STANDARDS FOR THE MATERIALS

STANDARDILUETTELO 1(15) Kpl Standardin numero STANDARDS FOR THE MATERIALS 1 EN 10204 2004-10 Metallic products.types of inspection documents 2 EN 10079 1992-10 Definition of steel products 3 EN 10027-1 2005-08 Designation systems for steel. Part 1: Steel names, principal symbols 4 EN 10027-2 1992-07 Designation systems for steel. Part 2: Numerical system 5 EN 10056-1 1998-08 Structural steel equal and unequal leg angles Part 1: Dimensions 6 EN 10056-2 1993-09 Structural steel equal and unequal leg angles Part 2: Tolerances on shape and dimensions 7 EN 10025 1990-03 Hot rolled products of non-alloy structural steels. Technical delivery conditions 8 EN 10029 1991-04 Hot rolled steel plates 3mm thick or above. Tolerances on dimensions, shape and mass 9 EN 10051 1997-09 Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels. Tolerances on dimensions and shape EN 10025-1:2004 Hot rolled products of structural steels. Part 1: General technical delivery conditions EN 10025-2:2004 Hot rolled products of structural steels. Part 2: Technical delivery conditions for non-alloy structural steels + Korjaus EN 10025-2/AC:2005 10 EN 10034 1993-09 Structural steel I and H section- Tolerances on shape and dimensions 11 EN 10163-1 2004-12 Delivery requirements for surface condition of hot rolled steel plates, wide flats and sections Part 1: General requirements

12 EN 10163-2 EN 10163-3 STANDARDILUETTELO 2(15) 2004-12 Delivery requirements for surface condition of hot rolled steel plates, wide flats and sections Part 2: Plate and wide flats 13 EN 10219-1 2003-02 Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 1 : Technical delivery requirements 14 EN 10219-2 2003-02 Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 2 : Tolerances, dimensions and sectional properties EN 10219-1:2006-04 EN 10219-1:2006-04 15 EN 10279 2000-01 Hot-rolled steel channels. Tolerances on shape, dimensions and mass 16 EN 10113-1 1993-03 Hot-rolled products in weld able fine grain structural steels EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions EN 10025-3:2004 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels EN 10025-4:2004 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels 17 EN 10113-2 1993-03 Hot-rolled products in weld able fine grain structural steels EN 10025-1:2004 EN 10025-3:2004 18 EN 10113-3 1993-03 Hot-rolled products in weld able fine grain structural steels EN 10025-1:2004 EN 10025-4:2004 19 EN 10155 1993-06 Structural steels with improved athmospheric corrosion resistance. Technical delivery conditions EN 10025-5:2004 Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance

STANDARDILUETTELO 3(15) 20 ISO 4014 1999-09 Hexagon head bolts. Product grades A and B 21 EN 24014 1991-10 Hexagon head bolts. Product grades A and B 22 ISO 4017 1999-08 Hexagon head screws. Product grades A and B 23 EN 24017 1991-10 Hexagon head screws. Product grades A and B 24 ISO 4032 1999-08 Hexagon nuts, style 1. Product grades A and B 25 EN 24032 1991-10 Hexagon nuts, style 1. Product grades A and B 26 ISO 8992 2005-04 Fasteners. General requirements for bolts, screws, studs and nuts 27 ISO 7091 2000-06 Plain washers. Normal series. Product grade C 28 ISO 4759-1 2000-11 Tolerances for fasteners. Part 1: Bolts, screws, studs and nuts. Product grades A, B and C 29 EN 10130 + A1 1998-09 Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions 30 ISO 898-1 1999-08 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs 31 ISO 898-2 1992-11 Mechanical properties of fasteners. Part 2: Nuts with specified proof load values. Coarse thread 32 ISO 898-5 1998-08 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 5: Set screws and similar threaded fasteners not under tensile stresses 33 ISO 898-6 1994-12 Mechanical properties of fasteners. Part 6: Nuts with specified proof load values. Fine pitch thread 34 ISO 898-7 1992-11 Mechanical properties of fasteners. Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 35 Uusi versio valmistunee joulukuussa 2006

