TECALEMIT FLEXIBLES SWAGE FITTINGS CATALOGUE CATALOGUE N 777-89 Swage Fittings Catalogue
Swage Fittings Catalogue - 1 Tenir au Temps Y.Tromelin & S.Bergsen Hannover 2005 TECALEMIT FLEXIBLES, renowned by name and for its patents, driven and accompanied by professionals, guarantees security in supplies of flexible hose and fittings. TECALEMIT FLEXIBLES offers 3 divisions : SEL TECALEMIT SEL Elastomer hoses RCMH swaged industrial hoses FLEXIBLES TECALEMIT Hydraulic hose and fittings Hose assemblies TUBES TECALEMIT Flexible pneumatic tubes Preformed and multitubes
2 - Swage Fittings Catalogue E.Piquerez J.Christe History Emile PIQUEREZ invented his famous pressurised greasing system, with a simple hook-on connection, and gave it the name of TECHLA. Joseph CHRISTE, on his side, made an agreement with the ALEMIT Company in the United States of America, by which the PIQUEREZ patents were passed on to this Company for the Americas, in exchange for their own greasing patents with bayonet connections, for Europe. This is the starting point of the TECALEMIT Company, whose offices, stores, workshops and service-station were set up, by the two founders, 18 rue Brunel in Paris in may 1922. The name TECALEMIT, emanating from TECHLA and ALEMITE, was to remind users of pressurised greasing systems that both makes could be found at TECALEMIT.. Car owners came by the hordes to change their grease nipples in 15 to 20 minutes at a cost of under 100 francs. But TECALEMIT did not stop there. From the grease pump with a flexible hose and hook-on connector, they progressed to the push-type pump with rigid pipe and articulated connector, then to Lub and Zerk greasings, and finally to the even more elaborate system which now equips almost all vehicles and machines in the world : the hydraulic system.
Swage Fittings Catalogue - 3 In 1946 came the TECALEMIT rubber hoses with swaged fittings, then in 1950, the TECALEMIT-AEROQUIP flexible hoses with reusable fittings and finally in 1961, the tubes and hoses in superpolyamide and polyurethane, which were produced in the factory in Orly. In 1972, a factory, specially dedicated to these productions was built in Blois, where the activities of TECALEMIT FLEXIBLES, name registered in 1980, were located avenue de Chateaudun. In January 2006, all the company s activities, with the exception of aerospace, were transferred to Pont l Abbé, route de Combrit. The programme now includes a full range of hose, reusable and swaged fittings to equip hydraulic controls to which can be added the pneumatic tubes manufactured under the names of Manuril, Manulan et Maluform. All these products, originally intended for the automotive field, have been adopted by the Aerospace Industry, the Railways, the Navy, Public Building and Works and General Industries.
4 - Swage Fittings Catalogue Summary S SD SC AQ TECHNICAL GUIDE 1 - TYPES OF FITTINGS AND FERRULES 1-1 - TYPES OF FITTINGS AND FERRULES 1-1 - 1 - Ferrules for textile-reinforced hose 1-1 - 2 - Ferrules for steel-reinforced hose with external skiving 1-1 - 3 - Ferrules for steel-reinforced hose without external skiving 1-1 - 4 - Ferrules for steel-reinforced hose with external and internal skiving 1-2 - SELECTION OF FERRULES ACCORDING TO HOSE TYPE 1-3 - USE OF DIFFERENT INSERTS 1-3 - 1 - Insert type S : for low, medium and high s 1-3 - 2 - Insert type SD : for very high s 1-3 - 3 - Insert type SC : for very high s 1-3 - 4 - Insert type AQ : for very high s 2 - PART NUMBERING SYSTEM 3 - TYPES OF CONNECTIONS 3-1 - METRIC 3-1 - 1 - METRIC type DIN 24 according to ISO 151-2 3-1 - 2 - METRIC type French gaz series 24 cone 3-1 - 3 - METRIC type DIN 60 cone 3-2 - B.S.P 3-2 - 1 - BSP type 60 cone 3-2 - 2 - BSP type 60 cone with O -ring 3-2 - 3 - BSP type flat seat 3-2 - 4 - BSP type taper thread 3-3 - J.I.C 3-4 - FLANGE 3-5 - O.R.F.S 3-6 - N.P.T 3-7 - S.A.E 3-7 - 1 - SAE type 90 cone according to SAE J516 3-7 - 2 - SAE type flat seat according to SAE J516 3-8 - MISCELLANEOUS 3-8 - 1 - BANJO type 3-8 - 2 - JIS type 3-8 - 3 - STAND-PIPE type 4 - TORQUE SETTINGS (N/M) 5 - THREAD IDENTIFICATION Page 6 6 6 6 7 7 8 9 9 10 10 11 14 14 14 16 18 20 20 22 24 25 26 28 30 32 34 34 36 37 37 38 40 41 42 Parc d Activités de Kermaria, 290 Pont l Abbé FRANCE Tél : (33) 02 98 82 48 48 / Fax : (33) 02 98 82 48 49 / e-mail : contact@tecalemitflexibles.com "All information given in this catalogue is for guidance only. We cannot be held liable for any errors or omissions. "
Swage Fittings Catalogue - 5 S SD SC AQ Summary CATALOGUE OF PRODUCTS Page 6 - FERRULES 7 - INSERTS METRIC Metric light series Metric heavy series Metric French gaz series DIN 60 cone DIN 24 /60 cone S SD SC SD SC S 44 50 50 50 52 56 58 61 B.S.P BSP 60 cone BSP flat seat BSP taper S SD SD SC SC 62 62 71 72 J.I.C S SD SC 73 FLANGE 3000 psi SAE Flange 6000 psi SAE Flange SUPERCAT Flange Flange accessories S SD SC 81 81 85 89 92 O.R.F.S S SD SC 94 N.P.T S SD SC 98 S.A.E S 100 MISCELLANEOUS Banjo metric Banjo bolt metric Banjo BSP Banjo bolt BSP Stand-Pipe metric Stand-Pipe French gaz J.I.S JIS flange Stand-Pipe for HP washer hose Female metric swivel for HP washer hose Double connector Farm valve metric male AQ type ferrules and fittings S AQ 102 102 102 103 103 104 107 108 109 110 110 110 110 111 Parc d Activités de Kermaria, 290 Pont l Abbé FRANCE Tél : (33) 02 98 82 48 48 / Fax : (33) 02 98 82 48 49 / e-mail : contact@tecalemitflexibles.com "All information given in this catalogue is for guidance only. We cannot be held liable for any errors or omissions. "
TECHNICAL GUIDE 6 - Swage Fittings Catalogue Technical guide 1 TYPES OF FITTINGS AND FERRULES 1 1 Description of swage ferrules 1 1 1 Ferrules for textile-reinforced hose At the forward end of the ferrule, the recess G is designed to lock onto the collar of the hydraulic insert during swaging : the insert and the ferrule therefore become interdependent. Moreover, the back-stop B is designed to facilitate mounting and enhance reliability of the hose which cannot hinder the positioning of the collar during swaging. Barbs (detail C) are not very pronounced, so as not to damage either the textile structure of the hydraulic hose or its outer cover which is not skived before swaging. Example : Ferrules 5030 Type of ferrule Recess G Back-stop B Hose Dash Size C Detail C Ech 4 1 1 2 Ferrules for steel-reinforced hoses with external skiving At the forward end of the ferrule, the recess G is designed to lock onto the collar of the hydraulic insert during swaging : the insert and the ferrule therefore become interdependent. Moreover, the back-stop B is designed to facilitate mounting and enhance reliability of the hose which cannot hinder the positioning of the collar during swaging. The barbs (detail C), of a fir-tree shape, are pronounced without being sharp. These barbs bite into the steel braid or spiral of the hose which has been externally skived beforehand. Swaging is considered correct when the internal bore of the hose insert has collapsed by several tenths of a millimeter according to recommendations by TECALEMIT FLEXIBLES. Example : Ferrules 5020 Recess G C Back-stop B Detail C Ech 3
Swage Fittings Catalogue - 7 Technical guide TECHNICAL GUIDE 1 1 3 Ferrules for steel-reinforced hose without external skiving At the forward end of the ferrule, the recess G is designed to lock onto the collar of the hydraulic insert during swaging : the insert and the ferrule therefore become interdependent. Moreover, the back-stop B is designed to facilitate mounting and enhance reliability of the hose which cannot hinder the positioning of the collar during swaging. The internal barbs (Detail C) are very pronounced and sharp. During swaging, these barbs bite through the rubber outer cover and into the steel braid or spiral of the hose. Swaging is correct when the internal bore of the hose insert has collapsed by several tenths of a millimeter accroding to recommendations by TECALEMIT FLEXIBLES. Example : Ferrules 5023 Recess G Back-stop B C Detail C Ech 4 1 1 4 Ferrules for steel-reinforced hose with internal and external skiving At the forward part of the ferrule, the heel T is designed to lock into the collar of the hydraulic insert during swaging in order to obtain an interdependent assembly. The boss (detail D) is destined to be swaged directly onto the high-tensile steel spirals, which have previously been skived on the inside and outside, locking them into a female recess on the tail of the hydraulic insert. Resistance is of high quality, assembly being metal to metal. The barbs (detail D) are designed to ensure sealing of the inner tube through external compression on the metal spirals. The back inner shape (detail E) of the ferrule is designed to ensure sealing between the ferrule and the outer rubber cover, in such a way as to prevent any external agent from corroding the metal reinforcement of the hose. Swaging is considered correct when the internal bore of the hose insert has collapsed by several tenths of a millimeter according to recommendations by TECALEMIT FLEXIBLES. Example : Ferrules 5692 Heel T C D Detail C Ech 3 Detail D Ech 3 E Detail E Ech 3
TECHNICAL GUIDE 8 - Swage Fittings Catalogue Technical guide 1 2 Selection of ferrules according to hose type Dia Int (inch) 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 2 Hose Dia Int (mm) 4,8 6,4 7,9 9,5,7 15,9 19,0 25,4 31,8 38,1 50,8 Type Dash 3 4 5 6 8 10 16 20 24 32 Ferrule Part N for insert type S T 110 EN 853 1ST - R1A 501003 501004 501005 501006 501008 501010 5010 501016 501020 501024 501032 T 111 501303 501304 501305 501306 501308 501310 5013 501316 501320 501324 501332 EN 853 1SN - R1T 502304 502305 T 1 EN 857 1SC 501404 501405 501406 501408 501410 5014 501416 T 210 EN 853 2ST - R2A 501003 501004 501005 501006 501008 501010 5010 501016 502020 502024 502032 T 211 EN 853 2SN - R2T 502303 502304 502305 502306 502308 502310 5023 502316 502320 502324 502332 T 221 EN 857 2SC 501304 501305 501306 501308 501310 5013 501316 T 911 EN 856 4SP 509104 509106 509108 509110 5091 509116 5090 5094 509132 T 9 EN 856 4SH 5091 509116 509220 509224 509232 T331 SAE 100 R 3 503004 503005 503006 503008 503010 5030 503016 T 610 - T611 EN 854 R6 507003 507004 507005 507006 507008 507010 5070 507016 T710 EN 855 R7 507003 507004 507005 507006 507008 507010 5070 507016 T711 EN 855 R8 507003 507004 507005 507006 507008 507010 5070 507016 TTA 507003 507104 507005 507006 507008 TTK 507003 507104 507005 507006 507008 Ferrule Part N for insert type SD T9 EN 856 4SH 5692 569216 569320 569324 569332 T1310 EN 856 R13 5692 569216 569320 569324 569332 T915 EN 856 R15 T 911 EN 856 4SP T9 EN 856 4SH T1310 EN 856 R13 T915 EN 856 R15 T961 AQUABLAST T962 AQUABLAST T1362 AQUABLAST Ferrule Part N for insert type SC Ferrule Part N for insert type AQ 569704 509606 509608 5096 509616 509606 509608 5096 569806 569808 5698 569816 5692 569216 569320 569324 569332 5093 509316 509620 509624 509632 5094 509416 5093 509316 509320 509324 509332 5094 509416 509420 509424 509432 5093 509316 509620 509624 509632 5094 509416 5093 509316 509620 509624 5094 509416
Swage Fittings Catalogue - 9 Technical guide TECHNICAL GUIDE 1 3 Use of different inserts The TECALEMIT FLEXIBLES range of swaged hose inserts is comprised of 4 different types : Each type is related to specific applications. - Type S : low, medium and high - Type SD : high and very high, with internal and external skive - Type SC : high and very high, without internal skiving - Type AQ : very high for AQUABLAST hose The different types can be identified by their tail profile. Type S Type SD Type SC 1 3 1 Insert type S : for low, medium and high Type AQ These inserts are the most commonly used. They have a european style tail where the barbs have a fir-tree layout. The latch area is simple, being comprised of a recess into which the forward part of the ferrule locks during swaging. Types of TECALEMIT FLEXIBLES hydraulic hose concerned (see catalogue 777-86) : - textile-reinforced hose : T331, T610, T611, T622, T623 - metal braided hose : T110, T111, T116, T117, VKI, T1, T210, T211, T221 - metal spiral hose : T911, T9 - thermoplastic textile-reinforced hose : T710, T810, TTA, TTK - thermoplastic metal-reinforced hose : T711 Use ferrules in chapter type S according to hose (details page 8). Type S without skiving Type S with external skiving
TECHNICAL GUIDE 10 - Swage Fittings Catalogue Technical guide 1 3 2 Insert type SD : for very high s This range of fittings is exclusively designed for very high applications as its assembly is quite complex, requiring both internal and external skiving. The barbed tail is long with a profile commonly called interlock, the barbs have a fir-tree layout with a bulbous forward part designed to maintain the steel layers of the hose s reinforcing structure. The latch area is double : at the forward part of the ferrule, a recess into which the collar of the insert will lock and a bulbous ring inside the ferrule which compresses the reinforcing metal spirals into a corresponding depression on the insert. Types of TECALEMIT FLEXIBLES hydraulic hose concerned (see catalogue 777-86) : - 4 or 6 steel spiral reinforced hose : T9, T915, T1310 Use ferrules in chapter type SD according to hose (detail page 8). Type SD with internal and external skive 1 3 3 Insert type SC : for very high s This range of inserts does not require internal skiving for very high hoses. External skiving is only required on diameters 1 1/4, 1 1/2 and 2 (32mm, 38mm, 50mm) on hose types T911, T915, T1310. For hose type T9, no internal skiving is required whatever the diameter. The tail is long with very pronounced barbs. The latch area is very simple, comprised of a groove into which the forward part of the ferrule will lock. Type of TECALEMIT FLEXIBLES hydraulic hose concerned (see catalogue 777-86) : - 4 or 6 steel spiral reinforced hose : T911, T9, T915, T1310 Use SC type ferrules according to hose (detail page 8). Type SC without external skiving Type SC with external skiving
Swage Fittings Catalogue - 11 Technical guide TECHNICAL GUIDE 1 3 4 Insert type AQ : for very high s These double-skive inserts are intended for TECALEMIT FLEXIBLES hoses designed for industrial cleaning by water blasting at very high s. The barbed tail is long with a profile commonly called interlock, the barbs have a fir-tree layout with a bulbous forward part designed to maintain the steel layers of the hose s reinforcing structure. The latch area is double : at the forward part of the ferrule, a recess into which the collar of the insert will lock and a bulbous ring inside the ferrule which compresses the reinforcing metal spirals into a corresponding depression on the insert. Types of TECALEMIT FLEXIBLES hoses concerned (see catalogue 777-86) : - 4 or 6 steel spiral reinforced hose : T961, T962, T1362 Use ferrules in chapter type SD according to hose (detail page 8). Type AQ with internal and external skiving
TECHNICAL GUIDE - Swage Fittings Catalogue Technical guide 2 PART NUMBERING SYSTEM Example : S 471 08 Straight S type fitting, insert family 47 (female BSP), dash-size (3/4 ) for hose dash-size 08 (1/2 ). S SD SC AQ ORIENTATION 1 = straight 2 = 45 swept 3 = 90 swept TYPE OF INSERT Inserts type S Inserts type SD Inserts type SC inserts type AQ HOSE DASH-SIZE Dash Hose ID inch mm 3 3/16 4,8 4 1/4 6,3 5 5/16 7,9 6 3/8 9,5 8 1/2,7 10 5/8 15,9 3/4 19,1 16 1 25,4 20 1 1/4 31,8 24 1 1/2 38,1 32 2 50,8 S 47 1 08 Inserts SD S SC INSERT FAMILY (type of thread) Family Type of thread 11 J.I.C 13 14 18 21 22 28 31 32 33 42 45 46 47 48 62 63 64 71 74 76 77 78 81 86 88 49 50 51 52 59 70 79 89 92 94 97 N.P.T S.A.E S.A.E O.R.F.S J.I.C S.A.E O.R.F.S B.S.P B.S.P B.S.P B.S.P B.S.P B.S.P B.S.P B.S.P METRIC METRIC METRIC METRIC METRIC METRIC METRIC METRIC FLANGE FLANGE FLANGE JIS-BSP female swivel HP washer stand-pipe STAND-PIPE STAND-PIPE DOUBLE CONNECTOR HP washer female swivel JIS-METRIC female swivel JIS FLANGE collar BANJO for metric bolt BANJO for BSP bolt FARM-VALVE male Dash-size of insert (thread or tube size (see right-hand page) male with 74 cone male with 60 cone male with O-ring male with 90 cone male with O-ring face seal female with 74 cone female swivel with 90 cone female swivel with flat seat male parallel with seat and 60 cone male taper with 74 cone male parallel with flat seat female swivel with flat seat female swivel 90 compact female swivel with 60 cone slip on nut female swivel with 60 cone female swivel with 60 cone and O-ring male 24 cone light (DKOL) male 24 cone heavy (DKOS) male 24 cone French gaz female swivel 60 cone female swivel 24 cone French gaz female swivel 24 cone light female swivel 24 cone heavy female swivel 24 /60 cone 3000 psi collar 6000 psi collar SUPERCAT collar
