2700 John St. Markham ON, L3R 2W4 Canada T: 905-474-0555 Installation Guide Wiring 1 Switching 100-240VAC 50/60Hz, 0.3A 12VDC, 1.0A, 12W UL, cul Dimensions 1 3/4 x 2 3/4 x 1 1/8 3 Switching 100-240VAC 50/60Hz, 1.2A 12VDC, 3.0A, 36W UL, cul approved. Level 3 Dimensions 2 1/4 x 4 x 1 3/8 5 Switching 100-240VAC 50/60Hz, 1.5A 12VDC, 5.0A, 60W UL, cul, CE, FCC, CCC approved. Level 3 Dimensions 2 1/8 x 4 3/4 x 1 1/2 LED Light #22 AWG (3A/5A) Spider Connector 1. LED light panels are powered by DC12V (constant voltage) power adaptors. Do not apply any other voltages, as it may damage the panels. Warranty is void if using any other power adaptors that are not approved by Canada, 2. The power adaptor that came with your LED light panel is either a 12V/1A (12W), 12V/3A (36W), or 12V/5A(60W). Check the description information consumption of the LED light panel is less than the rated wattage of the power adaptor. This will avoid over heating of the power adaptors. 3. Any adjusted cords from the power adaptor to LED light panel should be kept as short as possible to avoid any voltage drop to the LED light (by default it is about 10 at #22AWG). 4. One power adaptor can supply power to multiple of LED light panels as long as the total wattage of the LED light panels are less than the total wattage of the power adaptor. In this case, a convenient way of connecting multiple panels is to use a spider connector (split connector). Available are 3 kinds of spider connectors (2-way, 4-way, and 6-way). The 2-way and 4-way connectors have long cables, while the 6-way connector has a short cable between each DC plug. 2P Parallel long connector 5. In case it is required to install the power adaptor in a remote location far from the LED light panels, you can cut off the DC plug and extend the cable using a larger gauge (> #16 AWG) cable to avoid any voltage drop. The wire with a solid stripe is + and the other wire is -. Reversing the polarity does not damage the LED lights. Molded T Connector 4P Parallel long connector 6P Parallel short connector 2468 22AWG 800mm White stripe + Black - 200mm Cable length as short as possible 2468 22AWG Molded T Connector + Molded DC Male Connector #16 AWG
Instruction # 6 #2 6. If multiple panels are wired to a single power adaptor, connect them in parallel instead of series to avoid voltage drop in order to maximize the light output. 7. Never apply AC power directly to the LED light panels as this will instantly damage the LEDs. 8. The brightness of different size panels are usually different. Special care has to be taken to match the brightness when they are installed together. Consult our technical support person for details. Instruction # 7 #2 Device 1. LED light panels can only be dimmed with a DC dimmer. The dimmer consists of 3 components: dimmer main body, a sensor and a wireless remote control. Connect securely the DC plug of power adaptor and the DC plug of the panels to the dimmer main body. Remove the battery protection sheet in the remote control. Point the remote control to the sensor to dim the panels. (Max/Min/On/Off +/-) 2. The dimmer capacity is up to 60W each. (large size panels with two power connectors with the total wattage exceeding 60W, you have to use 2 dimmers.) 3. To control multiple panels with one remote control pad, put all sensors together. As long as the total wattage of all panels is less than 60W, you can use one dimmer to dim multiple panels. Main Body Wiring Sensor Sensor Spider Connector Remote **Total wattage below 60W Sensor #2
2700 John St. Markham ON, L3R 2W4 Canada T: 905-474-0555 Mounting s 1. LED light panels can be mounted to any wall by using Mirror Clip, U-Channel, or simply screw mounting with pre-drilled holes in the panel. The panels are fragile and large panels could be heavy. Make sure the panels are secured to prevent damages. (Mounting accessories are not supplied, but can be purchased from any local hardware store.) 2. It is recommended, but not required, to leave a little bit space between the panels and wall for heat dissipation. The best way for heat dissipation would be to keep the back of the panels in contact with a metal sheet which is mounted to wall. 3. LED panels can be directly mounted to walls by drilling holes(at your own responsibility)at locations on the panel that are away from the sides where the LED lights and heat sinks are located. 4. LED light panels may deform (distort) due to gravity if not correctly supported with mounting products. Mounting #14 box #1 1. #14 LED lightboxes/snap frames come with mounting clips on the back. Loosen the screw to re-locate the position of the mounting clips desired. 2. You can also turn the mounting clip 180 degrees for hanging. #2 #3 3. Drilling holes into the frame and using mounting screw are another way of securing the product. Graphics Installation 1. It is recommended to print graphics on Dura-Trans materials for LED light panel/lightbox applications. Do not glue printed vinyl directly to the surface of the LED light panels/lightboxes, This could change the light distribution and make the center of the panels looks darker than other areas. 2. If multiple panels are put together to form a large panel, it is recommended to leave about 1/4 space between the graphics and the LED light panel to eliminate hot or cold spots along panel conjunction edges.
