill rig part.no. TAC-0019 7.28 kg pc. Flushing Head 30/11 available for R 32* (1-¼"), R 38* (1-1/2"), T 38*, T 45*, for left hand rotary and percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 3/4") male for grout hose, with lubrication nipple, to be used in connection with holder only, incl. transport box, length 265 mm, part.no. T30-0339/..0380/..0340/..0379/ 14.00 kg pc. stock complete set of spare seals for R 32 - T 45 flushing heads (2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6,3 mm) part.no. TAC-0005 set stock Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*, to be fixed on to the mast of the drill rig, fixing position: hammer fully extended and spring released part.no. T3AC-0020 5.90 kg pc. stock *please specify when ordering Drill Connectors or flushing heads for other drill threads on request 11

CON-TECH SYSTEMS LTD CTS/TITAN 30/16 & 30/11 CTS Grouting Connector for 30/11 thread Rd 32 x 1/8" male, for high pressure grout-hose DN 20, with handle and lubrication nipple zinc plated part.no. T30-0333 0.92 kg pc. CTS Grout Swivel - T38m/T38m for left hand rotary/percussion drilling and for flushing with water, grout or air 1 NPT male for grout hose connection part.no. TAC-0003 6.75 kg pc. stock CTS Adaptor Couplers - T38/TITAN30 part.no. MIC-0035 2.27 kg pc. stock 12

CTS CON-TECH SYSTEMS LTD CTS/TITAN 40/16 & 40/20 CTS/TITAN Injection Bore Hollow Bar System 40 / 16 TITAN Injection Hollow Bar, 40/16 mm, design load (60% GUTS) 396 kn, continuously left hand threaded, in lengths of 3 m. black part.no. T40-0247 7.00 kg/m pc. stock INOX, stainless steel, material no. 1.4462, in 3 m lengths part.no. T40-0299 7.00 kg/m pc. stock CTS/TITAN Injection Bore Hollow Bar System 40 / 20 TITAN Injection Hollow Bar, 40/20 mm, design load (60% GUTS) 323 kn, in lengths of 3 m black part.no. T42-0002 5.60 kg/m pc. stock CTS/TITAN 40/16 and 40/20 are also available in other lengths. Please ask us for pricing. Galvanized, Metallized or EPOXY Coated Injection Anchors and are also available. Please ask us for pricing. Spherical Collar Nut SW 65 x 50 mm, inclination ± 7. black, part.no. T40-0263 0.87 kg pc. stock INOX Sperical Collar Nut, stainless steel, material no. 1.4468 part.no. T40-0261 0.88 kg pc. stock Coupling, 54 mm Ø x 140 mm, with center-stop, hardened, with 2 rubber seals black part.no. T40-0259 1.12 kg pc. stock INOX Coupling, stainless steel, material no. 1.4468 part.no. T40-0260 1.13 kg pc. stock Bayonet Coupler 63 Ø x 228 mm, recoverable part.no. T40-0291 1.40 kg pc. stock Bearing Plate, 200 x 200 x 12 mm, hole Ø 56 mm, black part.no. T40-0270 3.50 kg pc. stock Bearing Plate, 200 x 200 x 30 mm, hole Ø 56 mm, for anchorpiles, black part.no. P40-001 8.50 kg pc. INOX Bearing Plate, 200 x 200 x 15 mm, hole Ø 54 mm, stainless steel, material no. 1.4301 part.no. T40-0300 4.58 kg pc. Steel ball 80 mm Ø, hole Ø 42 mm, max. inclination ± 36, black part.no. P40-002 1.59 kg pc. Plate for Steel Ball, 300 x 200 x 23 mm (without steel ball) to be used on four double U-300 walers, spaced max. 150 mm black part.no. PAC-001 13.00 kg pc. Wedge Disc 40/16, 12, weldable black part.no. T40-0262 1.43 kg pc. stock 13