Swage Fittings Catalogue - 13 Technical guide TECHNICAL GUIDE Dash size 2 4 6 7 METRIC thread MX1,5 METRIC DIN thread 8 9 M14X1,5 10 13 M16X1,5 M18X1,5 M20X1,5 M10X1 MX1,5 14 M22X1,5 M14X1,5 15 16 M22X1,5 M16X1,5 17 M24X1,5 18 19 M26X1,5 M18X1,5 20 21 M30X2 M30X1,5 M20X1,5 22 24 25 26 M30X2 M36X2 M22X1,5 M24X1,5 M26X1,5 27 M36X1,5 28 30 M36X2 M42X2 M30X1,5 32 33 35 38 M45X1,5 M45X2 M52X2 M38X1,5 40 42 M52X2 45 M45X1,5 Dash METRIC B.S.P BANJO BANJO size thread thread 2 1/8-28 4 1/4-19 6 3/8-19 7 8 1/2-14 9 10 M10X1 5/8-14 3/4-14 13 MX1,5 14 M14X1,5 15 16 M16X1,5 1-11 17 18 M18X1,5 19 20 M20X1,5 21 22 M22X1,5 24 25 26 M26X1,5 27 28 30 M30X1,5 32 33 35 36 38 40 42 INSERT DASH-SIZE (thread or tube diameter) B.S.P thread 1/8-28 1/4-19 3/8-19 1/2-14 5/8-14 3/4-14 1-11 1 1/4-11 1 1/2-11 2-11 METRIC STAND PIPE dia. J.I.C thread 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1 1/16-1 3/16-1 5/16-1 5/8-1 7/8-2 1/2 - J.I.S B.S.P thread 1/4 6 3/8 8 1/2 10 3/4 14 15 16 1 18 20 1 1/4 22 25 28 30 35 38 42 1 1/2 FLANGE collar 1/2 5/8 3/4 1 1 1/4 1 1/2 2 2 1/2 O.R.F.S thread 9/16-18 11/16-16 13/16-16 1-14 1 3/16-1 7/16-1 11/16-2 - J.I.S METRIC thread M14X1,5 M16X1,5 M18X1,5 M22X1,5 M24X1,5 M30X1,5 M33X1,5 M36X1,5 M42X1,5 N.P.T thread 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11,5 1 1/4-11,5 1 1/2-11,5 2-11,5 HP WASHER thread M22X1,5 S.A.E thread 7/16-20 1/2-20 9/16-18 5/8-18 3/4-16 7/8-14 1 1/16-1 5/16 - FARM VALVE thread M18X1,5
TECHNICAL GUIDE 14 - Swage Fittings Catalogue Technical guide 3 TYPES OF CONNECTIONS Equipment using the transfer of power through hydraulic oil are designed and manufactured throughout the world and, consequently, the hydraulic connections are made according to various standards, found even in the same country. The most common standards are described hereafter, with indications of the norms to which they belong. 3 1 METRIC type 3 1 1 METRIC type 24 cone according to ISO 151-2 METRIC 24 cone sealing arrangement Concerns light (DKOL) and heavy (DKOS) series metric fittings. Sealing : O-ring on male 24 cone inserted into 24 female cone Connection : parallel metric thread, profile according to NFE-03-001 (identical to ISO 68-1), whose outer diameter is expressed in millimeters. The profile of this thread is an equilateral triangle. Metric threads are designated by the letter M, followed by their external diameter and pitch. Ex. : Mx1.5 Sealing by O-ring 24 METRIC thread type 24 cone P DT DE DA Light series Circuit dia. 1/4 5/16 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 2 Dash 4 5 6 8 10 16 20 24 32 Thread Size X1,50 14X1,50 16X1,50 18X1,50 22X1,50 26X1,50 30X2,0 36X2,0 45X2,0 52X2,0 L Male Thread Outer Diameter (DE)(mm) 14 16 18 22 26 30 36 45 52 Thread Pitch (mm) 1,50 1,50 1,50 1,50 1,50 1,50 2,0 2,0 2,0 2,0 Thread Length (L) (mm) 10 10 11 11 14 14 16 16 Tube Outer Diameter (DT) (mm) 6 8 10 15 18 22 28 35 42 Free Length (P) (mm) 2,5 2,5 3 3 5 4 4,5 6,5 8,5 8,5
Swage Fittings Catalogue - 15 Technical guide TECHNICAL GUIDE Heavy series Circuit Male Thread Thread Pitch Thread Size Outer Diameter dia. Dash (DE)(mm) (mm) 3/16 1/4 3 4 14 16 14 16 1,50 1,50 5/16 5 18 18 1,50 3/8 6 20 20 1,50 1/2 8 22 22 1,50 5/8 10 24 24 1,50 3/4 30 30 2,0 1 16 36 36 2,0 1 1/4 20 42 42 2,0 1 1/2 24 52 52 2,0 Sealing arrangements of both light and heavy series follow DIN 2353 Thread Length (L) (mm) 14 14 16 18 20 22 Tube Outer Diameter (DT) (mm) 6 8 10 14 16 20 25 30 38 Free Length (P) (mm) 3 3 3 5 5 5 6 7 7,5 8,5 Catalogue pages for METRIC 24 cone type Type Part N Description Page S 621 Male metric light series DKOL 24 cone 50 S 761 Female metric light series DKOL 24 cone 50 S 762 Female metric light series DKOL 24 cone 45 swept elbow 51 S S 763 Female metric light series DKOL 24 cone 90 swept elbow 51 S 631 Male metric heavy series DKOS 24 cone 52 S 771 Female metric heavy series DKOS 24 cone 45 52 S 772 Female metric heavy series DKOS 24 cone 45 swept elbow 53 S 773 Female metric heavy series DKOS 24 cone 90 swept elbow 53 SD SC AQ SD 631 SD 771 SD 772 SD 773 Male metric heavy series DKOS 24 cone 54 Female metric heavy series DKOS 24 cone 45 54 Female metric heavy series DKOS 24 cone 45 swept elbow 54 Female metric heavy series DKOS 24 cone 90 swept elbow 54 SC 631 Male metric heavy series DKOS 24 cone 55 SC 771 Female metric heavy series DKOS 24 cone 45 55 SC 772 Female metric heavy series DKOS 24 cone 45 swept elbow 55 SC 773 Female metric heavy series DKOS 24 cone 90 swept elbow 55 AQ 771 Female metric heavy series DKOS 24 cone 45 111
TECHNICAL GUIDE 16 - Swage Fittings Catalogue Technical guide 3 1 2 METRIC type French Gaz 24 cone METRIC French Gaz 24 cone sealing arrangement Sealing : 24 male cone into 24 female cone Connection : parallel metric thread, profile according to NFE-03-001 (identical to ISO 68-1), whose outer diameter is expressed in millimeters. The profile of this thread is an equilateral triangle. Metric threads are designated by the letter M, followed by their external diameter and pitch. Ex. : Mx1.5 Metal to metal sealing 24 METRIC French Gaz 24 cone type P DT DE DA L N Series Circuit Male Thread Thread Length Tube Outer Thread Pitch Free Length Thread Size Outer Diameter (L) Diameter (DT) dia. Dash (DE)(mm) (mm) (mm) (mm) (P) (mm) 1/8 3/16 2 3 M X1 M 14X1,5 14 1,0 1,5 6 8 2,5 2,5 1/4 5/16 4 5 M 16X1,5 M 16X1,5 16 16 1,5 1,5 10 3 3 3/8 7/16 6 7 M 20X1,5 M 22X1,5 20 22 1,5 1,5 14 15 5 5 1/2 5/8 8 10 M 24X1,5 M 27X1,5 24 27 1,5 1,5 14 16 18 5 4 3/4 7/8 14 M 27X1,5 M 30X1,5 27 30 1,5 1,5 14 14 20 22 6 4,5 1 1 1/4 16 20 M 33X1,5 M 36X1,5 33 36 1,5 1,5 14 14 25 28 6 6,5 1 1/2 1 3/4 24 28 M 39X1,5 M 45X1,5 39 45 1,5 1,5 14 16 30 35 7 7 2 2 1/2 32 40 M 48X1,5 M 52X1,5 48 52 1,5 1,5 16 16 38 40 8,5 6 3 48 M 54X2,0 54 2,0 16 45 8,5
Swage Fittings Catalogue - 17 Technical guide TECHNICAL GUIDE GAZ series Circuit Male Thread Thread Length Tube Outer Thread Pitch Free Length Thread Size Outer Diameter (L) Diameter (DT) dia. Dash (DE)(mm) (mm) (mm) (mm) (P) (mm) 1/4 1/2 4 8 20X1,5 24X1,5 20 24 1,5 1,5 14 13,2 16,8 5 5 3/4 1 16 30X1,5 36X1,5 30 36 1,5 1,5 16 16 21,2 26,8 4,5 7 1 1/4 1 1/2 20 24 45X1,5 52X1,5 45 52 1,5 1,5 16 16 33,5 42,2 7 6 2 32 58X2,0 58 2,0 16 48,5 8,5 Sealing arrangements of N and GAZ series are French versions of the above standards Catalogue pages for METRIC French Gaz 24 cone type S 641 S 741 S 742 S 743 Male METRIC French Gaz 24 cone Page 56 Female METRIC French Gaz 24 cone 45 swept Page 56 Female METRIC French Gaz 24 cone 45 swept elbow Page 56 Female METRIC French Gaz 24 cone 90 swept elbow Page 57
TECHNICAL GUIDE 18 - Swage Fittings Catalogue Technical guide 3 1 3 METRIC 60 cone type METRIC 60 cone sealing arrangement Sealing : 60 male cone into 60 female cone Connection : parallel metric thread, profile according to NFE-03-001 (identical to ISO 68-1), whose outer diameter is expressed in millimeters. The profile of this thread is an equilateral triangle. Metric threads are designated by the letter M, followed by their external diameter and pitch. Ex. : Mx1.5 Metal to metal sealing 60 METRIC 60 cone type P 30 DE DA L Circuit Male Thread Thread Length Tube Outer Thread Pitch Free Length Thread Size Outer Diameter (L) Diameter (DT) dia. Dash (DE)(mm) (mm) (mm) (mm) (P) (mm) 1/4 5/16 4 5 M X1,5 M 14X1,5 14 1,5 1,5 10 10 10,5,5 2,5 2,5 3/8 1/2 6 8 M 16X1,5 M 18X1,5 16 18 1,5 1,5 10 10 14,5 16,5 3 3 5/8 3/4 10 M 22X1,5 M 26X1,5 22 26 1,5 1,5 20,5 24,5 5 4 1 1 1/4 16 20 M 30X1,5 M 38X1,5 30 38 1,5 1,5 14 28,5 36,5 5,5 7 1 1/2 1 3/4 24 28 M 45X1,5 M 52X1,5 45 52 1,5 1,5 14 14 43,5 50,5 8 7,5 2 32 M 65X2,0 65 2,0 17 62,9 9,5 2 1/2 3 40 48 M 78X2,0 M 90X2,0 78 90 2,0 2,0 17 23 75,9 87,9 9,5 15 60 cone sealing arrangments follow DIN 7611 and 7606
Swage Fittings Catalogue - 19 Technical guide TECHNICAL GUIDE Catalogue pages for METRIC 60 cone type S 711 S 7 S 713 Female METRIC 60 cone crimped nut Page 58 S 781 Female METRIC 60 cone 45 swept elbow crimped nut Page 59 S 782 Female METRIC 60 cone 90 swept elbow crimped nut Page 60 S 783 Female METRIC 60 cone slip-on nut Page 61 Female METRIC 60 cone 45 swept elbow slip-on nut Page 61 Female METRIC 60 cone 90 swept elbow slip-on nut Page 61
TECHNICAL GUIDE 20 - Swage Fittings Catalogue Technical guide 3 2 Type B.S.P (British Standard Pipe) suivant BS 5200 3 2 1 BSP (British Standard Pipe) type according to BS 5200 BSP 60 cone sealing arrangement Sealing : 60 male cone into 60 female cone Connection : parallel Whitworth thread according to BS 2779 (equivalent to French standard NFE 03-005), whose thread is expressed in threads per inch. The profile of this thread is is an isosceles triangle with a flank angle of 55 and truncated top and bottom. (This thread inspired the French Gaz thread). Metal to metal sealing 60 BSP 60 cone type thread P 30 DE DA L Number Male Thread Circuit Thread Female thread Free length Outer Pitch Common Thread Size of Threads Diameter Length (L) inner diameter (P) dia. Dash per inch (DE)(mm) (mm) (DA) (mm) (mm) (mm) designation 1/8 1/4 2 4 1/8 1/4 28 19 9,7 13,1 11,4 11,4 8,5 11,4 4,3 5,8 0,90 1,33 5/10 8/13 3/8 1/2 6 8 3/8 1/2 19 14 16,6 20,9,7 15,2 14,9 18,6 6,8 8,1 1,33 1,81 /17 15/21 5/8 3/4 10 5/8 3/4 14 14 22,9 26,4 17,7 19 20,6 24,1 8,4 9,6 1,81 1,81 16/23 20/27 7/8 1 14 16 7/8 1 14 11 30,2 33,2 19 20,3 27,9 30,3 10,3 11,3 1,81 2,30 24/31 26/34 1 1/4 1 1/2 20 24 1 1/4 1 1/2 11 11 41,9 47,8 21,1 21,6 38,9 44,8,4,4 2,30 2,30 33/42 40/49 1 3/4 28 1 3/4 11 53,7 22,2 50,8,4 2,30 45/55 2 32 2 11 59,6 22,2 56,6,4 2,30 50/60 2 1/2 40 2 1/2 11 75,2 30 72,2 20 2,30 66/76
Swage Fittings Catalogue - 21 Technical guide TECHNICAL GUIDE Catalogue pages for BSP 60 cone S 311 S 471 S 472 S 473 Male BSP Page 62 Female BSP crimped nut Page 63 Female BSP crimped nut 45 swept elbow Page 64 Female BSP crimped nut 90 swept elbow Page 65 S 461 S 462 S 463 S 453 Female BSP slip-on nut Page 66 Female BSP 45 swept elbow slip-on nut Page 66 Female BSP 90 swept elbow slip-on nut Page 66 Female BSP 90 compact elbow slip-on nut Page 66
TECHNICAL GUIDE 22 - Swage Fittings Catalogue Technical guide 3 2 2 BSP (British Standard Pipe) 60 cone type with O-ring BSP 60 cone with O-ring sealing arrangement Sealing : O-ring on 60 male cone into 60 female cone Connection : parallel Whitworth thread according to BS 2779 (equivalent to French standard NFE 03-005), whose thread is expressed in threads per inch. The profile of this thread is is an isosceles triangle with a flank angle of 55 and truncated top and bottom. (This thread inspired the French Gaz thread). Sealing by O-ring 60 BSP 60 cone with O-ring type P 30 DE DA L Number Male Thread Circuit Thread Female thread Free length Outer Pitch Common Thread Size of Threads Diameter Length (L) inner diameter (P) dia. Dash per inch (DE)(mm) (mm) (DA) (mm) (mm) (mm) designation 1/8 1/4 2 4 1/8 1/4 28 19 9,7 13,1 11,4 11,4 8,5 11,4 4,3 5,8 0,90 1,33 5/10 8/13 3/8 1/2 6 8 3/8 1/2 19 14 16,6 20,9,7 15,2 14,9 18,6 6,8 8,1 1,33 1,81 /17 15/21 5/8 3/4 10 5/8 3/4 14 14 22,9 26,4 17,7 19 20,6 24,1 8,4 9,6 1,81 1,81 16/23 20/27 7/8 1 14 16 7/8 1 14 11 30,2 33,2 19 20,3 27,9 30,3 10,3 11,3 1,81 2,30 24/31 26/34 1 1/4 1 1/2 20 24 1 1/4 1 1/2 11 11 41,9 47,8 21,1 21,6 38,9 44,8,4,4 2,30 2,30 33/42 40/49 1 3/4 28 1 3/4 11 53,7 22,2 50,8,4 2,30 45/55 2 32 2 11 59,6 22,2 56,6,4 2,30 50/60 2 1/2 40 2 1/2 11 75,2 30 72,2 20 2,30 66/76
Swage Fittings Catalogue - 23 Technical guide TECHNICAL GUIDE Catalogue pages for BSP 60 cone with O-ring S 311 S 481 S 482 S 483 Male BSP Page 62 Female BSP O-ring crimped nut Page 67 Female BSP O-ring crimped nut 45 swept elbow Page 67 Female BSP O-ring crimped nut 90 swept elbow Page 68 SD 311 SD 481 SD 482 SD 483 Male BSP Page 69 Female BSP O-ring thrust-wire nut Page 69 Female BSP O-ring thrust-wire nut 45 swept elbow Page 69 Female BSP O-ring thrust-wire nut 90 swept elbow Page 69 SC 311 SC 481 SC 482 SC 483 Male BSP Page 70 Female BSP O-ring thrust-wire nut Page 70 Female BSP O-ring thrust-wire nut 45 swept elbow Page 70 Female BSP O-ring thrust-wire nut 90 swept elbow Page 70
TECHNICAL GUIDE 24 - Swage Fittings Catalogue Technical guide 3 2 3 BSP (British Standard Pipe) flat seat type BSP flat seat sealing arrangement Sealing : compression of a joint between two machined flat surfaces Connection : parallel Whitworth thread according to BS 2779 (equivalent to French standard NFE 03-005), whose thread is expressed in threads per inch. The profile of this thread is is an isosceles triangle with a flank angle of 55 and truncated top and bottom. (This thread inspired the French Gaz thread). BSP flat seat type Sealing by flat joint L P DE DA dia. 1/4 3/8 1/2 5/8 3/4 1 Circuit Dash 4 6 8 10 16 Thread Size 1/4 3/8 1/2 5/8 3/4 1 Number of Threads per inch 19 19 14 14 14 11 Male Thread Outer Diameter (DE)(mm) 13,1 16,6 20,9 22,9 26,4 33,2 Thread Length (L) (mm) 11 14 16 16 19 Female thread inner diameter (DA) (mm) 11,4 14,9 18,6 20,8 24,1 30,3 Free length (P) (mm) 8 10,6 11,1 14 15 Pitch (mm) 1,33 1,33 1,81 1,81 1,81 2,30 Common designation 8/13 /17 15/21 16/23 20/27 26/34 Catalogue pages for BSP flat seat type S 331 S 421 Male BSP flat seat Page 71 Female BSP flat seat Page 71
Swage Fittings Catalogue - 25 Technical guide TECHNICAL GUIDE 3 2 4 BSP taper thread BSP taper thread sealing arrangement Sealing : mating of threads combined with sealing tape or liquid. Connection : parallel Whitworth thread according to BS 21 (equivalent to NFE 03-004, EN 10226 and ISO 7), whose pitch is expressed in threads per inch. The thread is machined to a 6.25% taper. This system is widely used in France. 6,25% BSP taper type G Sealing by tape or liquid DE DA L 6,25% Number Male Thread Circuit Thread Thread Size Pitch G Female thread Outer Common of Threads per (pouce) inch (mm) Diameter Length (L) inner diameter dia. Dash (mm) (DE)(mm) (mm) (DA) (mm) designation 1/8 2 1/8 28 0,90 3,9 9,7 9 8,5 5/10 1/4 4 1/4 19 1,33 6 13,1,5 11,4 8/13 3/8 6 3/8 19 1,33 6,3 17,6 13 14,9 /17 1/2 8 1/2 14 1,81 8,1 20,9 17 18,6 15/21 5/8 10 5/8 14 1,81 22,9 18 20,6 16/23 3/4 3/4 14 1,81 9,5 26,4 18,5 24,1 20/27 7/8 14 7/8 14 1,81 30,2 20 27,9 24/31 1 16 1 11 2,30 10,3 32,2 21 30,3 26/34 1 1/4 20 1 1/4 11 2,30,7 41,9 23,5 38,9 33/42 1 1/2 24 1 1/2 11 2,30,7 47,8 23,5 44,8 40/49 1 3/4 28 1 3/4 11 2,30 53,7 28 50,9 45/55 2 32 2 11 2,30 15,8 59,6 28 56,6 50/60 2 1/2 40 2 1/2 11 2,30 17,4 75,2 32 72,2 66/76 3 48 3 11 2,30 20,6 87,8 35 84,9 80/90 Pagination type GAZ CONIQUE Type Référence Désignation Page S S 321 Male BSP taper 72 SD SD 321 Male BSP taper 72 SC SC 321 Male BSP taper 72
TECHNICAL GUIDE 26 - Swage Fittings Catalogue Technical guide 3 3 JIC (Joint Industrial Council) according to SAE J516 JIC sealing arangement Sealing : 74 male cone on 74 female cone Connection : parallel normalised according to ASME B1.1 (ex-sellers) and ISO 263, whose external diameter is expressed in inch and its pitch in threads per inch. The profile of this thread is an equilateral triangle. 74 Metal to metal sealing JIC type thread L P DE 37 DA Number Male Thread Circuit Thread Female thread Free length Outer Pitch Thread Thread Size of Threads Diameter Length (L) inner diameter (P) dia. Dash per inch (DE)(mm) (mm) (DA) (mm) (mm) (mm) family 1/8 3/16 2 3 5/16 3/8 24 24 7,9 9,5 11,3,3 6,7 8,3 8,4 8,7 1,05 1,05 UNF UNF 1/4 5/16 4 5 7/16 1/2 20 20 11,1,7 13,9 13,9 9,7 11,3 8,7 9,5 1,27 1,27 UNF UNF 3/8 1/2 6 8 9/16 3/4 18 16 14,2 19 14,1 16,6,7 17,3 9,5 10,7 1,41 1,58 UNF UNF 5/8 3/4 10 7/8 1 1/16 14 22 26,9 19,2 21,9 20,2 24,6,7 14,2 1,81 2,11 UNF UN 7/8 1 14 16 1 3/16 1 5/16 30,1 33,3 22,6 23,1 27,8 31 14,6 15 2,11 2,11 UN UN 1 1/4 1 1/2 20 24 1 5/8 1 7/8 41,2 47,6 24,3 27,5 38,9 45,3 15,8 18,6 2,11 2,11 UN UN 2 2 1/2 32 40 2 1/2 3 63,5 76,2 33,8 45 61,2 74,1 23,8 20,2 2,11 2,11 UN UN 3 48 3 1/2 88,9 45 86,5 22,2 2,11 UN
Swage Fittings Catalogue - 27 Technical guide TECHNICAL GUIDE Catalogue pages for JIC type S 111 S 211 S 2 S 213 S 216 Male JIC 74 cone Female JIC 74 cone Female JIC 74 cone 45 swept elbow Female JIC 74 cone 90 swept elbow Female JIC 74 cone Double Hexagon Page 73 Page 74 Page 75 Page 76 Page 76 SD 111 SD 211 SD 2 SD 213 Male JIC 74 cone Female JIC 74 cone Female JIC 74 cone 45 swept elbow Female JIC 74 cone 45 swept elbow Page 77 Page 77 Page 77 Page 78 SC 111 SC 211 SC 2 SC 213 Male JIC 74 cone Female JIC 74 cone Female JIC 74 cone 45 swept elbow Female JIC 74 cone 45 swept elbow Page 79 Page 79 Page 79 Page 80
TECHNICAL GUIDE 28 - Swage Fittings Catalogue Technical guide 3 4 Flange collar type according to SAE J516 SAE flange sealing Sealing : by O-ring lodged in a groove machined into the collar Connection : by one-piece or half-flanges fixed by bolts Sealing by O-ring Catalogue pages for SAE flange fittings S 811 S 8 S 813 S 861 S 862 S 863 SAE flange 3000 psi Page 81 SAE flange 3000 psi 45 swept elbow Page 81 SAE flange 3000 psi 90 swept elbow Page 82 SAE flange 6000 psi Page 85 SAE flange 6000 psi 45 swept elbow Page 85 SAE flange 6000 psi 90 swept elbow Page 86 S 881 S 882 S 883 S 891 S 892 S 893 SAE flange Supercat 3000 psi Page 89 SAE flange Supercat 45 swept elbow Page 89 SAE flange Supercat 90 swept elbow Page 89 SAE flange Komatsu Page 109 SAE flange Komatsu 45 swept elbow Page 109 SAE flange Komatsu 90 swept elbow Page 109
