REFERENCE LIST Rebuilding projects for paper and board mills START-UP 2012 SFT Kamenskaya, Kuwshinovo, Russia Rebuild and relocation of Kymi PM7 for test liner and fluting grades 2011 Stora Enso, Kaukopää, Finland Reeler and reel packaging rebuild 2010 Stora Enso, Imatra, Finland Rebuild of BM4 (350 000 t/a), liquid packaging board 2009 Norske Skogindustrier, Skogn, Norway Rebuild of PM1 (170 000 t/a), TMP2B, DIP 2008 Stora Enso, Imatra, Finland Rebuild of BM5 (250 000 t/a), liquid packaging board 2008 Billerud AB, Gruvön and Skärblacka Rebuilds of PM2 (72 000 t/a) at Gruvön mill and PM7 (50 000 t/a) at Skärblacka mill 2008 Stora Enso, Wisconsin Rapids, USA Rebuild of PM12, capacity 85 000 t/a 2008 JPC St. Petersburg Cardboard and Printing Plant, Russia 2007 USG Corporation, Otsego mill Chicago, USA 2007 Norske Skogindustrier ASA Saugsbrugs mill, Norway 2006 Metso Paper Ltd/ UPM Nordland paper mill, Germany Basic and complete implementation engineering for the rebuild of the BM1 production line. Capacity increase to 190 000 t/a. Rebuild of major board machine PM1 Rebuild of TMP2 plant and PM2 (285 000 t/a) Rebuild of PM3, wire width 7050 mm, 340 000 t/a 2006 M-real Oyj, Simpele, Finland Rebuild of BM3, trim 4020 mm, capacity increase to 215 000 t/a 2006 Norske Skog Albury, Australia Rebuild of PM1 newsprint machine, trim 8500 mm, capacity increase to 265 000 t/a 2005 Korsnäs, Rebuild of PM4, 7200 mm, 250 000 t/a 2005 Stora Enso, Kaukopää, Finland Rebuild of BM2, 5600 mm, 210 000 t/a 2005 Mondi Ltd, Merebank, South-Africa Rebuild of PM1, 5800 mm, 250 000 t/a 2004 Papier Gaspésia, Chandler, Quebec Canada Rebuild of PM1, 6200 mm, 200 000 t/a 2004 Stora Enso, Corbehem, Rebuild of PM5, 8600 mm, 315 000 t/a 2003 Stora Enso, Veitsiluoto, Finland Rebuild of PM3, 6600 mm, 280 000 t/a 2002 Holmen Paper AB, Hallsta Paper Mill New PM11 in existing building, 8650 mm, 330 000 t/a 2001 Madison Paper Industries, USA Rebuild of PM3, 6950 mm, 250 000 t/a 2001 Sappi Nijmegen, Netherlands Rebuild of PM7, 4830 mm, 235 000 t/a coated paper 1 (5)
2001 Kymi Paper (UPM), Artti Project Kuusankoski, Finland 2000 UPM-Kymmene, Stracel, Strasbourg Off-machine coated project and rebuild of PM8, 400 000 t/a coated paper. Paper quality changed from woodfree to woodfree coated (off-machine coating) Rebuild of PM1 from film-coated grades and on-machine supercalendering, 8720 mm, 300 000 t/a, 100 % TMP. TMP plant rebuild and new bleaching plant. 2000 Modo Paper, Husum, PM8, 6 600 mm, 300 000 t/a coated paper. Rebuild of former section to gap former. Paper quality changed from woodfree to woodfree coated (off-machine coating) 1999 Chapelle Darblay (UPM) Grand News Project, Grand Couronne, 1999 Chapelle Darblay (UPM) Grand News Project, Grand Couronne, Rebuild of PM3 coloured and improved newsprint machine to use DIP max 100 %, 5320 mm, 100 000 t/a Rebuild of PM6 newsprint machine to use DIP max 100 %, 8550 mm, 210 000 t/a 1999 Modo paper, Husum, PM7, 6600 mm, 200 000 t/a. Rebuild of former section to gap former 1999 Modo Paper, Braviken, PM52, 8600 mm, newsprint machine. Installation of soft calender and shoe press 1999 Metsä-Botnia, Kemi, Finland PM1, shoe press installation, capacity increase to 335 000 t/a 1998 Myllykoski Paper, Finland PM7, 7200 mm, 200 000 t/a. SC paper machine rebuild. Quality upgrading and production increase 1998 Modo paper, Braviken, PM51, 8600 mm, newsprint machine. Installation of soft calendar 1998 Korsnäs AB, PM5, 7350 mm, 320 000 t/a. Board machine rebuild. Quality upgrading and production increase 1997 Portucel, Viana, Portugal Rebuild of linerboard machine PM1, 6500 mm. Capacity increase to 270 000 t/a 1997 Metsä-Botnia, Kemi, Finland PM1, 6800 