FOR 1962-65 APPLCATON T AAW KT O NOT UPPORT T U OF A FACTORY ATR. A A RPLACNT FOR T ATR, W UGGT T U OF A VOLTTR NTA. GAUG TRNAL KT 92965220 A BN PROV FOR YOU TO CONNCT T CLUTR KT TO AN AFTRARKT GAUG CLUTR OR PARAT GAUG. Classic Update eries CONNCTOR This connector will plug into the mating connector A of the ash arness (bag G). Connect the wires as follows: Wire Color Function escription PNK 12V gnition This loose wire is used with an Oil Pressure Warning Lamp (All 62-65 Fairlane) or as the ignition feed with any Aftermarket Gauge Cluster using gauges, a tach, or a brake warning lamp. Plug this wire into connector in the cavity indicated (see page 3). Route this wire to the Oil Pressure Warning Lamp (see page 3), cut to length and install terminal K, and plug into lamp socket G. GRAY nstrument Lamps Route this wire to the Cluster nstrument Lamps (see pages 3 and 4). This will require an in-line splice of the wires to be able to accom modate each of the lamps. lide lamp socket over each wire and install terminal. BLACK Ground Route this wire to a good Cluster ground screw (see pages 3 and 4), cut to length, install ring terminal Q. Connect to a good Cluster ground using an existing Cluster housing or Const Voltage Regulator screw. BROWN Accessory Voltage Route this wire to the input side of the Const Voltage Regulator (CVR NOT UPPL, see pages 3 and 4), cut to length, install terminal O, and plug into connector N, now connect to the CVR. Take the cut off portion of the wire and slide on sleeve P, then install terminal L, slide P over L and connect to the output side of the CVR. Route the other end of the wire to the closest gauge, cut to length and install a ring terminal supplied from the Gauge Terminal Kit. f there are multiple gauges, you will need to make separate jumper wires using the ring terminals from the Gauge Terminal Kit to supply power to all of the gauges. Attach the ring terminals to the gauges with the included 10-32 locknuts. CONNCTOR This connector will plug into mating connector B of the ash arness (bag G). Connect the wires as follows: FOR ALL APPLCATON (see pages 3 and 4): LGT BLU Left Turn Lamp Route this wire to the Left and Turn ignal ndicator Lamp, cut to length, slide on lamp socket, and install terminal. ARK BLU Right Turn Lamp Route this wire to the Right and Turn ignal ndicator Lamp, cut to length, slide on lamp socket, and install terminal. LGT GRN i Beam Lamp Route this wire to the igh Beam ndicator Lamp, cut to length, slide on lamp socket, and install terminal. ARK GRN Temperature ender Route this wire to the Temperature Gauge, cut to length, install a ring terminal from the Gauge Terminal Kit, and attach to the Temperature Gauge using a supplied 10-32 locknut. TAN Fuel Gauge ender Route this wire to the Fuel Gauge, cut to length, install a ring terminal from the Gauge Terminal Kit, and attach to the Fuel Gauge using a supplied 10-32 locknut. ARK BLU Oil Pressure ender FOR T OL PRUR WARNNG LAP All Fairlane (see page 3): Route this wire to the Oil Pressure Warning Lamp, cut to length, slide on lamp socket G and spring J, and install terminal. FOR T OL PRUR GAUG All eteors (see page 4): Route this wire to the back of the gauge, cut to length, and install a ring terminal from the Gauge Terminal Kit and attach to the Oil Pressure Gauge using a supplied 10-32 locknut. page 1 www.americanautowire.com 856-933-0801 Classic Update eries 1962-65 Ford Fairlane 1962-63 ercury eteor NTRUNT CLUTR 510555 bag