Swage Fittings Catalogue - 29 Technical guide TECHNICAL GUIDE SD 811 SD 8 SD 813 SD 861 SD 862 SD 863 SAE flange 3000 psi Page 83 SAE flange 3000 psi 45 swept elbow Page 83 SAE flange 3000 psi 90 swept elbow Page 83 SAE flange 6000 psi Page 87 SAE flange 6000 psi 45 swept elbow Page 87 SAE flange 6000 psi 90 swept elbow Page 87 SD 881 SD 882 SD 883 SC 811 SC 8 SC 813 SAE flange Supercat Page 90 SAE flange Supercat 45 swept elbow Page 90 SAE flange Supercat 90 swept elbow Page 90 SAE flange 3000 psi Page 84 SAE flange 3000 psi 45 swept elbow Page 84 SAE flange 3000 psi 90 swept elbow Page 84 SC 861 SC 862 SC 863 SC 881 SC 882 SC 883 SAE flange 6000 psi Page 88 SAE flange 6000 psi 45 swept elbow Page 88 SAE flange 6000 psi 90 swept elbow Page 88 SAE flange Supercat Page 91 SAE flange Supercat 45 swept elbow Page 91 SAE flange Supercat 90 swept elbow Page 91 994 994 994 994 903 half-flange 3000 psi Page 92 one-piece flange 3000 psi Page 92 half-flange 6000 psi Page 93 one-piece flange 6000 psi Page 93 O-ring Page 93
TECHNICAL GUIDE 30 - Swage Fittings Catalogue Technical guide 3 5 ORFS (O-Ring Face Seal) according to SAE J516 ORFS sealing arrangement Sealing : by compression of a joint lodged in a groove on a machined face against a flat seat. Connection : parallel thread normalised according to ASME B1.1 (ex-sellers) and ISO 263, whose external diameter is expressed in inches and its pitch in threads per inch. The profile of the thread is an equilateral triangle. Dating back to the late 1980 s, this sealing arrangement was designed to eliminate leaks due to vibrations and various other constraints on earth-moving equipment. Sealing by O-ring ORFS type thread L P DE DA dia. 1/4 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 Circuit Dash 4 6 8 10 16 20 24 Thread Size (inch) 9/16 11/16 13/16 1 1 3/16 1 7/16 1 11/16 2 Number of Threads per inch 18 16 16 14 Pitch (mm) 1,41 1,58 1,58 1,81 2,11 2,11 2,11 2,11 Male Thread Outer Diameter (DE)(mm) 14,3 17,5 20,6 25,4 30,2 36,5 42,5 50,8 Thread Length (L) (mm) 9,8 11,2,8 15,5 17 17,5 17,5 17,5 Female thread inner diameter (DA) (mm),7 15,7 18,9 23,5 27,9 34,2 40,6 48,5 Free length (P) (mm) 8,2 9,5 11 13,5 14,5 14,8 14,8 14,8
Swage Fittings Catalogue - 31 Technical guide TECHNICAL GUIDE Catalogue pages for ORFS type S 181 S 281 S 282 S 283 Male ORFS Flat seat O-ring Page 94 Female ORFS Flat seat O-ring Page 94 Female ORFS Flat seat O-ring 45 swept elbow Page 95 Female ORFS Flat seat O-ring 90 swept elbow Page 95 SD 181 SD 281 SD 282 SD 283 Male ORFS Flat seat O-ring Page 96 Female ORFS Flat seat O-ring Page 96 Female ORFS Flat seat O-ring 45 swept elbow Page 96 Female ORFS Flat seat O-ring 90 swept elbow Page 96 SC 181 SC 281 SC 282 SC 283 Female ORFS Flat seat Female ORFS Flat seat O-ring O-ring 45 swept elbow Page 97 Page 97 Page 97 Page 97 Male ORFS Flat seat O-ring Female ORFS Flat seat O-ring 90 swept elbow
TECHNICAL GUIDE 32 - Swage Fittings Catalogue Technical guide 3 6 NPT (National Pipe Thread) according to SAE J516 NPT sealing arrangment Sealing : ensured by tight contact of male and female thread flanks (metal to metal) induced by tapered finish. Connection : thread normalised according to ASME and ANSI B1.20.1 (in France NFE 03-601), tapered slope of 6.25%, for both male and female threads, usually expressed in inches and pitch in threads per inch. The thread profile is that of an equilateral triangle with a peak angle of 60 and salient truncation (sometimes wrongly called Briggs). 6,25% Metal to metal sealing NPT thread type G 6,25% P DE DC DP 6,25% L Circuit dia. 1/16 1/8 Dash 1 2 1/4 4 3/8 6 1/2 8 3/4 1 16 1 1/4 20 1 1/2 24 2 32 2 1/2 3 40 48 Thread Size (inch) 1/16 1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 Number of Threads per inch 27 27 18 18 14 14 11 1/2 11 1/2 11 1/2 11 1/2 8 8 Male Thread Outer Diameter (DE)(mm) 7,7 9,72 13,1 16,6 20,5 26,4 33,2 41,9 47,8 56,6 75,2 87,8 Thread Length (L) (mm) 9,5 9,5 14,3 14,3 19 19 23,8 24,6 25,4 26,2 38,5 40,1 Drill dia.(dp) (mm) 6,3 8,3 10,7 14,3 17,5 22,6 28,6 37,3 44,1 56,4 67,1 82,9 Taper Size (DC) (mm) 6,6 8,8 11,4 15,1 18,5 23,6 29,8 38,6 44,8 56,8 68,5 84,4 Pitch (mm) 0,94 0,94 1,41 1,41 1,81 1,81 2,21 2,21 2,21 2,21 3,18 3,18 G (mm) 3,9 3,9 6 6,3 8,1 9,5 10,4,7,7 15,8 17,4 20,6 Drill length (P) (mm) 11,7 11,7 17 17,3 22,9 23,1 28,9 29,4 29,4 30 46,8 48,4
Swage Fittings Catalogue - 33 Technical guide TECHNICAL GUIDE Catalogue pages for NPT type S 1 Male NPT Page 99 SD 1 Male NPT Page 98 SC 1 Male NPT Page 98 AQ 1 Male NPT Page 111
TECHNICAL GUIDE 34 - Swage Fittings Catalogue Technical guide 3 7 SAE type 3 7 1 SAE (Society of Automotive Engineers) according to SAE J516 with 90 cone SAE 90 cone sealing arrangement Sealing : parallel thread normalised according to ASME B1.1 (ex-sellers) and ISO 263, whose external diameter is expressed in inches and pitch in threads per inch. The thread profile is that of an equilateral triangle. NOTE : SAE type fittings are only used up to dash size inclusive. Despite their close resemblance to JIC type, except for their sealing cone angle, dash sizes 6 and are not common to the two systems. Dash size 6 differs by diameter and pitch and dash size by pitch. 90 Metal to metal sealing SAE 90 cone thread type L P DE 45 DA Number Male Thread Circuit Thread Female thread Thread Size Longueur Free length Outer Thread of Threads (inch) Diameter Length (L) inner diameter libre (P) (P) dia. Dash per inch (DE)(mm) (mm) (DA) (mm) (mm) (mm) family 3/16 1/4 3 4 3/8 7/16 24 20 9,5 11,1 11,1 13,9 8,3 9,7 8,6 8,3 1,05 1,27 UNF UNF 5/16 3/8 5 6 1/2 5/8 20 18,7 15,8 14,6 15,8 11,3 14,3 9,5 10,6 1,27 1,41 UNF UNF 1/2 5/8 8 10 3/4 7/8 16 14 19 22,2 19 22,2 17,3 20,2 13,4 14,6 1,58 1,81 UNF UNF 3/4 1 1/16 14 26,9 25,4 24,9 14,6 1,81 UNS
Swage Fittings Catalogue - 35 Technical guide TECHNICAL GUIDE SAE inverted 90 cone type L P 45 DE DA 45 Circuit Number Thread Size Pitch Male Thread Thread Length Female thread Free length of Threads per Outer Diameter (L) inner diameter (P) dia. Dash (inch) inch (mm) (DE)(mm) (mm) (DA) (mm) (mm) 1/8 3/16 2 3 5/16 3/8 28 24 0,90 1,05 7,9 9,5 8,1 9,1 6,9 8,4 4,7 5,1 1/4 5/16 4 5 7/16 1/2 24 20 1,05 1,27 11,1,7 9,1 10,1 9,9 11,3 5,1 5,9 3/8 7/16 6 7 5/8 11/16 18 18 1,41 1,41 15,8 17,4 10,1 11,2 14,3 15,9 6,7 7,5 1/2 8 3/4 18 1,41 19 11,7 17,5 7,9 5/8 10 7/8 18 1,41 22,2,2 20,7 8,33 3/4 11/16 16 1,58 26,9 13,7 25,3 9,1 catalogue pages for SAE 90 cone type S 131 S 221 S 222 S223 Male SAE 90 cone Page 100 Female SAE 90 cone Page 100 Female SAE 90 cone 45 swept elbow Page 101 Female SAE 90 cone 90 swept elbow Page 101
TECHNICAL GUIDE 36 - Swage Fittings Catalogue Technical guide 3 7 2 SAE (Society of Automotive Engineers) flat seat according to SAE J516 SAE flat seat O-ring sealing arrangement Sealing : by compression of an O-ring Connection : parallel thread normalised according to ASME B1.1 (ex-sellers) and ISO 263, whose external diameter is expressed in inches and pitch in threads per inch. The thread profile is that of an equilateral triangle. Sealing by O-ring SAE type thread L P DE DA Number Male Thread Circuit Thread Female thread Free length Thread Size Outer Pitch Thread of Threads (inch) Diameter Length (L) inner diameter (P) dia. Dash per inch (DE)(mm) (mm) (DA) (mm) (mm) (mm) family 1/8 3/16 2 3 5/16 3/8 24 24 7,9 9,5 11,3,3 6,7 8,3 8,4 8,7 1,05 1,05 UNF UNF 1/4 5/16 4 5 7/16 1/2 20 20 11,1,7 13,9 13,9 9,7 11,3 8,7 9,5 1,27 1,27 UNF UNF 3/8 1/2 6 8 9/16 3/4 18 16 14,2 19 14,1 16,6,7 17,3 9,5 10,7 1,41 1,58 UNF UNF 5/8 3/4 10 7/8 1 1/16 14 22 26,9 19,2 21,9 20,2 24,6,7 14,2 1,81 2,11 UNF UN 7/8 1 14 16 1 3/16 1 5/16 30,1 33,3 22,6 23,1 27,8 31 14,6 15 2,11 2,11 UN UN 1 1/4 1 1/2 20 24 1 5/8 1 7/8 41,2 47,6 24,3 27,5 38,9 45,3 15,8 18,6 2,11 2,11 UN UN 2 2 1/2 32 40 2 1/2 3 63,5 76,2 33,8 45 61,2 74,1 23,8 20,2 2,11 2,11 UN UN 3 48 3 1/2 88,9 45 86,5 22,2 2,11 UN Catalogue pages for SAE flat seat O-ring type Type Référence Désignation Page S S 141 SAE flat seat O-ring 100
Swage Fittings Catalogue - 37 Technical guide TECHNICAL GUIDE 3 8 MISCELLANEOUS 3 8 1 BANJO type Banjo type sealing arrangement Sealing : by flat joint each side of banjo Connection : by metric or imperial threaded hollow bolt Metal to metal sealing by flat joint Catalogue pages for BANJO type S 941 227 Metric banjo Page 102 S 921 Metric banjo bolt Page 102 227 BSP banjo Page 103 BSP banjo bolt Page 103
TECHNICAL GUIDE 38 - Swage Fittings Catalogue Technical guide 3 8 2 JIS (Japanese Industrial Standard) according to JIS B8363 JIS type sealing arrangment Sealing : 60 male cone into 60 female cone. Connection : parallel Whitworth thread according to BS 5200 (French equivalent NFE 03-005) whose pitch is expressed in threads per inch. The thread profile is that of an isosceles triangle with 55 angle crest and rounded truncation. NOTE : A resemblance can be noted with JIC and SAE types. The metric JIS type uses the same sealing arrangement but with a metric thread. 60 Metal to metal sealing JIS Whitworth thread TOYOTA type L P DE 30 DA dia. Circuit Dash Thread Size (inch) Number of Threads per Pitch (mm) Male Thread Outer Diameter (DE)(mm) Thread Length (L) Female thread inner diameter (DA) (mm) Free length (P) inch (mm) (mm) 1/4 4 1/4 19 1,33 13,1 16 11,4 8 3/8 6 3/8 19 1,33 16,6 17,5 14,9 10 1/2 8 1/2 14 1,81 20,9 20 18,6 11 3/4 3/4 14 1,81 26,4 21,5 24,1,5 1 16 1 11 2,30 33,2 24 30,3 14,5
Swage Fittings Catalogue - 39 Technical guide TECHNICAL GUIDE JIS metric thread KOMATSU type L P DE 60 DA dia. 5/16 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 Circuit Dash 5 6 8 10 16 20 24 Thread Size (inch) 14X1,50 16X1,50 18X1,50 22X1,50 24X1,50 30X1,50 33X1,50 36X1,50 Male Thread Outer Diameter (DE)(mm) 14 16 18 22 24 30 33 36 Pitch (mm) 1,50 1,50 1,50 1,50 1,50 1,50 1,50 1,50 Thread Length (L) (mm) Female thread inner diameter (DA) (mm),45 14 16,5 20,5 22,5 28,5 31,5 34,5 Free length (P) (mm) 10,5 9,5 11,5 14 15 18,3 21,3 20 Catalogue pages for JIS type S 491 S 791 Female JIS BSP 60 cone Page 108 Female JIS METRIC 60 cone Page 108
TECHNICAL GUIDE 40 - Swage Fittings Catalogue Technical guide 3 8 3 STAND-PIPE type STAND-PIPE sealing arrangment Sealing : by compression of a ring on the tube into a female 24 cone Connection : ISO profile parallel metric thread Sealing by metal ring Catalogue pages for STAND-PIPE type S 511 S 5 S 513 S 521 Metric Stand-Pipe Metric Stand-Pipe 45 swept elbow Metric Stand-Pipe 90 swept elbow French Gaz Stand-Pipe Page 104 Page 105 Page 106 Page 107
Swage Fittings Catalogue - 41 Technical guide TECHNICAL GUIDE 4 TORQUE VALUES (N/M) Nominal thread diameter 1/8 1/4 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 1 1 1/16 1 3/16 1 1/4 1 5/16 1 7/16 1 1/2 1 11/16 1 5/8 1 7/8 2 2 1/2 Tube diameter (mm) 6 8 10 13 14 15 16 17 18 20 21 22 25 27 28 30 33 35 38 42 49 B.S.P Fittings J.I.C O.R.F.S 471 / 472 / 473 211 / 2 / 213 261 / 262 / 263 15 N/m 15-25 N/m 27-41 N/m 9-21 N/m 42-76 N/m 13-27 N/m 18-42 N/m 16 N/m 44-94 N/m 27 N/m 95-135 N/m 30-70 N/m 47 N/m 44-94 N/m 115-165 N/m 68 N/m 63-133 N/m 73-163 N/m 95 N/m 140-280 N/m 90-190 N/m 135 N/m 215-365 N/m 190 N/m 135-285 N/m 215-365 N/m 300-500 N/m 225 N/m 300-500 N/m Fittings French Gaz L Series S Series 741 / 742 /743 761 / 762 /763 771 / 772 /773 15-25 N/m 30-45 N/m 30-45 N/m 38-52 N/m 38-52 N/m 43-58 N/m 43-58 N/m 50-65 N/m 40-50 N/m 60-88 N/m 60-88 N/m 60-88 N/m 70-80 N/m 85-5 N/m 115-155 N/m 80-0 N/m 115-155 N/m 140-192 N/m 0-210 N/m 140-192 N/m 210-270 N/m 210-240 N/m 255-325 N/m 280-380 N/m 240-270 N/m 280-380 N/m 280-340 N/m
TECHNICAL GUIDE 42 - Swage Fittings Catalogue Technical guide 5 THREAD IDENTIFICATION To identify the type and size of a thread, it is necessary to measure : - either the external diameter of the thread (DE) when it is a male thread - or the internal diameter of the thread (DA) when it is a female thread In the case of a taper thread, the diameter should be measured at a distance G from the end of the thread. The following table should then be consulted. In case of doubt, a thread gauge should be used to measure the pitch and angle of the threads. Identification of fittings according to thread diameters Ø measured on threads DE DA Measured dimensions are identical for SD, SC and AQ ranges DE or DA (mm) Male fitting Female fitting 8,7 S471 02 9 S711 10 9,6 S311 02 / S321 02 9,9 S611 10 S211 07 / S216 07 10,5 S711 / S761 06 11 S111 07 / S141 07 11,5 S211 08 / S216 08 11,7 S421 04 / S461 04 / S471 04 / S481 04 / S491 04 11,85 S611 / S621,4 S711 14 / S791 14,55 S111 08 S761 08 / S771 06,67 S141 08,9 S211 09 / S216 09 / S281 04 13 S311 04 / S321 04 13,9 S611 14 / S621 08 / S631 06 14,1 S111 09 / S181 04 14,2 S141 09 14,4 S221 10 / S711 16 / S791 16 14,5 S711 16 / S761 10 / S711 08 15,2 S421 06 / S461 06 / S471 06 / S481 06 / S491 06 15,85 S611 16 / S621 10 / S631 10 15,9 S281 06 16,4 S711 18 / S761 / S771 10 16,5 S311 06 / S321 06 S711 18 / S791 18 17,3 S181 06 17,5 S211 / S216 17,85 S611 18 / S621 / S631 10 18,5 S711 20 / S741 13 / S771 18,9 S111 S421 08 / S461 08 / S471 08 / S481 08 / S491 08 19 S141 S281 08 19,85 S621 20 / S631 / S641 13 20,5 S181 08 S211 14 / S216 14 / S701 22 / S711 22 S761 15 / S711 14 / S791 22
Swage Fittings Catalogue - 43 Technical guide TECHNICAL GUIDE DE or DA (mm) Male fitting Female fitting 20,8 S311 08 / S321 08 20,9 S421 10 / S471 10 / S481 10 21,85 S611 22 / S621 15 / S631 14 22,1 S111 14 22,18 S141 14 22,5 S711 24 / S741 17 / S771 16 / S791 24 22,8 S311 10 / S321 10 23,25 S281 10 23,85 S611 24 / S641 17 / S631 16 24,4 S421 / S461 / S471 / S481 / S491 24,5 S711 26 / S761 18 25 S211 17 / S216 17 / S221 17 25,2 S181 10 25,85 S611 26 / S621 18 26,3 S311 / S321 26,9 S111 17 / S141 17 28 S281 / S761 22 / S771 20 28,5 S711 30/ S741 21 / S791 30 29,8 S621 22 / S631 20 29,9 S181 / S611 30 / S641 21 30 S111 19 30,6 S421 16 / S461 16 / S471 16 / S481 16 / S491 16 31,3 S211 21 / S216 21 32,85 S791 33 33,1 S311 16 / S321 16 33,2 S111 21 33,3 S141 21 34 S761 28 / S771 25 34,5 S281 16 / S741 27 35,8 S621 28 / S631 25 / S641 27 S791 36 36,3 S181 16 36,5 S711 38 37,85 S611 38 38,8 S211 26 39,2 S421 20 / S461 20 / S471 20 / S481 20 40 S771 30 40,9 S281 20 41,1 S111 26 41,8 S311 20 / S321 20 / S631 30 S791 42 42,7 S181 20 43 S761 35 43,5 S711 45 / S741 33 44,85 S611 45 / S621 35 / S641 33 45 S421 24 / S471 24 / S481 24 45,4 S211 30 47,3 S311 24 / S321 24 47,9 S311 30 48,7 S281 24 50 S761 42 / S771 38 50,6 S181 24 51,8 S621 42 / S631 38 56,7 S421 32 / S471 32 / S481 32 59,3 S311 32 / S321 32 61,2 S211 40 63,5 S111 40
FERRULES 44 - Swage Fittings Catalogue Ferrules for S type inserts 6 5013 5010 5010 FERRULES external skive external skive non-skive 5010 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5010 03 5 4,8 03 3/16 17 26 T 110 T 210 5010 04 6 6,3 04 1/4 19 29 T 110 T 210 5010 05 8 7,9 05 5/16 21 29 T 110 T 210 5010 06 10 9,5 06 3/8 23 31,5 T 110 T 210 5010 08,7 08 1/2 27 34 T 110 T 210 5010 10 16 15,9 10 5/8 32 37 T 110 T 210 5010 20 19,1 3/4 36 43 T 110 T 210 5010 16 25 25,4 16 1 44 49 T 110 T 210 5010 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5010 20 31 31,8 20 1 1/4 50 55 T 110 5010 24 38 38,1 24 1 1/2 57 60 T 110 5010 32 51 50,8 32 2 70 75 T 110 5013 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5013 03 5 4,8 03 3/16 19 24 T 111 T 221 5013 04 6 6,3 04 1/4 20 27 T 111 T 221 5013 05 8 7,9 05 5/16 22 27,5 T 111 T 221 5013 06 10 9,5 06 3/8 25 30 T 111 T 221 5013 08,7 08 1/2 28 32,5 T 111 T 221 5013 10 16 15,9 10 5/8 32 35 T 111 T 221 5013 19 19,1 3/4 36 40 T 111 T 221 5013 16 25 25,4 16 1 45 50 T 111 T 221 5013 20 31 31,8 20 1 1/4 54 50 T 111 5013 24 38 38,1 24 1 1/2 62 55 T 111 5013 32 51 50,8 32 2 76 60 T 111
Swage Fittings Catalogue - 45 Ferrules for S type inserts 5014 non-skive 5014 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5014 04 6 6,3 04 1/4 19 23 T 1 5014 05 8 7,9 05 5/16 20 27,5 T 1 5014 06 10 9,5 06 3/8 23 30 T 1 5014 08,7 08 1/2 26,5 32 T 1 5014 10 16 15,9 10 5/8 29 35 T 1 5014 19 19,1 3/4 33 34 T 1 5014 16 25 25,4 16 1 42 45 T 1 FERRULES 5020 external skive 5020 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5020 20 31 31,8 20 1 1/4 54 55 T 210 5020 24 38 38,1 24 1 1/2 62 60 T 210 5020 32 51 50,8 32 2 75 75 T 210 5023 non-skive 5023 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5023 03 5 4,8 03 3/16 20 24 T 111 T 211 5023 04 6 6,3 04 1/4 22 26 T 111 T 211 5023 05 8 7,9 05 5/16 24 27,5 T 111 T 211 5023 06 10 9,5 06 3/8 26 30 T 111 T 211 5023 08,7 08 1/2 30 32,5 T 111 T 211 5023 10 16 15,9 10 5/8 34 35 T 111 T 211 5023 19 19,1 3/4 38 40 T 111 T 211 5023 16 25 25,4 16 1 48 50 T 211 5023 20 31 31,8 20 1 1/4 60 57 T 211 5023 24 38 38,1 24 1 1/2 67 62 T 211 5023 32 51 50,8 32 2 80 66 T 211
46 - Swage Fittings Catalogue Ferrules for S type inserts FERRULES 5030 non-skive 5030 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5030 04 6 6,3 04 1/4 19 29 T 331 5030 05 8 7,9 05 5/16 22 30 T 331 5030 06 10 9,5 06 3/8 24 31 T 331 5030 08,7 08 1/2 28,5 34 T 331 5030 10 16 15,9 10 5/8 32 36 T 331 5030 20 19,1 3/4 38 42 T 331 5030 16 25 25,4 16 1 46 50 T 331 5030 20 32 31,8 20 1 1/4 52 57 T 331 5040 non-skive 5040 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5040 20 19,1 3/4 38 40 T 410 5040 16 25 25,4 16 1 46 38 T 410 5040 20 32 31,8 20 1 1/4 54 50 T 410 5040 24 40 38,1 24 1 1/2 62 49,5 T 410 5040 32 50 50,8 32 2 73 50 T 410 5040 40 65 40 2 1/2 88 87 T 410 5040 48 75 48 3 104 67 T 410 5070 non-skive 5070 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5070 03 5 4,8 03 3/16 14 27 T 611 T 710 T 810 TTA TTK 5070 04 6 6,3 04 1/4 17 29 T 611 T 710 T 810 TTA TTK 5070 05 8 7,9 05 5/16 19 30 T 611 T 710 T 810 TTA TTK 5070 06 10 9,5 06 3/8 21 31 T 611 T 710 T 810 TTA TTK 5070 08,7 08 1/2 25,5 34 T 611 T 710 T 810 TTA TTK 5070 10 16 15,9 10 5/8 28,5 36 T 611 T 710 T 810 TTA TTK 5070 20 19,1 3/4 32 42 T 611 T 710 T 810 TTA TTK 5070 16 25 25,4 16 1 40 50 T 611 T 710 T 810 TTA TTK