mm, 300 000 t/a. Board machine wet end rebuild for quality improvement comprising an on-top former 1997 Papeis Inapa, Setubal, Portugal PM3 rebuild of former section, press section, stock and white water and chemical systems 1997 Parenco B.V., Netherlands PM1 capacity increase. Rebuild of former section to Duoformer CFD 1997 Gebrüder Lang GmbH, Germany Rebuild of deinking plant for improved quality 1996 AssiDomän Frövifors, Rebuild of BM5. Capacity increase from 200 000 t/a to 370 000 t/a 1995 Iggesund Paperboard, BM2, 4750 mm, 200 000 t/a. Capacity increase and quality upgrading. Stock preparation and board machine rebuild 2 (5)
1995 SCA Ortviken, Rebuild of PM4, stock preparation, white water system, short circulation, wire section, press section, dryer section, on-machine coating and finishing. Modification of newsprint machine to matt LWC machine 1994 Stora-Feldmühle, Kvarnsveden Rebuild of PM8 wire section, newsprint 1994 Metsä-Serla, Kirkniemi, Finland Rebuild of PM1 stock preparation, white water system, wire section, press section and on-machine coater. Modification of SC paper machine for wood-containing coated printing paper 1994 Svetogorsk, Russia Rebuild of paper machine for liquid packaging board 1994 International Paper, Kwidzyn, Poland PM3, 5500 mm, 80 000 t/a. Rebuild of stock preparation shower water system, wet end, dryer section, steam and condensate system, newsprint 1993-97 Korsnäs AB, PM4, 7300 mm, 190 000 t/a. Stock preparation and board machine rebuild. Sack paper, liner board 1993 Stora-Feldmühle, Kvarnsveden 1993 Australian Newsprint Mills Ltd. Australia Rebuild of PM10, stock preparation, white water system, wire section and press section, newsprint Rebuild of PM1, white water system and wire section, newsprint 1993 Korsnäs AB, PM5 cylinder dryer section rebuild. Liner board, liquid packaging board 1993 International Paper, Kwidzyn, Poland PM2, 5350 mm, 100 000 t/a woodfree fine paper. Rebuild of wet end and speedsizer installation 1992 James River Corp. Kalamazoo, Michigan, USA 1992 Nettingsdorfer Papierfabrik Nettingsdorf, Austria Complete rebuild of cylinder machine to triple fourdrinier PM6, 7350 mm, rebuild to 275 000 t/a, test liner fluting 1991 Union Camp Corp. Eastover, USA Rebuild for alkaline conversion at uncoated printing and writing papers facility 1991 Mosinee Paper Corp, Mosinee Michigan, USA Rebuild of unbleached specialty paper machine 1991 Bachofen & Meier CH, Austria Mechanical engineering for rebuild of off-machine coater at SORA, Italy, including supervision of erection 1990 National Gypsum Co., Pryor Oklahoma, USA Rebuild of cylinder machine to dual fourdrinier 1990 SCA Ortviken, PM1, new 6400 mm, 160 000 t/a, wide LWC base PM in existing building, new coater and finishing 1990 United Paper Mills, Kajaani, Finland PM2, 6100 mm, rebuild of stock preparation, 120 000 t/a, SC paper 1990 United Paper Mills, Kajaani, Finland Rebuild of SC GWD mill screening, cleaning and reject refining 3 (5)
1990 Kymmene, Finland PM8, 8500 mm, capacity increase, Symsizer installation, woodfree fine paper 1990 Enso-Gutzeit Oy, Kaukopää, Finland BM2, 5660 mm, 180 000 t/a, rebuild of stock preparation wet end, dryer section and on-line coater, SBS board 1989 Korsnäs AB, Korsnäs, PM5, 7000 mm, 200 000 t/a, rebuild of stock preparation wet end, dryer section and on-line coater, liquid packaging board 1989 Roermond, The Nerherlands PM3, 5000 mm, 160 000 t/a, rebuild of PM testliner 1989 Enso-Gutzeit Oy, Kaukopää, Finland BM4, 6350 mm, 200 000 t/a, rebuild of wet end and stock preparation, liquid packaging board 1989 Kymmene Oy, Kaukas, Finland PM1, PM2 capacity increase, stock preparation modification. New off-machine