Technical Data Sheet OPUS A STANDARD Full 28.0.2016 Errors and technical changes excepted
1 Notes and Warnings Attention! This description is not a substitution for the concerned product s documentation. Please do read the documentation including the manuals carefully before dealing with this product. If the safety instructions in the documentation are not followed dangerous situation can occur that can result in damages, injuries and/or death by high voltage or wrong handling. In case you do not have the correct documentation you can order it by contacting dl-opus@topcon.com. Only properly trained personnel with the correct qualification are allowed to handle the device. Attention! Do not open the housing to avoid danger to high voltages. Before touching the electric assemblies make sure that the electricity is switched off completely. If the front pane is broken the device needs to be taken out of service due to risk of injury. If perceivable damages on the device exist that can compromise the functionality, it must be taken out of service due to the danger of malfunctions. These particularly include damages to the LCD display, damages to the keyboard, damages that compromise the protection level and damages to the encoder knobs. Please note: All content is subject to change without notice. Errors and omissions excepted. Mounting and Handling 1. Do not use the cable as a handle to carry the device. 2. Mounting in clean working environment only. Dust and oil can harm the electric contacts and compromise the functionality.. Do not mount the device under the use of violence because it can cause damage.. The device must be mounted by trained personnel only into especially designed and tested systems. 5. The device must not be opened or disassembled. 6. The device is to be cleaned with a moist fuzz free cotton cloth. If necessary a mild cleaning agent can be used. Do not use acid or abrasive cleaning agents. 7. The device is to be stored in a cool and dry environment and to be protected against sun shine. 8. If the environmental temperature is beneath 10 C the reaction time of the display increases. 2 General Information Order Numbers This documentation is valid for OPUS A order numbers as follows: OPUSASN1CANF000 OPUSASN1CDSF000 OPUSASN1ISOF000 Wachendorff Projektor CoDeSys ISO-VT Landscape Portrait Older versions: Landscape OPUSASL1CANF000 OPUSASL1CDSF000 OPUSASL1ISOF000 The neutral versions (N) will substitute the portrait (P) and landscape (L) versions.
Dimensions Housing Plastic housing, colored light grey (RAL 705) with black rubber frame. Mounting Landscape or portrait Standalone In-dash
Display Type: TFT Color Graphic LCD with LED backlight Size:., 95 mm (W) x 5 mm (H) Resolution: 80 x 272 px (WQVGA), 15:9 Colors: 16.7 Mio. Brightness: typ. 00 cd/m² Contrast Ratio: typ. 00:1 Input Devices Touch Left Keypad Right Keypad Analog resistive keys with tactile feedback Blue LED backlight Lifetime 1.000.000 actuations + keys with tactile feedback Blue LED backlight Lifetime 1.000.000 actuations Indicators and Sensors Encoder Light sensor 1 Multicolor-LED Status-LED s Electromechanical encoder with 16 mechanical detents and push function Lifetime: 1 million cycles 5 Electronics Processor platform CPU: Freescale I.MX5, 52 MHz Mass storage: 1 GByte (approx. 900 MB for customer use) RAM: RTC: Buzzer 256 MByte Buffered by gold cap 60 db(a) in 0 cm distance Lifetime min. 1000h Current consumption (without external load), max. Power Mode On Low-power Sleep Off Current at 1,5 V DC 0 ma 160 ma 90 ma < ma Current at 27 V 20 ma 90 ma 55 ma < ma Power supply System supplied through terminal 0 (battery +, see pinout) and 1 (battery -, see pinout). Terminal 15 (ignition) to be used to switch on/off. Operating voltage range: 9 6 V DC Short circuit protection. Over-voltage protection up to 8V for max. 2 minutes. Inverse polarity protection up to -8 V DC.