Swage Fittings Catalogue - 47 Ferrules for S type inserts 5071 non-skive Part N 5071 Ferrules for S type inserts Hose inner diameter DN mm Dash inch Dimensions (mm) D L Usable on hose type FERRULES 5071 04 6 6,3 04 1/4 16 29 TTA TTK 5080 non-skive 5080 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) Usable on hose type N DN mm Dash inch D L 5080 03 5 4,8 03 3/16 14 27 THP1 THP2 THP3 5080 04 6 6,3 04 1/4 17 30 THP1 THP2 THP3 5080 05 8 7,9 05 5/16 19 30 THP1 THP2 THP3 5080 06 10 9,5 06 3/8 23 32 THP1 THP2 THP3 5091 external skive 5091 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) Usable on hose type N DN mm Dash inch D L 5091 04 6 6,3 04 1/4 22 29 T 911 5091 06 10 9,5 06 3/8 26 32 5091 08,7 08 1/2 30 35 5091 10 16 15,9 10 5/8 34 39 5091 20 19,1 3/4 38 43,5 5091 16 25 25,4 16 1 46 54 5091 20 32 31,8 20 1 1/4 56 61 5091 24 40 38,1 24 1 1/2 65 68 5091 32 50 50,8 32 2 78 74 T 911 T 210 T 911 T 210 T 911 T 210 T 911 T 210 T 9 T 911 T 210 T 9 T 911 T 210 T 911 T 210 T 911 5092 external skive 5092 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) Usable on hose type N DN mm Dash inch D L 5092 20 32 31,8 20 1 1/4 54 61 T 9 5092 24 40 38,1 24 1 1/2 62 69 5092 32 50 50,8 32 2 76 74 T 9 T 9 T 210
48 - Swage Fittings Catalogue Ferrules for SD type inserts FERRULES 5692 internal & external skive 5692 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5692 20 19,1 3/4 38 60 T 9 T 1310 T 915 5692 16 25 25,4 16 1 46 74,5 T 9 T 1310 T 915 5692 20 32 31,8 20 1 1/4 55 88 T 9 5692 24 40 38,1 24 1 1/2 62 94 T 9 5692 32 50 50,8 32 2 78,5 99 T 9 5693 internal & external skive 5693 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) Usable on hose type N DN mm Dash inch D L 5693 20 32 31,8 20 1 1/4 59,8 88 T 1310 T 915 5693 24 40 38,1 24 1 1/2 67 94 5693 32 50 50,8 32 2 84,5 99 T 1310 T 915 T 1310 T 915
Swage Fittings Catalogue - 49 Ferrules for SC type inserts 5093 non-skive 5093 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L 5093 20 3/4 43 50 T911 5093 16 25 16 1 51 56 T911 5093 20 32 20 1 1/4 61 68 5093 24 40 24 1 1/2 70 86 5093 32 50 32 2 85 100 Usable on hose type T9 T9 T9 T9 T9 T1310 T1310 T915 T915 FERRULES 5094 external skive 5094 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L 5094 20 3/4 38 54 T911 5094 16 25 16 1 46 60 T911 5094 20 32 20 1 1/4 54 72 5094 24 40 24 1 1/2 62 90 5094 32 50 32 2 76 102 Usable on hose type T9 T9 T9 T9 T9 T1310 T1310 T915 T915 5096 external skive 5096 Ferrules for S type inserts Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose type 5096 20 32 20 1 1/4 58 72 T911 T 1310 T 915 5096 24 40 24 1 1/2 68 90 T911 T 1310 T 915 5096 32 50 32 2 84 102 T911 T 1310
50 - Swage Fittings Catalogue Metric light series S type insert METRIC 7 S 621 INSERTS S 621 MALE METRIC 24 CONE - LIGHT SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y D S/P G (bars) S 621 06 03 MX1,5 6 21 46 6 10 3/16 5 03 4,8 S 621 08 03 M14X1,5 8 21 46 8 14 10 280 S 621 06 04 MX1,5 6 21 49 6 10 S 621 08 04 M14X1,5 8 21 49 8 14 10 1/4 6 04 6,3 S 621 10 04 M16X1,5 10 23 51 10 17 11 280 S 621 04 M18X1,5 23 51 19 11 S 621 10 05 M16X1,5 10 23 51 10 17 11 5/16 8 05 7,9 S 621 05 M18X1,5 23 51 19 11 280 S 621 10 06 M16X1,5 10 23 53 10 17 11 S 621 06 3/8 10 06 9,5 M18X1,5 23 53 19 11 280 S 621 15 06 M22X1,5 15 25 56 15 22 S 621 15 08 M22X1,5 15 26 59 15 22 280 1/2 08,7 S 621 18 08 M26X1,5 18 28 61 18 27 210 S 621 18 10 M26X1,5 18 28 64 18 27 5/8 16 10 15,9 S 621 22 10 M30X2 22 30 66 22 30 14 210 S 621 18 M26X1,5 18 29 70 18 27 S 621 22 M30X2 22 31 72 22 30 14 210 S 621 28 16 1 25 16 25,4 M36X2 28 35 86 28 36 14 165 S 621 35 20 1 1/4 32 20 31,8 M45X2 35 40 97 35 46 30 5 S 621 42 24 1 1/2 40 24 38,1 M52X2 42 42 106 42 55 36 100 S 761 S 761 FEMALE METRIC 24 CONE O-RING - LIGHT SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y D S/P G (bars) S 761 06 03 Mx1,5 6 21 46 14 1 3/16 5 03 4,8 S 761 08 03 M14x1,5 8 21 46 17 1 280 S 761 06 04 Mx1,5 6 23 51 17 1 S 761 08 04 M14x1,5 8 22 50 17 1 1/4 6 04 6,3 S 761 10 04 M16x1,5 10 24 52 19 3,5 280 S 761 04 M18x1,5 24 52 22 2 S 761 10 05 M16x1,5 10 24 52 19 3,5 5/16 8 05 7,9 S 761 05 M18x1,5 24 52 22 2 280 S 761 10 06 M16x1,5 10 23 54 19 3,5 S 761 06 3/8 10 06 9,5 M18x1,5 24 54 22 2 280 S 761 15 06 M22x1,5 15 24 54 27 4 S 761 15 08 M22x1,5 15 24 27 4 280 1/2 08,7 S 761 18 08 M26x1,5 18 26 59 32 3 210 S 761 18 10 M26x1,5 18 27 32 5/8 16 10 15,9 3 S 761 22 10 M30x2 22 28 64 36 3 210 S 761 18 M26x1,5 18 34 32 3 S 761 22 M30x2 22 31 71 36 3 210 S 761 28 16 1 25 16 25,4 M36x2 28 32 83 41 7 165 S 761 35 20 1 1/4 32 20 31,8 M45x2 35 36 94 50 8,7 5 S 761 42 24 1 1/2 40 24 38,1 M52x2 42 37 102 60 100
Swage Fittings Catalogue - 51 Metric light series S type insert S 762 S 763 S 762 FEMALE METRIC 24 CONE O-RING 45 SWEPT ELBOW LIGHT SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y D S/P G (bars) S 762 06 03 Mx1,5 6 34 59 14 14 1 3/16 5 03 4,8 S 762 08 03 M14x1,5 8 35 60 14 17 1 280 S 762 06 04 Mx1,5 6 35 63 14 17 1 S 762 08 04 M14x1,5 8 36 64 14 17 1 1/4 6 04 6,3 S 762 10 04 M16x1,5 10 38 66 16 19 3,5 280 S 762 04 M18x1,5 39 67 17 22 2 S 762 10 05 M16x1,5 10 39 67 17 19 3,5 5/16 8 05 7,9 S 762 05 M18x1,5 39 67 18 22 2 280 S 762 10 06 M16x1,5 10 39 69 16 19 3,5 S 762 06 3/8 10 06 9,5 M18x1,5 40 71 18 22 2 280 S 762 15 06 M22x1,5 15 42 72 19 27 4 S 762 15 08 M22x1,5 15 46 79 19 27 4 280 1/2 08,7 S 762 18 08 M26x1,5 18 47 80 21 32 3 210 S 762 18 10 M26x1,5 18 53 89 22 32 3 5/8 16 10 15,9 S 762 22 10 M30x2 22 54 90 23 36 3 210 S 762 18 M26x1,5 18 66 107 29 32 3 S 762 22 M30x2 22 62 103 25 36 3 210 S 762 28 16 1 25 16 25,4 M36x2 28 80 131 31 41 7 165 S 762 35 20 1 1/4 32 20 31,8 M45x2 35 96 154 40 50 8,7 5 S 762 42 24 1 1/2 40 24 38,1 M52x2 42 115 179 48 60 100 S 763 FEMALE METRIC 24 CONE O-RING 90 SWEPT ELBOW LIGHT SERIES Part Hose inner diameter Thread Tube Dimensions (mm) N inch DN Dash mm F mm W Y D S/P G S 763 06 03 MX1,5 6 27 52 28 14 1 3/16 5 03 4,8 S 763 08 03 M14X1,5 8 27 52 28 17 1 S 763 06 04 MX1,5 6 26 53 26 17 1 S 763 08 04 M14X1,5 8 29 57 29 17 1 1/4 6 04 6,3 S 763 10 04 M16X1,5 10 29 57 30 19 3,5 S 763 04 M18X1,5 29 57 32 22 2 S 763 10 05 5/16 8 05 7,9 M16X1,5 10 31 59 33 19 3,5 S 763 05 M18X1,5 28 56 32 22 2 S 763 10 06 M16X1,5 10 31 61 31 19 3,5 S 763 06 3/8 10 06 9,5 M18X1,5 31 61 33 22 2 S 763 15 06 M22X1,5 15 31 61 35 27 4 S 763 15 08 M22X1,5 15 37 70 38 27 4 1/2 08,7 S 763 18 08 M26X1,5 18 37 70 40 32 3 S 763 18 10 M26X1,5 18 44 80 45 32 3 5/8 16 10 15,9 S 763 22 10 M30X2 22 44 80 47 36 3 S 763 18 M26X1,5 18 54 94 57 32 3 S 763 22 M30X2 22 54 94 52 36 3 S 763 28 16 1 25 16 25,4 M36X2 28 70 1 66 41 7 S 763 35 20 1 1/4 32 20 31,8 M45X2 35 84 141 83 50 8,7 S 763 42 24 1 1/2 40 24 38,1 M52X2 42 100 164100 60 (bars) 280 280 280 280 280 210 210 210 165 5 100 METRIC
52 - Swage Fittings Catalogue Metric heavy series S type insert METRIC S 631 S 771 S 631 MALE METRIC 24 CONE - HEAVY SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y D S/P G (bars) S 631 06 03 M14X1,5 6 23 48 6 14 3/16 5 03 4,8 S 631 08 03 M16X1,5 8 23 48 8 17 420 S 631 06 04 M14X1,5 6 23 51 6 14 S 631 08 04 M16X1,5 8 23 51 8 17 1/4 6 04 6,3 S 631 10 04 M18X1,5 10 24 52 10 19 450 S 631 04 M20X1,5 25 53 22 S 631 10 05 M18X1,5 10 24 52 10 19 5/16 8 05 7,9 S 631 05 M20X1,5 25 53 22 S 631 10 06 M18X1,5 10 24 55 10 19 S 631 06 3/8 10 06 9,5 M20X1,5 25 56 22 450 S 631 14 06 M22X1,5 14 27 58 14 22 14 S 631 14 08 M22X1,5 14 28 61 14 22 14 1/2 08,7 S 631 16 08 M24X1,5 16 29 62 16 24 14 420 S 631 20 10 5/8 16 10 15,9 M30X2 20 32 68 20 30 16 S 631 20 M30X2 20 33 74 20 30 16 S 631 25 M36X2 25 37 78 25 36 18 S 631 25 16 1 25 16 25,4 M36X2 25 39 90 25 36 18 S 631 30 16 1 25 16 25,4 M42X2 30 43 94 30 46 20 280 S 631 30 20 M42X2 30 44 101 30 46 20 1 1/4 32 20 31,8 S 631 38 20 M52X2 38 48 105 38 55 22 210 S 631 38 24 1 1/2 40 24 38,1 M52X2 38 48 1 38 55 22 185 S 771 FEMALE METRIC 24 CONE - HEAVY SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y S/P G (bars) S 771 06 03 M14x1,5 6 21 46 17 1 3/16 5 03 4,8 S 771 08 03 M16x1,5 8 21 46 19 2,3 420 S 771 06 04 M14x1,5 6 23 51 17 1 S 771 08 04 1/4 6 04 6,3 M16x1,5 8 22 50 19 2,3 S 771 10 04 M18x1,5 10 24 52 22 3,5 450 S 771 04 M20x1,5 24 52 24 3 S 771 10 05 M18x1,5 10 24 52 22 3,5 5/16 8 05 7,9 S 771 05 M20x1,5 24 52 24 3 S 771 10 06 M18x1,5 10 25 55 22 3,5 S 771 06 3/8 10 06 9,5 M20x1,5 24 54 24 3 450 S 771 14 06 M22x1,5 14 28 58 27 4 S 771 14 08 M22x1,5 14 28 27 4 1/2 08,7 S 771 16 08 M24x1,5 16 29 62 30 5 420 S 771 20 10 5/8 16 10 15,9 M30x2 20 33 69 36 4 S 771 20 M30x2 20 36 76 36 4 S 771 25 M36x2 25 38 78 46 7 S 771 25 16 M36x2 25 38 78 41 7 1 25 16 25,4 S 771 30 16 M42x2 30 40 91 50 8,7 S 771 30 20 M42x2 30 41 99 50 8,7 1 1/4 32 20 31,8 S 771 38 20 M52x2 38 45 103 60 280 210 S 771 38 24 1 1/2 40 24 38,1 M52x2 38 46 110 60 185
Swage Fittings Catalogue - 53 Metric heavy series S type insert S 772 S 773 S 772 FEMALE METRIC 24 CONE O-RING 45 SWEPT ELBOW HEAVY SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y X S/P G (bars) S 772 06 03 M14x1,5 6 34 59 14 17 1 3/16 5 03 4,8 S 772 08 03 M16x1,5 8 35 60 14 19 2,3 420 S 772 06 04 M14x1,5 6 35 63 14 17 1 S 772 08 04 M16x1,5 8 36 64 14 19 2,3 1/4 6 04 6,3 S 772 10 04 M18x1,5 10 38 66 16 22 3,5 450 S 772 04 M20x1,5 39 67 17 24 3 S 772 10 05 M18x1,5 10 39 67 17 22 3,5 5/16 8 05 7,9 S 772 05 M20x1,5 39 67 18 24 3 S 772 10 06 M18x1,5 10 40 70 17 22 3,5 S 772 06 3/8 10 06 9,5 M20x1,5 40 71 18 24 3 450 S 772 14 06 M22x1,5 14 42 72 19 27 4 S 772 14 08 M22x1,5 14 46 79 20 27 4 1/2 08,7 S 772 16 08 M24x1,5 16 47 80 21 30 5 420 S 772 20 10 5/8 16 10 15,9 M30x2 20 56 92 25 36 4 S 772 20 M30x2 20 64 105 27 36 4 S 772 25 M36x2 25 64 105 28 46 7 S 772 25 16 M36x2 25 82 133 34 41 7 1 25 16 25,4 S 772 30 16 M42x2 30 80 131 31 50 8,7 S 772 30 20 M42x2 30 96 154 41 50 8,7 1 1/4 32 20 31,8 S 772 38 20 M52x2 38 94 152 38 60 280 210 S 772 38 24 1 1/2 40 24 38,1 M52x2 38 115 180 49 60 185 S 773 FEMALE METRIC 24 CONE O-RING 90 SWEPT ELBOW HEAVY SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y X S/P G (bars) S 773 06 03 M14X1,5 6 27 52 28 17 1 3/16 5 03 4,8 S 773 08 03 M16X1,5 8 27 52 28 19 2,3 420 S 773 06 04 M14X1,5 6 25 53 26 17 1 S 773 08 04 M16X1,5 8 29 57 29 19 2,3 1/4 6 04 6,3 S 773 10 04 M18X1,5 10 29 57 30 22 3,5 450 S 773 04 M20X1,5 29 57 32 24 3 S 773 10 05 M18X1,5 10 31 59 33 22 3,5 5/16 8 05 7,9 S 773 05 M20X1,5 28 56 32 24 3 S 773 10 06 M18X1,5 10 30 61 33 22 3,5 S 773 06 3/8 10 06 9,5 M20X1,5 31 61 33 24 3 450 S 773 14 06 M22X1,5 14 34 64 37 27 4 S 773 14 08 M22X1,5 14 39 71 41 27 4 1/2 08,7 S 773 16 08 M24X1,5 16 39 71 42 30 5 420 S 773 20 10 5/8 16 10 15,9 M30X2 20 44 80 49 36 4 S 773 20 M30X2 20 54 94 55 36 4 S 773 25 M36X2 25 54 94 57 46 7 S 773 25 16 M36X2 25 70 1 70 46 7 1 25 16 25,4 S 773 30 16 M42X2 30 70 1 66 50 8,7 S 773 30 20 M42X2 30 84 141 84 50 8,7 1 1/4 32 20 31,8 S 773 38 20 M52X2 38 84 141 80 60 280 210 S 773 38 24 1 1/2 40 24 38,1 M52X2 38 100 164 101 60 185 METRIC
54 - Swage Fittings Catalogue Metric heavy series SD type insert METRIC SD 773 SD 772 SD 771 SD 631 SD 631 MALE METRIC 24 CONE - HEAVY SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y D S/P G (bars) SD 631 20 M30X2 20 31 93 20 30 16 420 SD 631 25 M36X2 25 35 97 25 36 18 SD 631 25 16 M36X2 25 36 109 25 36 18 414 1 25 16 25,4 SD 631 30 16 M42X2 30 40 113 30 46 20 280 SD 631 30 20 M42X2 30 42 130 30 46 20 1 1/4 32 20 31,8 250 SD 631 38 20 M52X2 38 46 134 38 55 22 SD 631 38 24 1 1/2 40 24 38,1 M52X2 38 47 141 38 55 22 250 SD 771 FEMALE METRIC 24 CONE 0-RING HEAVY SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y S/P G (bars) SD 771 20 M30X2 20 33 95 36 4 420 SD 771 25 M36X2 25 36 98 41 7 SD 771 25 16 M36X2 25 37 110 41 7 414 1 25 16 25,4 SD 771 30 16 M42X2 30 39 1 50 8,7 280 SD 771 30 20 M42X2 30 41 8 50 8,7 1 1/4 32 20 31,8 250 SD 771 38 20 M52X2 38 43 131 60 SD 771 38 24 1 1/2 40 24 38,1 M52X2 38 44 138 60 250 SD 772 Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y X S/P G (bars) SD 772 20 M30X2 20 67 9 29 36 4 420 SD 772 25 M36X2 25 66 8 30 41 7 SD 772 25 16 M36X2 25 81 154 33 41 7 414 1 25 16 25,4 SD 772 30 16 M42X2 30 81 154 33 50 8,7 280 SD 772 30 20 M42X2 30 99 187 39 50 8,7 1 1/4 32 20 31,8 250 SD 772 38 20 M52X2 38 100 188 40 60 SD 772 38 24 1 1/2 40 24 38,1 M52X2 38 116 210 44 60 250 SD 773 FEMALE METRIC 24 CONE O-RING 45 SWEPT ELBOW HEAVY SERIES FEMALE METRIC 24 CONE O-RING 90 SWEPT ELBOW HEAVY SERIES Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y X S/P G (bars) SD 773 20 M30X2 20 55 117 60 36 4 420 SD 773 25 M36X2 25 55 117 60 41 7 SD 773 25 16 M36X2 25 71 144 71 41 7 414 1 25 16 25,4 SD 773 30 16 M42X2 30 71 144 71 50 8,7 280 SD 773 30 20 M42X2 30 90 177 85 50 8,7 1 1/4 32 20 31,8 250 SD 773 38 20 M52X2 38 90 177 86 60 SD 773 38 24 1 1/2 40 24 38,1 M52X2 38 107 201 98 60 250
Swage Fittings Catalogue - 55 Metric heavy series SD type insert SC 631 SC 771 SC 772 SC 631 Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y S/P G (bars) SC 631 20 M30X2 20 34 85 30 16 420 SC 631 25 M36X2 25 38 89 36 18 SC 631 25 16 M36X2 25 40 97 36 18 380 1 25 16 25,4 SC 631 30 16 M42X2 30 44 101 46 20 280 SC 631 30 20 M42X2 30 47 113 46 20 1 1/4 32 20 31,8 250 SC 631 38 20 M52X2 38 51 117 55 20 SC 631 38 24 1 1/2 40 24 38,1 m52x2 38 53 135 55 22 250 SC 771 Part Hose inner diameter ThreadTube Dimensions (mm) N inch DN Dash mm F mm W Y S/P G O RING (bars) SC 771 20 20 37 88 16,3x2,4 M30X2 36 4 420 SC 771 25 M36X2 25 39 90 46 7 20,3x2,4 SC 771 25 16 M36X2 25 41 97 46 7 22x2 380 1 25 16 25,4 SC 771 30 16 M42X2 30 42 98 50 8,7 25,3x2,4 280 SC771 30 20 M42X2 30 43 109 50 8,7 25,3x2,4 1 1/4 32 20 31,8 250 SC771 38 20 M52X2 38 48 115 60 33,3x2,4 SC771 38 24 1 1/2 40 24 38,1 M52X2 38 51 133 60 33,3x2,4 250 SC 772 MALE METRIC 24 CONE - HEAVY SERIES FEMALE METRIC 24 CONE 0-RING HEAVY SERIES FEMALE METRIC 24 CONE O-RING 45 SWEPT ELBOW HEAVY SERIES Part Hose inner diameter ThreadTube Dimensions (mm) N inch DN Dash mm F mm W Y X S/P G O RING (bars) SC772 20 20 65 116 27 36 4 16,3x2,4 M30X2 420 SC772 25 M36X2 25 66 117 28 46 7 20,3x2,4 SC772 25 16 25 83 140 34 46 7 22x2 380 1 25 16 25,4 M36X2 SC772 30 16 M42X2 30 82 138 32 50 8,7 25,3x2,4 280 SC772 30 20 30 100 166 40 50 8,7 25,3x2,4 1 1/4 32 20 31,8 M42X2 250 SC772 38 20 M52X2 38 97 164 38 60 33,3x2,4 SC772 38 24 1 1/2 40 24 38,1 M52X2 38 1 203 48 60 33,3x2,4 250 METRIC SC 773 SC 773 FEMALE METRIC 24 CONE O-RING 90 SWEPT ELBOW HEAVY SERIES Part Hose inner diameter ThreadTube Dimensions (mm) N inch DN Dash mm F mm W Y X S/P G O RING (bars) SC773 20 20 55 106 55 36 4 16,3x2,4 M30X2 420 SC773 25 M36X2 25 55 106 55 46 7 20,3x2,4 SC773 25 16 25 71 8 69 46 7 22x2 380 1 25 16 25,4 M36X2 SC773 30 16 M42X2 30 71 8 67 50 8,7 25,3x2,4 280 SC773 30 20 30 87 154 83 50 8,7 25,3x2,4 1 1/4 32 20 31,8 M42X2 250 SC773 38 20 M52X2 38 87 154 80 60 33,3x2,4 SC773 38 24 1 1/2 40 24 38,1 M52X2 38 105 188 100 60 33,3x2,4 250
56 - Swage Fittings Catalogue Metric French Gaz S type insert METRIC S 641 S 741 S 742 S 641 MALE METRIC FRENCH GAZ 24 CONE Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y D S/P G (bars) S 641 13 04 1/4 6 04 6,3 M20x1,5 13,25 26,7 55 13,25 22 NC S 641 13 05 5/16 8 05 7,9 M20x1,5 13,25 26,7 55 13,25 22 NC S 641 13 06 M20x1,5 13,25 26,7 57 13,25 22 14 3/8 10 06 9,5 S 641 17 06 M24x1,5 16,75 30,2 61 16,75 27 NC S 641 17 08 M24x1,5 16,75 30,7 64 16,75 27 14 1/2 08,7 S 641 21 08 M30x1,5 21,25 31,2 64 21,25 32 14 NC S 641 21 10 5/8 16 10 15,9 M30x1,5 21,25 31,2 67 21,25 32 14 NC S 641 21 M30x1,5 21,25 31,7 73 21,25 32 14 S 641 27 M36x1,5 21,25 31,7 73 26,75 36 14 NC S 641 33 16 1 25 16 25,4 M45x1,5 33,5 37,2 92 33,5 46 16 NC S 641 33 20 1 1/4 32 20 31,8 M45x1,5 33,5 38,2 99 33,5 46 16 NC S 741 FEMALE METRIC FRENCH GAZ 24 CONE Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y S/P G (bars) S 741 13 04 1/4 6 04 6,3 M20x1,5 13,25 23,852,3 24 4 NC S 741 13 05 5/16 8 05 7,9 M20x1,5 13,25 23,8 52,3 24 4 NC S 741 13 06 M20x1,5 13,25 23,854,3 24 4 3/8 10 06 9,5 S 741 17 06 M24x1,5 16,75 27 57,5 30 5 NC S 741 17 08 M24x1,5 16,75 27,360,3 30 5 1/2 08,7 S 741 21 08 M30x1,5 21,25 30 63 36 3 NC S 741 21 10 5/8 16 10 15,9 M30x1,5 21,25 30 66 36 3 NC S 741 21 M30x1,5 21,25 30,6 36 3 S 741 27 M36x1,5 26,75 33,674,5 41 7 NC S 741 33 16 1 25 16 25,4 M45x1,5 33,5 33,988,9 50 8,7 NC S 741 33 20 1 1/4 32 20 31,8 M45x1,5 33,5 34,595,5 50 8,7 NC S 742 FEMALE METRIC FRENCH GAZ 24 CONE 45 SWEPT ELBOW Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y X S/P G (bars) S 742 13 04 1/4 6 04 6,3 M20X1,5 13,25 41,5 70 21,3 24 4 NC S 742 13 05 5/16 8 05 7,9 M20X1,5 13,25 48,6 77,2 21,5 24 4 NC S 742 13 06 M20X1,5 13,25 54,3 84,7 21,9 24 4 3/8 10 06 9,5 S 742 17 06 M24X1,5 16,75 30 5 NC S 742 17 08 M24X1,5 16,75 65 97,7 23,8 30 5 1/2 08,7 S 742 21 08 M30X1,5 21,25 36 3 NC S 742 21 10 5/8 16 10 15,9 M30X1,5 21,25 76,5 1,6 30,5 36 3 NC S 742 21 M30X1,5 21,25 86,7 7,7 31,8 36 3 S 742 27 M36X1,5 26,75 90,4 131,4 36,7 41 7 NC S 742 33 16 1 25 16 25,4 M45X1,5 33,5 113 168,2 45,5 50 8,7 NC S 742 33 20 1 1/4 32 20 31,8 M45X1,5 33,5 50 8,7 NC