STANDARDILUETTELO 4(15) STANDARDS FOR THE WELDING PROCEDURE SPECIFICATION 36 EN 288-1 1992-02 Specification and qualification of welding procedures for metallic materials Part 1: General rules for fusion welding 37 EN 288-2 1992-02 Specification and qualification of welding procedures for metallic materials Part 2: Welding procedure specification for arc welding 38 EN 288-3 1992-02 Specification and qualification of welding procedures for metallic materials Part 3: Welding procedure tests for the arc welding of steels 39 EN 288-5 1994-08 Specification and qualification of welding procedures for metallic materials Part 5: Approval by using approved welding consumables for arc welding 40 EN 288-6 1994-08 Specification and qualification of welding procedures for metallic materials Part 6: Approval related to previous experience 41 EN 288-7 1995-05 Specification and qualification of welding procedures for metallic materials Part 7: Approval by a standard welding procedure for arc welding 42 EN 288-8 1995-05 Specification and qualification of welding procedures for metallic materials Part 8: Approval by a pre-production welding test 43 EN 29692 1994-02 Metal- arc welding with covered electrode, gas-shielded metal-arc and gas welding. Joint preparations for steel 44 EN ISO 9692-2 1998-04 Welding and allied processes. Joint preparations Part 2: Submerged arc welding of steels 45 EN ISO 13920 1996-08 Welding. General tolerances for welded constructions. Dimensions for lengths and angles. Shape and position EN ISO 15607:2003 EN ISO 15609-1:2004 EN ISO 15614-1:2004 EN ISO 15610:2003 EN ISO 15611:2003 EN ISO 15612:2004 EN ISO 15613:2004 EN ISO 9692-1:2003 Welding and allied processes. Recommendations for joint preparation. Part 1: Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels + Korjaus EN ISO 9692-2/AC:1999 46 ENV 1090-1 1996-04 Execution of steel structures Part 1: General rules and rules for buildings 47 SFS-EN 1011-1 1998-08 Welding. Recommendations for welding of metallic materials. Part 1: General guidance for arc welding -09 + Lisäys A2:2004-02

48 SFS-EN 1011-2 2001-05 49 SFS-EN 1011-3 2001-03 50 SFS-EN 1011-4 2001-03 51 SFS-EN 1011-5 2003-12 52 SFS-EN 1011-6 2006-01 53 SFS-EN 1011-7 2004-09 54 SFS-EN 1011-8 2005-03 STANDARDILUETTELO 5(15) Welding. Recommendations for welding of metallic materials. Part 2: Arc welding of ferritic steels Welding. Recommendations for welding of metallic materials. Part 3: Arc welding of stainless steels Welding. Recommendations for welding of metallic materials. Part 4: Arc welding of aluminium and aluminium alloys Welding. Recommendations for welding of metallic materials. Part 5: Welding of clad steel Welding. Recommendation for welding of metallic materials. Part 6: Laser beam welding Welding. Recommendations for welding of metallic materials. Part 7: Electron beam welding Welding. Recommendations for welding of metallic materials. Part 8: Welding of cast irons 55 SFS-EN 439 1995-02 Welding consumables. Shielding gases for arc welding and cutting + Lisäys A1:2004-02 + Lisäys A1:2004-02 + Lisäys A1:2004-02 56 SFS-EN ISO 4063 2000-05 Welding and allied processes. Nomenclature of processes and reference numbers 57 SFS-EN ISO 6947 1997-08 Welds. Working positions. Definitions of angles of slope and rotation 58 EN ISO 15607 2003-12 Welding Specification and qualification of welding procedures for metallic materials. General rules 59 CEN ISO/TR 15608 2005-10 Welding. Guidelines for a metallic materials grouping system 60 SFS-EN ISO 15609-1 2004-11 Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Part 1: Arc welding 61 SFS-EN ISO 15609-2 2002-03 Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Part 2: Gas welding 62 SFS-EN ISO 15609-3 2004-09 Specification and qualification of welding procedures for metallic materials. Welding procedures specification. Part 3: Electron beam welding 63 SFS-EN ISO 15609-4 2004-09 Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Part 4: Laser beam welding 64 SFS-EN ISO 15609-5 2004-09 Specification and qualification of welding procedures for metallic materials. Welding procedure specification. Part 5: Resistance welding