FOR 1962-65 APPLCATON CONNCTOR F This connector will plug into mating connector C of the ash arness (bag G). Connect the wires as follows: Classic Update eries OTR LOO WR: This connector is only used when using an Aftermarket lectric peedometer (see page 6). Follow the manufacturer s instructions when installing these wires. f you are using a stock or mechanical aftermarket speedometer, you may discard this connector and wires. Wire Color Function escription WT Tachometer Used only with an Aftermarket Tachometer. Plug this loose wire into connector (see pages 3 and 4). Route the other end of this wire to the Tachometer, cut to length, and install onto your Tachometer pulse location. TAN Brake Light/witch Used only with an upgraded Brake ystem which includes a Brake Warning Lamp. Route this wire to the ground side of your Brake Warning Lamp. TYPCAL AFTRARKT GAUG CONNCTON (see page 5). www.americanautowire.com 856-933-0801 G J K L N O P Q page 2
Classic Update eries customer s original const voltage regulator (not supplied with kit) keyed 12v feed, to const voltage regulator (original / green 4 required for 1962 Fairlane N O L P U T T TO CONNCT TO AN ORGNAL 1962-65 FARLAN instrument lamps (original blue/red feed from const voltage regulator, to factory fuel and temp gauges (original /green to cluster housing Q x x to oil pressure warning lamp (original /red K J G 12V ignition source (Can be used for aftermarket 12V gauges, tach, or brake warning light) (original / green plug PNK 12v ign wire in R Tach out to negative coil (For aftermarket tach) Aftermarket brake warning light (ground side) to temp gauge post (original red/ dk green plug WT tach wire in R to fuel gauge post (original yellow/ wire) x R turn (original / blue L turn lt green lt blue hi beam plug TAN brake warning light wire in R. CONNCTOR A CONNCTOR B page 3
Classic Update eries customer s original const voltage regulator (not supplied with kit) keyed 12v feed, to const voltage regulator (original / green N O U T T TO CONNCT TO AN ORGNAL 1962-63 TOR instrument lamps (original blue/red L P feed from const voltage regulator, to factory fuel, temp and oil pressure gauges (original /green to cluster housing Q x x aftermarket 12v feed for gauges, tach or brake warning light (original /green Tach out to negative coil (For aftermarket tach) to temp gauge post (original red/ Aftermarket brake warning light (ground side) to oil gauge post (original /red plug PNK 12v ign wire in R dk green plug WT tach wire in R to fuel gauge post (original yellow/ wire) x R turn (original / blue L turn lt green lt blue hi beam plug TAN brake warning light wire in R. CONNCTOR A CONNCTOR B page 4
nstrument Cluster Lead Wires TYPCAL AFTRARKT GAUG CONNCTON (BLA TYP CONNCTON OWN) LFT TURN N G BA N RGT TURN N Classic Update eries Water (dash lights) Water Volts dk green (temperature) Volts lt blue (L turn ind) Tachometer (12V ignition) Tachometer lt green (hign beam ind) / (speedo ground) PO 12v peedometer V (tach - coil) peedometer (dash lights) purple (V signal) (R turn ind) TURN GNAL AN -BA LAP CONNCTON GAUG CONNCTON purple/ (V power) (12V ignition) Oil Oil (oil pressure) yellow (V ground) / (speedo power) Fuel Fuel (12V ignition) (fuel gauge) 15 11 14 151 401 400 402 139 30 31 121 39 35 8 page 5 LAP CONNCTON 150
Classic Update eries purple A B C F x purple yellow F F dash harness connector (bag G) CONNCTOR C TYPCAL LCTRC PO CONNCTON Below are some general instructions for hooking up an electric speedometer. This connector and these instructions will ONLY be used in the event that you are utilizing an aftermarket electric speedometer. f your car does NOT have an electric speedometer, this connection will NOT be used and should not be plugged onto your dash harness. t is best to consult the speedometer manufacturer s instructions if you have any questions. Yellow V Ground Connect to V - on speedometer. Purple V ignal Connect to V input on speedometer. Purple/White V Power Connect to 12V power on speedometer. Black/White peedo Ground Connect to ground on speedometer. Pink/White peedo Power Connect to 12v power on speedometer. NOT: This wire will double onto the same stud as the purple/ V power wire from above. page 6