Swage Fittings Catalogue - 57 Metric French Gaz S type insert S 743 S 743 FEMALE METRIC FRENCH GAZ 24 CONE 90 SWEPT ELBOW Part Hose inner diameter Thread Dimensions Tube (mm) N inch DN Dash mm F mm W Y X S/P G (bars) S 743 13 04 1/4 6 04 6,3 M20X1,5 13,25 24 53 31 24 4 NC S 743 13 05 5/16 8 05 7,9 M20X1,5 13,25 31 59 34 24 4 NC S 743 13 06 M20X1,5 13,25 34 64 35 24 4 3/8 10 06 9,5 S 743 17 06 M24X1,5 16,75 34 64 37 30 5 NC S 743 17 08 M24X1,5 16,75 41 74 42 30 5 1/2 08,7 S 743 21 08 M30X1,5 21,25 39 72 47,3 36 3 NC S 743 21 10 5/8 16 10 15,9 M30X1,5 21,25 49,7 85,7 51 36 3 NC S 743 21 M30X1,5 21,25 54,9 95,9 59 36 3 S 743 27 M36X1,5 26,75 55,3 96,5 61,3 41 7 NC S 743 33 16 1 25 16 25,4 M45X1,5 33,5 54 109 75,4 50 8,7 NC S 743 33 20 1 1/4 32 20 31,8 M45X1,5 33,5 50 8,7 NC METRIC
58 - Swage Fittings Catalogue DIN 60 cone S type insert METRIC S 711 S 711 FEMALE DIN 60 CONE - CRIMPED NUT N inch DN Dash mm F W Y S/P G (bars) S 711 10 03 M10x1 19 44 14 3/16 5 03 4,8 S 711 03 Mx1,5 19 44 15 NC S 711 10 04 M10x1 19 47 14 S 711 04 Mx1,5 19 47 15 S 711 14 04 1/4 6 04 6,3 M14x1,5 18 47 17 NC S 711 16 04 M16x1,5 20 49 22 S 711 18 04 M18x1,5 20 49 22 S 711 14 05 M14x1,5 18 47 17 S 711 16 05 5/16 8 05 7,9 M16x1,5 20 49 22 NC S 711 18 05 M18x1,5 20 49 22 S 711 14 06 M14x1,5 18 49 17 S 711 16 06 M16x1,5 20 51 22 S 711 18 06 3/8 10 06 9,5 M18x1,5 20 51 22 NC S 711 20 06 M20x1,5 22 53 27 S 711 22 06 M22x1,5 22 53 27 S 711 18 08 M18x1,5 21 54 22 S 711 20 08 M20x1,5 23 56 27 S 711 22 08 1/2 08,7 M22x1,5 23 56 27 NC S 711 24 08 M24x1,5 23 56 30 S 711 26 08 M26x1,5 25 58 32 S 711 26 10 5/8 16 10 15,9 M26x1,5 25 61 32 NC S 711 26 M26x1,5 26 67 S 711 30 M30x1,5 26 67 36 8 NC S 711 38 16 1 25 16 25,4 M38x1,5 30 85 46 8 NC S 711 45 20 1 1/4 32 20 31,8 M45x1,5 34 95 50 5 NC
Swage Fittings Catalogue - 59 DIN 60 cone S type insert S 7 S 7 FEMALE DIN 60 CONE CRIMPED NUT 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 7 10 03 M10x1 36 61,5 14 14 3/16 5 03 4,8 S 7 03 Mx1,5 37,5 63 15,5 15 NC S 7 10 04 M10x1 39 67,5 15 14 S 7 04 Mx1,5 40 68,5 16,5 15 S 7 14 04 1/4 6 04 6,3 M14x1,5 40 68,5 16,5 17 NC S 7 16 04 M16x1,5 42,5 71 18,5 22 S 7 18 04 M18x1,5 42,5 71 18,5 22 S 7 14 05 M14x1,5 48 76,5 18 17 S 7 16 05 5/16 8 05 7,9 M16x1,5 49,5 78 19,5 22 NC S 7 18 05 M18x1,5 49,5 78 19,5 22 S 7 14 06 M14x1,5 53 83,5 19 17 S 7 16 06 M16x1,5 53,5 84 19,5 22 S 7 18 06 3/8 10 06 9,5 M18x1,5 53,5 84 19,5 22 NC S 7 20 06 M20x1,5 56,5 87 22,5 27 S 7 22 06 M22x1,5 56,5 87 22,5 27 S 7 18 08 M18x1,5 62,5 95,5 22 1/2 08,7 S 7 20 08 M20x1,5 64 97 24,5 27 NC S 7 22 08 M22x1,5 64 97 24,5 27 S 7 24 08 1/2 08,7 M24x1,5 65 98 25,5 30 NC S 7 26 08 M26x1,5 67,5 101 28 32 S 7 26 10 5/8 16 10 15,9 M26x1,5 81 117 29 32 NC S 7 26 M26x1,5 88,5 130 32 S 7 30 M30x1,5 91 132 38,5 36 8 NC S 7 38 16 1 25 16 25,4 M38x1,5 114 169 46 46 8 NC S 7 45 20 1 1/4 32 20 31,8 M45x1,5 138 199 54 50 5 NC METRIC
60 - Swage Fittings Catalogue DIN 60 cone S type insert METRIC S 713 S 713 FEMALE DIN 60 CONE CRIMPED NUT 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 713 10 03 M10X1 21 47 25 14 3/16 5 03 4,8 S 713 03 MX1,5 21 47 28 15 NC S 713 10 04 M10X1 24 52 16 14 S 713 04 MX1,5 24 52 28 15 S 713 14 04 1/4 6 04 6,3 M14X1,5 24 52 28 17 NC S 713 16 04 M16X1,5 24 52 31 22 S 713 18 04 M18X1,5 24 52 31 22 S 713 14 05 M14X1,5 31 59 31,5 17 S 713 16 05 5/16 8 05 7,9 M16X1,5 31 59 33,5 22 NC S 713 18 05 M18X1,5 31 59 33,5 22 S 713 14 06 M14X1,5 34 64 35,5 17 S 713 16 06 M16X1,5 34 64 40,5 22 S 713 18 06 3/8 10 06 9,5 M18X1,5 34 64 40,5 22 NC S 713 20 06 M20X1,5 34 64 40,5 27 S 713 22 06 M22X1,5 34 64 40,5 27 S 713 18 08 M18X1,5 41 74 42 22 S 713 20 08 M20X1,5 41 74 44 27 S 713 22 08 1/2 08,7 M22X1,5 41 74 44 27 NC S 713 24 08 M24X1,5 41 74 45,5 30 S 713 26 08 M26X1,5 41 74 49,5 32 S 713 26 10 5/8 16 10 15,9 M26X1,5 49 85 54,5 32 NC S 713 26 M26X1,5 58 99 32 S 713 30 M30X1,5 58 99 65 36 8 NC S 713 38 16 1 25 16 25,4 M38X1,5 74 9 79 46 8 NC S 713 45 20 1 1/4 32 20 31,8 M45X1,5 92 179 89 50 5 NC
Swage Fittings Catalogue - 61 DIN 24 /60 cone S type insert S 781 S 782 S 783 S 781 FEMALE DIN 24 /60 CONE SLIP-ON NUT N inch DN Dash mm F W X S/P G (bars) S 781 08 04 1/4 6 04 6,3 M14x1,5 20 48 17 250 S 781 10 05 5/16 8 05 7,9 M16x1,5 20 48 19 250 S 781 06 3/8 10 06 9,5 M18x1,5 20 50 22 250 S 781 15 08 1/2 08,7 M22x1,5 21 54 27 250 S 781 18 10 5/8 16 10 15,9 M26x1,5 23 58 32 160 S 782 FEMALE DIN 24 /60 CONE SLIP-ON NUT 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 782 08 04 1/4 6 04 6,3 M14x1,5 35 63 13 17 250 S 782 10 05 5/16 8 05 7,9 M16x1,5 37 65 15 19 250 S 782 06 3/8 10 06 9,5 M18x1,5 39 69 15 22 250 S 782 15 08 1/2 08,7 M22x1,5 45 78 17 27 250 S 782 18 10 5/8 16 10 15,9 M26x1,5 52 87 20 32 160 S 783 FEMALE DIN 24 /60 CONE SLIP-ON NUT 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 783 08 04 1/4 6 04 6,3 M14X1,5 29 57 27 17 250 S 783 10 05 5/16 8 05 7,9 M16X1,5 31 59 30 19 250 S 783 06 3/8 10 06 9,5 M18X1,5 31 61 30 22 250 S 783 15 08 1/2 08,7 M22X1,5 37 70 36 27 250 S 783 18 10 5/8 16 10 15,9 M26X1,5 45 81 42 32 160 METRIC
62 - Swage Fittings Catalogue BSP 60 cone S type insert B.S.P S 311 S 311 MALE BSPP 60 CONE N inch DN Dash mm F W Y S/P G S311 02 03 1/8-28 20 45 14 8 3/16 5 03 4,8 S311 04 03 1/4-19 24 49 19 11 S311 02 04 1/8-28 20 48 14 8 S311 04 04 1/4-19 25 53 19 11 1/4 6 04 6,3 S311 06 04 3/8-19 27 55 22 13 S311 08 04 1/2-14 32 60 27 14 S311 04 05 1/4-19 25 53 19 11 S311 06 05 5/16 8 05 7,9 3/8-19 27 55 22 13 S311 08 05 1/2-14 32 60 27 11 S311 04 06 1/4-19 25 55 19 14 S311 06 06 3/8 10 06 9,5 3/8-19 27 58 22 13 S311 08 06 1/2-14 32 62 27 14 S311 06 08 3/8-19 28 61 22 13 S311 08 08 1/2-14 33 66 27 14 1/2 08,7 S311 10 08 5/8-14 35 68 30 16 S311 08 3/4-14 36 69 32 17 S311 08 10 1/2-14 33 69 27 14 S311 10 10 5/8 16 10 15,9 5/8-14 35 71 30 16 S311 10 3/4-14 38 72 32 17 S311 08 1/2-14 34 74 27 14 S311 10 5/8-14 36 76 30 14 S311 3/4-14 37 77 32 17 S311 16 1-11 42 82 41 19 S311 16 3/4-14 38 89 32 17 S311 16 16 1 25 16 25,4 1-11 43 94 41 19 S311 20 16 1 1/4-11 46 97 50 21,5 S311 20 20 1 1/4-11 47 105 50 21,5 1 1/4 32 20 31,8 S311 24 20 1 1/2-11 50 108 55 21,5 S311 24 24 1 1/2-11 50 115 55 21,5 1 1/2 40 24 38,1 S311 32 24 2-11 55 119 70 26 S311 32 32 2 50 32 50,8 2-11 56 6 70 26 (bars) 415 450 450 415 280 210 185 165
Swage Fittings Catalogue - 63 BSP 60 cone S type insert S 471 S 471 FEMALE BSP 60 CONE N inch DN Dash mm F W Y G S/P S 471 02 03 1/8-28 16 41 4,3 14 3/16 5 03 4,8 S 471 04 03 1/4-19 19 44 4,1 19 S 471 02 04 1/8-28 17 45 4,3 14 S 471 04 04 1/4-19 19 47 4,1 19 1/4 6 04 6,3 S 471 06 04 3/8-19 22 50 5,8 22 S 471 08 04 1/2-14 23 51 6,5 27 S 471 04 05 1/4-19 19 47 4,1 19 S 471 06 05 5/16 8 05 7,9 3/8-19 22 50 5,8 22 S 471 08 05 1/2-14 23 51 6,5 27 S 471 04 06 1/4-19 19 49 4,1 19 S 471 06 06 3/8 10 06 9,5 3/8-19 21 51 5,8 22 S 471 08 06 1/2-14 23 54 6,5 27 S 471 06 08 3/8-19 22 56 5,8 22 S 471 08 08 1/2-14 23 56 6,5 27 1/2 08,7 S 471 10 08 5/8-14 24 57 9,3 30 S 471 08 3/4-14 27 60 8,6 32 S 471 08 10 1/2-14 23 59 6,5 27 S 471 10 10 5/8 16 10 15,9 5/8-14 23 59 9,3 30 S 471 10 3/4-14 27 63 8,6 32 S 471 08 1/2 14 24 65 6,5 27 S471 10 5/8-14 24 64 9,3 30 S 471 3/4-14 27 67 8,6 32 S 471 16 1-11 30 70 10,5 41 S 471 16 3/4-14 28 79 8,6 32 S 471 16 16 1 25 16 25,4 1-11 30 81 10,5 41 S 471 20 16 1 1/4-11 35 86 10 50 S 471 20 20 1 1/4-11 34 92 10 50 1 1/4 32 20 31,8 S 471 24 20 1 1/2-11 36 93 55 S 471 24 24 1 1/2-11 34 99 55 1 1/2 40 24 38,1 S 471 32 24 2-11 39 103 16 70 S 471 32 32 2 50 32 50,8 2-11 37 107 16 70 (bars) 415 450 450 415 280 210 185 165 B.S.P
64 - Swage Fittings Catalogue BSP 60 cone S type insert B.S.P S 472 S 472 FEMALE BSP 60 CONE 45 SWEPT ELBOW N inch DN Dash mm F W Y X G S/P (bars) S 472 02 03 1/8-28 33 58 14 4,3 14 3/16 5 03 4,8 S 472 04 03 1/4-19 35 60 16 4,1 19 415 S 472 02 04 1/8-28 36 64 16 4,3 14 S 472 04 04 1/4-19 37 65 16 4,1 19 1/4 6 04 6,3 S 472 06 04 3/8-19 40 68 19 19 22 450 S 472 08 04 1/2-14 42 70 21 6,5 27 S 472 04 05 1/4-19 39 67 18 5,1 19 S 472 06 05 5/16 8 05 7,9 3/8-19 41 69 19 5,8 22 S 472 08 05 1/2-14 43 71 21 6,5 27 S 472 04 06 1/4-19 41 72 18 4,1 19 S 472 06 06 3/8 10 06 9,5 3/8-19 42 73 19 5,8 22 450 S 472 08 06 1/2-14 44 75 21 6,5 27 S 472 06 08 3/8-19 49 82 22 5,8 22 S 472 08 08 1/2-14 49 82 22 6,5 27 1/2 08,7 S 472 10 08 5/8-14 49 82 22 9,3 30 415 S 472 08 3/4-14 53 86 26 8,6 32 S 472 08 10 1/2-14 57 93 26 6,5 27 S 472 10 10 5/8 16 10 15,9 5/8-14 54 90 24 9,3 30 S 472 10 3/4-14 57 93 26 8,6 32 S 472 08 1/2-14 68 108 30 6,5 27 S 472 10 5/8-14 66 106 28 9,3 30 S 472 3/4-14 66 106 28 8,6 32 S 472 16 1-11 68 108 30 11 41 S 472 16 3/4-14 87 138 38 8,6 32 S 472 16 16 1 25 16 25,4 1-11 84 135 36 11 41 280 S 472 20 16 1 1/4-11 85 136 37 10 50 S 472 20 20 1 1/4-11 100 157 43 10 50 1 1/4 32 20 31,8 S 472 24 20 1 1/2-11 100 157 43 55 S 472 24 24 1 1/2-11 116 180 49 55 1 1/2 40 24 38,1 S 472 32 24 2-11 116 180 49 16 70 210 185 S 472 32 32 2 50 32 50,8 2-11 150 220 62 16 70 165
Swage Fittings Catalogue - 65 BSP 60 cone S type insert S 473 S 473 FEMALE BSP 60 CONE 45 SWEPT ELBOW N inch DN Dash mm F W Y X G S/P (bars) S473 02 03 1/8-28 21 46 23 4,3 14 3/16 5 03 4,8 S473 04 03 1/4-19 21 46 26 4,1 19 415 S473 02 04 1/8-28 26 54 28 4,3 14 S473 04 04 1/4-19 26 54 28 4,1 19 1/4 6 04 6,3 S473 06 04 3/8-19 26 54 32 5,8 22 450 S473 08 04 1/2-14 26 54 36 6,5 27 S473 04 05 1/4-19 28 56 31 4,1 19 S473 06 05 5/16 8 05 7,9 3/8-19 28 56 34 5,8 22 S473 08 05 1/2-14 28 56 37 6,5 27 S473 04 06 1/4-19 31 61 34 4,1 19 S473 06 06 3/8 10 06 9,5 3/8-19 31 61 35 5,8 22 450 S473 08 06 1/2-14 31 61 38 6,5 27 S473 06 08 3/8-19 37 70 42 5,8 22 S473 08 08 1/2-14 37 70 42 6,5 27 1/2 08,7 S473 10 08 5/8-14 37 70 43 9,3 30 415 S473 08 3/4-14 37 70 48 8,6 32 S473 08 10 1/2-14 45 80 50 6,5 27 S473 10 10 5/8 16 10 15,9 5/8-14 45 80 46 9,3 30 S473 10 3/4-14 45 80 50 8,6 32 S473 08 1/2-14 54 95 59 6,5 27 S473 10 5/8-14 54 95 56 9,3 30 S473 3/4-14 54 95 56 8,6 32 S473 16 1-11 54 95 59 11 41 S473 16 3/4-14 70 1 75 8,6 32 S473 16 16 1 25 16 25,4 1-11 70 1 72 11 41 280 S473 20 16 1 1/4-11 70 1 73 10 50 S473 20 20 1 1/4-11 84 142 87 10 50 1 1/4 32 20 31,8 S473 24 20 1 1/2-11 84 142 87 55 S473 24 24 1 1/2-11 100 165 100 55 1 1/2 40 24 38,1 S473 32 24 2-11 100 165 100 16 70 210 185 S473 32 32 2 50 32 50,8 2-11 134 204 131 16 70 165 B.S.P
66 - Swage Fittings Catalogue BSP 60 cone S type insert B.S.P S 453 S 463 S 462 S 461 S 461 FEMALE BSP 60 CONE SLIP-ON NUT N inch DN Dash mm F W Y S/P G (bars) S 461 04 04 1/4 6 04 6,3 1/4-19 19,5 48 19 4,1 S 461 06 05 5/16 8 05 7,9 3/8-19 22 50,5 22 6 S 461 06 06 3/8 10 06 9,5 3/8-19 22 52,5 22 6 S 461 08 08 1/2 08,7 1/2-14 24,3 57,3 27 6,5 315 FEMALE BSP 60 CONE S 462 SLIP-ON NUT 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 462 04 04 1/4 6 04 6,3 1/4-19 37 65,5 13 19 4,1 S 462 06 05 5/16 8 05 7,9 3/8-19 46 74,5 15,5 22 6 S 462 06 06 3/8 10 06 9,5 3/8-19 50 80,5 16 22 6 S 462 08 08 1/2 08,7 1/2-14 59 92 20 27 6,5 315 S 463 FEMALE BSP 60 CONE SLIP-ON NUT 90 SWEPT ELBOW N inch DN Dash mm F W Y XX S/P G (bars) S 463 04 04 1/4 6 04 6,3 1/4-19 24 52 23,5 4,1 19 S 463 06 05 5/16 8 05 7,9 3/8-19 31 59 28,5 6 22 S 463 06 06 3/8 10 06 9,5 3/8-19 34 64 31,5 6 22 S 463 08 08 1/2 08,7 1/2-14 41 74 37,5 6,5 27 315 S 453 FEMALE BSP 60 CONE 90 COMPACT ELBOW N inch DN Dash mm F W Y XX S/P S/P1 G (bars) S 453 04 04 1/4 6 04 6,3 1/4-19 18 46 23 3,6 19 17 450 S 453 06 06 3/8 10 06 9,5 3/8-19 21 52 26 5,5 22 22 450 S 453 08 08 1/2 08,7 1/2-14 24 57 28 5,7 27 25 415
Swage Fittings Catalogue - 67 BSP 60 cone S type insert S 481 S 482 S 481 FEMALE BSP 60 CONE O-RING - CRIMPED NUT N inch DN Dash mm F W Y S/P G (bars) S 481 04 04 1/4-19 22 50 19 4,5 1/4 6 04 6,3 S 481 06 04 3/8-19 24 52 22 5,8 450 S 481 06 05 5/16 8 05 7,9 3/8-19 24 52 22 5,8 S 481 06 06 3/8-19 24 54 5,8 3/8 10 06 9,5 S 481 08 06 1/2-14 26 56 27 6,5 450 S 481 08 08 1/2-14 26 59 6,5 1/2 08,7 S 481 10 08 5/8-14 26 59 30 9,3 415 S 481 10 10 5/8-14 25 61 30 9,3 5/8 16 10 15,9 S 481 10 3/4-14 28 64 32 8,6 S 481 3/4-14 28 68 32 8,6 S 481 16 1-11 32 73 41 10 280 S 481 16 16 1-11 32 83 10 1 25 16 25,4 S 481 20 16 1 1/4-11 37 88 50 10 280 S 481 20 20 1 1/4 32 20 31,8 1 1/4-11 36 94 50 10 210 S 481 24 24 S 481 32 32 1 1/2 2 40 50 24 32 38,1 50,8 1 1/2-11 2-11 38 40 102 110 55 70 16 185 165 S 482 FEMALE BSP 60 CONE O-RING - CRIMPED NUT 45 SWEPT ELBOW N inch DN Dash mm F W Y X G S/P (bars) S 482 04 04 1/4-19 35 63 13 4,5 19 1/4 6 04 6,3 S 482 06 04 3/8-19 37 65 15 5,8 22 450 S 482 06 05 5/16 8 05 7,9 3/8-19 38 66 15 5,8 22 S 482 06 06 3/8-19 39 69 5,8 22 3/8 10 06 9,5 S 482 08 06 1/2-14 41 71 18 6,5 27 1/2-14 45 78 6,5 27 1/2 08,7 S 482 10 08 5/8-14 51 84 24 9,3 30 5/8-14 55 91 9,3 30 5/8 16 10 15,9 S 482 10 3/4-14 58 94 27 8,6 32 450 415 S 482 3/4-14 66 107 8,6 32 S 482 16 1-11 69 110 32 10 41 280 S 482 16 16 1-11 85 136 10 41 1 25 16 25,4 S 482 20 16 1 1/4-11 86 137 38 10 50 280 S 482 20 20 1 1/4 32 20 31,8 1 1/4-11 99 157 43 10 50 210 S 482 24 24 1 1/2 40 24 38,1 1 1/2-11 118 182 51 55 185 S 482 32 32 2 50 32 50,8 2-11 153 223 65 16 70 165 B.S.P
68 - Swage Fittings Catalogue BSP 60 cone S type insert B.S.P S 483 S 483 FEMALE BSP 60 CONE O-RING - CRIMPED NUT 90 SWEPT ELBOW N inch DN Dash mm F W Y X G S/P (bars) S 483 04 04 1/4-19 29 57 27 4,1 19 1/4 6 04 6,3 S 483 06 04 3/8-19 29 57 29 5,8 22 450 S 483 06 05 5/16 8 05 7,9 3/8-19 29 57 29 5,8 22 S 483 06 06 3/8-19 30 61 5,8 22 3/8 10 06 9,5 S 483 08 06 1/2-14 30 61 33 6,5 27 1/2-14 37 70 6,5 27 1/2 08,7 S 483 10 08 5/8-14 37 70 45 9,3 30 S 483 10 10 5/8-14 44 80 48 9,3 30 5/8 16 10 15,9 S 483 10 3/4-14 44 80 51 8,6 32 450 415 S 483 3/4-14 54 94 57 8,6 32 S 483 16 1-11 54 94 61 10 41 280 S 483 16 16 1-11 70 1 10 41 1 25 16 25,4 S 483 20 16 1 1/4-11 70 1 76 10 50 280 S 483 20 20 1 1/4 32 20 31,8 1 1/4-11 84 142 88 10 50 210 S 483 24 24 1 1/2 40 24 38,1 1 1/2-11 100 165 104 55 185 S 483 32 32 2 50 32 50,8 2-11 134 204 137 16 70 165
Swage Fittings Catalogue - 69 BSP 60 cone SD type insert SD 483 SD 482 SD 481 SD 311 SD 311 MALE BSPP 60 CONE N inch DN Dash mm F W Y S/P G (bars) SD 311 3/4-14 35 97 32 17 420 SD 311 16 16 1-11 41 114 19 1 25 16 25,4 41 414 SD 311 20 16 1 1/4-11 44 117 50 21,5 SD 311 20 20 1 1/4 32 20 31,8 1 1/4-11 46 134 50 21,5 414 SD 311 24 24 1 1/2 40 24 38,1 1 1/2-11 49 143 55 21,5 345 SD 311 32 32 2 50 32 50,8 2-11 56 154 70 26 345 SD 481 FEMALE BSP 60 CONE 0-RING - THRUST-WIRE NUT N inch DN Dash mm F W Y S/P G (bars) SD 481 3/4-14 25 87 32 6,5 420 SD 481 16 16 1-11 30 103 41 8 1 25 16 25,4 SD 481 20 16 1 1/4-11 33 106 50 9,5 414 SD 481 20 20 1 1/4 32 20 31,8 1 1/4-11 35 2 50 9,5 414 SD 481 24 24 1 1/2 40 24 38,1 1 1/2-11 36 130 60 10 345 SD 481 32 32 2 50 32 50,8 2-11 40 138 75 13,5 345 FEMALE BSP 60 CONE SD 482 0-RING - THRUST-WIRE NUT - 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) SD 482 3/4-14 68 130 32 32 6,5 420 SD 482 16 16 1-11 86 159 41 1 25 16 25,4 39 8 414 SD 482 20 16 1 1/4-11 88 161 41 50 9,5 SD 482 20 20 1 1/4 32 20 31,8 1 1/4-11 107 195 47 50 9,5 414 SD 482 24 24 1 1/2 40 24 38,1 1 1/2-11 6 220 55 60 10 345 SD 482 32 32 2 50 32 50,8 2-11 160 258 66 75 13,5 345 FEMALE BSP 60 CONE SD 483 0-RING - THRUST-WIRE NUT - 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) SD 483 3/4-14 55 117 63 32 6,5 420 SD 483 16 16 1-11 71 144 41 1 25 16 25,4 79 8 414 SD 483 20 16 1 1/4-11 71 144 81 50 9,5 SD 483 20 20 1 1/4 32 20 31,8 1 1/4-11 90 177 96 50 9,5 414 SD 483 24 24 1 1/2 40 24 38,1 1 1/2-11 107 201 113 60 10 345 SD 483 32 32 2 50 32 50,8 2-11 142 240 140 75 13,5 345 B.S.P
70 - Swage Fittings Catalogue BSP 60 cone SC type insert B.S.P SC 311 SC 481 SC 311 N inch DN Dash mm F W Y S/P G (bars) SC 311 3/4-14 38 89 32 17 420 SC 311 16 1-11 43 94 41 19 420 SC 311 16 16 1 25 16 25,4 1-11 45 101 41 19 420 SC 311 20 16 1 25 16 25,4 1 1/4-11 48 104 50 21,5 345 SC 311 20 20 1 1/4 32 20 31,8 1 1/4-11 50 117 50 21,5 345 SC 311 24 20 1 1/4 32 20 31,8 1 1/2-11 53 0 55 21,5 345 SC 311 24 24 1 1/2 40 24 38,1 1 1/2-11 55 138 55 21,5 345 SC 311 32 32 2 50 32 50,8 2-11 63 159 70 26 345 SC 481 MALE BSPP 60 CONE FEMALE BSP 60 CONE 0-RING - THRUST-WIRE NUT N inch DN Dash mm F W Y S/P G O RING (bars) SC 481 29 80 32 8,6 17x1,5 3/4-14 420 SC 481 16 1-11 32 83 41 10 22x1,5 SC 481 16 16 34 90 41 10 22x1,5 420 1 25 16 25,4 1-11 SC 481 20 16 1 1/4-11 37 93 50 10 28,3x1,78 345 SC481 20 20 39 106 50 10 28,3x1,78 1 1/4 32 20 31,8 1 1/4-11 345 SC481 24 20 1 1/2-11 41 107 60 33,05x1,78 SC481 24 24 1 1/2 40 24 38,1 1 1/2-11 43 5 60 33,05x1,78 345 SC481 32 32 2 50 32 50,8 2-11 47 143 75 16 44,17x1,78 345 SC 482 SC 482 FEMALE BSP 60 CONE 0-RING - THRUST-WIRE NUT - 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G O RING (bars) SC 482 67 118 29 17X1,5 3/4-14 32 8,6 420 SC 482 16 1-11 67 118 29 41 10 22X1,5 SC 482 16 16 1-11 86 142 36 41 10 22X1,5 420 1 25 16 25,4 SC482 20 16 1 1/4-11 86 142 36 50 10 28,3X1,78 345 SC482 20 20 1 1/4-11 103 169 43 50 10 28,3X1,78 1 1/4 32 20 31,8 345 SC482 24 20 1 1/2-11 103 169 43 60 33,05X1,78 SC482 24 24 1 1/2 40 24 38,1 1 1/2-11 3 206 51 60 33,05X1,78 345 SC482 32 32 2 50 32 50,8 2-11 160 257 65 75 16 44,17X1,78 345 SC 483 SC 483 FEMALE BSP 60 CONE 0-RING - THRUST-WIRE NUT - 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G O RING (bars) SC 483 55 106 57 17X1,5 3/4-14 32 8,6 420 SC 483 16 1-11 55 106 57 41 10 22X1,5 SC 483 16 16 1-11 71 8 72 41 10 22X1,5 420 1 25 16 25,4 SC483 20 16 1 1/4-11 71 8 72 50 10 28,3X1,78 345 SC483 20 20 1 1/4-11 87 154 88 50 10 28,3X1,78 1 1/4 32 20 31,8 345 SC483 24 20 1 1/2-11 87 154 88 60 33,05X1,78 SC483 24 24 1 1/2 40 24 38,1 1 1/2-11 105 188 104 60 33,05X1,78 345 SC483 32 32 2 50 32 50,8 2-11 140 237 137 75 16 44,17X1,78 345