CON-TECH SYSTEMS LTD CTS/TITAN 40/16 & 40/20 CTS TITAN Drill Bit - Clay bit 110 mm Ø for soft soil and loose sand/gravel, induction hardened part. no. T40-0255 1.28 kg pc. stock TITAN Drill Bit - HPI-Clay bit 110 mm Ø for jet grouting up to 200 bars, with 2 nozzles, 2,3 mm Ø, part.no. T40-0254 1.34 kg pc. stock TITAN Drill Bit - Clay bit 150 mm Ø induction hardened part.no. T40-0297 1.5 kg pc. stock TITAN Drill Bit - Button Type 70, (70 mm Ø ), for soft rock and gravel, hardness HRC 54, with top and radial flushing holes, screw-on type. part.no. T40-0250 0.68 kg pc. stock TITAN Drill Bit - Carbide button drill bit 90, (90 mm Ø ), screw-on type. part.no. P40-003 1.27 kg pc. TITAN Drill Bit - Carbide Cross Cut 70, (70 mm Ø), for hard rock, screw-on type part.no. T40-0252 0.98 kg pc. stock CTS/TITAN Drill Bit - Carbide 3 (76 mm) carbide tipped, part.no. T40-0257 1.75 kg pc. stock CTS/TITAN Drill Bit - Carbide 3.5 (89 mm) carbide tipped, part.no. T40-0276 2.38 kg pc. stock TITAN Drill Bit - Cross Cut 90, (90 mm Ø), mixed soil with obstacles part.no. T40-0256 1.05 kg pc. stock TITAN Drill Bit - Cross Cut 115 (115 mm Ø), for soft soils, sand and cobbles and soft rock, with top and radial flushingholes, screw-on type part.no. T40-0296 2 kg pc. stock TITAN Drill Bit - Aggressive Soft Soil Bit, 100 mm Ø, for clay and mudstone, screw-on type part.no. T40-0253 0.83 kg pc. TITAN Drill Bit - Carbide cross cut 3-step, cuts through several hard layers, screw-on type part.no. P40-004 1.2 kg pc. Piling Cone, (90 mm Ø), for displaceable soils, clay or high water table, screw-on type part.no. T40-0264 2.06 kg pc. Centralizer 88 mm Ø, for 20 mm grout cover, cast iron black part.no. T40-0242 0.45 kg pc. stock Geotextile Fixing Plate, 285 mm Ø for CTS/TITAN 30/11 and 40/16 galv. part.no. P30-005 6.00 kg pc. 14

CTS CON-TECH SYSTEMS LTD CTS/TITAN 40/16 & 40/20 Bore Hole Stopper, material PE, to seal bore holes, up to 80 mm Ø, screw-on type, 100 mm long, part.no. P40-010 0.1 kg pc. Eye bolt, hole 40/30 mm, SWL 300 kn galvanized part.no. T40-0303 1.90 kg pc. Load Indicator for 40/16, to indicate loads of 200, 300 and 400 kn, retracts by a total of 40 mm, LOBA approved galvanized part.no. P40-012 0.59 kg pc. Flushing Head 40/16 for hexagon S 22 (7/8"), for left hand rotary and percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 1/2") male for grout hose, length 368 mm, to be used in connection with holder only, incl. transport box, part.no. P40-013 6.40 kg pc. Complete set of spare seals for S 22 flushing heads (2 pieces, 40 x 50 x 7 mm) part.no. TAC-0018 set Holder, spring action, for Flushing Head 40/16-S22, bolts on to the mast of the drill rig, part.no. TAC-0019 7.20 kg pc. Flushing Head 40/16 available for R32*(1-1/4"), R38*(1-1/2"), T38*, T45*, for left hand rotary and percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8 " (BSP 3/4") male for grout hose, with lubrication nipple, length 265 mm, to be used in connection with holder only, incl. transport box, part.no. T40-0279/..0244/..0243/..024513.30 kg pc. stock Complete set of spare seals for R 32 - T 45 flushing heads (2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6.3 mm) part.no. TAC-0005 set stock Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*, to be fixed on to the mast of the drill rig fixing position: hammer fully extended and spring released part.no. TAC-0020 5.90 kg pc. stock Flushing Head R 55 (2-1/4"), for left hand rotary and percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP R 3/4") male for grout hose, with lubrication nipple, length 365 mm, to be used in connection with holder only, incl. transport box part.no. T40-0295 34.20 kg pc. Complete set of spare seals for R 55 flushing heads ( 2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9.7 mm) part.no. TAC-0021 set Holder for Flushing Head R55, C 64, RT 70, C90 and H112 for all drill rigs part.no. TAC-0015 2.45 kg pc. *please specify when ordering Drill Connectors or flushing heads for other threads on request. 15