STANDARDILUETTELO 6(15) 65 EN ISO 15610 2003-11 Specification and qualification of welding procedures for metallic materials. Qualification based on tested welding consumables 66 EN ISO 15611 2003-12 Specification and qualification of welding procedures for metallic materials. Qualification based on previous welding experience 67 EN ISO 15612 2004-08 Specification and qualification of welding procedures for metallic materials. Qualification by adoption of a standard welding procedure 68 EN ISO 15613 2004-06 Specification and qualification of welding procedures for metallic materials. Qualification based on pre-production welding test 69 ISO 15614-1 2004-06 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys 70 ISO 15614-2 2005-05 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 2: Arc welding of aluminium and its alloys 71 ISO 15614-4 2005-07 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 4: Finishing welding of aluminium castings 72 ISO 15614-5 2004-03 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 5: Arc welding of titanium, zirconium and their alloys 73 ISO 15614-8: 2002-04 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 8: Welding of tubes to tube-plate joints 74 ISO 15614-10 2005-02 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 10: Hyperbaric dry welding 75 ISO 15614-11 2002-03 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 11: Electron and laser beam welding 76 ISO 15614-12 2004-08 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 12: Spot, seam and projection welding 77 ISO 15614-13 2005-02 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 13: Resistance butt and flash welding + Corrigendum 1:2005 + Corrigendum 1:2005

STANDARDILUETTELO 7(15) 78 ISO 15614-6 2006-04 Specification and qualification of welding procedures for metallic materials. Welding procedure test. Part 6: Arc and gas welding of copper and its alloys 79 EN ISO 14555 1998-10 Welding. Arc stud welding of metallic materials Uusi versio valmistunee sysksyn aikana 80 EN ISO 15620 2000-07 Welding. Friction welding of metallic materials STANDARDS FOR THE PREPARATION OF STEEL 81 ISO 9223 1992-02 Corrosion of metals and alloys. Corrosivity of atmospheres. Classification 82 EN 10238 1996-09 Automatically blast-cleaned and automatically prefabrication primed structural steel products 83 ISO 8501-1 1988-12 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings 84 ISO 8501-2 1994-12 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 2: Preparation grades of previously coated steel substrates after localized removal of previous coatings 85 ISO 8501-3 2001-12 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 3: Preparation grades of welds, cut, edges and other areas with surface imperfections 86 ISO 8503-1 1988-02 Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces Uusi versio ilmestynee lähiaikoina ISO 8501-3:2006-03 Preparation of steel substrates before application of paints and related products. Visual assessment of surface cleanliness. Part 3: Preparation grades of welds, edges and other areas with surface imperfections

STANDARDILUETTELO 8(15) 87 ISO 8503-2 1988-02 Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel 88 ISO 8503-3 1988-02 89 ISO 8503-4 1988-02 Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 3: Method for the calibration of ISO reference comparators and for determination of surface profile. Focusing microscope procedure Preparation of steel substrates before application of paints and related products. Surface roughness characteristics of blast-cleaned steel substrates. Part 4: Method for the calibration of ISO reference comparators and for determination of surface profile. Stylus instrument procedure 90 EN ISO 8504-1 2001-05 Preparation of steel substrates before application of paints and related products. Surface preparation methods. Part1: General principles 91 EN ISO 8504-2 2001-05 Preparation of steel substrates before application of paints and related products. Surface preparation methods. Part 2: Abrasive blast cleaning 92 EN ISO 8504-3 2001-05 Preparation of steel substrates before application of paints and related products. Surface preparation methods. Part 3: Hand- and power- tools cleaning 93 ISO 4628-1 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 1: General principles and rating schemes 94 ISO 4628-2 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 2: Designation of degree of blistering 95 ISO 4628-3 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 3: Designation of degree of rusting 96 ISO 4628-4 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 4: Designation of degree of cracking