Swage Fittings Catalogue - 71 BSP flat seat S type insert S 331 S 331 MALE BSP FLAT SEAT N inch DN Dash mm F W Y S/P G (bars) S 331 04 04 1/4-19 25 53 19 11 400 1/4 6 04 6,3 S 331 06 04 3/8-19 27 55 22 13 400 S 331 06 05 5/16 8 05 7,9 3/8-19 27 55 22 13 400 S 331 06 06 3/8-19 27 58 13 400 3/8 10 06 9,5 S 331 08 06 1/2-14 32 62 27 14 S 331 08 08 1/2-14 33 66 27 14 S 331 10 08 1/2 08,7 5/8-14 35 68 30 16 S 331 08 3/4-14 36 69 32 17 315 S 331 10 10 5/8-14 35 71 30 16 5/8 16 10 15,9 S 331 10 3/4-14 36 72 32 17 315 S 331 3/4-14 37 77 32 17 315 S 331 16 1-11 42 82 41 19 250 S 331 16 16 1 25 16 25,4 1-11 43 94 41 19 250 S 331 20 20 1 1/4 25 20 25,4 1 1/4-11 47 105 50 21,5 200 B.S.P S 421 S 421 FEMALE BSP FLAT SEAT N inch DN Dash mm F W Y S/P G (bars) S 421 04 04 1/4-19 15 43 19 7 1/4 6 04 6,3 S 421 06 04 3/8-19 18 46 22 9 S 421 06 05 5/16 8 05 7,9 3/8-19 18 46 22 9 S 421 06 06 3/8-19 17 47 9 3/8 10 06 9,5 S 421 08 06 1/2-14 19 49 27 10 315 S 421 08 08 1/2-14 19 52 27 10 315 S 421 10 08 1/2 08,7 5/8-14 21 54 30 11,5 315 S 421 08 3/4-14 23 56 32 250 S 421 10 10 5/8-14 20 56 30 11,5 315 5/8 16 10 15,9 S 421 10 3/4-14 23 59 32 250 S 421 3/4-14 22 63 32 250 S 421 16 1-11 25 65 41 14 200 S 421 16 16 1 25 16 25,4 1-11 25 76 41 14 200 S 421 20 20 1 1/4 25 20 25,4 1 1/4-11 28 90 50 15 160
72 - Swage Fittings Catalogue BSP taper S type insert B.S.P S 321 S 321 MALE BSP TAPER 60 CONE N inch DN Dash mm F W Y G S/P (bars) S 321 02 03 1/8-28 20 45 8 3/16 5 03 4,8 S 321 04 03 1/4-19 25 50 14 15 415 S 321 02 04 1/8-28 21 49 8 S 321 04 04 1/4 6 04 6,3 1/4-19 25 53 14 15 450 S 321 06 04 3/8-19 26 54 14 19 S 321 04 05 1/4-19 25 53 15 5/16 8 05 7,9 S 321 06 05 3/8-19 26 54 14 19 S 321 04 06 1/4-19 26 56 14 15 450 S 321 06 06 3/8 10 06 9,5 3/8-19 27 57 14 19 450 S 321 08 06 1/2-14 32 63 19 22 415 S 321 06 08 3/8-19 28 64 14 19 1/2 08,7 S 321 08 08 1/2-14 33 66 19 22 415 S 321 08 10 1/2-14 33 69 19 22 5/8 16 10 15,9 S 321 10 3/4-14 35 71 19 27 S 321 3/4-14 36 77 27 S 321 16 1-11 41 82 21 36 280 S 321 16 16 1-11 43 94 21 36 280 1 25 16 25,4 S 321 20 16 1 1/4-11 47 98 24 46 210 S 321 20 20 1 1/4 32 20 31,8 1 1/4-11 48 106 24 46 210 S 321 24 24 1 1/2 40 24 38,1 1 1/2-11 49 114 25 50 185 S 321 32 32 2 50 32 50,8 2-11 57 7 26 65 165 BSP taper SD type insert SD 321 SD 321 MALE BSP TAPER 60 CONE N inch DN Dash mm F W Y G S/P (bars) SD 321 3/4-14 34 96 27 19 420 SD 321 16 16 1 25 16 25,4 1-11 40 113 36 24 414 SD 321 20 20 1 1/4 32 20 31,8 1 1/4-11 47 135 46 24,5 414 SD 321 24 24 1 1/2 40 24 38,1 1 1/2-11 48 142 50 25 345 SD 321 32 32 2 50 32 50,8 2-11 57 155 65 26 345 BSP taper SC type insert SC 321 SC 321 MALE BSP TAPER 60 CONE N inch DN Dash mm F W Y G S/P (bars) SC 321 3/4-14 37 88 27 19 420 SC 321 16 16 1 25 16 25,4 1-11 44 101 36 21 380 SC 321 20 20 1 1/4 32 20 31,8 1 1/4-11 51 118 46 24 325 SC 321 24 24 1 1/2 40 24 38,1 1 1/2-11 54 137 50 25 290 SC 321 32 32 2 50 32 50,8 2-11 64 160 65 26 250
Swage Fittings Catalogue - 73 JIC S type insert S 111 S 111 MALE JIC 74 CONE N inch DN Dash mm F W Y S/P G (bars) S 111 07 03 7/16-20 26,3 52 14 3/16 5 03 4,8 S 111 08 03 1/2-20 26,3 52 14 14 415 S 111 07 04 7/16-20 26,5 55 14 S 111 08 04 1/4 6 04 6,3 1/2-20 26,5 55 14 14 450 S 111 09 04 9/16-18 26,5 55 15 14 S 111 08 05 1/2-20 26,5 55 14 14 S 111 09 05 5/16 8 05 7,9 9/16-18 26,5 55 15 14 S 111 05 3/4-16 30,2 58,7 19 17 S 111 09 06 9/16-18 26,5 57 15 14 450 S 111 06 3/8 10 06 9,5 3/4-16 30,2 60,5 19 17 415 S 111 14 06 7/8-14 34,2 64,7 24 19 S 111 08 3/4-16 31 64 19 17 415 S 111 14 08 1/2 08,7 7/8-14 35,5 68 24 19 S 111 17 08 1 1/16-38,5 71,5 27 22 S 111 14 10 7/8-14 35 71 24 19 5/8 16 10 15,9 S 111 17 10 1 1/16-38,5 74,5 27 22 S 111 14 7/8-14 36 77 27 22 S 111 17 1 1/16-39,5 80,5 27 23 S 111 19 1 3/16-41,5 82,5 32 23 280 S 111 21 1 5/16-42 83 36 23 280 S 111 17 16 1 1/16-41 96 32 22 S 111 21 16 1 25 16 25,4 1 5/16-42,7 97,7 36 23 280 S 111 26 16 1 5/8-46 101 46 24 S 111 26 20 1 5/8-46,5 107,5 24 210 1 1/4 32 20 31,8 S 111 30 20 1 7/8-51 1 50 28 140 S 111 30 24 1 1/2 40 24 38,1 1 7/8-51,2 1,7 50 28 140 S 111 40 32 2 50 32 50,8 2 1/2-62,2 138,2 65 34 105 J.I.C
74 - Swage Fittings Catalogue JIC S type insert J.I.C S 211 S 211 FEMALE JIC 74 CONE N inch DN Dash mm F W Y S/P G (bars) S 211 07 03 7/16-20 14,5 40,2 15 9 3/16 5 03 4,8 S 211 08 03 1/2-20 16,8 42,5 17 9,5 S 211 07 04 7/16-20 14,7 43,2 15 9 S 211 08 04 1/4 6 04 6,3 1/2-20 16 44,5 17 9,5 S 211 09 04 9/16-18 18 46,5 19 10 250 S 211 08 05 1/2-20 16 44,5 17 10 S 211 09 05 5/16 8 05 7,9 9/16-18 17 45,5 19 11 250 S 211 05 3/4-16 18,5 47 24 13 250 S 211 09 06 9/16-18 17 47,5 19 11 250 S 211 06 3/8 10 06 9,5 3/4-16 18,5 49 24 13 250 S 211 14 06 7/8-14 19,5 50 27 13 200 S 211 08 3/4-16 18,5 51,5 24 13 250 S 211 14 08 1/2 08,7 7/8-14 19,5 52,5 27 13 200 S 211 17 08 1 1/16-22,5 55,5 32 14,5 200 S 211 14 10 7/8-14 19,5 55,5 27 13 200 5/8 16 10 15,9 S 211 17 10 1 1/16-22,5 58,5 32 14,5 200 S 211 14 7/8-14 20,5 61,5 27 13 200 S 211 17 1 1/16-22 63 32 14,5 200 S 211 19 1 3/16-25,2 66,2 36 15 160 S 211 21 1 5/16-25,7 66,7 41 15,5 160 S 211 17 16 1 1/16-23,5 78,5 32 14,5 200 S 211 21 16 1 25 16 25,4 1 5/16-26 81 41 15,5 160 S 211 26 16 1 5/8-28,8 83,8 50 16 5 S 211 26 20 1 5/8-27,8 88,8 16 5 1 1/4 32 20 31,8 S 211 30 20 1 7/8-31 92 55 18,5 100 S 211 30 24 1 1/2 40 24 38,1 1 7/8-31,5 102 55 18,5 100 S 211 40 32 2 50 32 50,8 2 1/2-33,5 109,5 70 26 80
Swage Fittings Catalogue - 75 JIC S type insert S 2 S 2 FEMALE JIC 74 CONE 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 2 07 03 7/16-20 34,5 60,5 13 15 9 3/16 5 03 4,8 S 2 08 03 1/2-20 36 62 14,5 17 9,5 S 2 07 04 7/16-20 37 66 13,5 15 9 S 2 08 04 1/4 6 04 6,3 1/2-20 38 67 14,5 17 9,5 S 2 09 04 9/16-18 39,5 68 15,5 19 10 250 S 2 08 05 1/2-20 46 74,5 16 17 9,5 S 2 09 05 5/16 8 05 7,9 9/16-18 47,5 76 17,5 19 10 250 S 2 05 3/4-16 49,5 77,5 19 24 13 250 S 2 09 06 9/16-18 53,5 84 19,5 19 10 250 S 2 06 3/8 10 06 9,5 3/4-16 53,5 84 19,5 24 11 250 S 2 14 06 7/8-14 55 85,5 21 27 13 200 S 2 08 3/4-16 61,5 94,5 22 24 11 200 S 2 14 08 1/2 08,7 7/8-14 62,5 95,5 23 27 13 200 S 2 17 08 1 1/16-65 98 25,5 32 14,5 200 S 2 14 10 7/8-14 76 1 24 27 13 200 5/8 16 10 15,9 S 2 17 10 1 1/16-78,5 114,5 26 32 14,5 200 S 2 14 7/8-14 87 8 33,5 27 13 200 S 2 17 1 1/16-85,5 6,5 32 32 14,5 200 S 2 19 1 3/16-88,5 9,5 35 36 15 160 S 2 21 1 5/16-91 132 37,5 41 15,5 160 S 2 17 16 1 1/16-1 167,5 44,5 32 14,5 200 S 2 21 16 1 25 16 25,4 1 5/16-108 162,5 40 41 15,5 160 S 2 26 16 1 5/8-111 166 43 50 16 5 S 2 26 20 1 5/8-136 196,5 50 16 5 1 1/4 32 20 31,8 S 2 30 20 1 7/8-141 201,5 57 55 18,5 100 S 2 30 24 1 1/2 40 24 38,1 1 7/8-161 231 57 55 18,5 100 S 2 40 32 2 50 32 50,8 2 1/2-205,5 281 66,5 70 26 80 J.I.C
76 - Swage Fittings Catalogue JIC S type insert J.I.C S 213 S 216 S 213 FEMALE JIC 74 CONE 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 213 07 03 7/16-20 21 47 22 15 9 3/16 5 03 4,8 S 213 08 03 1/2-20 21 47 23 17 9,5 S 213 07 04 7/16-20 24 52 24 15 9 S 213 08 04 1/4 6 04 6,3 1/2-20 24 52 25 17 9,5 S 213 09 04 9/16-18 23,5 52 27 19 10 250 S 213 08 05 1/2-20 31 59 29 17 10 S 213 09 05 5/16 8 05 7,9 9/16-18 30,5 59 30,5 19 11 250 S 213 05 3/4-16 30,5 59 33,5 24 13 250 S 213 09 06 9/16-18 33,5 64 36,5 19 11 250 S 213 06 3/8 10 06 9,5 3/4-16 33,5 64 36 24 13 250 S 213 14 06 7/8-14 33,5 64 38,5 27 13 200 S 213 08 3/4-16 41 74 40,5 24 13 250 S 213 14 08 1/2 08,7 7/8-14 41 74 42 27 13 200 S 213 17 08 1 1/16-41 74 45,5 32 14,5 200 S 213 14 10 7/8-14 49 85 47 27 13 200 5/8 16 10 15,9 S 213 17 10 1 1/16-49 85 50,5 32 14,5 200 S 213 14 7/8-14 58 99 58 27 13 200 S 213 17 1 1/16-58 99 56,5 32 14,5 200 S 213 19 1 3/16-58 99 64 36 15 160 S 213 21 1 5/16-58 99 65 41 15,5 160 S 213 17 16 1 1/16-74 9 76 32 14,5 200 S 213 21 16 1 25 16 25,4 1 5/16-74 9 72 41 15,5 160 S 213 26 16 1 5/8-74 9 77 50 16 5 S 213 26 20 1 5/8-92 153 50 16 5 1 1/4 32 20 31,8 S 213 30 20 1 7/8-92 153 91 55 18,5 100 S 213 30 24 1 1/2 40 24 38,1 1 7/8-108 179 100 55 18,5 100 S 213 40 32 2 50 32 50,8 2 1/2-142 218 6 70 26 80 S 216 FEMALE JIC 74 CONE DOUBLE HEX N inch DN Dash mm F W Y S/P S/P1 G (bars) S 216 07 04 7/16-20 19 47,5 15 NC S 216 08 04 1/4 6 04 6,3 1/2-20 19 47,5 17 14 NC S 216 09 04 9/16-18 23 51,5 19 14 NC 250 S 216 09 05 5/16 8 05 7,9 9/16-18 23 51,5 19 14 NC 250 S 216 09 06 9/16-18 23 53,4 19 15 NC 250 3/8 10 06 9,5 S 216 06 3/4-16 23,5 54 24 19 NC 250 S 216 08 3/4-16 24,5 57,5 24 19 NC 250 1/2 08,7 S 216 14 08 7/8-14 25,5 58,5 27 22 NC 200 S 216 14 10 7/8-14 25,5 61,5 27 22 NC 200 5/8 16 10 15,9 S 216 17 10 1 1/16-28 64 32 27 NC 200 S 216 17 1 1/16-29 70 32 27 NC 200 S 216 21 16 1 25 16 25,4 1 5/16-35 90 41 32 NC 160
Swage Fittings Catalogue - 77 JIC SD type insert SD 111 SD 211 SD 2 SD 111 MALE JIC 74 CONE N inch DN Dash mm F W Y S/P G (bars) SD 111 17 1 1/16-38 99 27 23 SD 111 19 1 3/16-39 101 32 23 420 SD 111 21 1 5/16-41 102 36 23 SD 111 21 16 1 5/16-42 114 23 1 25 16 25,4 SD 111 26 16 1 5/8-45 117 46 24 414 SD 111 26 20 1 5/8-47 134 24 1 1/4 32 20 31,8 SD 111 30 20 1 7/8-51 139 50 28 414 SD 111 30 24 1 1/2 40 24 38,1 1 7/8-52 145 50 28 345 SD 111 40 32 2 50 32 50,8 2 1/2-63 160 65 34 345 SD 211 FEMALE JIC 74 CONE THRUST-WIRE NUT N inch DN Dash mm F W Y S/P G (bars) SD 211 17 1 1/16-20 82 32 14,5 SD 211 19 1 3/16-21,5 83 36 15 420 SD 211 21 1 5/16-22,5 84 41 15 SD 211 21 16 1 5/16-23,5 96 15 1 25 16 25,4 SD 211 26 16 1 5/8-28 101 50 16 414 SD 211 26 20 1 5/8-29 117 50 16 1 1/4 32 20 31,8 SD 211 30 20 1 7/8-29,5 117 60 18,5 414 SD 211 30 24 1 1/2 40 24 38,1 1 7/8-30 4 60 18,5 345 SD 211 40 32 2 50 32 50,8 2 1/2-37 135 75 24 345 SD 2 FEMALE JIC 74 CONE THRUST-WIRE NUT - 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) SD 2 17 1 1/16-64 6 28 32 14,5 SD 2 19 1 3/16-65 7 29 36 15 420 SD 2 21 1 5/16-68 130 32 41 15 SD 2 21 16 1 5/16-82 155 41 15 1 25 16 25,4 SD 2 26 16 1 5/8-84 157 37 50 16 414 SD 2 26 20 1 5/8-103 191 43 50 16 1 1/4 32 20 31,8 SD 2 30 20 1 7/8-103 191 43 60 18,5 414 SD 2 30 24 1 1/2 40 24 38,1 1 7/8-1 215 50 60 18,5 345 SD 2 40 32 2 50 32 50,8 2 1/2-158 256 65 75 24 345 J.I.C
J.I.C 78 - Swage Fittings Catalogue JIC SD type insert SD 213 SD 213 FEMALE JIC 74 CONE THRUST-WIRE NUT - 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) SD 213 17 1 1/16-55 117 58 32 14,5 SD 213 19 1 3/16-55 117 59 36 15 420 SD 213 21 1 5/16-55 117 63 41 15 SD 213 21 16 1 5/16-71 144 41 15 1 25 16 25,4 SD 213 26 16 1 5/8-71 144 76 50 16 414 SD 213 26 20 1 5/8-90 177 91 50 16 1 1/4 32 20 31,8 SD 213 30 20 1 7/8-90 177 91 60 18,5 414 SD 213 30 24 1 1/2 40 24 38,1 1 7/8-107 201 106 60 18,5 345 SD 213 40 32 2 50 32 50,8 2 1/2-140 240 139 75 24 345
Swage Fittings Catalogue - 79 JIC SC type insert SC 111 SC 111 MALE JIC 74 CONE N inch DN Dash mm F W Y S/P G (bars) SC 111 14 7/8-14 37 88 27 22 420 SC 111 17 1 1/16-40 91 27 23 420 SC 111 19 1 3/16-41,5 92,5 32 23 420 SC 111 21 1 5/16-43 94 36 23 380 SC 111 17 16 1 1/16-43 99,5 32 23 420 SC 111 21 16 1 25 16 25,4 1 5/16-45 101,5 36 23 380 SC 111 26 16 1 5/8-48 104,5 46 24 325 SC 111 21 20 1 5/16-48,5 115 41 23 380 SC 111 26 20 1 1/4 32 20 31,8 1 5/8-50,5 117 46 24 325 SC 111 30 20 1 7/8-55 1,5 50 28 290 SC 111 30 24 1 7/8-57 139,5 50 28 290 1 1/2 38 24 38,1 SC 111 40 24 2 1/2-65,5 148 65 34 250 SC 111 40 32 2 51 32 50,8 2 1/2-68,5 165 65 34 250 SC 211 SC 2 SC 211 FEMALE JIC 74 CONE N inch DN Dash mm F W Y S/P G (bars) SC 211 14 7/8-14 33 84 27 13 420 SC 211 17 1 1/16-34 85 32 14,5 420 SC 211 19 1 3/16-35,5 86,5 36 15 420 SC 211 21 1 5/16-38 89 41 15,5 380 SC 211 17 16 1 1/16-36,5 93 32 16 420 SC 211 21 16 1 25 16 25,4 1 5/16-39,5 96 41 15,5 380 SC 211 26 16 1 5/8-46 102,5 50 16 325 SC 211 21 20 1 5/16-45,5 1 41 15,5 380 SC 211 26 20 1 1/4 32 20 31,8 1 5/8-48 114,5 50 16 325 SC 211 30 20 1 7/8-51 117,5 60 18,5 290 SC 211 30 24 1 7/8-53 135,5 60 18,5 290 1 1/2 38 24 38,1 SC 211 40 24 2 1/2-66 148,5 75 26 250 SC 211 40 32 2 51 32 50,8 2 1/2-69 165,5 75 26 250 SC 2 FEMALE JIC 74 CONE 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) SC 2 14 7/8-14 66 117 28 27 13 420 SC 2 17 1 1/16-63 114 25 32 14,5 420 SC 2 19 1 3/16-63 114 25 36 15 420 SC 2 21 1 5/16-63 114 25 41 15,5 380 SC 2 17 16 1 1/16-85 141 35 32 14,5 420 SC 2 21 16 1 25 16 25,4 1 5/16-82 138 32 41 15,5 380 SC 2 26 16 1 5/8-82 138 32 50 16 325 SC 2 21 20 1 5/16-100 167 41 41 15,5 380 SC 2 26 20 1 1/4 32 20 31,8 1 5/8-98 164 38 50 16 325 SC 2 30 20 1 7/8-98 164 38 60 18,5 290 SC 2 30 24 1 7/8-118 201 46 60 18,5 290 1 1/2 38 24 38,1 SC 2 40 24 2 1/2-118 201 46 75 26 250 SC 2 40 32 2 51 32 50,8 2 1/2-157 253 62 75 26 250 J.I.C
J.I.C 80 - Swage Fittings Catalogue JIC SC type insert SC 213 SC 213 FEMALE JIC 74 CONE 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) SC 213 14 7/8-14 55 106 55 27 13 420 SC 213 17 1 1/16-55 106 52 32 14,5 420 SC 213 19 1 3/16-55 106 52 36 15 420 SC 213 21 1 5/16-55 106 52 41 15,5 380 SC 213 17 16 1 1/16-71 8 71 32 14,5 420 SC 213 21 16 1 25 16 25,4 1 5/16-71 8 67 41 15,5 380 SC 213 26 16 1 5/8-71 8 67 50 16 325 SC 213 21 20 1 5/16-87 154 84 41 15,5 380 SC 213 26 20 1 1/4 32 20 31,8 1 5/8-87 154 81 50 16 325 SC 213 30 20 1 7/8-87 154 81 60 18,5 290 SC 213 30 24 1 7/8-105 188 97 60 18,5 290 1 1/2 38 24 38,1 SC 213 40 24 2 1/2-105 188 97 75 26 250 SC 213 40 32 2 51 32 50,8 2 1/2-140 237 132 75 26 250
Swage Fittings Catalogue - 81 3000 psi SAE flange S type insert S 811 S 811 3000 PSI SAE J518 FLANGE STRAIGHT Part Hose inner diameter Collar N inch DN Dash mm inch S 811 08 08 1/2 1/2 08,7 S 811 08 3/4 S 811 08 10 1/2 5/8 16 10 15,9 S 811 10 3/4 S 811 08 1/2 S 811 3/4 S 811 16 1 S 811 16 3/4 S 811 16 16 1 25 16 25,4 1 S 811 20 16 1 1/4 S 811 16 20 1 S 811 20 20 1 1/4 32 20 31,8 1 1/4 S 811 24 20 1 1/2 S 811 24 24 1 1/2 1 1/2 40 24 38,1 S 811 32 24 2 S 811 32 32 2 2 50 32 50,8 S 811 40 32 2 1/2 Dimensions (mm) W 48,5 Y 81,5 D 30,2 52,5 85,5 38,1 46,5 82,5 30,2 52,5 88,5 38,1 36 77 30,2 53,5 94,5 38,1 59,5 100,5 44,5 61 116 38,1 60,5 115,5 44,5 65 0 50,8 61 2 44,5 65,5 6,5 50,8 70 130 60,3 70,5 141 60,3 77,5 147,5 71,4 77 153 71,4 77,5 153,5 84,1 (bars) 280 210 185 170 S 8 S 8 3000 PSI SAE J518 FLANGE 45 SWEPT ELBOW Part Hose inner diameter Collar N inch DN Dash mm inch S 8 08 08 1/2 1/2 08,7 S 8 08 3/4 S 8 08 10 1/2 5/8 16 10 15,9 S 8 10 3/4 S 8 08 1/2 S 8 3/4 S 8 16 1 S 8 16 3/4 S 8 16 16 1 25 16 25,4 1 S 8 20 16 1 1/4 S 8 16 20 1 S 8 20 20 1 1/4 32 20 31,8 1 1/4 S 8 24 20 1 1/2 S 8 24 24 1 1/2 1 1/2 40 24 38,1 S 8 32 24 2 S 8 32 32 2 2 50 32 50,8 S 8 40 32 2 1/2 W 62 66 70 79,5 84 86,5 90 103 Dimensions (mm) Y 95 99 102,5 115,5 5 7,5 132 158 107,5 162,5 108,5 163,5 130 191 136,5 197,5 136,5 197,5 162 232,5 164 234,5 210,5 286,5 224 299,5 X 22,5 27 23 27 31 33 36,5 35 39,5 40,5 46,5 53 53 58,5 60,5 71,5 78,35 D 30,2 38,1 30,2 38,1 30,2 38,1 44,5 38,1 44,5 50,8 44,5 50,8 60,3 60,3 71,4 71,4 84,1 (bars) 280 210 185 170 FLANGE
FLANGE 82 - Swage Fittings Catalogue 3000 psi SAE flange S type insert S 813 S 813 3000 PSI SAE J518 FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar N inch DN Dash mm inch S 813 08 08 1/2 1/2 08,7 S 813 08 3/4 S 813 08 10 1/2 5/8 16 10 15,9 S 813 10 3/4 S 813 08 1/2 S 813 3/4 S 813 16 1 S 813 16 3/4 S 813 16 16 1 25 16 25,4 1 S 813 20 16 1 1/4 S 813 16 20 1 S 813 20 20 1 1/4 32 20 31,8 1 1/4 S 813 24 20 1 1/2 S 813 24 24 1 1/2 1 1/2 40 24 38,1 S 813 32 24 2 S 813 32 32 2 2 50 32 50,8 S 813 40 32 2 1/2 W 41 41 49 49 58 58 58 74 74 74 92 92 92 108 108 142 142 Dimensions (mm) Y 74 74 85 85 99 99 99 9 9 9 153 153 153 179 179 218 218 X 42 47 46 52 51 57 62 69 69 70 78 87 88 101 104 134 143 D 30,2 38,1 30,2 38,1 30,2 38,1 44,5 38,1 44,5 50,8 44,5 50,8 60,3 60,3 71,4 71,4 84,1 (bars) 280 210 185 170
Swage Fittings Catalogue - 83 3000 psi SAE flange SD type insert SD 811 SD 8 SD 811 3000 PSI SAE J518 FLANGE STRAIGHT Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y D (bars) SD 811 3/4 52 113 38 SD 811 16 1 58 119 44,5 SD 811 16 3/4 53 5 38 SD 811 16 16 1 25 16 25,4 1 59 131 44,5 SD 811 20 16 1 1/4 63 135 51 250 SD 811 20 20 1 1/4 64 151 51 250 1 1/4 32 20 31,8 SD 811 24 20 1 1/2 69 156 60,5 200 SD 811 24 24 1 1/2 69 163 60,5 1 1/2 40 24 38,1 SD 811 32 24 2 74 168 71,5 200 SD 811 32 32 2 50 32 50,8 2 76 173 71,5 200 SD 8 3000 PSI SAE J518 FLANGE 45 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y X D (bars) SD 8 3/4 63 5 27 38 SD 8 16 1 67 9 31 44,5 SD 8 16 3/4 78 151 31 38 SD 8 16 16 1 25 16 25,4 1 79 152 32 44,5 SD 8 20 16 1 1/4 80 153 33 51 250 SD 8 20 20 1 1/4 99 187 39 51 250 1 1/4 32 20 31,8 SD 8 24 20 1 1/2 99 187 39 60,5 200 SD 8 24 24 1 1/2 117 211 46 60,5 1 1/2 40 24 38,1 SD 8 32 24 2 118 2 47 71,5 200 SD 8 32 32 2 50 32 50,8 2 152 250 58 71,5 200 FLANGE SD 813 SD 813 3000 PSI SAE J518 FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y X D (bars) SD 813 3/4 56 118 56 38 SD 813 16 1 56 118 61 44,5 SD 813 16 3/4 72 145 67 38 SD 813 16 16 1 25 16 25,4 1 72 145 68 44,5 SD 813 20 16 1 1/4 72 145 70 51 250 SD 813 20 20 1 1/4 91 178 85 51 250 1 1/4 32 20 31,8 SD 813 24 20 1 1/2 91 178 85 60,5 200 SD 813 24 24 1 1/2 108 202 100 60,5 1 1/2 40 24 38,1 SD 813 32 24 2 108 202 102 71,5 200 SD 813 32 32 2 50 32 50,8 2 143 281 9 71,5 200