CON-TECH SYSTEMS LTD CTS/TITAN 40/16 & 40/20 CTS Grouting Connector, for high pressure grout-hose DN 20 thread Rd32 x 1/8 male, with handle and lubrication nipple galvanized part no. T40-0241 1.5 kg pc. CTS Grout Swivel - T38m/T38m for left hand rotary/percussion drilling and for flushing with water, grout or air 1 NPT male for grout hose connection part.no. TAC-0003 6.75 kg pc. stock CTS Adaptor Couplers - T38/TITAN40 part.no. MIC-0034 2.95 kg pc. stock 16

CTS CON-TECH SYSTEMS LTD CTS/TITAN 52/26 CTS/TITAN Injection Bore Hollow Bar System 52/26 CTS/TITAN Injection Hollow Bar 52/26, design load (60% GUTS) 557 kn, left hand threaded, right-hand threaded available on special order in 3 m lengths. black left hand thread part.no. T52-0160 9.83 kg/m pc. stock CTS/TITAN 52/26 Injection Anchors are also available in other lengths. Please ask us for pricing. Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors and are also available. Please ask us for pricing. Spherical Collar Nut SW 80 x 70, max. inclination ± 10 of washer plate, black part.no. T52-0162 2.20 kg pc. stock Coupling 70 mm Ø x 160 mm, with center-stop, hardened, with 2 rubber seals, black part.no. T52-0161 2.42 kg pc. stock Bayonet Coupler 105 Ø x 325 mm, recoverable part.no. P52-006 11.70 kg pc. Adapter for Bayonet Coupler, recoverable part.no. P52-007 Bearing Plate, 220 x 220 x 35 mm for Anchorpiles, hole Ø 65 mm black part.no. T52-0157 13.1 kg pc. Steel Ball, 100 mm Ø, black, 54 mm bore in the steel ball, max. inclination 36 part.no. P52-001 3.25 kg pc. Plate for Steel Ball 300 x 200 x 35 mm, hole Ø 93 without ball, black part.no. P52-001a 14.4 kg pc. Wedge Disc, 12, allows max. 0 x 24, black, part.no. T52-0152 5.00 kg pc. stock Drill Bits TITAN Drill Bit - Cross Cut 115, (115 mm Ø), for soft soils, sand and cobbles and soft rock with top and radial flushing holes, screw-on type part.no. T52-0147 2.51 kg pc. stock CTS/TITAN Drill Bit - Carbide 3.5 (89 mm) carbide tipped part.no. T52-0150 2.04 kg pc. stock TITAN Drill Bit - Clay bit 130 mm Ø, screw-on type part.no. T52-0165 2.37 kg pc. stock TITAN Drill Bit - HPI-Clay bit 130 mm Ø, for jet grouting up to 200 bar with 2 nozzles, 2,3 mm Ø, part.no. P52-003 2.40 kg pc. stock TITAN Drill Bit - Button Type 115, (115 mm Ø), for hard or high quarzite rock carbide tipped screw-on type part.no. P52-004 3.3 kg pc. 17

CON-TECH SYSTEMS LTD CTS/TITAN 52/26 CTS Centralizer 112 mm Ø, cast iron black part.no. T52-0140 1.2 kg pc. stock Flushing Head 52/26 available for R32*(1-1/4"), R38*(1-1/2"), T38*, T45*, for rotary/percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 3/4") male for grout hose, with lubrication nipple, length 365 mm, to be used in connection with holder only, incl. transport box, part.no. T52-0172/..0142/..0164/..0158/ 18.80 kg pc. stock complete set of spare seals for flushing heads R 32 - T 45 (2 seals 63 x 78 x 11,4 mm plus 2 guide rings 63 x 68 x 6,3 mm) part.no. TAC-0005 set stock Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*, to be fixed on to the mast of the drill rig fixing position: hammer fully extended and spring released part.no. TAC-0020 5.90 kg pc. stock Flushing Head R 55 ( 2-1/4"), for rotary/percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" or BSP 3/4" and 1-1/2" female for grout hose, with lubrication nipple, length 365 mm, to be used in connection with holder only, incl. transport box part.no. T5R-0050 34.30 kg pc. complete set of spare seals for R 55 flushing head (2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9,7 mm) part.no. TAC-0021 set Holder for Flushing Head R55, C 64, RT 70, C90 and H112 for all drill rigs part.no. TAC-0015 2.45 kg pc. stock Grouting Connector for 52/26, for high pressure grout-hose DN 20, thread Rd 32 x 1/8" male, with handle and lubrication nipple, galvanized part.no. P52-005 1.80 kg pc. 18