STANDARDILUETTELO 9(15) 97 ISO 4628-5 2003-09 Paints and varnishes. Evaluation of degradation of paint coatings. Destination of intensity, quantity and size of common types of defect Part 5: Designation of degree of flaking 98 EN ISO 9013 2002-09 Welding and allied processes. Quality classification and dimensional tolerances of thermally cut (oxygen/fuel gas flame) surfaces 99 EN ISO 12944-1 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 1: General introduction 100 EN ISO 12944-2 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 2: Classification of environments 101 EN ISO 12944-3 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 3: Design considerations 102 EN ISO 12944-4 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 4: Types of surface and surface preparation 103 EN ISO 12944-5 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 5: Protective paint system 104 EN ISO 12944-6 1988-05 Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 6: Laboratory performance test methods 105 EN ISO 12944-7 1998 Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 7: Execution and supervision of paint work 106 EN ISO 12944-8 1998-05 Paints and varnishes. Corrosion protection of steel structures by protective paint systems. Part 8: Development of specifications for new work and maintenance 107 EN ISO 1460 1994-10 Metallic coatings. Hot dip galvanized coatings on ferrous materials. Gravimetric determination of the mass per unit area (ISO 1460:1992) 108 EN ISO 1461 1999-02 Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods 109 EN ISO 14713 1999-03 Protection against corrosion of iron and steel in structures. Zinc and aluminium coatings. Guidelines + Lisäys A1:2003

STANDARDILUETTELO 10(15) 110 ISO 7413 1984-11 Hexagon nuts for structural bolting, style 1, hot-dip galvanized (oversize tapped). Product grades A and B. Property classes 5, 6 and 8 111 ISO 2808 Paints and varnishes -- Determination of film thickness 112 EN ISO 2178 1995-01 Non-magnetic coatings on magnetic substrates. Measurement of coating thickness- Magnetic method 113 EN ISO 2064 2000-03 Metallic and other inorganic coatings. Definitions and conventions concerning the measurement of thickness 114 ISO 15184 1998-11 Paints and varnishes. Determination of film hardness by pencil test 115 ISO 7253 1996-12 Paints and varnishes. Determination of resistance to neutral salt spray (fog) ISO 9227:2006 Corrosion tests in artificial atmospheres.salt spray tests 116 SFS-EN ISO 4892-1 2001-01 Plastics. Methods of exposure to laboratory light sources. Part 1: General guidance 117 SFS-EN ISO 4892-2 2006-08 Plastics. Methods of exposure to laboratory light sources. Part 2: enon-arc lamps 118 SFS-EN ISO 4892-3 2006-08 Plastics. Methods of exposure to laboratory light sources. Part 3: Fluorescent UV lamps STANDARDS FOR THE QUALITY REQUIRMENTS 119 EN 729-1 1994-09 Quality requirements for welding. Fusion welding of metallic materials. Part 1: Guidelines for selection and use 120 EN 729-3 1994-09 Quality requirements for welding. Fusion welding of metallic materials. Part 3: Standard quality requirements EN ISO 3834-1:2005 Quality requirements for fusion welding of metallic materials. Part 1: Criteria for the selection of the appropriate level of quality requirements EN ISO 3834-3:2005 Quality requirements for fusion welding of metallic materials. Part 3: Standard quality requirements