84 - Swage Fittings Catalogue 3000 psi SAE flange SC type insert FLANGE SC 811 SC 8 SC 813 SC 811 Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y D (bars) SC 811 3/4 55 106 38,1 SC 811 16 16 1 57 108 44,5 SC 811 20 20 1 1/4 55 106 50,8 280 SC 811 16 3/4 58 114,5 38,1 SC 811 16 16 16 1 58 114,5 44,5 1 25 16 25,4 SC 811 20 16 20 1 1/4 63 119,5 50,8 280 SC 811 24 16 24 1 1/2 55 115,5 60,4 210 SC 811 16 20 16 1 64 130,5 44,5 SC 811 20 20 20 1 1/4 64 130,5 50,8 280 1 1/4 32 20 31,8 SC 811 24 20 24 1 1/2 68 134,5 60,4 210 SC 811 32 20 32 2 75 141,5 71,4 210 SC 811 24 24 24 1 1/2 73 155,5 60,4 210 1 1/2 38 24 38,1 SC 811 32 24 32 2 76 158,5 71,4 210 SC 811 32 32 32 2 77 176,5 71,4 210 2 51 32 50,8 SC 811 40 32 40 2 1/2 90 186,5 84,1 175 SC 8 SC 813 3000 PSI SAE J518 FLANGE STRAIGHT 3000 PSI SAE J518 FLANGE 45 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y X D (bars) SC 8 3/4 63 114 25 38,1 SC 8 16 16 1 65 116 27 44,5 SC 8 16 3/4 81 137 31 38,1 SC 8 16 16 1 25 16 25,4 16 1 78 134 28 44,5 SC 8 20 16 20 1 1/4 78 134 28 50,8 280 SC 8 16 20 16 1 96 163 37 44,5 SC 8 20 20 1 1/4 32 20 31,8 20 1 1/4 91 157 32 50,8 280 SC 8 24 20 24 1 1/2 91 157 32 60,4 210 SC 8 24 24 24 1 1/2 108 191 36 60,4 210 1 1/2 38 24 38,1 SC 8 32 24 32 2 107 189 35 71,4 210 SC 8 32 32 32 2 151 245 57 71,4 210 2 51 32 50,8 SC 8 40 32 40 2 1/2 146 243 51 84,1 175 3000 PSI SAE J518 FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y X D (bars) SC 813 3/4 55 106 51 38,1 SC 813 16 16 1 55 106 55 44,5 SC 813 20 20 1 1/4 55 106 60 50,8 280 SC 813 16 3/4 71 8 65 38,1 SC 813 16 16 16 1 71 8 61 44,5 1 25 16 25,4 SC 813 20 16 20 1 1/4 71 8 61 50,8 280 SC 813 24 16 24 1 1/2 71 8 61 60,4 210 SC 813 16 20 16 1 87 154 79 44,5 SC 813 20 20 1 1/4 32 20 31,8 20 1 1/4 87 154 71 50,8 280 SC 813 24 20 24 1 1/2 87 154 71 60,4 210 SC 813 24 24 24 1 1/2 105 188 83 60,4 210 1 1/2 38 24 38,1 SC 813 32 24 32 2 105 188 81 71,4 210 SC 813 32 32 32 2 140 237 2 71,4 210 2 51 32 50,8 SC 813 40 32 40 2 1/2 140 237 117 84,1 175
Swage Fittings Catalogue - 85 6000 psi SAE flange S type insert S 861 S 861 6000 PSI SAE J518 FLANGE STRAIGHT Part Hose inner diameter Collar N inch DN Dash mm inch S 861 08 08 1/2 1/2 08,7 S 861 08 3/4 S 861 08 10 1/2 5/8 16 10 15,9 S 861 10 3/4 S 861 08 1/2 S 861 3/4 S 861 16 1 S 861 16 3/4 S 861 16 16 1 25 16 25,4 1 S 861 20 16 1 1/4 S 861 16 20 1 S 861 20 20 1 1/4 32 20 31,8 1 1/4 S 861 24 20 1 1/2 S 861 24 24 1 1/2 1 1/2 40 24 38,1 S 861 32 24 2 S 861 32 32 2 50 32 50,8 2 Dimensions (mm) W 49,5 52,5 53 59,5 45,5 60 62,5 61 66,5 70,5 66 71 80,5 81 100 100 Y 82,5 89 89 95,5 86,5 101 103,5 116 1,5 5,5 7 132 141,5 151,5 170,5 176 D 31,7 41,3 31,7 41,3 31,7 41,3 47,6 41,3 47,6 54 47,6 54 63,5 63,5 79,4 79,4 (bars) 415 280 210 185 172 S 862 S 862 6000 PSI SAE J518 FLANGE 45 SWEPT ELBOW Part Hose inner diameter Collar N inch DN Dash mm inch S 862 08 08 1/2 1/2 08,7 S 862 08 3/4 S 862 08 10 1/2 5/8 16 10 15,9 S 862 10 3/4 S 862 08 1/2 S 862 3/4 S 862 16 1 S 862 16 3/4 S 862 16 16 1 25 16 25,4 1 S 862 20 16 1 1/4 S 862 16 20 1 S 862 20 20 1 1/4 32 20 31,8 1 1/4 S 862 24 20 1 1/2 S 862 24 24 1 1/2 1 1/2 40 24 38,1 S 862 32 24 2 S 862 32 32 2 50 32 50,8 2 W 63 68,5 76 81,5 83 89,5 95,5 Dimensions (mm) Y 96 101,5 1 117,5 4 130,5 136,5 108,5 163,5 1 167 116,5 171,5 134 195 138,5 200 143 203,5 162,5 233 166 244 2,5 289 X 23,5 29 23,5 29,5 29,5 36 41,5 40,5 44 48,5 50,5 55 59 58,5 70 73,5 D 31,7 41,3 31,7 41,3 31,7 41,3 47,6 41,3 47,6 54 47,6 54 63,5 63,5 79,4 79,4 (bars) 415 280 210 185 172 FLANGE
FLANGE 86 - Swage Fittings Catalogue 6000 psi SAE flange S type insert S 863 S 863 6000 PSI SAE J518 FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar N inch DN Dash mm inch S 863 08 08 1/2 1/2 08,7 S 863 08 3/4 S 863 08 10 1/2 5/8 16 10 15,9 S 863 10 3/4 S 863 08 1/2 S 863 3/4 S 863 16 1 S 863 16 3/4 S 863 16 16 1 25 16 25,4 1 S 863 20 16 1 1/4 S 863 16 20 1 S 863 20 20 1 1/4 32 20 31,8 1 1/4 S 863 24 20 1 1/2 S 863 24 24 1 1/2 1 1/2 40 24 38,1 S 863 32 24 2 S 863 32 32 2 50 32 50,8 2 W 41 41 49 49 58 58 58 74 74 74 92 92 92 108 108 142 Dimensions (mm) Y 74 74 85 85 99 99 99 9 9 9 153 153 153 179 179 218 X 42 50 47 55 52 62 70 70 75 82 84 90 96 101,8 117,8 137,2 D 31,7 41,3 31,7 41,3 31,7 41,3 47,6 41,3 47,6 54 47,6 54 63,5 63,5 79,4 79,4 (bars) 415 280 210 185 172
Swage Fittings Catalogue - 87 6000 psi SAE flange SD type insert SD 861 SD 862 SD 863 SD 861 6000 PSI SAE J518 FLANGE STRAIGHT Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y D (bars) SD 861 3/4 58 0 41,3 SD 861 16 1 60 2 47,6 420 SD 861 16 3/4 59 132 41,3 SD 861 16 16 1 25 16 25,4 1 64 137 47,6 415 SD 861 20 16 1 1/4 68 141 54 SD 861 20 20 1 1/4 69 157 54 1 1/4 32 20 31,8 SD 861 24 20 1 1/2 79 166 63,5 415 SD 861 24 24 1 1/2 40 24 38,1 1 1/2 79 173 63,5 345 SD 861 32 32 2 50 32 50,8 2 97 195 79,4 345 SD 862 Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y X D (bars) SD 862 3/4 67 9 31 41,3 SD 862 16 1 71 132 34 47,6 420 SD 862 16 3/4 78 151 31 41,3 SD 862 16 16 1 25 16 25,4 1 82 155 35 47,6 415 SD 862 20 16 1 1/4 87 160 40 54 SD 862 20 20 1 1/4 100 188 40 54 1 1/4 32 20 31,8 SD 862 24 20 1 1/2 105 193 45 63,5 415 SD 862 24 24 1 1/2 40 24 38,1 1 1/2 117 211 46 63,5 345 SD 862 32 32 2 50 32 50,8 2 154 252 60 79,4 345 SD 863 6000 PSI SAE J518 FLANGE 45 SWEPT ELBOW 6000 PSI SAE J518 FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y X D (bars) SD 863 3/4 56 118 61 41,3 SD 863 16 1 56 118 66 47,6 420 SD 863 16 3/4 72 145 67 41,3 SD 863 16 16 1 25 16 25,4 1 72 145 72 47,6 415 SD 863 20 16 1 1/4 72 145 79 54 SD 863 20 20 1 1/4 91 178 86 54 1 1/4 32 20 31,8 SD 863 24 20 1 1/2 91 178 93 63,5 415 SD 863 24 24 1 1/2 40 24 38,1 1 1/2 108 202 100 63,5 345 SD 863 32 32 2 50 32 50,8 2 143 240 131 79,4 345 FLANGE
88 - Swage Fittings Catalogue 6000 psi SAE flange SC type insert FLANGE SC 861 SC 862 SC 863 SC 861 6000 PSI SAE J518 FLANGE STRAIGHT Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y D (bars) SC 861 3/4 59 110 41,3 SC 861 16 16 1 61 1 47,6 420 SC 861 16 3/4 65 1,5 41,3 SC 861 16 16 1 25 16 25,4 16 1 65 1,5 47,6 420 SC 861 20 16 20 1 1/4 69 5,5 54 SC 861 16 20 16 1 70 136,5 47,6 SC 861 20 20 1 1/4 32 20 31,8 20 1 1/4 70 136,5 54 420 SC 861 24 20 24 1 1/2 80 146,5 63,5 SC 861 24 24 24 1 1/2 84 116,5 63,5 1 1/2 38 24 38,1 SC 861 32 24 32 2 99 181,5 79,4 420 SC 861 32 32 2 51 32 50,8 32 2 100 196,5 79,4 SC 862 6000 PSI SAE J518 FLANGE 45 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y X D SC 862 3/4 66 117 28 41,3 SC 862 16 16 1 68 118 29 47,6 SC 862 16 3/4 81 137 31 41,3 SC 862 16 16 1 25 16 25,4 16 1 80 136 30 47,6 SC 862 20 16 20 1 1/4 80 136 30 54 SC 862 16 20 16 1 96 163 37 47,6 SC 862 20 20 1 1/4 32 20 31,8 20 1 1/4 93 160 34 54 SC 862 24 20 24 1 1/2 94 161 35 63,5 SC 862 24 24 24 1 1/2 1 195 40 63,5 1 1/2 38 24 38,1 SC 862 32 24 32 2 SC 862 32 32 2 51 32 50,8 32 2 SC 863 (bars) 420 420 420 420 115 198 43 79,4 150 247 56 79,4 6000 PSI SAE J518 FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y X D SC 863 3/4 55 106 56 41,3 SC 863 16 16 1 55 106 58 47,6 SC 863 16 3/4 71 8 65 41,3 SC 863 16 16 1 25 16 25,4 16 1 71 8 64 47,6 SC 863 20 16 20 1 1/4 71 8 64 54 SC 863 16 20 16 1 87 154 79 47,6 SC 863 20 20 1 1/4 32 20 31,8 20 1 1/4 87 154 74 54 SC 863 24 20 24 1 1/2 87 154 76 63,5 SC 863 24 24 24 1 1/2 105 188 88 63,5 1 1/2 38 24 38,1 SC 863 32 24 32 2 SC 863 32 32 2 51 32 50,8 32 2 (bars) 420 420 420 420 105 188 93 79,4 140 237 3 79,4
Swage Fittings Catalogue - 89 SUPERCAT flange S type insert S 881 S 882 S 883 S 881 SUPERCAT FLANGE STRAIGHT Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y D (bars) S 881 3/4 65,5 106 41,3 S 881 16 1 67,5 108 47,6 S 881 16 16 1 71,5 6 47,6 1 25 16 25,4 S 881 20 16 1 1/4 74,5 9,5 54 280 S 881 20 20 1 1/4 75 136 54 1 1/4 32 20 31,8 S 881 24 20 1 1/2 82 143 63,5 210 S 881 24 24 1 1/2 40 24 38,1 1 1/2 83 153 63,5 185 S 882 Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y X D (bars) S 882 3/4 94 135 40 41,3 S 882 16 1 99 140 45 47,6 S 882 16 16 1 1 170,5 47,5 47,6 1 25 16 25,4 S 882 20 16 1 1/4 0 175 51,5 54 280 S 882 20 20 1 1/4 142 202,5 58 54 1 1/4 32 20 31,8 S 882 24 20 1 1/2 145 205,5 60,5 63,5 210 S 882 24 24 1 1/2 40 24 38,1 1 1/2 164 234 60 63,5 185 S 883 SUPERCAT FLANGE 45 SWEPT ELBOW SUPERCAT FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y X D (bars) S 883 3/4 58 99 67 41,3 S 883 16 1 58 99 75 47,6 S 883 16 16 1 74 9 80 47,6 1 25 16 25,4 S 883 20 16 1 1/4 74 9 86 54 280 S 883 20 20 1 1/4 92 153 94 54 1 1/4 32 20 31,8 S 883 24 20 1 1/2 92 153 98 63,5 210 S 883 24 24 1 1/2 40 24 38,1 1 1/2 108 179 103 63,5 185 FLANGE
90 - Swage Fittings Catalogue SUPERCAT flange SD type insert FLANGE SD 881 SD 882 SD 883 SD 881 SUPERCAT FLANGE STRAIGHT Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y D (bars) SD 881 3/4 64 6 41,3 SD 881 16 1 65 7 47,6 420 SD 881 16 16 1 69 142 47,6 1 25 16 25,4 SD 881 20 16 1 1/4 72 145 54 415 SD 881 20 20 1 1/4 73 161 54 1 1/4 32 20 31,8 SD 881 24 20 1 1/2 80 168 63,5 415 SD 881 24 24 1 1/2 40 24 38,1 1 1/2 81 175 63,5 345 SD 882 Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y X D (bars) SD 882 3/4 73 135 37 41,3 SD 882 16 1 76 137 39 47,6 420 SD 882 16 16 1 87 160 40 47,6 1 25 16 25,4 SD 882 20 16 1 1/4 88 161 41 54 415 SD 882 20 20 1 1/4 102 189 42 54 1 1/4 32 20 31,8 SD 882 24 20 1 1/2 108 196 48 63,5 415 SD 882 24 24 1 1/2 40 24 38,1 1 1/2 0 214 49 63,5 345 SD 883 SUPERCAT FLANGE 45 SWEPT ELBOW SUPERCAT FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm inch W Y X D (bars) SD 883 3/4 55 117 70 41,3 SD 883 16 1 55 117 73 47,6 420 SD 883 16 16 1 71 144 79 47,6 1 25 16 25,4 SD 883 20 16 1 1/4 71 144 82 54 415 SD 883 20 20 1 1/4 90 177 89 54 1 1/4 32 20 31,8 SD 883 24 20 1 1/2 90 177 97 63,5 415 SD 883 24 24 1 1/2 40 24 38,1 1 1/2 107 201 105 63,5 345
Swage Fittings Catalogue - 91 SUPERCAT flange SC type insert SC 881 SC 882 SC 883 SC 881 SUPERCAT FLANGE STRAIGHT Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y D D RING SC 881 3/4 84 135 41,3 DR SC 881 16 16 1 84 135 47,6 DR16 SC 881 16 16 16 1 90 146,5 47,6 DR16 1 25 16 25,4 SC 881 20 16 20 1 1/4 90 146,5 54 DR20 SC 881 20 20 20 1 1/4 88 154,4 54 DR20 1 1/4 32 20 31,8 SC 881 24 20 24 1 1/2 88 154,5 63,5 DR24 SC 881 24 24 24 1 1/2 84 166,5 63,5 DR24 1 1/2 38 24 38,1 SC 881 32 24 32 2 SC 881 32 32 2 51 32 50,8 32 2 (bars) 420 420 420 110 192,5 79,4 DR32 420 130 226,5 79,4 DR32 SC 882 SUPERCAT FLANGE 45 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y X D D RING (bars) SC 882 3/4 72 3 34 41,3 DR SC 882 16 16 1 74 5 36 47,6 DR16 420 SC 882 16 16 16 1 86 143 36 47,6 DR16 1 25 16 25,4 SC 882 20 16 20 1 1/4 86 143 36 54 DR20 420 SC 882 20 20 20 1 1/4 96 162 36 54 DR20 1 1/4 32 20 31,8 SC 882 24 20 24 1 1/2 96 162 36 63,5 DR24 420 SC 882 24 24 24 1 1/2 114 196 41 63,5 DR24 1 1/2 38 24 38,1 SC 882 32 24 32 2 116 199 44 79,4 DR32 420 SC 882 32 32 2 51 32 50,8 32 2 152 250 57 79,4 DR32 SC 883 SUPERCAT FLANGE 90 SWEPT ELBOW Part Hose inner diameter Collar Dimensions (mm) N inch DN Dash mm Dash inch W Y X D D RING (bars) SC 883 3/4 55 106 64 41,3 DR SC 883 16 16 1 55 106 64 47,6 DR16 420 SC 883 16 16 16 1 71 8 73 47,6 DR16 1 25 16 25,4 SC 883 20 16 20 1 1/4 71 8 73 54 DR20 420 SC 883 20 20 20 1 1/4 87 154 77 54 DR20 1 1/4 32 20 31,8 SC 883 24 20 24 1 1/2 87 154 78 63,5 DR24 420 SC 883 24 24 24 1 1/2 105 188 90 63,5 DR24 1 1/2 38 24 38,1 SC 883 32 24 32 2 105 188 94 79,4 DR32 420 SC 883 32 32 2 51 32 50,8 32 2 140 237 5 79,4 DR32 FLANGE
Accessories 3000 PSI 994 FLANGE 92 - Swage Fittings Catalogue 994 3000 PSI SPLIT FLANGE Split Part flange Dimensions (mm) N 3000 psi Dash K L M P R T V 994 75 08 994 77 08 1/2 3/4 8 54 65 23 26 38,1 47,6 8,7 10,5 8,7 11,1 20 22 13 14 994 78 08 994 79 08 1 1 1/4 16 20 70 80 29,2 36,3 52,4 58,7 10,5 13,1 15,1 22 22 16 14 994 79 18 994 79 28 1 1/2 2 24 32 94 102 41,1 48,2 69,9 77,8 13,5 13,5 17,9 21,4 45,4 26 16 16 994 994 Part N 994 75 46 994 76 46 994 78 56 994 79 46 994 79 76 994 79 96 3000 PSI ONE-PIECE FLANGE One-piece flange Dimensions (mm) 3000 psi Dash K L M P R T V 1/2 8 54 46,2 38,1 8,7 17,4 19,7 3/4 65 52,4 47,6 10,3 22,2 22,2 14,3 1 16 70 58,8 52,4 10,3 26,2 24 16 1 1/4 20 80 73 58,7 11,9 30,2 22,2 14,3 1 1/2 24 94 82,6 69,9 13,5 35,7 25,4 15,9 2 32 102 97 77,8 13,5 42,9 26,2 15,9
Swage Fittings Catalogue - 93 Accessories 6000 PSI 994 994 6000 PSI SPLIT FLANGE Split Part flange Dimensions (mm) N 6000 psi Dash K L M P R T V 994 79 84 994 79 85 1/2 3/4 8 57 72 24 30 40,5 50,8 8,7 10,5 9,1 11,9 22 28 16 19 994 79 86 994 79 87 1 1 1/4 16 20 81 96 35 39 57,2 66,7 13 15 13,9 15,8 32 38 24 27 994 79 88 994 79 89 1 1/2 2 24 32 113 134 48 57 79,4 96,8 17 21 18,3 22,2 42 52 30 37 994 994 Part N 994 80 84 994 80 85 994 80 86 994 80 87 994 80 88 994 80 89 6000 PSI ONE-PIECE FLANGE One-piece flange Dimensions (mm) 6000 psi Dash K L M P R T V 1/2 8 56 47,6 40,5 8,7 18,2 22 16 3/4 71 60,4 50,8 10,3 23,8 28 19 1 16 81 70 57,2 11,9 27,8 33 24 1 1/4 20 95 77,6 66,7 13,5 31,8 38 27 1 1/2 24 113 95,4 79,4 16,7 36,6 43 30 2 32 133 114,4 96,8 19,8 44,5 52 37 903 903 Part N Dash 3000 psi / 6000 psi O-RING Collar Dimensions (mm) inch ISO 3601-1 SAE 903 99 90 3/4 25X3,55 24,99X3,53 903 99 91 16 1 32,5X3,55 32,92X3,53 903 99 92 20 1 1/4 37,5X3,55 37,69X3,53 903 99 93 24 1 1/2 47,5X3,55 47,22X3,53 903 99 94 32 2 56X3,55 56,74X3,53 FLANGE
94 - Swage Fittings Catalogue ORFS S type insert S 181 S 181 MALE ORFS N inch DN Dash mm F W Y S/P G (bars) S 181 04 04 9/16-18 23,5 52 17 1/4 6 04 6,3 S 181 06 04 11/16-16 26 54,5 19 13 450 S 181 06 05 5/16 8 05 7,9 11/16-16 26 54,5 19 13 S 181 06 06 11/16-16 26 56,5 19 13 S 181 08 06 3/8 10 06 9,5 13/16-16 28 58,5 22 13 445 S 181 10 06 1-14 32,5 63 27 15 S 181 08 08 13/16-16 29 62 22 13 S 181 10 08 1/2 08,7 1-14 33,5 66,5 27 15 415 S 181 08 1 3/16-35 68 32 17 S 181 10 10 1-14 33,5 69,5 27 15 415 5/8 16 10 15,9 S 181 10 1 3/16-35 71 32 17 S 181 1 3/16-36 77 17 S 181 16 1 7/16-36,5 77,5 41 18 S 181 16 16 1 25 16 25,4 1 7/16-38 93 41 18 280 S 181 20 20 1 1/4 32 20 31,8 1 11/16-40 101 46 18 210 S 181 24 24 1 1/2 40 24 38,1 2-43 113,5 55 185 O.R.F.S S 281 S 281 FEMALE ORFS N inch DN Dash mm F W Y S/P G (bars) S 281 04 04 9/16-18 21 49,5 17 8,3 1/4 6 04 6,3 S 281 06 04 11/16-16 23 51,5 22 9,6 450 S 281 06 05 5/16 8 05 7,9 11/16-16 23 51,5 22 9,6 S 281 06 06 11/16-16 23 53,5 9,6 3/8 10 06 9,5 S 281 08 06 13/16-16 26 56,5 24 10,5 445 S 281 08 08 13/16-16 26,5 59,5 24 10,5 S 281 10 08 1/2 08,7 1-14 30 63 30 13,6 415 S 281 08 1 3/16-16 33 66 36 14 S 281 10 10 1-14 30 66 30 13,6 5/8 16 10 15,9 S 281 10 1 3/16-33 69 36 14 S 281 1 3/16-33,5 74,5 36 14 S 281 16 1 7/16-34,5 75,5 41 14,3 S 281 16 16 1 25 16 25,4 1 7/16-35,5 90,5 41 14,5 280 S 281 20 20 1 1/4 32 20 31,8 1 11/16-36 97 50 14,5 210 S 281 24 24 1 1/2 40 24 38,1 2-36,5 107 60 185
Swage Fittings Catalogue - 95 ORFS S type insert S 282 S 283 S 282 N inch DN Dash mm F W Y X S/P G (bars) S 282 04 04 9/16-18 35,5 64 17 8,3 1/4 6 04 6,3 S 282 06 04 11/16-16 37 65,5 13 22 9,6 450 S 282 06 05 5/16 8 05 7,9 11/16-16 44,5 73 14 22 9,6 S 282 06 06 11/16-16 48,5 79 22 9,6 3/8 10 06 9,5 S 282 08 06 13/16-16 51 81,5 17 24 10,5 445 S 282 08 08 13/16-16 58 91 19 24 10,5 S 282 10 08 1/2 08,7 1-14 60 93 21 30 13,6 415 S 282 08 1 3/16-62,5 95,5 23 36 14 S 282 10 10 1-14 73,5 109,5 21 30 13,6 5/8 16 10 15,9 S 282 10 1 3/16-75,7 111,5 24 36 14 S 282 1 3/16-82,5 3,5 29 36 14 S 282 16 1 7/16-85,5 6,5 32 41 14,3 S 282 16 16 1 25 16 25,4 1 7/16-103 157,5 35 41 14,3 280 S 282 20 20 1 1/4 32 20 31,8 1 11/16-7 187,5 43 50 14,5 210 S 282 24 24 1 1/2 40 24 38,1 2-141 219,5 45 60 185 S 283 FEMALE ORFS 45 SWEPT ELBOW FEMALE ORFS 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 283 04 04 9/16-18 24 52 21 17 8,3 1/4 6 04 6,3 S 283 06 04 11/16-16 24 52 24 22 9,6 450 S 283 06 05 5/16 8 05 7,9 11/16-16 31 59 27 22 9,6 S 283 06 06 11/16-16 34 64 22 9,6 3/8 10 06 9,5 S 283 08 06 13/16-16 34 64 33 24 10,5 445 S 283 08 08 13/16-16 41 74 36 24 10,5 S 283 10 08 1/2 08,7 1-14 41 74 39 30 13,6 415 S 283 08 1 3/16-41 74 42 36 14 S 283 10 10 1-14 49 85 44 30 13,6 5/8 16 10 15,9 S 283 10 1 3/16-49 85 47 36 14 S 283 1 3/16-58 99 52 36 14 S 283 16 1 7/16-58 99 56 41 14,3 S 283 16 16 1 25 16 25,4 1 7/16-74 9 62 41 14,3 280 S 283 20 20 1 1/4 32 20 31,8 1 11/16-92 153 74 50 14,5 210 S 283 24 24 1 1/2 40 24 38,1 2-108 179 83 60 185 O.R.F.S
96 - Swage Fittings Catalogue ORFS SD type insert SD 181 SD 181 MALE ORFS N inch DN Dash mm F W Y S/P G (bars) SD 181 1 3/16-34 95 32 17 420 SD 181 16 16 1 25 16 25,4 1 7/16-37 110 41 18 414 SD 181 20 20 1 1/4 32 20 31,8 1 11/16-40 8 46 18 250 SD 181 24 24 1 1/2 40 24 38,1 2-43 136 55 250 O.R.F.S SD 281 SD 282 SD 283 SD 281 N inch DN Dash mm F W Y S/P G (bars) SD 281 1 3/16-35 97 36 14 420 SD 281 16 16 1 25 16 25,4 1 7/16-37 110 41 14,3 414 SD 281 20 20 1 1/4 32 20 31,8 1 11/16-38 6 50 14,5 250 SD 281 24 24 1 1/2 40 24 38,1 2-39 132 60 250 SD 282 SD 283 FEMALE ORFS - SLIP-ON NUT FEMALE ORFS - SLIP-ON NUT 45 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) SD 282 1 3/16-63 5 26 36 14 420 SD 282 16 16 1 25 16 25,4 1 7/16-78 151 31 41 14,3 414 SD 282 20 20 1 1/4 32 20 31,8 1 11/16-96 184 36 50 14,5 250 SD 282 24 24 1 1/2 40 24 38,1 2-113 207 42 60 250 FEMALE ORFS - SLIP-ON NUT 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) SD 283 1 3/16-56 118 55 36 14 420 SD 283 16 16 1 25 16 25,4 1 7/16-71 144 67 41 14,3 414 SD 283 20 20 1 1/4 32 20 31,8 1 11/16-90 177 81 50 14,5 250 SD 283 24 24 1 1/2 40 24 38,1 2-107 201 95 60 250