CTS CON-TECH SYSTEMS LTD CTS/TITAN 73/56, 73/53 & 73/45 CTS/TITAN Injection Bore Hollow Bar System 73 / 56 CTS/TITAN Injection Hollow Bar 73/56, design load (60% GUTS) 656 kn continuously right-hand threaded in 6.25 m lengths black, part.no. T73-0172 10.75 kg/m pc. stock CTS/TITAN Injection Bore Hollow Bar System 73 / 53 CTS/TITAN Injection Hollow Bar 73/53, design load (60% GUTS) 696 kn continuously right-hand threaded in 3 m lengths black, part.no. T73-0154 12.24 kg/m pc. stock CTS/TITAN Injection Bore Hollow Bar System 73 / 45 CTS/TITAN Injection Hollow Bar 73/45, design load (60% GUTS) 978 kn continuously right-hand threaded in 3 m lengths black, part.no. T73-0173 17.8 kg/m pc. stock CTS/TITAN Injection Bore Hollow Bar System 73 / 35 CTS/TITAN Injection Hollow Bar 73/35, design load (60% GUTS) 1188 kn continuously right-hand threaded in 3 m lengths black, part.no. T73-0173 17.8 kg/m pc. stock CTS/TITAN 73 Injection Anchors are also available in other lengths. Please ask us for pricing. Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors and are also available. Please ask us for pricing. Spherical Collar Nut SW 95 x 70 black, part.no. T73-0163 2.22 kg pc. stock Coupling 89 Ø x 225 mm, St. 52-3, with internal rubber seal, black, part.no. T73-0161 3.72 kg pc. stock Bayonet Coupler 105 Ø x 325 mm, recoverable part.no. P73-001 11.70 kg pc. Bearing Plate, 250 x 250 x 40 mm for Anchorpiles, hole Ø 80 mm, max. inclination ± 6, black part.no. T73-0166 18.00 kg pc. Wedge Disc, 12 for 73/53, 200 mm, allows max. 2 x 12, black, part.no. T73-0162 5.97 kg pc. stock Centralizer 130 mm Ø, cast iron, black part.no. T73-0148 1.39 kg pc. stock 19

CON-TECH SYSTEMS LTD CTS/TITAN 73/56, 73/53 & 73/45 CTS TITAN Drill Bit - Cross Cut, 130 mm Ø, for mixed soil with obstacles, screw-on type part.no. T73-0157 3.12 kg pc. stock TITAN Drill Bit - Cross Cut, 175 mm Ø screw-on type part.no. T73-0169 8.22 kg pc. stock TITAN Drill Bit - Clay Bit 200 mm Ø, screw-on type part.no. P73-004 6.10 kg pc. stock TITAN Drill-Bit - Button Type 130, (130 mm Ø) with carbide buttons, screw-on type part no. T73-0158 5.5 kg pc. stock TITAN Drill Bit - Carbide Cross Cut 3 Step 130 (130 mm Ø) drill bit for directional stability, cuts through several hard layers of soil/rock part no. P73-0006 5.8 kg pc. Flushing Head R 55 (2¼"), for right hand rotary and percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 3/4") male for grout hose, with lubrication nipple, length 365 mm, to be used in connection with holder only, incl. transport box, part.no. T73-0149 32.10 kg pc. stock complete set of spare seals for R 55 flushing head (2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9.7 mm) part.no. TAC-0021 set stock Rotary Flushing Head R 55 (2 1/4"), self contained, length 405 mm, no holder required, 120 mm wrench required, incl. transport box, part.no. T73-0153 43.70 kg pc. Flushing Head H 112, for right hand rotary and percussive drilling, for flushing with water, grout or air, thread BSP 2" male for grout hose, with lubrication nipple, length 300 mm, to be used in connection with holder only, incl. transport box, part.no. T73-0151 53.20 kg pc. complete set of spare seals for flushing head H 112 (2 seals 160 x 185 x 16 mm plus 2 guide rings 160 x 165 x 14.8 mm) part.no. TAC-0022 pc. Holder for Flushing Head R55, C 64, RT 70, C90 and H112 for all drill rigs part.no. TAC-0015 2.45 kg pc. stock 20