STANDARDILUETTELO 11(15) 121 EN 729-4 1994-09 Quality requirements for welding. Fusion welding of metallic materials. Part 4: Elementary quality requirements EN ISO 3834-4:2005 Quality requirements for fusion welding of metallic materials. Part 4: Elementary quality requirements 122 EN 719 1994-08 Welding coordination. Tasks and responsibilities 123 EN 287-1 1992-02 Approval testing of welders. Fusion welding. Part 1: Steels 124 EN 1418 1997-12 Welding personnel. Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials 125 EN 473 1993-01 Qualification and certification of NDT personel. General principles STANDARDS FOR THE QUALITY LEVEL 126 EN 25817 1992-07 Arc-welded joints in steel. Guidance on quality levels for imperfection STANDARDS FOR THE INSPECTION INSTRUCTION 127 EN 12062 1997-08 Non-destructive examination of welds. General rules for metallic materials 128 EN 970 1997-02 Non destructive examination of fusion welds. Visual examination EN 287-1:2004 Qualification test of welders. Fusion welding. Part 1: Steels + Korjaus AC:2004 + Lisäys A2:2006 EN 473:2000 Non destructive testing. Qualification and certification of NDT personnel. General principles + Lisäys A1:2005 EN ISO 5817:2003 Welding. Fusionwelded joints in steel, nickel, titanium and their alloys (beam welding excluded). Quality levels for imperfections + Korjaus AC:2006 + Lisäys A2:2003 129 EN ISO 6520-1 1998-10 Welding and allied processes. Classification of geometrical imperfections in metallic materials. Part 1 : Fusion welding

STANDARDILUETTELO 12(15) 130 SFS-EN 1289 1998-08 Non-destructive examination of welds. Penetrant testing of welds. Acceptance levels + Lisäys A2:2004 131 SFS-EN 571-1 1997-08 Non destructive testing. Penetrant testing. Part 1: General principles 132 EN 1290 1998-02 Non-destructive examination of welds. Magnetic particle examination of welds 133 EN 1291 1998-02 Non-destructive examination of welds. Magnetic particle testing of welds. Acceptance levels 134 SFS-EN 1435 1998-01 Non-destructive examination of welds. Radiographic examination of welded joints 135 EN 12517-1 2006-03 Non-destructive testing of welds. Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography. Acceptance levels 136 SFS-EN 1712 1998-03 Non-destructive examination of welds. Ultrasonic examination of welded joints. Acceptance levels 137 SFS-EN 1713 1998-12 Non-destructive examination of welds. Ultrasonic examination 138 SFS-EN 1714 1998-03 Non-destructive examination of welds. Ultrasonic examination of welded joints + Lisäys A2:2003 + Lisäys A2:2003 + Lisäys A2:2004 + Lisäys A2:2004 + Lisäys A2:2004 + Lisäys A2:2004 139 SFS-EN 13480-1 2002-09 Metallic industrial piping. Part 1: General + Lisäys A1:2006 140 SFS-EN 13480-2 2002-12 Metallic industrial piping. Part 2: Materials 141 SFS-EN 13480-3 2002-09 Metallic industrial piping. Part 3: Design and calculation + Lisäys A1:2006 142 SFS-EN 13480-4 2002-09 Metallic industrial piping. Part 4: Fabrication and installation 143 SFS-EN 13480-5 2002-09 Metallic industrial piping. Part 5: Inspection and testing 144 SFS-EN 13480-6 2005-03 Metallic industrial piping. Part 6: Additional requirements for buried piping + Lisäys A1:2006 145 CEN/TR 13480-7 2002-05 Metallic industrial piping. Part 7: Guidance on the use of conformity assessment procedures 146 SFS-EN 1043-1 1996-05 Destructive tests on welds in metallic materials. Hardness testing. Part 1: Hardness test on arc welded joints