Swage Fittings Catalogue - 97 ORFS SC type insert SC 181 SC 181 MALE ORFS N inch DN Dash mm F W Y S/P G (bars) SC 181 1 3/16-36 87 32 17 420 SC 181 16 16 1 25 16 25,4 1 7/16-41 97 41 18 420 SC 181 20 20 1 1/4 32 20 31,8 1 11/16-44 111 46 18 SC 181 24 24 1 1/2 40 24 38,1 2-48 131 55 290 SC 281 SC 282 SC 283 SC 281 FEMALE ORFS N inch DN Dash mm F W Y S/P G (bars) SC 281 10 1-14 43 94 30 13,6 SC 281 1 3/16-46 97 36 14 420 SC 281 16 1 7/16-49 100 41 14,3 SC 281 16 16 1 7/16-51 107 41 14,3 420 1 25 16 25,4 SC 281 20 16 1 11/16-52 109 50 14,5 SC 281 20 20 1 1/4 32 20 31,8 1 11/16-55 1 50 14,5 SC 281 24 24 1 1/2 40 24 38,1 2-60 142 60 290 SC 282 FEMALE ORFS 45 SWEPT ELBOW Code Hose inner diameter Thread Dimensions (mm) article inch DN Dash mm F W Y X S/P G (bars) SC 282 1 3/16-60 111 22 36 14 420 SC 282 16 1 7/16-61 1 23 41 14,3 SC 282 16 16 1 7/16-78 134 29 41 14,3 420 1 25 16 25,4 SC 282 20 16 1 11/16-78 134 29 50 14,5 SC 282 20 20 1 1/4 32 20 31,8 1 11/16-93 159 34 50 14,5 SC 282 24 24 1 1/2 40 24 38,1 2-113 195 41 60 290 FEMALE ORFS SC 283 90 SWEPT ELBOW Code Hose inner diameter Thread Dimensions (mm) article inch DN Dash mm F W Y X S/P G (bars) SC 283 1 3/16-54 105 48 36 14 420 SC 283 16 1 7/16-54 105 49 41 14,3 SC 283 16 16 1 7/16-71 7 62 41 14,3 420 1 25 16 25,4 SC 283 20 16 1 11/16-71 7 62 50 14,5 SC 283 20 20 1 1/4 32 20 31,8 1 11/16-87 153 75 50 14,5 SC 283 24 24 1 1/2 40 24 38,1 2-105 187 90 60 290 O.R.F.S
98 - Swage Fittings Catalogue NPT SD type insert SD 1 SD 1 MALE NPT - 60 CONE N inch DN Dash mm F W Y S/P G (bars) SD 1 3/4-14 34 98 27 19 SD 1 16 1-11,5 42 103 36 24 420 SD 1 16 16 1-11,5 42 115 36 24 1 25 16 25,4 SD 1 20 16 1 1/4-11,5 45 118 46 25 420 SD 1 20 20 1 1/4-11,5 47 135 46 25 1 1/4 32 20 31,8 SD 1 24 20 1 1/2-11,5 50 137 50 26 420 SD 1 24 24 1 1/2 40 24 38,1 1 1/2-11,5 50 144 50 27 345 SD 1 32 32 2 50 32 50,8 2-11,5 55 153 60 27 345 NPT SC type insert N.P.T SC 1 SC 1 MALE NPT - 60 CONE N inch DN Dash mm F W Y S/P G (bars) SC 1 3/4-14 39 90 27 19 420 SC 1 16 1-11,5 47 98 36 21 380 SC 1 16 3/4-14 41,5 98 32 19 420 SC 1 16 16 1 25 16 25,4 1-11,5 48,5 105 36 21 380 SC 1 20 16 1 1/4-11,5 53 109,5 46 24 325 SC 1 16 20 1-11,5 52,5 119 41 21 380 SC 1 20 20 1 1/4 32 20 31,8 1 1/4-11,5 55 1,5 46 24 325 SC 1 24 20 1 1/2-11,5 59 5,5 50 25 290 SC 1 24 24 1 1/2-11,5 61 143,5 50 25 290 1 1/2 38 24 38,1 SC 1 32 24 2-11,5 67,5 150 65 26 250 SC 1 32 32 2 51 32 50,8 2-11,5 70,5 167 65 26 250
Swage Fittings Catalogue - 99 NPT S type insert S 1 S 1 MALE NPT - 60 CONE N inch DN Dash mm F W Y S/P G (bars) S 1 02 03 1/8-27 20,6 45,6 8 3/16 5 03 4,8 S 1 04 03 1/4-18 26,5 51,5 14 14 415 S 1 02 04 1/8-27 21,1 49,1 8 S 1 04 04 1/4 6 04 6,3 1/4-18 27 55 14 14 450 S 1 06 04 3/8-18 28,6 56,6 19 14 S 1 04 05 1/4-18 27 55 14 14 S 1 06 05 5/16 8 05 7,9 3/8-18 28,6 56,6 19 14 S 1 08 05 1/2-14 34 62 22 19 S 1 04 06 1/4-18 27,5 58 16 14 450 S 1 06 06 3/8 10 06 9,5 3/8-18 28,6 59,1 19 14 450 S 1 08 06 1/2-14 34 64,5 22 19 415 S 1 06 08 3/8-18 30,6 63,6 22 19 415 S 1 08 08 1/2 08,7 1/2-14 35 68 22 19 415 S 1 08 3/4-14 36,9 69,9 27 19 S 1 08 10 1/2-14 36,2 72 25 19 5/8 16 10 15,9 S 1 10 3/4-14 37,1 72,9 27 19 S 1 3/4-14 37,9 78,4 27 19 S 1 16 1-11,5 45,5 86 35 21 280 S 1 16 3/4-14 40,4 91,4 32 19 280 S 1 16 16 1 25 16 25,4 1-11,5 47 98 35 21 280 S 1 20 16 1 1/4-11,5 51,1 102,1 46 24 210 S 1 20 20 1 1/4 32 20 31,8 1 1/4-11,5 51,9 109,6 46 24 210 S 1 24 24 1 1/2 40 24 38,1 1 1/2-11,5 55 119,4 50 25 185 S 1 32 32 2 50 32 50,8 2-11,5 64 134 65 26 165 N.P.T
S.A.E 100 - Swage Fittings Catalogue SAE S type insert S 141 S 141 MALE SAE - 0-RING N inch DN Dash mm F W Y S/P G (bars) S 141 07 04 7/16-20 23 51,5 14 S 141 08 04 1/4 6 04 6,3 1/2-20 23 51,5 17 S 141 09 04 9/16-18 24,5 53 17 250 S 141 09 05 5/16 8 05 7,9 9/16-18 24,5 53 17 250 S 141 09 06 9/16-18 24,5 55 17 3/8 10 06 9,5 S 141 06 3/4-16 26,5 57 24 250 S 141 08 3/4-16 27 60 24 250 S 141 14 08 1/2 08,7 7/8-14 30 63 25 200 S 141 17 08 1 1/16-34 67 32 200 S 141 14 10 7/8-14 30 66 25 5/8 16 10 15,9 S 141 17 10 1 1/16-34 70 32 200 S 141 17 1 1/16-35 76 200 S 141 21 1 5/16-36 77 38 160 S 141 21 16 1 25 16 25,4 1 5/16-37 92 38 160 S 131 S 131 MALE SAE - 90 CONE N inch DN Dash mm F W Y S/P G (bars) S 131 10 05 5/16 8 05 7,9 5/8-18 28,2 56,7 17 250 S 131 10 06 3/8 10 06 9,5 5/8-18 28,2 58,7 17 250 S 131 17 1 1/16-40,5 81,5 27 250 S 221 S 221 FEMALE SAE - 90 CONE N inch DN Dash mm F W Y S/P G (bars) S 221 10 05 5/16 8 05 7,9 5/8-18 17,6 46,1 22 11 250 S 221 10 06 3/8 10 06 9,5 5/8-18 16,6 47,1 22 11 250 S 221 17 1 1/16-23,2 64,2 32 14 250
Swage Fittings Catalogue - 101 SAE S type insert S 222 S 223 S 222 N inch DN Dash mm F W Y X S/P G (bars) S 222 10 05 5/16 8 05 7,9 5/8-18 47 75 18 22 11 250 S 222 10 06 3/8 10 06 9,5 5/8-18 50 81 18 22 11 250 S 222 17 1 1/16-85 5 32 32 14 250 S 223 FEMALE SAE - 90 CONE 45 SWEPT ELBOW FEMALE SAE - 90 CONE 90 SWEPT ELBOW N inch DN Dash mm F W Y X S/P G (bars) S 223 10 05 5/16 8 05 7,9 5/8-18 31 59 30 22 11 250 S 223 10 06 3/8 10 06 9,5 5/8-18 34 64 33 22 11 250 S 223 17 1 1/16-58 99 56 32 14 250 S.A.E
MISC. 102 - Swage Fittings Catalogue Metric banjo S type insert S 941 S 941 METRIC BANJO N inch DN Dash mm F W Y X T (bars) S 941 10 03 M10X1 20 45 10,2 10 S 941 03 3/16 5 03 4,8 MX1,5 21,1 46,1,1 NC S 941 14 03 M14X1,5 22,6 47,6 14,2 14 S 941 10 04 M10X1 23 51 10,2 10 S 941 04 MX1,5 23 51,1 S 941 14 04 1/4 6 04 6,3 M14X1,5 23 51 14 14 NC S 941 16 04 M16X1,5 26,5 54,5 16,2 17,5 S 941 18 04 M18X1,5 28,5 56,5 18,2 20,5 S 941 05 MX1,5 23,5 51,5,1 S 941 14 05 M14X1,5 24 52 14,2 14 5/16 8 05 7,9 S 941 16 05 M16X1,5 26,5 54,5 16,2 17,5 NC S 941 18 05 M18X1,5 28,5 56,5 18,2 20,5 S 941 14 06 M14X1,5 24 54,5 14,2 14 S 941 16 06 M16X1,5 24 54,5 16,2 17,5 S 941 18 06 3/8 10 06 9,5 M18X1,5 27 57,5 18,2 20,5 NC S 941 20 06 M20X1,5 32 62,5 20,2 23 S 941 22 06 M22X1,5 32 62,5 22,2 22,5 S 941 26 08 M26X1,5 39 72 26,5 29,5 S 941 18 08 M18X1,5 28,1 61,1 18,2 20,5 1/2 08,7 S 941 20 08 M20X1,5 28,5 61,5 20,2 23 NC S 941 22 08 M22X1,5 28,5 61,5 22,2 22,5 S 941 26 10 M26X1,5 34,7 70,5 29,5 5/8 16 10 15,9 S 941 22 10 M22X1,5 27,2 63 22,2 22,5 NC S 941 26 M26X1,5 37,5 78 26,5 29,5 S 941 30 M30X1,5 41,5 82 30,2 30 NC S 941 30 16 1 25 16 25,4 M30X1,5 43 94 30,2 37 NC 227 227 Part N 227 01 01 227 01 02 227 01 03 227 01 04 227 01 05 227 01 40 227 01 06 227 01 07 227 01 59 METRIC BANJO BOLT Thread Dimensions (mm) F W Y S/P (bars) M10X1 26 21,5 14 NC MX1,5 31 25,5 17 NC M14X1,5 37,5 30,5 19 NC M16X1,5 40 32,5 22 NC M18X1,5 44 36,5 24 NC M20X1,5 48 39,5 27 NC M22X1,5 50 41,5 28 NC M26X1,5 58 48,5 32 NC M30X1,5 64 53 36 NC
Swage Fittings Catalogue - 103 BSP banjo S type insert S 921 S 921 BSP BANJO N inch DN Dash mm F W Y X T S 921 02 03 1/8-28 20 45 10,2 10 3/16 5 03 4,8 S 921 04 03 1/4-19 22,6 47,6 13,3 14 S 921 02 04 1/8-28 23 51 10,2 10 S 921 04 04 1/4-19 23 51 13,3 14 1/4 6 04 6,3 S 921 06 04 3/8-19 26,5 54,5 16,8 17,5 S 921 08 04 1/2-14 33,5 61,5 21 23 S 921 04 05 1/4-19 24 52 13,3 14 S 921 06 05 5/16 8 05 7,9 3/8-19 26,5 54,5 16,8 17,5 S 921 08 05 1/2-14 33,5 61,5 21 23 S 921 04 06 1/4-19 24 54,5 13,3 14 S 921 06 06 3/8 10 06 9,5 3/8-19 24 54,5 16,8 17,5 S 921 08 06 1/2-14 32 62,5 21 23 S 921 06 08 3/8-19 26,5 59,5 16,8 17,5 S 921 08 08 1/2-14 28,5 61,5 21 23 1/2 08,7 S 921 10 08 5/8-14 31 64 23,1 23,5 S 921 08 3/4-14 39 72 26,5 29,5 S 921 08 10 1/2-14 27,2 63 21 23 S 921 10 10 5/8 16 10 15,9 5/8-14 28,2 64 23,1 23,5 S 921 10 3/4-14 34,7 70,5 26,5 29,5 S 921 3/4-14 37,5 78 29,5 26,5 S 921 16 1-11 39,5 90,5 33,5 37,5 S 921 16 16 1 25 16 25,4 1-11 49 100 33,5 37,5 (bars) NC NC NC NC NC NC NC NC 227 227 Part N 227 01 19 227 01 20 227 01 21 227 01 23 227 01 60 227 01 24 227 01 61 BSP BANJO BOLT Thread Dimensions (mm) F W Y S/P (bars) 1/8-28 26 21,5 14 NC 1/4-19 34,3 29,5 19 NC 3/8-19 40,5 34 22 NC 1/2-14 46 36 27 NC 5/8-14 55 45,5 30 NC 3/4-14 56 48 32 NC 1-11 69 59 41 NC MISC.
MISC. 104 - Swage Fittings Catalogue Metric stand-pipe S type insert S 511 S 511 METRIC STAND-PIPE Part Hose inner diameter Dimensions (mm) N inch DN Dash mm D W Y V (bars) S 511 06 03 6 29,5 55 23 3/16 5 03 4,8 S 511 08 03 8 29,5 55 23 415 S 511 06 04 6 27,5 55 21 320 S 511 08 04 8 29,5 58 23 450 1/4 6 04 6,3 S 511 10 04 10 31,5 60 25 450 S 511 04 32,5 61 25 450 S 511 10 05 10 31,5 60 25 5/16 8 05 7,9 S 511 05 31,5 59 25 S 511 10 06 10 28,5 59 22 330 S 511 06 31,5 62 25 445 3/8 10 06 9,5 S 511 14 06 14 34,5 65 28 445 S 511 15 06 15 30,5 61 24 250 S 511 14 08 14 35,5 68,5 28 275 S 511 15 08 15 31,5 64,5 24 250 1/2 08,7 S 511 16 08 16 36,5 69,5 29 415 S 511 18 08 18 33,5 66,5 26 160 S 511 18 10 18 33,5 69,5 26 160 S 511 20 10 5/8 16 10 15,9 20 42,5 78,5 35 S 511 22 10 22 35,5 71,5 28 160 S 511 18 18 34,5 75,5 26 160 S 511 20 20 43,5 84,5 35 215 S 511 22 22 36,5 77,5 28 160 S 511 25 25 47,5 88,5 39 S 511 25 16 25 49 104 39 165 S 511 28 16 1 25 16 25,4 28 39 94 29 100 S 511 30 16 30 53 108 43 250 S 511 30 20 30 53,5 114,5 43 210 S 511 35 20 1 1/4 32 20 31,8 35 45,5 106,5 35 100 S 511 38 20 38 58,5 119,5 48 210 S 511 38 24 38 59,5 130 48 170 1 1/2 40 24 38,1 S 511 42 24 42 47,5 118 36 100
Swage Fittings Catalogue - 105 Metric stand-pipe S type insert S 5 S 5 METRIC STAND-PIPE 45 SWEPT ELBOW Part Hose inner diameter Dimensions (mm) N inch DN Dash mm D W Y X V (bars) S 5 06 03 6 44,5 70 22,5 23 3/16 5 03 4,8 S 5 08 03 8 44,5 70 22,5 23 415 S 5 06 04 6 48 77 24 21 320 S 5 08 04 8 48 76,5 24 23 450 1/4 6 04 6,3 S 5 10 04 10 49,5 78 25,5 25 450 S 5 04 50,5 79 26,5 25 450 S 5 10 05 10 51,5 80 27,5 25 5/16 8 05 7,9 S 5 05 57,5 86 27,5 25 S 5 10 06 10 62 92,5 27,5 22 330 S 5 06 62,5 93 28,5 25 445 3/8 10 06 9,5 S 5 14 06 14 64,5 95 30,5 28 445 S 5 15 06 15 61,5 92,5 27,5 24 250 S 5 14 08 14 73,5 106,5 34 28 275 S 5 15 08 15 70,5 103,5 31 24 250 1/2 08,7 S 5 16 08 16 74 107 34,5 29 415 S 5 18 08 18 72 105 32,5 26 160 S 5 18 10 18 86,5 2,5 34 26 160 S 5 20 10 5/8 16 10 15,9 20 92,5 8,5 40,5 35 S 5 22 10 22 85,5 1,5 33 28 160 S 5 18 18 94,5 135,5 41 26 160 S 5 20 20 100,5 141,5 47 35 215 S 5 22 22 96 137 42,5 28 160 S 5 25 25 103,5 144,5 50 39 S 5 25 16 25 131 186 63 39 165 S 5 28 16 1 25 16 25,4 28 4 178 56 29 100 S 5 30 16 30 6,5 181,5 58,5 43 250 S 5 30 20 30 152,5 213,5 69 43 210 S 5 35 20 1 1/4 32 20 31,8 35 153 214 69 35 100 S 5 38 20 38 156 217 72,5 48 210 S 5 38 24 38 184 254 79 48 170 1 1/2 40 24 38,1 S 5 42 24 42 175 246 71 36 100 MISC.
MISC. 106 - Swage Fittings Catalogue Metric stand-pipe S type insert S 513 S 513 METRIC STAND-PIPE 90 SWEPT ELBOW Part Hose inner diameter Dimensions (mm) N inch DN Dash mm D W Y X V (bars) S 513 06 03 6 21 47 37,5 23 3/16 5 03 4,8 S 513 08 03 8 21 47 37,5 23 415 S 513 06 04 6 24 52 39 21 320 S 513 08 04 8 24 52 39 23 450 1/4 6 04 6,3 S 513 10 04 10 24 52 41 25 450 S 513 04 24 52 42,5 25 450 S 513 10 05 10 31 59 45 25 5/16 8 05 7,9 S 513 05 31 59 45 25 S 513 10 06 10 34 64 48 22 330 S 513 06 34 64 49 25 445 3/8 10 06 9,5 S 513 14 06 14 34 64 52 28 445 S 513 15 06 15 34 64 48 24 250 S 513 14 08 14 41 74 57,5 28 275 S 513 15 08 15 41 74 53,5 24 250 1/2 08,7 S 513 16 08 16 41 74 58,5 29 415 S 513 18 08 18 41 74 55,5 26 160 S 513 18 10 18 49 85 61,5 26 160 S 513 20 10 5/8 16 10 15,9 20 49 85 70,5 35 S 513 22 10 22 49 85 60 28 160 S 513 18 18 58 99 69 26 160 S 513 20 20 58 99 78 35 215 S 513 22 22 58 99 71 28 160 S 513 25 25 58 99 82 39 S 513 25 16 25 74 9 99 39 165 S 513 28 16 1 25 16 25,4 28 74 9 89 29 100 S 513 30 16 30 74 9 96 43 250 S 513 30 20 30 92 153 109,5 43 210 S 513 35 20 1 1/4 32 20 31,8 35 92 153 107 35 100 S 513 38 20 38 92 153 114,5 48 210 S 513 38 24 38 108 179 8 48 170 1 1/2 40 24 38,1 S 513 42 24 42 108 179 0 36 100
Swage Fittings Catalogue - 107 Metric stand-pipe S type insert S 521 S 521 FRENCH GAZ STAND-PIPE Part Hose inner diameter Dimensions (mm) N inch DN Dash mm D W Y V (bars) S 521 13 04 1/4 6 04 6,3 13,25 29,5 58 22 NC S 521 13 05 5/16 8 05 7,9 13,25 29,5 58 22 NC S 521 13 06 13,25 29,5 60 22 3/8 10 06 9,5 S 521 17 06 16,75 31,5 62 24 NC S 521 17 08 16,75 32,5 65,5 24 1/2 08,7 S 521 21 08 21,25 34,5 67,5 26 NC S 521 21 10 5/8 16 10 15,9 21,25 34,5 70,5 26 NC S 521 21 21,25 35,3 76,3 26 S 521 27 26,75 34,3 75,3 25 NC S 521 33 16 1 25 16 25,4 33,5 37,3 92,3 27 NC S 521 33 20 1 1/4 32 20 31,8 33,5 38 99 27 NC MISC.
S 491 MISC. 108 - Swage Fittings Catalogue JIS S type insert S 491 FEMALE BSP-JIS 60 INVERTED CONE N inch DN Dash mm F W Y S/P S/P1 G (bars) S 491 04 04 1/4 6 04 6,3 1/4 24 52 19 14 8,5 450 S 491 06 06 3/8 10 06 9,5 3/8 26 57 22 17 11,5 450 S 491 08 08 1/2 08,7 1/2 30 63 27 22 11,5 415 S 491 3/4 36 76 32 27 13,5 S 491 16 16 1 25 16 25,4 1 40 91 41 32 14,5 280 S 491 20 20 1 1/4 32 20 31,8 1 1/4 46 104 50 41 16 210 S 491 24 24 1 1/2 40 24 38,1 1 1/2 47 1 55 50 17 185 S 791 S 791 Part N S 791 14 04 S 791 16 05 S 791 14 06 S 791 16 06 S 791 18 06 S 791 22 08 S 791 24 08 S 791 24 10 S 791 30 S 791 33 16 S 791 36 20 S 791 42 24 FEMALE METRIC-JIS 60 INVERTED CONE Hose inner diameter Thread Dimensions (mm) inch DN Dash mm F W Y S/P S/P1 G (bars) 1/4 6 04 6,3 M14X1,5 24 52,5 19 19 10,5 NC 5/16 8 05 7,9 M16X1,5 22,2 50,7 22 19 9,5 NC M14X1,5 24 54,5 19 19 10,5 3/8 10 06 9,5 M16X1,5 22,2 52,7 22 19 9,5 NC M18X1,5 24,3 54,8 24 19 11,5 1/2 08 M22X1,5 26,5 59,5 27 27 13,5,7 M24X1,5 29,9 62,9 32 32 15 NC 5/8 16 10 15,9 M24X1,5 29,9 65,9 32 32 15 NC M30X1,5 33 74 36 36 18 NC 1 25 16 25,4 M33X1,5 34,5 89,5 41 36 21,5 NC 1 1/4 32 20 31,8 M36X1,5 42,6 103,6 46 46 20 NC 1 1/2 40 24 38,1 M42X1,5 43,5 114 50 50 19 NC
Swage Fittings Catalogue - 109 JIS flange S type insert S 891 S 891 JIS FLANGE Part Hose inner diameter Collar N inch DN Dash mm inch S 891 10 08 1/2 08,7 5/8 S 891 10 10 5/8 16 10 15,9 5/8 Dimensions (mm) W 49,3 49,3 Y 82,3 85,3 D 34 34 (bars) S 892 S 893 S 892 JIS FLANGE 45 SWEPT ELBOW Part Hose inner diameter Collar N inch DN Dash mm inch S 892 10 08 1/2 08,7 5/8 S 892 10 10 5/8 16 10 15,9 5/8 S 893 Part Hose inner diameter Collar N inch DN Dash mm inch S 893 10 08 1/2 08,7 5/8 S 893 10 10 5/8 16 10 15,9 5/8 Dimensions (mm) W Y D 71 104 70 110 JIS FLANGE 90 SWEPT ELBOW W 41 49 X 27,5 30 X 44 49 34 34 Dimensions (mm) Y 74 85 D 34 34 (bars) (bars) MISC.
MISC. 110 - Swage Fittings Catalogue Miscellaneous S type insert S 501 S 501 Part N HP WASHER STAND-PIPE Hose inner diameter Dimensions (mm) inch DN Dash mm W Y (bars) S 501 10 04 1/4 6 04 6,3 34,5 63 NC S 501 10 05 5/16 8 05 7,9 34,5 63 NC S 701 S 701 HP WASHER FEMALE METRIC 22x1.5 Part Hose inner diameter Thread Dimensions (mm) N inch DN Dash mm F W Y G (bars) S 701 22 04 1/4 6 04 6,3 M22X1,5 36,5 65 14 NC S 701 22 05 5/16 8 05 7,9 M22X1,5 36,5 65 14 NC S 701 22 06 3/8 10 06 9,5 M22X1,5 36,5 67 14 NC S 590 S 590 Part N Hose inner diameter DOUBLE-CONNECTOR Dimensions (mm) inch DN Dash mm W Y (bars) S 590 04 04 1/4 6 04 6,3 13 70 450 S 590 05 05 5/16 8 05 7,9 13 70 S 590 06 06 3/8 10 06 9,5 13 74 445 S 590 08 08 1/2 08,7 15 81 415 S 590 10 10 5/8 16 10 15,9 15 87 S 590 17 99 S 590 16 16 1 25 16 25,4 20 130 280 S 590 20 20 1 1/4 32 20 31,8 21 143 210 S 971 S 971 FARM VALVE METRIC MALE N inch DN Dash mm F W Y S/P G (bars) S 971 18 05 5/16 8 05 7,9 M18X1,5 29,3 57,8 19 16 NC S 971 18 06 3/8 10 06 9,5 M18X1,5 29,3 59,8 19 16 NC S 971 18 08 1/2 08,7 M18X1,5 30,3 63,3 19 16 NC
Swage Fittings Catalogue - 111 AQ type ferrules and inserts 5697 5697 FERRULES FOR AQ TYPE INSERT Part Hose inner diameter Dimensions (mm) N DN mm Dash inch D L Usable on hose types 5697 04 6 6,3 04 1/4 T 961 5697 06 10 9,5 06 3/8 30 57,5 T 961 T 962 5697 08,7 08 1/2 T 961 T 962 5697 19 19,1 3/4 45 69 T 961 T 962 5697 16 25 25,4 16 1 T 961 MISC. external and internal skive 5698 external and internal skive 5698 FERRULES FOR AQ TYPE INSERT Part Hose inner diameter Dimensions (mm) Usable on hose types N DN mm Dash inch D L 5698 06 6 6,3 06 3/8 T 1362 5698 08,7 08 1/2 38,3 64,5 5698 19 19,1 3/4 48,6 69 5698 16 25 25,4 16 1 T 1362 T 1362 T 1362 AQ 1 AQ 1 MALE NPT 60 CONE N inch DN Dash mm F W Y S/P G (bars) AQ 1 04 04 1/4 6 04 6,3 1/4-18 26,5 15 14 NC AQ 1 06 06 3/8 10 06 9,5 3/8-18 27,5 19 14 NC AQ 1 08 08 1/2 08,7 1/2-14 34,5 22 19 NC AQ 1 3/4-14 37,2 98 27 19 NC AQ 1 16 16 1 25 16 25,4 1-11,5 43,5 115 36 21 NC AQ 771 AQ 771 FEMALE METRIC 24 CONE 0-RING - HEAVY SERIES Part Hose inner diameter Thread Tube Dimensions (mm) N inch DN Dash mm F mm W Y S/P G AQ 771 08 04 1/4 6 04 6,3 M16x1,5 8 24 19 2,3 NC AQ 771 14 06 3/8 06 9,5 M22x1,5 14 29 27 4 NC AQ 771 16 08 1/2 08,7 M24x1,5 16 31 30 5 NC AQ 771 25 M36x2 25 39 110 46 7 NC AQ 771 30 16 1 25 16 25,4 M42x2 30 41 1 50 8,7 NC (bars)
Innovative and present for many years throughout all industries, proposed by an exclusive network of distributors, Tecalemit Flexibles remains a guarantee of quality and offers a wide range of hydraulic and pneumatic connectors Tenir au temps Parc d Activités de Kermaria 290 PONT L ABBÉ FRANCE tel : +33 2 98 82 48 48 fax : +33 2 98 82 48 49 e-mail : contact@tecalemitflexibles.com DOCUMENT 777-89