Bar Installation Guide Wiring Bar #22 AWG 1. LED light bars are powered by DC12V (constant voltage) power adaptors. Do not apply any other voltages, as it may damage the light bar. Warranty is void if using another power adaptor that are not approved by Canada. 2. adaptors - same as LED light panel 4. Wiring multiple LED light bars - same as LED light panel Spider Connector (3A/5A) 5. If required, you can install the power adaptor in a remote location from the LED light bars. You must cut off the DC plug and extend the cable using a larger gauge (> #16 AWG) wire to avoid a voltage drop. The wire with a solid strip is + and the other wire is -. Reversing the polarity does not damage the LED lights. Bar #1 Bar #2 Bar #3 Bar #4 Wiring 1. LED light bars can only be dimmed with dimmer which is a DC dimmer. The dimmer consists of 3 components: dimmer main body, a sensor and a remote control pad. Connect the DC plug of power adaptors and the DC plug of the bars to the dimmer main body, and securely insert the plug of the sensor into the dimmer main body. Remove the battery protection sheet on the remote control pad. Point the remote control to the sensor to dim up/down the bars. Main Body Bar #1 Bar #2 2. The dimmer maximum capacity is 60W. 3. To control multiple bars with one remote control pad, put all sensors together. Sensor Mounting Bars 1. Screws into brackets - Use screws supplied to screw mount the end-cap to the objects to be mounted. 2. Magnets - You can also use magnet mounting by removing the adhesive 3M tape and sticking the magnets to the objects. 3. Adhesive Tape - You can also use adhesive tape by removing protective from the tape and stick to objects.
DLC LumiSheet / Dongbu Lightec Canada / Canada Terms and Conditions Payment Terms: All POs must accompany one of the below approved payment terms for the full amount of the order prior to starting production. For extremely large volume and special custom orders see below for deposit details. C) Credit Card (Max $5000.00) Shipping: All orders are shipped F.O.B Markham, Ontario. All shipping charges will be added to invoice amount (Approved Carrier and Crating). Large / volume orders will be packed in a crate for shipping in order to avoid any possible damage during shipping. Crating dimensions Delivery Timing: Will be provided to clients to try to meet their timelines. While we endeavour to meet your delivery requirements, Canada accepts no responsibility for delays of any kind, whatsoever. Claims (Shortages / Damages): All shipments should be inspected, upon receipt, for damages and shortages. All carton(s), packing materials and damaged item(s) must be kept in original packaging as the shipper will not honour claims. In all cases, the purchaser assumes damage, notify the carrier immediately, and mark the bill of lading damaged upon receipt. In the event of Package Shortages you must cost of replacement materials or freight expenses for goods damaged or lost in transit. Canada Claims (Shortages): All shipments should be inspected, upon receipt, for shortages. of the package. Cancellation, Returns Of Orders / Product: If there is an issue with your order, please contact our Customer Service Department immediately. No cancellations are accepted once production started. No returns of any kind will be accepted, after a period of 2 weeks from shipping date. Returned products must contain a Return Authorization Number that has been approved by Customer Service. Returned products must be received in one week from date of return authorization number issued date. A re-stocking charge equal to 25% of all materials and services invoiced, together with all freight charges, apply to all returns. Product Samples: All product samples are detailed in the Canada Sample Price List. All product sample requests are to be submitted on formal PO and charged to the client at the rates provided in the sample price list. Limited Warranty: Canada ( the Manufacturer ) warrants that products shall be free from defects in materials and workmanship under normal use and proper installation for a period of two (2) years from the date of the original purchase (proof of purchase required). The exclusive remedy and entire liability under this warranty will be for repair or replacement at manufacturer s option. The above warranty shall not apply to product defects resulting from (a) improper installation or maintenance; (b) misuse, neglect or accident; (c) damage during shipping or unpacking; (d) damage from hazardous environment; (e) use of power adaptor with supply voltages replace product until the purchaser returns defective product to the Manufacturer and all balance due is paid in full. Any replacement product may be either new or like-new, and may contain remanufactured parts, equivalent to new in performance. Returned products are subject to inspection and evaluation at the Manufacturer s facility. The purchaser assumes repair or replacement and shipping cost should the returned products are deemed to be non-defective or deemed to be damaged by the purchaser. Under no circumstances, shall the Manufacturer be responsible for repair or replacement at the purchaser s facility or at any other installation site at its own cost. EXCEPT FOR THE EXPRESS WARRANTIES SET FORTH ABOVE, AND TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCTS ARE SUPPLIED ON AN AS IS BASIS AND THERE ARE NO WARRANTIES, REPRESENTATIONS OR CONDITIONS WHETHER EXPRESSED OR IMPLIED, WRITTEN OR ORAL, ARISING BY STATUTE, OPERATION OF LAW, COURSE OF DEALING, USAGE OF TRADE OR OTHERWISE, WITH RESPECT TO THE PRODUCTS. THE MANUFACTURER SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY, DURABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, INCLUDING ANY LOST PROFITS, INSTALLATION OR RE-INSTALLATION COSTS, OR OTHER INCIDENTIAL OR CONSEQUENTIAL OR PUNITIVE DAMAGES, WHETHER BASED ON CONTRACT, OR ANY OTHER LEGAL THEORY, WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR WHETHER SUCH DAMAGES ARE FORSEEABLE. IN ANY EVENT, THE TOTAL AGGREGATE LIABILITY OF THE MANUFACTURER FOR DIRECT DAMAGES SHALL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. Dongbu Lightec / Canada 2700 John St. Markham, Ontario (Canada) L3R 2W4 Tel: 905-474-0555 Fax: 905-479-0201 Email: info1@fawoocanada.com http://www.fawoocanada.com or http://www.dlc-lumisheet.com