STANDARDILUETTELO 13(15) 147 SFS-EN 1043-2 1997-05 Destructive tests on welds in metallic materials. Hardness test. Part 2: Micro hardness testing on welded joints 148 EN 444 1994-02 Non-destructive testing. General principles for radiographic examination of metallic materials by - and gamma-rays STANDARDS FOR THE DESIGN 149 ISO 14122-1 2001-05 Safety of machinery. Permanent means of access to machines and industrial plants. Part 1: Choice of a fixed means of access between two levels 150 ISO 14122-2 2001-05 Safety of machinery. Permanent means of access to machines and industrial plants. Part 2: Working platforms and Walkways 151 ISO 14122-3 2001-05 Safety of machinery. Permanent means of access to machines and industrial plants. Part 3: Stairways, stepladders and guardrails 152 ISO 14122-4 2004-12 Safety of machinery. Permanent means of access to machines and industrial plants. Part 4: Fixed ladders 153 ISO 2553 1992-10 Welded, brazed and soldered joints. Symbolic representation on drawings 154 EN 22553 1994-05 Welded, brazed and soldered joints. Symbolic representation on drawings (ISO 2553:1992) 155 ISO 4354 1997-07 Wind actions on structures (Relationship between reference velocity pressure ) 156 SFS-ENV 1993-1-1 1993-11 Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings Korvataan standardeilla SFS-EN 1993-1-1:2005, SFS-EN 1993-1- 8:2005, SFS-EN 1993-1-9:2005 ja SFS-EN 1993-1-10:2005 viimeistään 2010-03-31 157 SFS-ENV 1993-1- 1/A1 D 1996-03 Eurocode 3: Design of steel structures. Part 1-1: General. General rules and rules for buildings Korvataan standardilla SFS-EN 1993-1-1:2005 viimeistään 2010-03- 31

158 SFS-ENV 1993-1- 1/A2 G 1999-11 STANDARDILUETTELO 14(15) Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings. Annex G: Design for torsion resistance --- --- 159 SFS-ENV 1993-1- 1/A2 H 160 SFS-ENV 1993-1- 1/A2 J 161 SFS-ENV 1993-1- 1/A2 N 1999-11 Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings. Annex H: Modelling of building structures for analysis 1999-11 1999-11 Eurocode 3: Design of steel structures. Part 1-1: General. General rules and rules for buildings Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings. Annex N: Opening in webs --- --- --- --- --- --- 162 SFS-ENV 1993-1- 1/A2 Z 163 SFS-ENV 1993-1-2 1996-09 164 SFS-ENV 1993-1-4 1999-02 165 SFS-ENV 1993-1-5 1999-02 166 SFS-ENV 1993-3-1 1999-02 2000-01 Eurocode 3: Design of steel structures. Part 1-1: General rules and rules for buildings. Annex Z: Determination of design resistance from tests Eurocode 3. Design of steel structures. Part 1-2: General rules. Structural fire design Eurocode 3: Design of steel structures. Part 1-4: General rules. Supplementary rules for stainless steels Eurocode 3: Design of steel structures. Part 1-5: General rules. Supplementary rules for planar plated structures without transverse loading Eurocode 3: Design of steel structures. Part 3-1: Towers, masts and chimneys. Towers and masts 167 SFS-ENV 1991-1 1995-10 Eurocode 1: Basis of design and actions on structures. Part 1: Basis of design 168 SFS-EN 1991-1-1 2002-10 169 SFS-EN 1991-1-2 2003-04 Eurocode 1: Actions on structures. Part 1-1: General actions. Densities, selfweight, imposed loads for buildings Eurocode 1. Actions on structures. Part 1-2: General actions. Actions on structures exposed to fire 170 SFS-EN 1991-1-3 2004-01 Eurocode 1: Actions on structures. Part 1-3: General actions. Snow loads --- --- Korvataan standardilla SFS-EN 1993-1-2:2005 viimeistään 2010-03- 31 Korvataan standardilla SFS-EN 1990:2002 viimeistään 2010-03-31 171 SFS-EN 1991-1-4 2005-09 Eurocode 1: Actions on structures. Part 1-4: General actions. Wind actions 172 SFS-EN 1991-1-5 2004-05 Eurocode 1: Actions on structures. Part 1-5: General actions. Thermal actions 173 SFS-EN 1991-1-6 2005-08 Eurocode 1. Actions on structures Part 1-6: General actions. Actions during execution

STANDARDILUETTELO 15(15)