Foam Unit PROFOAM-R USER GUIDE

WALL Foam unit PROFOAM-R - Installation Montage des buses de calibrage Installation Tuyau Buse Clapet Correspondance des buses de calibrage: voir page HOSE SUPPORT wall plugs S7x0 S/ST washers L Ø5 S/ST Screws 5,5x8 Montage du joint filtre wall plugs S7x0 S/ST screws 5,5x8 Joint filtre IMPORTANT Respecter l orientation du joint filtre Plastic blockers wall plugs S7x0 S/ST screws 5,5x8 Montage du joint fibre Holders for wand and nozzle wall plugs S7x0 S/ST washers L Ø5 S/ST screws 5,5x8 Joint fibre S/ST HOLDER FOR ONE 5L CAN Perçage du bouchon GROUND These installation dimensions are an example Tools needed: Ø 7mm drill + philips screwdriver PACKING LIST PROFOAM-R Foam system PROFOAM -R (PVC or S-ST model) Bag compressed air connections: S/ST bull frog clips (Torro 8x) M ain water S/ST braided connection hose F/-F/ (,5m) Air quick connector Ø/x6 (LB0.08) Blue hose, 0, 5 or 0m model hose barb Ø/x0 (LB0.07) S/ST foam wand with white protection cap Bag with fixing screws for unit: S/ST screws Ø5,5x8 Blue rinsing nozzle wall plugs S7 S/ST holder for can (5L) suction line L=m Bag with gaskets: green fiber gaskets /" Yellow filter with weigth covered by plastic green fiber gaskets /" bag of 5 tips black filter gasket /" Instruction sheet Bag with fixing screws for can holder and S/ST screws Ø5,5x8 Bag with plastic blockers, screws and wall plugs hose support wall plugs S7 PVC hose support S/ST washer L Ø5 Adaptor /"F - /"M Packing box: Length=770mm, Width=00mm, Heigth=0mm - Weigth =,8 kg (with 0m hose) NTPFRSLB V.0.0 p.6/9

Foam unit PROFOAM-R Instructions for use B Foam wand with white protection A C Rinsing nozzle with blue protection D E S/ST quick coupler H G F USE IN «FOAM» MODE ) Connect the white foam wand «B» on the quick coupler «D». Please check that the wand water valve «E» is closed. ) Turn the -way valve «A» on «FOAM» position. ) the water ball valve «H». ) the air valve «G». 5) the wand water valve «E». 6) Regulate air pressure according to expected result. Unlock by pulling forward to the right the button «F» and regulate the pressure by turning the button. When the result is OK, lock the regulator with button «F». 7) After use, please close the following valves: wand «E», air «G», water «H». CAUTION ALWAYS orientate spray in direction of surfaces to treat. NEVER orientate spray in direction of people, animals or plants ALWAYS w ait few seconds for a good product and w ater mix ing. ALWAYS close w ater inlet v alv e after each use. WATER PRESSURE must be included on bar to 6 bar. MAXIMUM w orking temperature is 50 C ALWAYS keep the unit on frost protection USE IN «RISING» MODE ) Connect the blue rinsing nozzle «C» on the quick coupler «D». Please check that the wand water valve «E» is closed. ) Turn the -way valve «A» on «RINSE» position. ) the water ball valve «H». ) the wand water valve «E». 5) After use, please close wand «E» and water «H» valves. METHODE OF DILUTION CLACULATING EXEMPLE: 5 (A) x 00%=.5% 000 (B) Volume B Volume A (5 cl ou 50 ml) Volume A : Breathed product Volume B : solution (water + product) DILUTION CHART (000 cl ou 0 000 ml) Color Product Color Product Pink,00% Blue 0,00% Purple,50% White,00% Turquoise,00% Red 5,00% Yellow,00% Beige 0,00% Dark brow n,00% Black,00% Orange 5,00% Grey,00% Green 6,00% Without tip,00% Light brow n 8,00% Transparent CONDITION TESTS (this drawing is an exemple) Dynamic water pressure =,5 bar Suctioned product : Foaming detergent density: Hose lengh: 0m tuyau: 0m This table is done to help you to choose a tip according to the concentration expected.concentration désirée. NTPFRSLB V.0.0 p.7/9

Foam unit PROFOAM-R - Troubles Check valve Blue rubber handle. Compressed air regulator. WATER Air diffuser Water dynamic pressure must be between and 6 bar. / / Air valve with quick connector Suction line - PVC cristal Blue hose COMPRESSED AIR Air pressure must be between and 6 bar with a flow rate of 00 litres/mn. CLEANING or REPLACEMENT of filter gasket CLEANING of the non-return valve _Unscrew the nut of the stainless hose. _Clean or replace the filter gasket. _Reassemble the filter gasket, repect orientation Ceramical ball O ring MAINTENANCE Foam unit PROFOAM doesn't suck product. _ Check the pressure of the w ater system (minimum : bars, maximum : 6 bars) _ Check that the filter gasket is not dirty or scaled. (clean or replace) _ Check that the yellow filter of the suction line is submerged in the product, and the hose is not pinched, folded, or closed. _ Verify that the tip is not clogged. (clean or replace) 5 _Check that the yellow filter of the suction line is not dirty. (clean or replace) 6 _ Check that the spray handle is not dirty or calcified. (clean or replace) The can fills up w ith w ater 7 _ Verify that the check valve is not dirty or calcified. (clean or replace) NTPFRSLB V.0.0 p.8/9

Foam unit PROFOAM-R - Description 0 5 6 7 9 8 5 6 7 8 0 9 «PROFOAM» unit is manufactured for cleaning and disinfection of floors and surfaces. Accessories and spare parts Description Item Back plate PROFOAM-R way valve equiped Plastic blocker Check valve (EPDM seal) Tip (bag of5 pcs) 5 Suction line L=m 6 Profoam eductor equipped 7 Antipollution ball valve 8 Screws for cover (Mx0) 9 Filter gasket /" (x5) 0 S/ST braided hose F/xF/,5m Yellow filter with weigth covered by plastic Foam wand - with white cap Rising nozzle - with blue cap S/ST handle with ball valve and quick coupler 5 Air pressure regulator 6 Pressure gauge 7 Comp. Air quick connector Ø/x6 8 0m, 5m, or 0m blue hose equipped - special foam 9 PVC water pipe equipped 0 PVC rising pipie equipped PVC cover NTPFRSLB V.0.0 p.9/9