CTS CON-TECH SYSTEMS LTD CTS/TITAN 103/78 & 103/51 CTS/TITAN Injection Bore Hollow Bar System 103/78 CTS/TITAN Injection Hollow Bar 103/78, design load (60% GUTS) 1369 kn, continuously right-hand threaded in 3 m lengths. black, part.no. T03-0106 24.50 kg/m pc. stock CTS/TITAN Injection Bore Hollow Bar System 103/51 CTS/TITAN Injection Hollow Bar 103/51, design load (60% GUTS) 2076 kn, continuously right-hand threaded in 3 m. lengths. black, part.no. T03-0120 43.40 kg/m pc. stock CTS/TITAN 103/78 & 103/51 Injection Anchors are also available in other lengths. Please ask us for pricing. Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors and are also available. Please ask us for pricing. Spherical Collar Nut SW 125 x 80, black, part.no. T03-0110 3.42 kg pc. stock Coupling Nut 123 mm Ø x 255 mm, with internal rubber seal, black 2282 KN part.no. T03-0109 7.47 kg pc. stock Coupling Nut 132 mm Ø x 290 mm, with internal rubber seal, black 3460 KN part.no. T03-0121 12.6 kg pc. Bayonet Coupler 135 Ø x 384 mm, recoverable part.no. P03-002 19.00 kg pc. Bearing Plate 300 x 300 x 50 mm, black, part.no. T03-0113 32.60 kg pc. Drill Bits TITAN Drill Bit - Cross Cut, 175 mm Ø, for mixed soil with obstacles, screw-on type part.no. T03-0108 5.70 kg pc. stock TITAN Drill Bit - Clay Bit 220 mm Ø, part.no. P03-002 12.6 kg pc. stock TITAN Drill Bit - Clay Bit 280 mm Ø part no. T03-0122 13.9 kg pc. stock TITAN Drill Bit - Button Type 175, (175 mm Ø), with carbide buttons, screw-on type part.no. T03-0119 10.2 kg pc. stock Centralizer, 165 mm Ø, cast iron, black, part.no. T03-0101 2.94 kg pc. stock 21

CON-TECH SYSTEMS LTD CTS/TITAN 103/78 & 103/51 CTS Flushing Head R 55 (2¼"), for right hand rotary and percussive drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" or BSP 3/4" and 1-1/2" female, for grout hose, with lubrication nipple, length 365 mm, to be used in connection with holder only, incl. transport box, part.no. T03-0102 40.00 kg pc. stock complete set of spare seals for R 55 flushing head (2 seals 100 x 120 x 12 mm plus 2 guide rings 100 x 105 x 9.7 mm) part.no. TAC-0021 set stock Flushing Head, H 112 for right hand rotary and percussive drilling, for flushing with water, grout or air, thread BSP 2" male, for grout hose, with lubrication nipple, length 300 mm, to be used in connection with holder only, incl. transport box part.no. T03-0104 48.40 kg pc. stock complete set of spare seals for H 112 flushing head (2 seals 160 x 185 x 16 mm plus 2 guide rings 160 x 165 x 14.8 mm) part.no. TAC-0022 set stock Holder for Flushing Head R55, C 64, RT 70, C90 and H112 for all drill rigs part.no. TAC-0015 2.45 kg pc. stock 22

CTS CON-TECH SYSTEMS LTD CTS/TITAN 130/60 CTS/TITAN Injection Bore Hollow Bar System 130/60 CTS/TITAN Injection Hollow Bar 130/60, design load (60% GUTS) 4764 kn, continuously right-hand threaded in 3 m lengths. black, part.no. T13-0001 79 kg/m pc. CTS/TITAN 130/60 Injection Anchors are also available in other lengths. Please ask us for pricing. Galvanized, Metallized or EPOXY Coated CTS/TITAN Injection Anchors and are also available. Please ask us for pricing. Spherical Collar Nut black, part.no. T13-0003 pc. Coupling Nut with internal rubber seal, black black part.no. T13-0002 pc. TITAN Drill Bit - Carbide Button Bit 220 mm Ø, screw-on type part.no. T13-0004 pc. 23

CON-TECH SYSTEMS LTD CTS/TITAN CTS CTS/TITAN Hollow Bar Technical Data 3 Drill Bit Selection Chart 5 CTS/TITAN R32 7 7 CTS/TITAN T30/11 & T30/16 9 Injection Hollow Bars 9 9 CTS/TITAN T40/16 & T40/20 13 Injection Hollow Bars 13 13 CTS/TITAN T52/26 17 Injection Hollow Bars 17 17 CTS/TITAN T73/56 T73/53 & T73/45 19 Injection Hollow Bars 19 19 CTS/TITAN T103/78 & T103/51 21 Injection Hollow Bars 21 21 CTS/TITAN T130/60 23 Injection Hollow Bars 23 23 24