6 Interfaces CAN Bus 2 x CAN-Interfaces according to ISO 11898, CANspecification 2.0 B active, up to 1 Mbit/s (default 250 Kbit/s, 500 Kbit/s, 750 Kbit/s and 1 Mbit/s) RS22 1 x RS22-Interface Type: EIA22 (only RxD, TxD, GND) Speed: max. 115 Kbps USB Host 2.0 Main connector: On front: Inputs 1 x Full speed 1 x USB slot High speed configurable analog/digital inputs Input impedance: > k Ohm Resolution: 10 bit (1028 digits, 1 digit = 11,7 mv) Voltage range: 0 12 V Over-voltage protection: Up to 6 V DC Short circuit protection: Up to 6 V DC Frequency: Max. signal frequency 50 Hz Outputs digital outputs Short circuit protection: Up to 6 V I max 00 ma open drain R DS,on < 1 Ohm > 100 kohm R DS,off Video-Interface Inputs: V ss Camera supply: Max. current: Output: Ethernet-Interface 1 x 10/100 Mbit/s Base T 1x analog 1 V 12 V DC 500 ma 1x camera control output (open drain) on each interface for special functionality (mirror, shutter, heating etc.), Ampacity: 00mA 7 Connectors Connectors Main: Tyco-AMP 17288-6 Mating connector (customer) Tyco-AMP -17290-7 Mating crimp contact (customer) Tyco-AMP -17221- Dummy Plug (customer) Tyco AMP -1728- Ethernet: M12 round connector, female, -pole, D-coded acc. to EN 61076-2-101 Recommended mating connector type according to IEC 61076-2-10: MM 00-Gx1-D x) A, C, I, P, R or S-type Video: M12 round connector, female, 5-pole, B-coded, acc. to EN 61076-2-101 Recommended mating connector type according to IEC 61076-2-10: MM 005-Gx1-B x) A, C, I, P, R or S-type
8 Software Operating System Linux 2.6.28 Application Programming Wachendorff Projektor Tool Optional: Codesys-Tools (.5) Optional: ISO-VT Optional: C/C++ 9 Testing and Verification CE-Compliance EU Directive 201/0/EU (EMC) according to EN 12895: Industrial Trucks Electromagnetic compatibility EN 109: Construction machinery Electromagnetic compatibility of machines with internal electrical power supply EN ISO 1982: Agricultural and forestry machinery - Electromagnetic compatibility - Test methods and acceptance criteria E1 - Type approval EU Directive ECE R 10. Protection Level (IP Code) IP 6k5 according to ISO 2065: Road Vehicles Degrees of protection (IP-Code) Protection of electrical equipment against foreign objects, water and access Electrical 12 and 2V-Systems according to ISO 16750-2: Road Vehicles Environmental conditions and testing for electrical and electronic equipment Electrical loads ISO 1500: Agricultural Engineering Electrical and electronic equipment Testing resistance to environmental conditions Mechanical ISO 16750-: Road Vehicles Environmental conditions and testing for electrical and electronic equipment Mechanical loads, Code L ISO 1500: Agricultural Engineering Electrical and electronic equipment Testing resistance to environmental conditions Mechanical Shock: Level 2 Random Vibration: Level 2 Sinusoidal Vibration: Level 2 Climate ISO 16750-: Road Vehicles Environmental conditions and testing for electrical and electronic equipment Climatic Loads Operating Temperature Range: -0 +65 C Storage Temperature Range: -0 +85 C ISO 1500: Agricultural Engineering Electrical and electronic equipment Testing resistance to environmental conditions
10 Pinout Main connector pinout Pin. No. 1 2 5 6 7 8 9 10 11 12 1 1 15 16 17 18 19 20 21 22 2 2 25 26 Assignment VCC Ignition Input GND CarGND n. c. n. c. n. c. CAN1H CAN1L CAN2H CAN2L USB_VCC USB_GND USB_D- USB_D+ RS22 RxD RS22 TxD RS22 GND A/DI A/DI1 A/DI2 A/DI SERV_EN DO DO1 DO2 Description supply voltage +; terminal 0 ignition input; terminal 15 supply voltage - ;terminal 1 Car GND Not connected Not connected Not connected CAN 1 high CAN 1 low CAN 2 high CAN 2 low USB +5V supply USB supply GND USB Data - USB Data + RS22 receive data RS22 transmit data RS22 GND analog/digital input analog/digital input 1 analog/digital input 2 analog/digital input service enable digital output digital output 1 digital output 2 View on rear side of the A 1 7 8 1 1 19 20 26
Video connector pinout Ethernet connector pinout 1 2 5 Round Connector, 5 pins, M12 VidSig+ Mirror Camera+ Camera - VidSig GND 1 2 Round Connector, pins, M12, acc. To IEC 61076-2-101 TD+ RD+ TD- RD- Video connector, M12, female, 5 pins, b-coded, view on rear side of the A Ethernet connector, M12, female, pins, d-coded, view on rear side of the A 1 2 1 2 5 Recommended mating connector type according to IEC 61076-2-10: MM 005-Gx1-B x) A, C, I, P, R or S-type Recommended mating connector type according to IEC 61076-2-10: MM 00-Gx1-D x) A, C, I, P, R or S-type 11 Mounting accessories (not included) Standalone mounting adaptor for RAM mounting system (OPUSAZBAH001) Material PC+ABS Dimensions 7x8x2 mm (WxHxD) Operating Temperature -0 +75 C Storage Temperature -0 +85 C Max mounting torque 2.5 ± 0.2 Nm