coater No. 3, 7600 mm, rereeler, super-calender and winder, LWC 1989 Metsä-Serla, Mänttä, Finland PM8, 3400 mm, 130 t/d tissue and towel, new stock preparation, new PM with auxiliaries 1989 Parenco, Renkum, The Netherlands PM2, 8500 mm, speed up to 220 000 t/a, newsprint, quality improvement, 4 th press, new soft calendar and winder 1989 Enso-Gutzeit Oy, Summa, Finland PM3, 7300 mm, 180 000 t/a, rebuild of paper machine, including white water system, newsprint 1988 Kymmene Oy, Voikkaa, Finland PM18, 7500 mm, 176 000 t/a, dry end rebuild and new finishing section 1988 Rauma-Repola Oy, Finland PM1, 8220 mm, 185 000 t/a, rebuild, coated paper 1988 Kajaani Oy, Kajaani, Finland PM3, 7300 mm, 180 000 t/a, rebuild of paper machine, including integrated process control system, newsprint 1988 Kajaani Oy, Kajaani, Finland 100 t/d, expansion, Sunds-Defibrator, TMP 1987 Berghuizer Papierfabriek The Netherlands 1987 Crown van Gelder Papierfab. N.V. The Netherlands Rebuild of PM7 Rebuild of PM1 1987 Enso-Gutzeit Oy, Kotka, Finland PM2, 5300 mm, 120 000 t/a, rebuild of paper machine to on-machine coated-paper 1987 Enso-Gutzeit Oy, Tainionkoski Finland BM5, 5000 mm, 180 000 t/a, rebuild of wet end, liquid packaging board 1987 United Paper Mills, Kaipola, Finland PM4, 6700 mm, stock preparation and wet end rebuild, newsprint 1987 Norske Skogindustrier A/S, Skogn Norway PM2, 6700 mm, 160 000 t/a, stock preparation and wet end rebuild, newsprint 1987 PORTUCEL, Viana, Portugal BM1, 6500 mm, 260 000 t/a, rebuild, liner board 1986 S.N. Chapelle Darblay St. Etienne du Rouvray, PM4, 3800 mm, 60 000 t/a, rebuild (on-machine), LWC 4 (5)
1986 Kemi Oy, Kemi, Finland PM1, 6700 mm, 280 000 t/a, kraftliner 1985 SAICA, Zaragoza, Spain PM6, 4700 mm, 150 000 t/a, fluting, rebuild 1985 Oy Kyro Ab, Kyröskoski, Finland PM1, 3400 mm, 60 000 t/a, special boards 1985 United Paper Mills, Simpele, Finland PM3, 4000 mm, 100 000 t/a, folding box board 1985 S.N. Chapelle-Darblay Grand Couronne & St. Etienne du Rouvray, 1984 Korsnäs-Marma AB, Korsnäs PM3, 5300 mm, 85 000 t/a, newsprint PM5, 6900 mm, 130 000 t/a, LWC BM4, 7200 mm, 160 000 t/a, liquid container board 1984 AB Iggesund Bruk, BM1, 3950 mm, 120 000 t/a, SBS board rebuild of stock preparation, wet end, dryer section and on-line coater. BM2, 4700 mm, 140 000 t/a, SBS board, rebuild of on-line coater 1984 Tervakoski Oy, Tervakoski, Finland Basic engineering, PM8, 2950 mm, 20 000 t/a, cable papers 1982 Internills S.A. Ardenne, Belgium PM2 with on-machine coater, 3400 mm, 26 500 t/a woodfree coated paper 1982 Intermills S.A., Pont de Warche Belgium PM1 with billblade, 3400 mm, 25 000 t/a woodfree coated papers 1982 Intermills S.A., Steinbach, Belgium PM10, 2950 mm, 15 000 t/a, photo and ivory board 1982 Wistavarfs (SCA), Wistavarf, PM1, 5360 mm, 140 000 t/a, rebuild on kraft paper machine to make fine paper 1980 Stora Kopparberg, Kvarnsveden PM8, 5350 mm, 90 000 t/a rebuild of newsprint machine to make SC paper 1980 Tervakoski Oy, Tervakoski, Finland Basic engineering, PM11, 3500 mm, 20 000 t/a, cigarette and light weight printing papers 1980 Beghin-Say, Corbehem, Basic engineering, PM4, 6600 mm, 140 000 t/a, rebuild (on-machine), LWC 1979 Pars Paper Co Ltd, Haft Tappeh, Iran PM3, 3500 mm, 30 000 t/a printing papers from bagasse 1979 Papelera Navarra S.A., Spain PM1, 2420 mm, 45 000 t/a, fluting, testliner PM2, 2440 mm, 44 000 t/a sack paper, kraftliner 1979 Cartiere Antonio Sterzi S.p.A Crevacuore, Italy PM1, 3500 mm, 55 000 t/a, woodfree uncoated grades 1976 Melhoramentos, Caieiros, Brazil PM7, 2340 mm, 5 500 t/a, tissue PM8, 3200 mm, 24 500 t/a, tissue 1969 AB Tumba Bruk, Tumba, PM1, 1420 mm, 1 450 t/a, banknote papers 5 (5)